OASIS-ERIS: Open Acquisition System for IEPE Sensors - Electrically Refined and Inter-device Synchronization

arXiv:2607.22061 · physics.ins-det · Submitted 2026-07-24 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: I'm Kai.

Mira: And I'm Mira, here with Lev.

Kai: We're looking at the paper: "OASIS-ERIS: Open Acquisition System for IEPE Sensors - Electrically Refined and Inter-device Synchronization".

Mira: Here's the gist of the paper. OASIS-ERIS introduces an Open Acquisition System for IEPE Sensors that enhances laboratory usability through inter-device synchronization and increases achievable sampling frequency to 100 kHz because it closely matches commercial system performance in Experimental Modal Analysis while offering a low-cost, open-source alternative.

Kai: Hardware Description The OASIS-ERIS board utilizes an Analog Devices AD7606C-18 analog-to-digital converter providing 18-bit resolution on eight simultaneously sampled channels and is controlled by the Espressif ESP32-S3 microcontroller.

Mira: Key hardware features include an Improved Boost Converter based on the Texas Instruments LM5157 for a 24 V IEPE supply and a Simplified IEPE Front-End using Texas Instruments LM334M constant current sources.

Kai: The board incorporates internal USB Connector embedding into Linux ecosystems, an Improved WiFi Interface with a refined on-board antenna, and a Local Sample Cache allowing for fully autonomous device operation.

Paper summary: Kai: So, we're looking at this paper, "OASIS-ERIS: Open Acquisition System for IEPE Sensors - Electrically Refined and Inter-device Synchronization." It's about taking an existing setup and making it better with synchronization between different sensors.

Mira: Exactly. The main idea here is that they developed this new system to improve how we use IEPE sensors in the lab by getting them all to work together in a truly synchronized way. They claim this open acquisition system, OASIS-ERIS, can increase the sampling frequency up to one hundred kHz because they switched the firmware implementation <ref:2607.22061#pg1>.

Lev: From an error correction standpoint, that jump to one hundred kHz is significant when you think about real hardware overhead <ref:2607.22061#pg1>. We need to see how much that increased speed actually impacts the stability of our modal parameters, especially when we're dealing with structural dynamics.

Kai: Right, so it’s not just about speed; they built this board using the Analog Devices AD7606C-eighteen analog-to-digital converter with eighteen bits of resolution on eight channels, controlled by an ESP32 S3 microcontroller <ref:2607.22061#pg1,the Analog Devices AD7606C-18 analog-to-digital converter>. They also swapped out some parts for a better boost converter and a simplified front-end using Texas Instruments LM334M constant current sources.

Mira: And the real focus of this paper seems to be that inter-device synchronization feature. They physically connect the sample clocks across devices using BNC connectors so they can achieve truly synchronized data acquisition with an arbitrary number of boards.

Lev: That physical connection mechanism sounds like it would introduce some complexity in a real deployment, but if it works, it’s a way to get high-fidelity results from multiple sensors simultaneously without relying on software timing alone.

Kai: The validation tests they did showed that this synchronization test resulted in a maximum sample offset of one sample or ten microseconds for normal sampling. Plus, when they compared it against a commercial measurement system in Experimental Modal Analysis, OASIS-ERIS closely matched the performance for frequency response function estimation if the signal level is sufficiently high.

Mira: So, they're saying that even with this open-source approach and the new synchronization method, you can get results that are comparable to what you'd see on a commercial system when your signal is strong enough.

Lev: But I wonder about the assumptions behind matching performance; does it hold up if we push the signal level down, or if we have more than just two boards synchronized?

Kai: They also detailed the software stack evolution, moving from Arduino ESP32 to a direct C++ implementation using ESP-IDF for faster hardware access and those higher sample rates. They have several components there, including a Python API called OASIS-API that handles serial communication and structured HDF5 data storage.

Paper summary: Mira: And they have the OASIS-TUI, which is this guided terminal user interface optimized for remote operation via SSH, and then the OASIS-GUI for classical lab use. It seems they've covered the whole spectrum from remote control to traditional lab setup.

Lev: I’m interested in that Python API part because that’s where you actually have to write the code to handle all those structured data saves, like HDF5, and see how much overhead that adds on top of the hardware processing speed they're promising.

Kai: And for data storage, stored acquisition files are saved on an exFAT SD card using commands like ACQ:SAMPLE and meta files are also saved there. Stored measurement transfer over CDC serial is disabled; you have to get the data out through USB MSC instead.

Mira: That’s a specific detail about the file system interaction, which is important because it dictates how easily you can retrieve those long acquisition records for analysis later on.

Lev: So, what’s the real limitation here from an engineering standpoint? I want to know where this setup struggles when you try to run it on actual hardware versus in a simulated environment.

Kai: The paper points out that the bill of materials cost is about one hundred forty to one hundred sixty euros, which makes it very accessible for projects with tight budgets compared to proprietary systems. They also provided design files in the Zenodo repository including KiCad project and manufacturing files, which speaks to their commitment to openness.

Mira: The paper emphasizes the open-source aspects of this work, mentioning Openness, Freedom, Flexibility and Customization as key benefits for anyone who wants to audit the source code and modify it.

Lev: Auditing is one thing; running it on real hardware with that specific synchronization setup is another. I need to know how much of the complexity lands on the user interface side versus needing custom drivers for their specific IEPE sensor setup.

Kai: They did confirm that they can trigger acquisition by any acquire command where a master board broadcasts the acquisition duration, sampling rate, and filename base over GPIO13 one-wire to listening boards.

Mira: That distributed one-Wire Acquisition sounds like it solves the problem of getting multiple boards to start and stop at exactly the same time, which is a major usability win for complex modal testing <ref:2607.22061#pg1>.

Lev: If the master board broadcasts parameters over one wire, that’s a relatively simple communication protocol, which is good for robustness on hardware. But how reliable is that one-wire broadcast across different physical setups?

