A new diffuse reflector filament for additive manufacturing of 3D printing finely-segmented plastic scintillator
Listen
Radio episode about this paper
Transcript
Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.
Kai: I'm Kai.
Mira: And I'm Mira, here with Lev.
Kai: We're looking at the paper: "A new diffuse reflector filament for additive manufacturing of 3D printing finely-segmented plastic scintillator".
Mira: Here's the gist of the paper. This study presents the development and characterization of novel white reflective filaments suitable for additive manufacturing of finely segmented plastic scintillators <ref:2604.26033#pg2> because these new filaments demonstrate improved optical properties leading to a lower light crosstalk and a higher light yield compared to previous works <ref:2604.26033#pg2>.
Kai: Development of Reflective Filament Formulations The research involved developing white reflective filaments based on polycarbonate (PC) and polymethyl methacrylate (PMMA) polymers, loaded with titanium dioxide (TiO2) and polytetrafluoroethylene (PTFE) to enhance reflectivity <ref:2604.26033#pg2>.
Mira: Reflective filaments were fabricated by thermally extruding polymer-additive mixtures using both laboratory and industrial-scale equipment <ref:2604.26033#pg2>.
Kai: Polymer granules (PC or PMMA) were first mixed with reflective additive powders, specifically TiO2 and PTFE, in a batch mixer to ensure uniform distribution <ref:2604.26033#pg2>.
Title and authors: Kai: Moving on, the paper title is "A new diffuse reflector filament for additive manufacturing of finely segmented plastic scintillator," which basically tells us they are proposing a new way to make white reflective filaments for these detectors using three dee printing <ref:2604.26033#pg1,A new diffuse reflector filament for additive manufacturing of>.
Mira: It’s about finding a material that works well with the additive manufacturing process, specifically FDM, because they showed that FDM doesn't degrade the optical performance of standard polystyrene based scintillators.
Lev: They are looking at overcoming the issue where you have to mix materials during simultaneous printing, which was a problem with polystyrene and PST-based reflectors before.
Kai: The paper explains that they demonstrated filaments composed of polystyrene and polymethyl methacrylate blended with titanium dioxide could serve as effective reflective components for this kind of application.
Mira: They also showed that an inorganic scintillator can be obtained by embedding inorganic granules into a polymer matrix and using it for three dee printing, which is a way to get the reflector material in there <ref:2604.26033#pg1>.
Lev: The main thing they are doing here is automating the fabrication of finely segmented detectors by allowing you to print both the scintillator and reflective materials at the same time using two extruders.
Kai: It’s about moving away from manual assembly toward an automated way of building these complex, finely segmented structures.
Mira: The implication for us is that this opens up a new path for creating detectors where you don't have to rely on traditional, less precise fabrication methods for the reflective parts.
Lev: It suggests a much more integrated manufacturing process for these detectors because you can control the material mixing during the build itself.
Kai: So, we’ve seen they are proposing a new filament formulation that addresses both the material compatibility and the need for high reflectivity in this new additive manufacturing context.
The paper's summary: Mira: They summarize their work by showing how they developed and characterized these novel white reflective filaments based on polycarbonate and polymethyl methacrylate polymers loaded with titanium dioxide and polytetrafluoroethylene to enhance reflectivity.
Kai: They detail the process, which involves first mixing the polymer granules, like PC or PMMA, with the reflective additive powders, specifically TiO2 and PTFE in a batch mixer to make sure everything is distributed uniformly.
Lev: The characterization of those additive powders itself was important because they measured their pure optical performance before putting them into any polymer matrices at all.
Mira: They found that pure polytetrafluoroethylene showed the highest reflectivity, with measured values exceeding one hundred percent, and titanium dioxide also had good performance at ninety-four point six percent reflectance at four hundred twenty nanometers.
Kai: When they combined the TiO2 and PTFE in a two to one weight ratio, they saw that it didn't actually yield a significant enhancement over using them alone, achieving ninety-four point three percent reflectance at four hundred twenty nanometers.
