1.28 and 5.12 Gbps multi-channel twinax cable receiver ASICs for the ATLAS Inner Tracker Pixel Detector Upgrade
Listen
Radio episode about this paper
Transcript
Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.
Kai: We're looking at the paper: "1.28 and 5.12 Gbps multi-channel twinax cable receiver ASICs for the ATLAS Inner Tracker Pixel Detector Upgrade".
Mira: Here's the gist of the paper. We present two prototypes of a gigabit transceiver ASIC, GBCR1 and GBCR2, both designed in a 65-nm CMOS technology for the ATLAS Inner Tracker Pixel Detector readout upgrade<ref:2008.09738#pg2> The single most informative sentence about the paper's subject and finding is: We present two prototypes of a gigabit transceiver ASIC, GBCR1 and GBCR2, both designed in a 65-nm CMOS technology for the ATLAS Inner Tracker Pixel Detector readout upgrade<ref:2008.09738#pg2>.
Kai: Prototype Descriptions GBCR1 has four upstream receiver channels and one downstream transmitter channel with pre-emphasis<ref:2008.09738#pg2> Each upstream channel receives the data at 5.12 Gbps through a 5 meter AWG34 Twinax cable from an ASIC driver located on the pixel module and restores the signal from the high frequency loss due to the low mass cable<ref:2008.09738#pg2> The downstream driver is designed to transmit the 2.56 Gbps signal from lpGBT to the electronics on the pixel module over the same cable<ref:2008.09738#pg2> GBCR2 has seven upstream channels and two downstream channels<ref:2008.09738#pg2> Each upstream channel works at 1.28 Gbps to recover the data directly from the RD53B ASIC through a 1 meter custom FLEX cable followed by a 6 meter AWG34 Twinax cable<ref:2008.09738#pg2> The downstream is designed to transmit the 160 Mbps signal from lpGBT through the same cable connection to RD53B and the jitter is about 157 ps at the cable ends<ref:2008.09738#pg2>.
Mira: Equalization Techniques The equalizer used in GBCR1 is based on a CTLE structure<ref:2008.09738#pg2> The passive resistor and capacitor create a zero and a pole in the transfer function to compensate for channel loss<ref:2008.09738#pg2> The equalization strength is determined by the ratio of the zero and the pole, as described in formula 3, EqualizationS trength = ωZ / ωp1 = 1 + RSCS squared (3)<ref:2008.09738#pg2> In GBCR2, a three-stage structure of CTLE is adopted to compensate with 3 order zero for high frequency range<ref:2008.09738#pg2> For the medium and low frequency parts, each of them just employs one CTLE stage to recover the signal loss in their range respectively<ref:2008.09738#pg2> The entire equalizer stage can provide 30 dB peaking strength at most<ref:2008.09738#pg2>.
Kai: Performance Metrics and Testing The peak-peak jitter (throughout the paper jitter is always peak-peak unless specified) of the restored signal is 35.4 ps at the output of GBCR1, and 138 ps for the downstream channel at the cable ends<ref:2008.09738#pg2> When the CDR is off and the retiming is bypassed, the peak-peak jitter is 79 ps and the random jitter is 4.3 ps (RMS) under the resistance setting of 0 and the capacitance setting of 3 of the equalizers<ref:2008.09738#pg2> When the CDR is turned on, the retiming circuit reduces the peak-peak jitter to 35 ps and the random jitter 1.5 ps (RMS)<ref:2008.09738#pg2> The total power consumption of GBCR1 is 192 mW<ref:2008.09738#pg2>.
Paper summary: Mira: Thinking about the whole paper, the title "one point two eight and five point one two Gbps multi-channel twinax cable receiver ASICs for the ATLAS Inner Tracker Pixel Detector Upgrade" really sums up what they did one <ref:2008.09738#pg1,1.28 and 5.12 Gbps multi-channel twinax cable receiver ASICs>.
Kai: It’s about presenting these two specific hardware solutions, GBCR1 and GBCR2, designed in sixty-five-nm CMOS technology for that specific detector upgrade one <ref:2008.09738#pg1,65-nm CMOS technology for>.
Lev: And the implication is that this work provides a tested design for handling gigabit per second data over low-mass electrical cables in a high radiation environment two.