Paper summary: Kai: The experimental validation summary confirms that inter-device synchronization with a maximum offset of one sample or ten microseconds was possible, and for triggered sampling, all boards are always perfectly synchronized.

Mira: That perfect synchronization result is what really validates their core claim about the inter-device feature; they showed that even with this method working, the cross-correlation analysis showed that the maximum sample offset across all boards and tests was one for normal sampling at a sample rate of one hundred kHz <ref:2607.22061#pg1>.

Lev: One sample offset is tight for high-speed acquisition; that tells me how much timing jitter we are dealing with when we try to run this on a real system, and it’s a good number to target in our hardware design.

Kai: When comparing the modal identification results against the commercial system, they found barely any difference in identified eigenfrequencies between OASIS-ERIS and the commercial system. They also noted that the exact match of the identified mode shapes indicates that inter-device synchronization is successful, requiring responses from all sensors connected to different OASIS-ERIS boards.

Mira: So, it’s not just matching the frequency; it’s matching the actual shape of the structural response when you link all those boards together, which is a deeper level of validation than just a frequency plot.

Lev: That means if we use this system, we can trust that the modal parameters derived from our data are consistent across all sensors involved in the experiment, provided they’re all linked correctly.

Kai: The paper concludes by presenting OASIS-ERIS as a viable replacement for projects with tightly constrained budgets because of its open-source license and its ability to closely match commercial performance. They highlight the benefits of using this system for day-to-day lab use.

Mira: The implication is that we don't have to commit to expensive proprietary systems just to get high sampling rates and synchronized data acquisition for our structural dynamic applications.

Lev: It’s a solid piece of open hardware, but the caveat remains that it depends heavily on the user setting up the physical synchronization correctly, which is a manual assembly task they mentioned requiring BNC and SMB connectors.

Kai: So, to wrap up this paper on "OASIS-ERIS: Open Acquisition System for IEPE Sensors - Electrically Refined and Inter-device Synchronization," it’s an open system that aims to bridge the gap between commercial performance and accessible, open hardware for structural analysis.

Mira: It shows that with the right synchronization mechanism, you can achieve high sampling rates like one hundred kHz while keeping the data acquisition process highly flexible and synchronized across multiple devices <ref:2607.22061#pg1>.

Lev: The real challenge we see is making sure that the physical synchronization works reliably in a real-world environment without excessive setup time for each experiment.

Conclusion: Kai: It’s about taking something existing and making it open source so people can actually use it in the lab without paying a fortune for proprietary gear.

Lev: Yeah, the authors are focused on getting high performance—one hundred kilohertz sampling—while keeping the hardware accessible because they use an open license for the code.

Mira: But what does that actually mean for us? It means we can finally get a system that matches commercial results in things like experimental modal analysis without needing to buy a custom, expensive setup from some big vendor.

Kai: It’s about closing the gap between what you can build yourself and what the commercial systems do when the signal is strong enough.

Lev: The real thing is they managed to get this synchronization working physically across different devices using those BNC connectors, which is a big step because software timing alone doesn't always cut it at that speed.

Mira: So, it’s not just about the hardware being cheap; it’s about the method of synchronization allowing all those sensors to actually talk to each other and give you consistent data.

Kai: Exactly. It means for anyone doing structural dynamics research, you can have a system that works reliably without being locked into one specific brand's ecosystem.

Lev: It’s a solid piece of hardware with one hundred sixty euros worth of materials, which is low cost, but the setup still requires manual assembly with those connectors.

Mira: So the takeaway is that this work shows you can get high sampling rates and reliable cross-device synchronization without needing a massive budget or proprietary lock-in.

Kai: It’s a step toward making sophisticated acquisition systems available for regular lab use instead of just being locked away in specialized research facilities.

Lev: And the next thing we need to look at is how much real overhead that physical synchronization adds when you try to run it on actual hardware versus just simulating the timing.

Technical University of Munich

physics.ins-det

Submitted: 2026-07-24

Updated: 2026-08-07

DOI: 10.1016/j.ohx.2026.e00855

Code: https://github.com/ladisk/pyFRF

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 96/100

The gist: OASIS-ERIS introduces an Open Acquisition System for IEPE Sensors that enhances laboratory usability through inter-device synchronization and increases achievable sampling frequency to 100 kHz…

Key concepts

Inter-device Synchronization
This feature physically connects sample clocks between multiple acquisition boards using BNC connectors. A 'Sync Source' broadcasts a hardware clock signal via OneWire, allowing all connected 'Sync Sinks' to acquire data at the exact same time, crucial for accurate modal analysis.
IEPE Sensors
IEPE stands for Integrated Excitation Potentiostat electrodes. These are specialized sensors used in experimental modal analysis to measure mechanical vibrations. OASIS-ERIS is designed specifically to interface with these sensors efficiently.
OASIS-API
This Python API serves as the software bridge, handling all serial communication with the OASIS boards. It manages robust sampling routines and organizes data into structured HDF5 files, making it easy to integrate into existing analysis frameworks.
Frequency Response Function (FRF) Estimation
FRF estimation is a technique used in experimental modal analysis to determine the dynamic characteristics of a structure by measuring how it responds to various inputs. OASIS-ERIS aims to match commercial systems for this estimation when signal levels are high.

Terminology

Summary

OASIS-ERIS introduces an Open Acquisition System for IEPE Sensors that enhances laboratory usability through inter-device synchronization and increases achievable sampling frequency to 100 kHz because it closely matches commercial system performance in Experimental Modal Analysis while offering a low-cost, open-source alternative. p. 0

Where the paper says it

The results show that OASIS-ERIS closely matches the performance of the commercial system, making it a viable replacement for academia and projects with tightly constrained budgets. Keywords Open-Source, Acquisition Hardware, Data Acquisition, Measurement Equipment, Experimental Dynamics, Vibration Analysis Specifications table Hardware name OASIS-ERIS Subject area Educational tools and open-source alternatives to existing commercial tools Hardware type Measuring physical properties and in-lab sensors Closest commercial analog OROS MODS OR10-DAQ-8 or similar compact acquisition systems with 8 IEPE channels and compact form factor Open-source license CC-BY 4.