Mira: Then for the PC based filaments, the formulation with ten percent titanium dioxide and five percent PTFE demonstrated the highest reflectivity among all of the PC based samples in that four hundred ten to four hundred fifty nanometer wavelength range.
Lev: This characterization step was crucial because it determined which specific powder combination actually worked best before they moved on to testing it in a polymer matrix.
Kai: And then they compared the performance of the resulting filaments, showing that PMMA-based samples exhibited both higher reflectivity and higher transmittance compared to PC-based samples overall.
Mira: They specifically noted that at four hundred twenty nanometers, the reflectivity of zero point four millimeter thick PMMA samples reached ninety point five percent, exceeding what was seen in the PC samples.
Lev: But they pointed out that this improved performance came with increased light transmittance being three point seven percent for PMMA versus only zero point six percent for PC at zero point four millimeter thickness.
Kai: And they mentioned that adding PTFE to the PMMA didn't improve things because the PMMA matrix is already very transparent and absorbs less light.
The paper's improvements: Mira: The paper highlights a few improvements over previous work, focusing on the specific formulations they developed for PC and PMMA filaments that maximize reflectivity in their respective polymer systems.
Kai: For the PC based filaments, they found that ten percent titanium dioxide and five percent PTFE was the optimal combination for achieving a reflectivity of eighty-five point five percent at four hundred twenty nanometers.
Lev: That specific formulation is important because it sets a benchmark for what you can expect when designing your reflector material for this application.
Mira: For the PMMA based filaments, they found that fifteen percent of titanium dioxide was enough to achieve even higher reflectivity, reaching ninety-two point zero percent for a zero point two millimeter thickness sample.
Kai: So the improvement lies in finding that specific loading ratio of TiO2 in PMMA for better performance than just mixing it with PTFE.
Lev: The results on the SuperLayer prototype are also noteworthy because it achieved the highest light yield of about thirty-one point two photoelectrons, which outperformed both existing benchmarks.
Mira: Plus, they showed that both PMMA and PC based SuperLayers exhibited excellent optical isolation with a mean of zero point seven percent crosstalk across all channels.
Kai: So the overall improvement is that they’ve found specific loading ratios for each polymer that give you the best combination of reflectivity and light yield and low crosstalk.
Conclusion: Kai: So to wrap up, these results from this paper show that for PC based filaments, the optimal formulation was ten percent titanium dioxide and five percent PTFE, giving a reflectivity of eighty-five point five percent at four hundred twenty nanometers.
Mira: And for PMMA based filaments, fifteen percent of titanium dioxide was sufficient to reach ninety-two point zero percent reflectivity with a zero point two millimeter thickness.
Lev: From my side, I think the most practical implication is that this is the material choice you need to consider when designing your detector components.
Kai: And for the light yield, the SuperLayer built with PMMA achieved about thirty-one point two photoelectrons per million information points per channel, beating both existing prototypes.
Mira: And for crosstalk, they showed that both PMMA and PC based SuperLayers had a mean of zero point seven percent crosstalk across all channels.
Lev: So ultimately, the paper "A new diffuse reflector filament for additive manufacturing of finely segmented plastic scintillator" gives us specific material guidance on what to use when you’re designing these components.
A. Krechਁ, A. Boyarintsevਁ, B. Grynyovਁ, N. Karavaevaਁ, S. Minenko△, T. Sibilieva△, M. Sibilyev△, T. Diemingerb U., Kose B., Li b A., Rubbia b D., Sgalaberna b T., Weber b J. Wülichb, X. Zhao b S.ärnsc, d, e E.Ėillat c, d, e S.Ėugon c, d, e A. De Roeck f
Institute for Scintillation Materials NAS of Ukraine · ETH Zurich · Haute Ecole Spécialisée de Suisse Occidentale · Haute Ecole d’IngĘnie du canton de Vaud · COMATEC-AddiPole
physics.ins-det
Submitted: 2026-04-28
Updated: 2026-10-28
Comments: arXiv admin note: substantial text overlap with arXiv:2509.01247
License: http://creativecommons.org/licenses/by-nc-sa/4.0/
Importance score: 100/100
The gist: This study presents the development and characterization of novel white reflective filaments suitable for additive manufacturing of finely segmented plastic scintillators <ref:2604.26033#pg2> because…
Key concepts
- Reflective Filament Formulations
- This involves mixing polymer granules (PC or PMMA) with reflective powders like titanium dioxide (TiO2) and polytetrafluoroethylene (PTFE). The goal is to create a filament that reflects light efficiently, which is crucial for making plastic scintillators work well in 3D printing.