Mira: It shows how different equalization techniques, like the CTLE structures, can be tuned to compensate for cable loss based on cable length one <ref:2008.09738#pg1>.
Kai: And they’ve shown that even with those adjustments, you can manage the jitter performance down to thirty-five picoseconds when the clock recovery is active two.
Lev: It proves that you can meet those demanding signal integrity targets for data transmission in that system, especially considering the radiation exposure two.
Mira: So, this paper lays out a blueprint for how to build these crucial receiver components needed for the ATLAS upgrade hardware one <ref:2008.09738#pg1>.
Conclusion: Kai: So, we’ve seen these two chip designs, GBCR1 and GBCR2, built in sixty-five nano meter silicon for that ATLAS detector upgrade one.
Mira: Yeah, the title itself is pretty specific: "one point two eight and five point one two gigabit per second multi-channel twinax cable receiver ASICs for the ATLAS Inner Tracker Pixel Detector Upgrade" one.
Lev: It’s about putting these chips into a real system where you’ve got these long, low-mass cables connecting everything two.
Kai: So, what does this mean when you look at the authors and the actual goals?
Mira: The goal is clearly to get data from that pixel detector readout working reliably over those specific cable lengths and speeds one.
Lev: But it’s a very constrained environment, especially because you have to worry about radiation, so they tested it with gamma rays up to two hundred kilo gray two.
Kai: So what are the big takeaways from these prototypes? What’s the actual result of all that simulation and testing?
Mira: They show GBCR1 with four upstream channels and one downstream channel using a CTLE structure for equalization one.
Lev: And they managed to keep the peak-to-peak jitter down to thirty five point four picoseconds at the output when the clock recovery is on two.
Kai: That’s pretty tight for high speed data, especially with those cable losses involved. But what about GBCR2?
Mira: GBCR2 has seven upstream channels and two downstream channels, working at a slower one point two eight gigabit per second for the upstream part one.
Lev: The downstream channel is optimized for one hundred sixty megabits per second, and they managed to reduce the interference jitter from five hundred picoseconds down to one hundred fifty seven picoseconds two.
Kai: So, it seems like these designs are making a very specific kind of data transmission possible in that detector setup.
Mira: Exactly. It shows how you can engineer those equalization stages with the right zero and pole placement to handle the channel loss effectively one.
Lev: The power consumption is also being managed pretty well; one chip uses about one hundred ninety two milli watts, which is reasonable for this kind of function two.
Kai: It’s a solid piece of hardware design, especially when you factor in that it survived the required radiation dose.
Mira: And they’re looking forward to testing GBCR2 soon to see how it performs in the actual lab setup.
Lev: It feels like a practical step toward getting those high-bandwidth links operational for the real ATLAS detector data.
Chufeng Chena, Datao Gonga, Suen Houc, Guangming Huangb, Xing Huanga, Szymon Kulisd, Paul Lerouxe, Chonghan Liua, Tiankuan Liua, Paulo Moreirad, Jeffery Prinziee, Peilong Wanga, Jingbo Yea
Department of Physics, Southern Methodist University · Department of Physics, Central China Normal University · Institute of Physics, Academia Sinica · Microelectronic group at CERN · KU Leuven
physics.ins-det
Submitted: 2020-08-22
Updated: 2020-08-22
Comments: 7 pages, 15 figures
Journal ref: Nuclear Inst. and Methods in Physics Research, A 981 (2020) 164439
DOI: 10.1016/j.nima.2020.164439
License: http://arxiv.org/licenses/nonexclusive-distrib/1.0/
Importance score: 72/100
The gist: We present two prototypes of a gigabit transceiver ASIC, GBCR1 and GBCR2, both designed in a 65-nm CMOS technology for the ATLAS Inner Tracker Pixel Detector readout upgrade<ref:2008.09738#pg2> The…
Key concepts
- Gigabit Transceiver ASIC
- This is a specialized integrated circuit designed to receive and transmit data at gigabit speeds. In this context, it acts as a bridge between the high-speed data coming from the detector pixels and the electronics that process that information. It handles both receiving signals (upstream) and sending signals (downstream).
- Equalization
- Equalization is a technique used to correct signal degradation caused by transmission channels, like cable loss. The ASIC uses structures like CTLE to introduce specific zeros and poles in its transfer function. This compensates for the frequency-dependent losses in the cables, helping to restore the original data quality.