Hardware Description

The OASIS-ERIS board utilizes an Analog Devices AD7606C-18 analog-to-digital converter providing 18-bit resolution on eight simultaneously sampled channels and is controlled by the Espressif ESP32-S3 microcontroller. Key hardware features include an Improved Boost Converter based on the Texas Instruments LM5157 for a 24 V IEPE supply and a Simplified IEPE Front-End using Texas Instruments LM334M constant current sources. p. 2

Where the paper says it

In the following, the hardware and software features, as well as the new inter-device synchronization, are described in detail. Internal USB Connector • Enables embedding into Linux ecosystems • Allows for compact and modular integration Analog-Digital Converter • Analog Devices AD7606C-18 • Eight simultaneously sampled channels with adjustable voltage ranges and oversampling Improved Boost Converter • 24 V IEPE supply based on Texas Instruments LM5157 • More compact design without through-hole components Simplified IEPE Front-End • Texas Instruments LM334M constant current sources • High-pass filter with cut-off frequency of 0.

The board incorporates internal USB Connector embedding into Linux ecosystems, an Improved WiFi Interface with a refined on-board antenna, and a Local Sample Cache allowing for fully autonomous device operation. p. 2
Where the paper says it

Internal USB Connector • Enables embedding into Linux ecosystems • Allows for compact and modular integration Analog-Digital Converter • Analog Devices AD7606C-18 • Eight simultaneously sampled channels with adjustable voltage ranges and oversampling Improved Boost Converter • 24 V IEPE supply based on Texas Instruments LM5157 • More compact design without through-hole components Simplified IEPE Front-End • Texas Instruments LM334M constant current sources • High-pass filter with cut-off frequency of 0. 8 Hz at 3 dB Redesigned Connectors • Switch to SMB connectors • Significant weight reduction compared to previous version • Easier connection of sensors Versatile Mounting Options • M3 mounting holes in 90x90 mm grid • Allows secure attachment to devices • Vertical stacking for laboratory use Micro-Controller • Espressif ESP32-S3 chip • Hardware-generated PWM signal for robust sampling • C++ Firmware (ESP-IDF) Local Sample Cache • Samples are stored locally on each device’s SD card • Allows a fully autonomous device operation Inter-Device Synchronization • Connection through BNC • Connects the master sample clock to attached devices • Broadcasting of data acquisition settings via OneWire Synchronized Sampling 1) Master announces upcoming sample and the parameters 2) Connected devices prepare data acquisition 3) Master clock triggers samples of all devices at the ADC level 4) Samples are post-processed by each device independently Improved WiFi Interface • Refined on-board antenna • Connection of external antennas through an U.

Software Stack Evolution

The firmware has undergone significant changes with a migration from the Arduino ESP32 framework to a direct C++ implementation using the ESP-IDF to enable faster hardware access and higher sample rates. The software stack includes several components:

  1. Custom Scripting, which allows for full integration in existing frameworks using Python scripting. p. 3

    Where the paper says it

    An overview of the current software stack is shown in fig. Custom Scripting • Full integration in existing frameworks using Python scripting • High level of hardware control OASIS-TUI • Guided terminal user interface • Optimized for remote operation, e.

  2. OASIS-TUI, a Guided terminal user interface optimized for remote operation via SSH. p. 3

    Where the paper says it

    Custom Scripting • Full integration in existing frameworks using Python scripting • High level of hardware control OASIS-TUI • Guided terminal user interface • Optimized for remote operation, e. , using SSH Python API (OASIS-API) • Fully handles serial communication with devices • Provides robust and tested sampling routines • Ready-to-use structured HDF5 data storage OASIS-GUI • Complete graphical user interface • Easy-to-use solution intended for classical lab use Serial Communication (Virtual COM Port) C++ Device Firmware (ESP-IDF) • Open-Source and fully customizable • Low-level control of sampling hardware • Robust sampling procedure using SD card caching Figure 3: Overview of the current OASIS software stack.

  3. Python API (OASIS-API), which fully handles serial communication with devices and provides robust sampling routines and structured HDF5 data storage. p. 3

    Where the paper says it

    Custom Scripting • Full integration in existing frameworks using Python scripting • High level of hardware control OASIS-TUI • Guided terminal user interface • Optimized for remote operation, e. , using SSH Python API (OASIS-API) • Fully handles serial communication with devices • Provides robust and tested sampling routines • Ready-to-use structured HDF5 data storage OASIS-GUI • Complete graphical user interface • Easy-to-use solution intended for classical lab use Serial Communication (Virtual COM Port) C++ Device Firmware (ESP-IDF) • Open-Source and fully customizable • Low-level control of sampling hardware • Robust sampling procedure using SD card caching Figure 3: Overview of the current OASIS software stack.

  4. OASIS-GUI, a complete graphical user interface intended for classical lab use. p. 3

    Where the paper says it

    Custom Scripting • Full integration in existing frameworks using Python scripting • High level of hardware control OASIS-TUI • Guided terminal user interface • Optimized for remote operation, e. , using SSH Python API (OASIS-API) • Fully handles serial communication with devices • Provides robust and tested sampling routines • Ready-to-use structured HDF5 data storage OASIS-GUI • Complete graphical user interface • Easy-to-use solution intended for classical lab use Serial Communication (Virtual COM Port) C++ Device Firmware (ESP-IDF) • Open-Source and fully customizable • Low-level control of sampling hardware • Robust sampling procedure using SD card caching Figure 3: Overview of the current OASIS software stack.