- Light Crosstalk
- Light crosstalk refers to unwanted light leakage between different segments of the scintillator when it is used in a detector. Lower crosstalk means the detector can clearly distinguish individual signals, leading to better performance and more accurate measurements.
- Light Yield (p.e./MIP/channel)
- Light yield measures how many photoelectrons are generated per Million Incident Photons per channel. A higher light yield indicates that the scintillator is converting incident radiation into a stronger signal, which is essential for detecting low-energy particles effectively.
- Additive Manufacturing (3D Printing)
- This refers to building complex objects layer by layer using 3D printing technology. The study focuses on using these new reflective filaments to create finely segmented plastic scintillators, allowing for precise manufacturing without needing traditional subtractive processes.
Terminology
Summary
This study presents the development and characterization of novel white reflective filaments suitable for additive manufacturing of finely segmented plastic scintillators <ref:2604. p. 0 60, 61072 Kharkiv, Ukraine
𝑏ETH Zurich, Institute for Particle Physics and Astrophysics, CH-8093 Zurich, Switzerland
𝑐Haute Ecole Spécialisée de Suisse Occidentale (HES-SO), Route de Moutier 14, CH-2800 Delémont,
Switzerland
𝑑Haute Ecole d’Ingénierie du canton de Vaud (HEIG-VD), Route de Cheseaux 1, CH-1401 Yverdon-lesBains, Switzerland
𝑒COMATEC-AddiPole, Technopole de Sainte-Croix, Rue du Progrès 31, CH-1450 Sainte-Croix, Switzerland
𝑓 Experimental Physics Department, CERN, Esplanade des Particules 1, 1211 Geneva 23, Switzerland
E-mail: antonkrech@gmail. com
Abstract: This study presents the development and the characterization of novel white reflective
filaments suitable for additive manufacturing of finely segmented plastic scintillators. The results demonstrate the
feasibility of producing compact and modular 3D-printed scintillator detectors with a performance
analogous to standard plastic scintillator detectors. Owing to the improved optical properties of the
new reflector filament, a lower light crosstalk and a higher light yield, compared to past works, is
obtained.Where the paper says it
Where the paper says it
Development of Reflective Filament Formulations
The research involved developing white reflective filaments based on polycarbonate (PC) and polymethyl methacrylate (PMMA) polymers, loaded with titanium dioxide (TiO2) and polytetrafluoroethylene (PTFE) to enhance reflectivity <ref:2604.26033#pg2>. Reflective filaments were fabricated by thermally extruding polymer-additive mixtures using both laboratory and industrial-scale equipment <ref:2604. p. 2 2 Production and characterization of the reflective filaments
2. 1 Production of the reflector filaments
Reflective filaments were fabricated by thermally extruding polymer-additive mixtures using both
laboratory and industrial-scale equipment. 0 [37] were utilized
(see Fig. Polymer granules (PC or PMMA) were first mixed with reflective additive powders,
specifically TiO2 and PTFE, in a batch mixer to ensure uniform distribution. Then, the mixture
was fed into the extruder. The resulting filament had a diameter of 1. The resulting filament had a diameter of 1. 10 mm, suitable for
standard FDM 3D printers.Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Characterization of Additive Powders and Filament Performance
The additive powders were characterized by measuring their pure optical performance before incorporating them into polymer matrices <ref:2604.26033#pg2>. The results showed that pure polytetrafluoroethylene (PTFE) showed the highest reflectivity, with measured values exceeding 100% <ref:2604. p. 3 The reflection value of the reference sample BaSO4 (in the
integrating sphere) was taken as 100%. In the region of scintillation polystyrene luminescence,
the pure polytetrafluoroethylene (PTFE) showed the highest reflectivity, with measured values
exceeding 100%. In the region of scintillation polystyrene luminescence,