- Peak-to-Peak Jitter
- Jitter refers to the variation in timing of a signal, which can cause errors in data reception. Peak-to-peak jitter measures the total variation between the highest and lowest points of this timing error. Lower peak-to-peak jitter indicates a cleaner, more reliable signal that is better suited for high-precision detector readout.
- Radiation Tolerance
- This describes how well the ASIC can function when exposed to radiation, such as gamma rays from a Co-60 source. The paper tested GBCR1 and found it could withstand a total ionizing dose of 200 kGy without significant performance degradation, which is crucial for operating inside large particle detectors like ATLAS.
Terminology
Summary
We present two prototypes of a gigabit transceiver ASIC, GBCR1 and GBCR2, both designed in a 65-nm CMOS technology for the ATLAS Inner Tracker Pixel Detector readout upgrade<ref:2008. p. 009738#pg2> The single most informative sentence about the paper's subject and finding is: We present two prototypes of a gigabit transceiver ASIC, GBCR1 and GBCR2, both designed in a 65-nm CMOS technology for the ATLAS Inner Tracker Pixel Detector readout upgrade<ref:2008.09738#pg2>.
Prototype Descriptions
GBCR1 has four upstream receiver channels and one downstream transmitter channel with pre-emphasis<ref:2008.09738#pg2> Each upstream channel receives the data at 5. p. 012 Gbps through a 5 meter AWG34 Twinax cable from an ASIC driver located on the pixel module and restores the signal from the high frequency loss due to the low mass cable<ref:2008. p. 009738#pg2> The downstream driver is designed to transmit the 2. p. 056 Gbps signal from lpGBT to the electronics on the pixel module over the same cable<ref:2008. p. 009738#pg2> GBCR2 has seven upstream channels and two downstream channels<ref:2008. p. 009738#pg2> Each upstream channel works at 1. p. 028 Gbps to recover the data directly from the RD53B ASIC through a 1 meter custom FLEX cable followed by a 6 meter AWG34 Twinax cable<ref:2008. p. 009738#pg2> The downstream is designed to transmit the 160 Mbps signal from lpGBT through the same cable connection to RD53B and the jitter is about 157 ps at the cable ends<ref:2008. p. 009738#pg2>.
Equalization Techniques
The equalizer used in GBCR1 is based on a CTLE structure<ref:2008.09738#pg2> The passive resistor and capacitor create a zero and a pole in the transfer function to compensate for channel loss<ref:2008. p. 109738#pg2> The equalization strength is determined by the ratio of the zero and the pole, as described in formula 3, EqualizationS trength = ωZ / ωp1 = 1 + RSCS squared (3)<ref:2008. p. 109738#pg2> In GBCR2, a three-stage structure of CTLE is adopted to compensate with 3 order zero for high frequency range<ref:2008. p. 409738#pg2> For the medium and low frequency parts, each of them just employs one CTLE stage to recover the signal loss in their range respectively<ref:2008. p. 409738#pg2> The entire equalizer stage can provide 30 dB peaking strength at most<ref:2008. p. 409738#pg2>.
Performance Metrics and Testing
The peak-peak jitter (throughout the paper jitter is always peak-peak unless specified) of the restored signal is 35.4 ps at the output of GBCR1, and 138 ps for the downstream channel at the cable ends<ref:2008. p. 009738#pg2> When the CDR is off and the retiming is bypassed, the peak-peak jitter is 79 ps and the random jitter is 4. p. 23 ps (RMS) under the resistance setting of 0 and the capacitance setting of 3 of the equalizers<ref:2008. p. 309738#pg2> When the CDR is turned on, the retiming circuit reduces the peak-peak jitter to 35 ps and the random jitter 1. p. 35 ps (RMS)<ref:2008. p. 009738#pg2> The total power consumption of GBCR1 is 192 mW<ref:2008. p. 509738#pg2>.
Radiation Tolerance
GBCR1 has also been irradiated with gamma from a Co-60 source<ref:2008.09738#pg2> It survives the total ionizing dose up to 200 kGy which is the maximum required dose<ref:2008. p. 309738#pg2> The jitter of upstream channel changed no more than 2 ps after the radiation in both cases of CDR on and off<ref:2008. p. 309738#pg2>.