Inter-Device Synchronization Mechanism

The flagship feature is the added inter-device synchronization which achieves truly synchronized data acquisition by physically connecting the sample clocks across devices via BNC connectors. The working principle involves a Sync Source device communicating sample parameters via OneWire and broadcasting a hardware-generated PWM sample clock to all Sync Sinks. p. 2

Where the paper says it

Internal USB Connector • Enables embedding into Linux ecosystems • Allows for compact and modular integration Analog-Digital Converter • Analog Devices AD7606C-18 • Eight simultaneously sampled channels with adjustable voltage ranges and oversampling Improved Boost Converter • 24 V IEPE supply based on Texas Instruments LM5157 • More compact design without through-hole components Simplified IEPE Front-End • Texas Instruments LM334M constant current sources • High-pass filter with cut-off frequency of 0. 8 Hz at 3 dB Redesigned Connectors • Switch to SMB connectors • Significant weight reduction compared to previous version • Easier connection of sensors Versatile Mounting Options • M3 mounting holes in 90x90 mm grid • Allows secure attachment to devices • Vertical stacking for laboratory use Micro-Controller • Espressif ESP32-S3 chip • Hardware-generated PWM signal for robust sampling • C++ Firmware (ESP-IDF) Local Sample Cache • Samples are stored locally on each device’s SD card • Allows a fully autonomous device operation Inter-Device Synchronization • Connection through BNC • Connects the master sample clock to attached devices • Broadcasting of data acquisition settings via OneWire Synchronized Sampling 1) Master announces upcoming sample and the parameters 2) Connected devices prepare data acquisition 3) Master clock triggers samples of all devices at the ADC level 4) Samples are post-processed by each device independently Improved WiFi Interface • Refined on-board antenna • Connection of external antennas through an U.

This synchronization allows for arbitrary numbers of acquisition boards to be synchronized together. p. 0
Where the paper says it

By physically connecting the sample clocks across devices, a truly synchronized data acquisition can be achieved with an arbitrary number of acquisition boards. Additionally, a migration of the firmware to ESP-IDF allows a major increase of the achievable sampling frequency to 100 kHz.

Performance Validation Results

Validation tests confirmed the system's capabilities, showing that the inter-device synchronization test resulted in a maximum sample offset of one sample or 10 µs for normal sampling. Furthermore, when compared against a commercial measurement system in Experimental Modal Analysis, OASIS-ERIS closely matches performance for Frequency Response Function estimation provided the signal level is sufficiently high. p. 0

Where the paper says it

Further, the performance of OASIS-ERIS is tested against a commercial measurement system in an Experimental Modal Analysis campaign. The results show that OASIS-ERIS closely matches the performance of the commercial system, making it a viable replacement for academia and projects with tightly constrained budgets.

The structural dynamic validation showed that no meaningful differences were observed in identified modal parameters between OASIS-ERIS and the commercial system. p. 0
Where the paper says it

This paper documents the hardware and software stack of OASIS-ERIS, and provides all materials necessary for reproduction. Further, the performance of OASIS-ERIS is tested against a commercial measurement system in an Experimental Modal Analysis campaign.

Design and Build Details

The hardware design summary indicates that the bill of materials cost is approximately 160 to 140 euros. Manual assembly is required for components such as the BNC and SMB connectors, while the PCB manufacturer can assemble most SMD components. p. 8

Where the paper says it

1 Hardware assembly Using the provided KiCad project, or the JLCPCB manufacturing files, the OASIS-ERIS printed circuit board (PCB) can be ordered. It is recommended to let the PCB manufacturer assemble all SMD components of the board; then, only the BNC and SMB connectors, as well as the jumper headers, must be assembled manually.

Housing options include M3 mounting holes in a 90x90 mm grid, and a bottom case can be 3D-printed using an included STL file for isolation. p. 2
Where the paper says it

Internal USB Connector • Enables embedding into Linux ecosystems • Allows for compact and modular integration Analog-Digital Converter • Analog Devices AD7606C-18 • Eight simultaneously sampled channels with adjustable voltage ranges and oversampling Improved Boost Converter • 24 V IEPE supply based on Texas Instruments LM5157 • More compact design without through-hole components Simplified IEPE Front-End • Texas Instruments LM334M constant current sources • High-pass filter with cut-off frequency of 0. 8 Hz at 3 dB Redesigned Connectors • Switch to SMB connectors • Significant weight reduction compared to previous version • Easier connection of sensors Versatile Mounting Options • M3 mounting holes in 90x90 mm grid • Allows secure attachment to devices • Vertical stacking for laboratory use Micro-Controller • Espressif ESP32-S3 chip • Hardware-generated PWM signal for robust sampling • C++ Firmware (ESP-IDF) Local Sample Cache • Samples are stored locally on each device’s SD card • Allows a fully autonomous device operation Inter-Device Synchronization • Connection through BNC • Connects the master sample clock to attached devices • Broadcasting of data acquisition settings via OneWire Synchronized Sampling 1) Master announces upcoming sample and the parameters 2) Connected devices prepare data acquisition 3) Master clock triggers samples of all devices at the ADC level 4) Samples are post-processed by each device independently Improved WiFi Interface • Refined on-board antenna • Connection of external antennas through an U.

The design files are provided in the Zenodo repository including KiCad project and manufacturing files. p. 8
Where the paper says it

The setup of the PC/laptop Python software are covered in section 6. 1 Hardware assembly Using the provided KiCad project, or the JLCPCB manufacturing files, the OASIS-ERIS printed circuit board (PCB) can be ordered.