the pure polytetrafluoroethylene (PTFE) showed the highest reflectivity, with measured values
exceeding 100%. Titanium dioxide (TiO2) also demonstrated good performance, with a reflectance
of 94. 01247
1Corresponding author. 2Now at the University of Zurich, Switzerland
arXiv:2604. 6% at 420 nm. However, combining TiO2 and PTFE in a 2:1 weight ratio did not yield a
significant enhancement over the individual components, achieving a reflectance of 94. 01247
1Corresponding author. 2Now at the University of Zurich, Switzerland
arXiv:2604. As shown in Fig. 3, the formulation containing 10% TiO2 and
5% PTFE demonstrated the highest reflectivity among all PC-based samples, especially in the
410–450 nm wavelength range.Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Comparison Between Polymer Matrices
The performance of PMMA-based samples exhibited both higher reflectivity and higher transmittance compared to PC-based samples <ref:2604.26033#pg2>. Specifically, at 420 nm, the reflectivity of 0. p. 5 4, PMMA-based samples exhibited both higher reflectivity and higher transmittance compared
to PC-based samples. Specifically, at 420 nm, the reflectivity of 0. Specifically, at 420 nm, the reflectivity of 0. 4 mm thick PMMA samples
reached 90. 4 mm thick PMMA samples
reached 90. 5%, exceeding that of PC samples. 5%, exceeding that of PC samples. However, this came at the cost of increased light
transmittance (3. com
Abstract: This study presents the development and the characterization of novel white reflective
filaments suitable for additive manufacturing of finely segmented plastic scintillators. The filament
is based on polycarbonate (PC) and polymethyl methacrylate (PMMA) polymers loaded with
titanium dioxide (TiO2) and polytetrafluoroethylene (PTFE) to enhance reflectivity. 01247
1Corresponding author. 2Now at the University of Zurich, Switzerland
arXiv:2604. 2 mm thickness. The addition of PTFE
to PMMA did not improve the performance, likely due to the inherently lower light absorption
and higher transparency of the PMMA matrix.Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Detector Prototype Validation
The developed reflector was evaluated in a 3D segmented plastic scintillator prototype called “SuperLayer” <ref:2604.26033#pg2>. The SuperLayer built with the PMMA-based with 10% TiO2 + 5% PTFE reflector achieved the highest light yield, measuring approximately 32 p. p. 9 Complementary measurements were obtained with the 3D printed plastic scintillator prototypes, that are the new SuperLayers and the old SuperCube, exposed to cosmic rays. The SuperLayer
built with the PMMA-based with 10% TiO2 + 5% PTFE reflector achieved the highest light yield,
measuring approximately 32 p. The SiPM analogue signal was carried to
the front-end electronics via micro-coaxial cables. /MIP/channel, compared to the lower 25 p. PMMA with only 15% TiO2
showed a light yield just slightly lower than PMMA-based with 10% TiO2 + 5% PTFE, showing a
slightly different trend compared to the reflectivity measurement, though believed to be within the
experimental uncertainties. On the other hand, both PMMA- and PC-based SuperLayers exhibited
excellent optical isolation, with average cube-to-cube light crosstalk always below 1%. On the other hand, both PMMA- and PC-based SuperLayers exhibited
excellent optical isolation, with average cube-to-cube light crosstalk always below 1%. Overall, our results confirm that the newly developed PMMA-based reflective filaments is
optimal for the 3D printing of finely-segmented plastic scintillator, address the requirements for
high-resolution calorimetry and particle tracking applications and improve both the light yield and
the crosstalk performance of our previous work [34, 35].Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Conclusions and Optimal Materials
The optimal formulation for PC-based filaments consisted of 10% TiO2 + 5% PTFE, yielding a reflectivity of 85.5% at 420 nm and a transmittance as low as 0. p. 9 Optical measurements showed that for PC-based filaments, the optimal formulation consisted