Downlink Channel Optimization
The GBCR2 downlink channel is optimized for 160 Mbps data rate and suppresses the ISI jitter for the transmission in the cables<ref:2008.09738#pg2> Even in the transmission situation with the longest cables, the downstream channel significantly reduce the ISI jitter from 500 ps to 157 ps<ref:2008. p. 509738#pg2> The output signal jitter is to 70 ps, which meets the requirement of the eRx in lpGBT<ref:2008. p. 6 p. 6 p. 609738#pg2>.
Summary Table
Table 1 shows that for GBCR2 in Equalizer mode, where the retiming circuit and phase shifter are off to save the power, the total power consumption is 79 mW<ref:2008.09738#pg2> In the retiming mode, the power consumption increases to 105 mW but ISI jitter is further suppressed<ref:2008. p. 509738#pg2> The downlink channel is optimized for 160 Mbps data rate and suppresses the ISI jitter for the transmission in the cables<ref:2008. p. 6 p. 609738#pg2>. The output signal jitter is to 70 ps, which meets the requirement of the eRx in lpGBT<ref:2008.09738#pg2>. The downlink channel is optimized for 160 Mbps data rate and suppresses the ISI jitter for the transmission in the cables<ref:2008.09738#pg2>. The output signal jitter is to 70 ps, which meets the requirement of the eRx in lpGBT<ref:2008.09738#pg2>.
Conclusion
Based on simulation GBCR2 will work well to receive and transmit the specific data by the uplink and downlink channels<ref:2008.09738#pg2> The chip survives the total ionizing dose of 200 kGy with a gamma source<ref:2008. p. 509738#pg2>. We expect to test GBCR2 soon<ref:2008. p. 609738#pg2>.
Acknowledgments
This work was supported by the US-ATLAS phase-2 upgrade grant administrated by the US-ATLAS phase2 upgrade project office and the Office of High Energy Physics of the U.S. Department of Energy under contract DE-AC02-05CH11231<ref:2008. p. 609738#pg2> The authors would like to be grateful to Andrew Young and Dong Su from SLAC, Maurice Garcia-Sciveres and Veronica Wallangen from LBNL, James Kierstead from BNL for their kind help on the test of GBCR1<ref:2008. p. 609738#pg2>.
Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.
Improvements for AI systems
-
Improve data recovery in high-loss cable environments by implementing a Continuous Time Linear Equalizer (CTLE) with programmable RS and CS values to adjust zero and pole positions for optimal results in different situations. This allows the system to compensate for signal loss up to 30 dB at most, as shown in the GBCR2 design.
-
Enhance timing accuracy by using a Clock Data Recovery (CDR) adapted from lpGBT for retiming, which reduces peak-peak jitter from 79 ps when off to 35 ps when on in GBCR1 testing. This results in a significant reduction of timing uncertainty critical for precise detector readout.
-
Increase power efficiency by removing the CDR module in GBCR2 and using an external clock with a shared phase shifter for retiming, resulting in a total power consumption of 79 mW in equalizer mode compared to 105 mW when the retiming circuit is on. This lower power profile is essential for meeting tight radiation-tolerant power budgets.
-
Improve DC offset management by employing a DC offset cancellation circuit in GBCR2 that amplifies and feeds back the offset to adjust and cancel it, achieving a low cut-off frequency of 115 kHz with high feedback gain to suppress DC offsets. This ensures the data encoded in the 64b/66b line code is not affected by static errors.
-
Optimize downlink performance by redesigning the pre-emphasizer stage for GBCR2, setting its zero at 40 MHz and pole at 120 MHz, with a control of up to 3 bits to adjust peaking strength up to 14.8 dB. This optimization significantly reduces ISI jitter from 500 ps down to approximately 157 ps for the downlink channel transmission over long cables.
Related papers
- Cryogenic Mechanical Loss of GaAs/AlGaAs Crystalline Coatings
- The physical design of the superfluid helium-4 UCN source at CSNS
- A new diffuse reflector filament for additive manufacturing of 3D printing finely-segmented plastic scintillator
- Characterization of CRYO ASIC for charge readout in the nEXO experiment
- Reconstructing High-Fidelity Light Yield Maps for Surface LArTPCs Using Crossing Cosmic Muons
- OASIS-ERIS: Open Acquisition System for IEPE Sensors - Electrically Refined and Inter-device Synchronization