Command Interface Capabilities

Communication with OASIS boards is possible via a serial interface using SCPI or custom commands. The command reference details various operations, including Core Queries like SYST:VERS? to return firmware version and Configuration commands such as CONF:SPARAM? p. 6

Where the paper says it

zip This archive contains the Python source code as well as pre-compiled binaries for the OASIS-FactoryFlasher (see also section 5. This program is used for the initial firmware setup and ESP32 configuration of the OASIS board.

to store default sampling parameters. p. 4
Where the paper says it

The working principle is explained below and illustrated in fig. Sync Source OneWire Communication: Sampling Frequency, Sample Length, Filename, Trigger Mode Input Sync Sinks Input Output Device Default Parameters Voltage Ranges: ±2.

Acquisition commands like ACQ:SAMPLE run stored acquisition with device defaults and save files on the exFAT SD card. p. 2
Where the paper says it

Internal USB Connector • Enables embedding into Linux ecosystems • Allows for compact and modular integration Analog-Digital Converter • Analog Devices AD7606C-18 • Eight simultaneously sampled channels with adjustable voltage ranges and oversampling Improved Boost Converter • 24 V IEPE supply based on Texas Instruments LM5157 • More compact design without through-hole components Simplified IEPE Front-End • Texas Instruments LM334M constant current sources • High-pass filter with cut-off frequency of 0. 8 Hz at 3 dB Redesigned Connectors • Switch to SMB connectors • Significant weight reduction compared to previous version • Easier connection of sensors Versatile Mounting Options • M3 mounting holes in 90x90 mm grid • Allows secure attachment to devices • Vertical stacking for laboratory use Micro-Controller • Espressif ESP32-S3 chip • Hardware-generated PWM signal for robust sampling • C++ Firmware (ESP-IDF) Local Sample Cache • Samples are stored locally on each device’s SD card • Allows a fully autonomous device operation Inter-Device Synchronization • Connection through BNC • Connects the master sample clock to attached devices • Broadcasting of data acquisition settings via OneWire Synchronized Sampling 1) Master announces upcoming sample and the parameters 2) Connected devices prepare data acquisition 3) Master clock triggers samples of all devices at the ADC level 4) Samples are post-processed by each device independently Improved WiFi Interface • Refined on-board antenna • Connection of external antennas through an U.

The TCP subset supports advanced acquisition commands including duration s, sample rate hz, trigger level v, sync mode, v1 through v8, and oversampling. p. 5
Where the paper says it

This communication contains the sampling frequency, the sample length, a unique filename for storage, and the trigger mode, i. , whether a level trigger on the Sync Source is used to start the sample.

The legacy serial commands remain available for compatibility with existing clients. p. 3
Where the paper says it

Custom Scripting • Full integration in existing frameworks using Python scripting • High level of hardware control OASIS-TUI • Guided terminal user interface • Optimized for remote operation, e. , using SSH Python API (OASIS-API) • Fully handles serial communication with devices • Provides robust and tested sampling routines • Ready-to-use structured HDF5 data storage OASIS-GUI • Complete graphical user interface • Easy-to-use solution intended for classical lab use Serial Communication (Virtual COM Port) C++ Device Firmware (ESP-IDF) • Open-Source and fully customizable • Low-level control of sampling hardware • Robust sampling procedure using SD card caching Figure 3: Overview of the current OASIS software stack.

Version Control and Release Rules

The release and storage rules stipulate that the current major release line is 4, and major and minor releases must match for firmware, oasis-api, oasis-tui, and oasis-gui. Stored acquisition files are retrieved from the USB MSC volume rather than transferred over CDC serial. p. 4

Where the paper says it

Then, the Sync Source transmits the hardwaregenerated PWM sample clock to all Sync Sink devices. Samples are stored locally on each device and can be transferred through the USB-C port, for example, fully automatically with the provided Python API.

Firmware updates for boards already running OASIS firmware use firmware. p. 3
Where the paper says it

Custom Scripting • Full integration in existing frameworks using Python scripting • High level of hardware control OASIS-TUI • Guided terminal user interface • Optimized for remote operation, e. , using SSH Python API (OASIS-API) • Fully handles serial communication with devices • Provides robust and tested sampling routines • Ready-to-use structured HDF5 data storage OASIS-GUI • Complete graphical user interface • Easy-to-use solution intended for classical lab use Serial Communication (Virtual COM Port) C++ Device Firmware (ESP-IDF) • Open-Source and fully customizable • Low-level control of sampling hardware • Robust sampling procedure using SD card caching Figure 3: Overview of the current OASIS software stack.

bin copied to the MSC volume, and the board applies the update and reboots automatically. p. 5
Where the paper says it

At this point, the acquired data is stored on the SD card of each OASIS-ERIS board. When all boards are connected to the same PC/laptop, the provided Python software will automatically download data from the boards and combine it into a single file.

The protocol version is currently PV1 with CRC16-CCITT-FALSE as the CRC algorithm. p. 1
Where the paper says it

, on drones or race cars. The open acquisition system described in this article, OASIS-ERIS (Open Acquisition System for IEPE Sensors - Electrically Refined and Inter-device Synchronization), is the latest version to be released.

The board exposes USB CDC serial at 1,000,000 baud and TCP at Wi-Fi AP at 192. p. 3
Where the paper says it

The key advantage of this is the increased transfer speed of sample data. Instead of relying on the serial connection with speeds of ≈ 1 Mbit/s, a USB 1.

168.4.1, port 5025. p. 3
Where the paper says it

Custom Scripting • Full integration in existing frameworks using Python scripting • High level of hardware control OASIS-TUI • Guided terminal user interface • Optimized for remote operation, e. , using SSH Python API (OASIS-API) • Fully handles serial communication with devices • Provides robust and tested sampling routines • Ready-to-use structured HDF5 data storage OASIS-GUI • Complete graphical user interface • Easy-to-use solution intended for classical lab use Serial Communication (Virtual COM Port) C++ Device Firmware (ESP-IDF) • Open-Source and fully customizable • Low-level control of sampling hardware • Robust sampling procedure using SD card caching Figure 3: Overview of the current OASIS software stack.