of 10% TiO2 + 5% PTFE, yielding a reflectivity of 85. 5% at 420 nm and a transmittance as low
as 0. 7% for PMMA, whereas
PC maintains a much lower value of 0. On the other hand, the transmittance is reduced to
almost zero for both cases when the thickness of the sample is 1 mm, while the reflectivity of the
PMMA sample remains higher than the PC-based one by 11%. 0 mm thickness sample. For PMMA-based filaments, 15% of TiO2 was sufficient
to achieve even higher reflectivity, reaching 92. 01247
1Corresponding author. 2Now at the University of Zurich, Switzerland
arXiv:2604. Complementary measurements were obtained with the 3D printed plastic scintillator prototypes, that are the new SuperLayers and the old SuperCube, exposed to cosmic rays. The SuperLayer
built with the PMMA-based with 10% TiO2 + 5% PTFE reflector achieved the highest light yield,
measuring approximately 32 p. The SuperLayer
built with the PMMA-based with 10% TiO2 + 5% PTFE reflector achieved the highest light yield,
measuring approximately 32 p. /MIP/channel, outperforming both the PC-based reflector prototype
(25 p. /MIP/channel, outperforming both the PC-based reflector prototype
(25 p. /MIP/channel) and the SuperCube reference detector (29 p. The SiPM analogue signal was carried to
the front-end electronics via micro-coaxial cables. /MIP/channel, compared to the lower 25 p. The peaks at zero correspond to the events where
the crosstalk is below the threshold. Both the prototypes using PMMA- or PC-based reflectors show
low crosstalk, with a mean of 0. 01247
1Corresponding author. 2Now at the University of Zurich, Switzerland
arXiv:2604. On the other hand, both PMMA- and PC-based SuperLayers exhibited
excellent optical isolation, with average cube-to-cube light crosstalk always below 1%. Overall, our results confirm that the newly developed PMMA-based reflective filaments is
optimal for the 3D printing of finely-segmented plastic scintillator, address the requirements for
high-resolution calorimetry and particle tracking applications and improve both the light yield and
the crosstalk performance of our previous work [34, 35].Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
A Contributions
The authors conceptualized, developed and produced the new filament, performed the formal analysis, made the test samples for transmittance and reflectivity tests and performed the measurements <ref:2604.26033#pg2>. T.W. 3D printed the SuperLayer prototypes <ref:2604. p. 9 Complementary measurements were obtained with the 3D printed plastic scintillator prototypes, that are the new SuperLayers and the old SuperCube, exposed to cosmic rays. The SuperLayer
built with the PMMA-based with 10% TiO2 + 5% PTFE reflector achieved the highest light yield,
measuring approximately 32 p. We refer Ref. [34, 35]
for more details about the setup as well as about the pedestal and gain calibration procedure, as the
same experimental setup and methods were used. Finally, we can conclude that both filament compositions provide a better optical performance than
the commercial filament used for the plastic scintillator prototype reported in [34]. 3 Results with the 3D segmented plastic scintillator prototype
We evaluated the performance of the developed reflector in a 3D segmented plastic scintillator
prototype, 3D printed with the fused injection modeling (FIM) technique developed and reported
in Ref.Where the paper says it
Where the paper says it
Where the paper says it
Acknowledgments
This work was supported by the joint grant IZURZ2 224819 of the Swiss National Science Foundation (SNSF) and the National Research Foundation of Ukraine (NRFU) <ref:2604.26033#pg2>. This work was also supported by the SNSF grant PCEFP2 203261 <ref:2604. p. 9 Acknowledgments
This work was supported by the joint grant IZURZ2_224819 of the Swiss National Science Foundation (SNSF) and the National Research Foundation of Ukraine (NRFU). This work was also
supported by the SNSF grant PCEFP2_203261.Where the paper says it
Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.