The command reference describes the full set of SCPI commands available over USB CDC serial. p. 3
Where the paper says it

Custom Scripting • Full integration in existing frameworks using Python scripting • High level of hardware control OASIS-TUI • Guided terminal user interface • Optimized for remote operation, e. , using SSH Python API (OASIS-API) • Fully handles serial communication with devices • Provides robust and tested sampling routines • Ready-to-use structured HDF5 data storage OASIS-GUI • Complete graphical user interface • Easy-to-use solution intended for classical lab use Serial Communication (Virtual COM Port) C++ Device Firmware (ESP-IDF) • Open-Source and fully customizable • Low-level control of sampling hardware • Robust sampling procedure using SD card caching Figure 3: Overview of the current OASIS software stack.

The board exposes USB MSC mass storage for data retrieval and firmware updates. p. 3
Where the paper says it

This change enables faster, more direct hardware access, resulting in higher sample rates than the previous Arduino-based firmware. It also enables access to features not yet implemented in the Arduino ESP32 framework, most notably the option to expose the on-board micro SD card to a PC/laptop as a mass storage device (USBMSC).

Data Storage and Retrieval

Stored acquisition files are saved on the exFAT SD card using commands like ACQ:SAMPLE, which saves.OASISraw/.OASISmeta files on the exFAT SD card. p. 2

Where the paper says it

Internal USB Connector • Enables embedding into Linux ecosystems • Allows for compact and modular integration Analog-Digital Converter • Analog Devices AD7606C-18 • Eight simultaneously sampled channels with adjustable voltage ranges and oversampling Improved Boost Converter • 24 V IEPE supply based on Texas Instruments LM5157 • More compact design without through-hole components Simplified IEPE Front-End • Texas Instruments LM334M constant current sources • High-pass filter with cut-off frequency of 0. 8 Hz at 3 dB Redesigned Connectors • Switch to SMB connectors • Significant weight reduction compared to previous version • Easier connection of sensors Versatile Mounting Options • M3 mounting holes in 90x90 mm grid • Allows secure attachment to devices • Vertical stacking for laboratory use Micro-Controller • Espressif ESP32-S3 chip • Hardware-generated PWM signal for robust sampling • C++ Firmware (ESP-IDF) Local Sample Cache • Samples are stored locally on each device’s SD card • Allows a fully autonomous device operation Inter-Device Synchronization • Connection through BNC • Connects the master sample clock to attached devices • Broadcasting of data acquisition settings via OneWire Synchronized Sampling 1) Master announces upcoming sample and the parameters 2) Connected devices prepare data acquisition 3) Master clock triggers samples of all devices at the ADC level 4) Samples are post-processed by each device independently Improved WiFi Interface • Refined on-board antenna • Connection of external antennas through an U.

Stored measurement transfer over CDC is disabled, and data must be retrieved through USB MSC. p. 3
Where the paper says it

The key advantage of this is the increased transfer speed of sample data. Instead of relying on the serial connection with speeds of ≈ 1 Mbit/s, a USB 1.

The command STOR allows for deleting matching. p. 0
Where the paper says it

By physically connecting the sample clocks across devices, a truly synchronized data acquisition can be achieved with an arbitrary number of acquisition boards. Additionally, a migration of the firmware to ESP-IDF allows a major increase of the achievable sampling frequency to 100 kHz.

OASISmeta,.OASISraw, and pretrigger raw files from the SD card. p. 2
Where the paper says it

Internal USB Connector • Enables embedding into Linux ecosystems • Allows for compact and modular integration Analog-Digital Converter • Analog Devices AD7606C-18 • Eight simultaneously sampled channels with adjustable voltage ranges and oversampling Improved Boost Converter • 24 V IEPE supply based on Texas Instruments LM5157 • More compact design without through-hole components Simplified IEPE Front-End • Texas Instruments LM334M constant current sources • High-pass filter with cut-off frequency of 0. 8 Hz at 3 dB Redesigned Connectors • Switch to SMB connectors • Significant weight reduction compared to previous version • Easier connection of sensors Versatile Mounting Options • M3 mounting holes in 90x90 mm grid • Allows secure attachment to devices • Vertical stacking for laboratory use Micro-Controller • Espressif ESP32-S3 chip • Hardware-generated PWM signal for robust sampling • C++ Firmware (ESP-IDF) Local Sample Cache • Samples are stored locally on each device’s SD card • Allows a fully autonomous device operation Inter-Device Synchronization • Connection through BNC • Connects the master sample clock to attached devices • Broadcasting of data acquisition settings via OneWire Synchronized Sampling 1) Master announces upcoming sample and the parameters 2) Connected devices prepare data acquisition 3) Master clock triggers samples of all devices at the ADC level 4) Samples are post-processed by each device independently Improved WiFi Interface • Refined on-board antenna • Connection of external antennas through an U.

The board exposes USB CDC serial and USB MSC mass storage as defined in the release rules. p. 3
Where the paper says it

This change enables faster, more direct hardware access, resulting in higher sample rates than the previous Arduino-based firmware. It also enables access to features not yet implemented in the Arduino ESP32 framework, most notably the option to expose the on-board micro SD card to a PC/laptop as a mass storage device (USBMSC).

Synchronization Distribution

Distributed 1-Wire Acquisition allows for triggering by any acquire command, where the master board broadcasts acquisition duration, sampling rate, and filename base over GPIO13 one-wire to listening boards. All listening boards run acquisition while the master CONVST is active and finalize when the external CONVST stream ends. p. 2

Where the paper says it

Internal USB Connector • Enables embedding into Linux ecosystems • Allows for compact and modular integration Analog-Digital Converter • Analog Devices AD7606C-18 • Eight simultaneously sampled channels with adjustable voltage ranges and oversampling Improved Boost Converter • 24 V IEPE supply based on Texas Instruments LM5157 • More compact design without through-hole components Simplified IEPE Front-End • Texas Instruments LM334M constant current sources • High-pass filter with cut-off frequency of 0. 8 Hz at 3 dB Redesigned Connectors • Switch to SMB connectors • Significant weight reduction compared to previous version • Easier connection of sensors Versatile Mounting Options • M3 mounting holes in 90x90 mm grid • Allows secure attachment to devices • Vertical stacking for laboratory use Micro-Controller • Espressif ESP32-S3 chip • Hardware-generated PWM signal for robust sampling • C++ Firmware (ESP-IDF) Local Sample Cache • Samples are stored locally on each device’s SD card • Allows a fully autonomous device operation Inter-Device Synchronization • Connection through BNC • Connects the master sample clock to attached devices • Broadcasting of data acquisition settings via OneWire Synchronized Sampling 1) Master announces upcoming sample and the parameters 2) Connected devices prepare data acquisition 3) Master clock triggers samples of all devices at the ADC level 4) Samples are post-processed by each device independently Improved WiFi Interface • Refined on-board antenna • Connection of external antennas through an U.

Clients use their own locally configured default voltage ranges and oversampling settings. p. 2
Where the paper says it

Internal USB Connector • Enables embedding into Linux ecosystems • Allows for compact and modular integration Analog-Digital Converter • Analog Devices AD7606C-18 • Eight simultaneously sampled channels with adjustable voltage ranges and oversampling Improved Boost Converter • 24 V IEPE supply based on Texas Instruments LM5157 • More compact design without through-hole components Simplified IEPE Front-End • Texas Instruments LM334M constant current sources • High-pass filter with cut-off frequency of 0. 8 Hz at 3 dB Redesigned Connectors • Switch to SMB connectors • Significant weight reduction compared to previous version • Easier connection of sensors Versatile Mounting Options • M3 mounting holes in 90x90 mm grid • Allows secure attachment to devices • Vertical stacking for laboratory use Micro-Controller • Espressif ESP32-S3 chip • Hardware-generated PWM signal for robust sampling • C++ Firmware (ESP-IDF) Local Sample Cache • Samples are stored locally on each device’s SD card • Allows a fully autonomous device operation Inter-Device Synchronization • Connection through BNC • Connects the master sample clock to attached devices • Broadcasting of data acquisition settings via OneWire Synchronized Sampling 1) Master announces upcoming sample and the parameters 2) Connected devices prepare data acquisition 3) Master clock triggers samples of all devices at the ADC level 4) Samples are post-processed by each device independently Improved WiFi Interface • Refined on-board antenna • Connection of external antennas through an U.

If trigger mode is configured on the master, it remains trigger-driven. p. 4
Where the paper says it

The working principle is explained below and illustrated in fig. Sync Source OneWire Communication: Sampling Frequency, Sample Length, Filename, Trigger Mode Input Sync Sinks Input Output Device Default Parameters Voltage Ranges: ±2.

The master broadcasts acquisition parameters over GPIO13 one-wire to listening boards. p. 5
Where the paper says it

By default, all boards are listening for OneWire communications on the EXT SYNC pin. When the sample is triggered, the Sync Source starts transmitting the sample parameters on the EXT SYNC BNC connection to the connected boards, the Sync Sinks, using OneWire.

The master remains trigger-driven when a trigger mode is configured on the master. p. 4
Where the paper says it

The working principle is explained below and illustrated in fig. Sync Source OneWire Communication: Sampling Frequency, Sample Length, Filename, Trigger Mode Input Sync Sinks Input Output Device Default Parameters Voltage Ranges: ±2.

Experimental Validation Summary

The signal generator synchronicity test demonstrated that inter-device synchronization with a maximum offset of one sample or 10 µs is possible. The cross-correlation analysis showed that the maximum sample offset across all boards and tests was 1 for normal sampling at a sample rate of 100 kHz. p. 0

Where the paper says it

By physically connecting the sample clocks across devices, a truly synchronized data acquisition can be achieved with an arbitrary number of acquisition boards. Additionally, a migration of the firmware to ESP-IDF allows a major increase of the achievable sampling frequency to 100 kHz.

For triggered sampling, all boards are always perfectly synchronized. p. 5
Where the paper says it

When the sample is triggered, the Sync Source starts transmitting the sample parameters on the EXT SYNC BNC connection to the connected boards, the Sync Sinks, using OneWire. This communication contains the sampling frequency, the sample length, a unique filename for storage, and the trigger mode, i.

The performance comparison showed that OASIS-ERIS can match the commercial system for FRF estimation if the signal level is sufficiently high. p. 0
Where the paper says it

This paper documents the hardware and software stack of OASIS-ERIS, and provides all materials necessary for reproduction. Further, the performance of OASIS-ERIS is tested against a commercial measurement system in an Experimental Modal Analysis campaign.

The modal identification results showed barely any difference in identified eigenfrequencies between OASIS-ERIS and the commercial system. p. 0
Where the paper says it

Further, the performance of OASIS-ERIS is tested against a commercial measurement system in an Experimental Modal Analysis campaign. The results show that OASIS-ERIS closely matches the performance of the commercial system, making it a viable replacement for academia and projects with tightly constrained budgets.

The exact match of the identified mode shapes indicates that inter-device synchronization is successful, requiring responses from all sensors connected to different OASIS-ERIS boards. p. 0
Where the paper says it

Article title OASIS-ERIS: Open Acquisition System for IEPE Sensors - Electrically Refined and Inter-device Synchronization Authors Oliver M. Zobel∗1 , Johannes Maierhofer1 , Daniel J.

This demonstrates that the added inter-device synchronization is successful. p. 0
Where the paper says it

It is based on the Analog Devices AD7606C-18 analog-to-digital converter, offering 18-bit resolution on eight simultaneously sampled channels, and the Espressif ESP32-S3 microcontroller. The laboratory usability of OASIS-ERIS is significantly improved compared to OASIS-UROS due to the added inter-device synchronization.