Improvements for AI systems
-
Improve material selection for additive manufacturing by developing a predictive model that correlates polymer choice (PC vs PMMA) and additive loading (TiO2/PTFE concentration) with desired optical properties like reflectivity and transmittance. This system can autonomously suggest the optimal filament composition based on target performance metrics, such as maximizing light yield or minimizing light crosstalk.
-
Enhance 3D printing process optimization by integrating a thermal requirement constraint into the design phase of hollow matrix printing, ensuring the reflector filament
must retain its structural integrity at injection temperatures of about 230C.
This allows the AI to predict potential warping or failure during the FIM process before physical fabrication, reducing material waste and iteration time. -
Develop a high-fidelity simulation environment for light propagation within segmented detectors that incorporates measured optical properties of novel filaments (e.g.,
the optimal formulation consisted of 10% TiO2 + 5% PTFE, yielding a reflectivity of 85.5% at 420 nm
). This system can predict the resultingsingle-channel light yield and cube-to-cube light crosstalk
for any proposed detector geometry before physical prototyping. -
Create an automated data analysis pipeline for cosmic ray exposure that compares
the performance of the old SuperCube, made with the same scintillator filament but a commercial white filament with that of the new SuperLayers made with different custom filaments.
This system can rapidly determine which custom filament formulation yields a higherlight yield MPV
and lower crosstalk based on measured signals. -
Implement a generative design module that uses the successful experimental results to propose novel, optimized geometries for finely segmented detectors, directly addressing the goal of achieving
a good tolerance with manufacturing without any subtractive process.
Abstract
This study presents the development and the characterisation of a novel white, reflective filament suitable for additive manufacturing of finelysegmented plastic scintillators. The filament is based on polycarbonate (PC) and polymethyl methacrylate (PMMA) polymers loaded with titanium dioxide (TiO 2) and polytetrafluoroethylene (PTFE) to enhance reflectivity. A range of filament compositions and thicknesses was evaluated through optical reflection and transmittance measurements of reflective layers made with the Fused Deposition Modelling (FDM) technique. A 3D-segmented plastic scintillator prototype was made with fused injection modelling (FIM) and tested with cosmic-ray muons to assess the light yield and the optical crosstalk. The results of this study demonstrate the feasibility of producing compact, modular 3D-printed scintillator detectors with a performance comparable to that of standard plastic scintillator detectors whilst exhibiting lower light crosstalk and higher light yield, owing to the improved optical properties of the reflector material.
Sources
- A new diffuse reflector filament for additive manufacturing of 3D printing finely-segmented plastic scintillator
- Application of large area SiPMs for the readout of a plastic scintillator based timing detector
- Design, Calibration, and Performance of the MINERvA Detector
- A 4pi time-of-flight detector for the ND280/T2K upgrade
- The T2K Fine-Grained Detectors
- The magnetized steel and scintillator calorimeters of the MINOS experiment
- The Electromagnetic Calorimeter for the T2K Near Detector ND280
- A novel segmented-scintillator antineutrino detector
- A fully active fine grained detector with three readout views
- Total Neutron Cross-section Measurement on CH with a Novel 3D-projection Scintillator Detector
- Neutron detection and application with a novel 3D-projection scintillator tracker in the future long-baseline neutrino oscillation experiments
- The Super Fine-Grained Detector for the T2K neutrino oscillation experiment
- A novel polystyrene-based scintillator production process involving additive manufacturing
- Demonstrating a single-block 3D-segmented plastic-scintillator detector
- Additive manufacturing of inorganic scintillator-based particle detectors
- Beam test results of a fully 3D-printed plastic scintillator particle detector prototype
Related papers
- Cryogenic Mechanical Loss of GaAs/AlGaAs Crystalline Coatings
- The physical design of the superfluid helium-4 UCN source at CSNS
- Characterization of CRYO ASIC for charge readout in the nEXO experiment
- Reconstructing High-Fidelity Light Yield Maps for Surface LArTPCs Using Crossing Cosmic Muons
- OASIS-ERIS: Open Acquisition System for IEPE Sensors - Electrically Refined and Inter-device Synchronization
- Low-energy nuclear recoil calibration of the LUX-ZEPLIN experiment with a photoneutron source