The improved maximum sample rate of 100 kHz and the new software stack make OASIS-ERIS a substantial step toward a fully featured acquisition system for day-to-day lab use. p. 2
Where the paper says it

8 Hz at 3 dB Redesigned Connectors • Switch to SMB connectors • Significant weight reduction compared to previous version • Easier connection of sensors Versatile Mounting Options • M3 mounting holes in 90x90 mm grid • Allows secure attachment to devices • Vertical stacking for laboratory use Micro-Controller • Espressif ESP32-S3 chip • Hardware-generated PWM signal for robust sampling • C++ Firmware (ESP-IDF) Local Sample Cache • Samples are stored locally on each device’s SD card • Allows a fully autonomous device operation Inter-Device Synchronization • Connection through BNC • Connects the master sample clock to attached devices • Broadcasting of data acquisition settings via OneWire Synchronized Sampling 1) Master announces upcoming sample and the parameters 2) Connected devices prepare data acquisition 3) Master clock triggers samples of all devices at the ADC level 4) Samples are post-processed by each device independently Improved WiFi Interface • Refined on-board antenna • Connection of external antennas through an U. FL connector Core Specifications – Per Board Available channels 8 IEPE channels with SMB connector Sampling frequency 100 kHz per channel @ 18-bit resolution Voltage ranges ±2.

Conclusion on Viability

OASIS-ERIS is presented as a viable replacement for academia and projects with tightly constrained budgets due to its open-source license CC-BY 4.0 (Hardware) / MIT (Software) and its ability to closely match commercial performance. p. 0

Where the paper says it

The results show that OASIS-ERIS closely matches the performance of the commercial system, making it a viable replacement for academia and projects with tightly constrained budgets. Keywords Open-Source, Acquisition Hardware, Data Acquisition, Measurement Equipment, Experimental Dynamics, Vibration Analysis Specifications table Hardware name OASIS-ERIS Subject area Educational tools and open-source alternatives to existing commercial tools Hardware type Measuring physical properties and in-lab sensors Closest commercial analog OROS MODS OR10-DAQ-8 or similar compact acquisition systems with 8 IEPE channels and compact form factor Open-source license CC-BY 4.

The system offers the benefits of open-source software such as Openness, Freedom, Flexibility and Customization, Community and Collaboration, and Ownership. p. 1
Where the paper says it

• Flexibility and Customization: anyone can fully customize an existing project to fit their requirements. • Community and Collaboration: anyone can contribute to existing projects and improve them for everyone.

The low cost of hardware is a key motivation for the OASIS project. p. 1
Where the paper says it

The benefits of open-source hardware are the same as for software, but an additional advantage exists: an often significantly lower cost compared to commercial solutions. This advantage of open-source hardware is also the key motivation for the Open Acquisition System for IEPE Sensors (OASIS) 5 project.

The combination of features provides a substantial step toward a fully featured acquisition system for day-to-day lab use. p. 3
Where the paper says it

Custom Scripting • Full integration in existing frameworks using Python scripting • High level of hardware control OASIS-TUI • Guided terminal user interface • Optimized for remote operation, e. , using SSH Python API (OASIS-API) • Fully handles serial communication with devices • Provides robust and tested sampling routines • Ready-to-use structured HDF5 data storage OASIS-GUI • Complete graphical user interface • Easy-to-use solution intended for classical lab use Serial Communication (Virtual COM Port) C++ Device Firmware (ESP-IDF) • Open-Source and fully customizable • Low-level control of sampling hardware • Robust sampling procedure using SD card caching Figure 3: Overview of the current OASIS software stack.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved Inter-device Synchronization for Data Acquisition: The addition of inter-device synchronization allows a truly synchronized data acquisition can be achieved with an arbitrary number of acquisition boards by physically connecting sample clocks across devices, ensuring that the only delay between samples of the Sync Source and the Sync Sinks is due to the signal propagation delay between devices.

  2. Increased Sampling Frequency: The firmware migration to ESP-IDF enables a major increase of the achievable sampling frequency to 100 kHz, which supports higher fidelity measurements for structural dynamics compared to previous versions.

  3. Enhanced Data Transfer Speed: By utilizing a USB 1.1 connection with speeds up to approximately 12 Mbit/s instead of serial speeds of approximately 1 Mbit/s, the system significantly increases the transfer speed of sample data, allowing for faster processing on connected PCs/laptops.

  4. Flexible User Interfaces: The software stack includes an OASIS-GUI for classical lab use, an OASIS-TUI optimized for remote operation via SSH, and an OASIS-API that allows full integration in existing frameworks using Python scripting.

Abstract

OASIS-ERIS, the Open Acquisition System for IEPE Sensors - Electrically Refined and Inter-device Synchronization, is the successor to the previously released OASIS-UROS. It is based on the Analog Devices AD7606C-18 analog-to-digital converter, offering 18-bit resolution on eight simultaneously sampled channels, and the Espressif ESP32-S3 microcontroller. The laboratory usability of OASIS-ERIS is significantly improved compared to OASIS-UROS due to the added inter-device synchronization. By physically connecting the sample clocks across devices, a truly synchronized data acquisition can be achieved with an arbitrary number of acquisition boards. Additionally, a migration of the firmware to ESP-IDF allows a major increase of the achievable sampling frequency to 100 kHz. This paper documents the hardware and software stack of OASIS-ERIS, and provides all materials necessary for reproduction. Further, the performance of OASIS-ERIS is tested against a commercial measurement system in an Experimental Modal Analysis campaign. The results show that OASIS-ERIS closely matches the performance of the commercial system, making it a viable replacement for academia and projects with tightly constrained budgets.

Related papers