1.28 and 5.12 Gbps multi-channel twinax cable receiver ASICs for the ATLAS Inner Tracker Pixel Detector Upgrade
summary
The gist
We present two prototypes of a gigabit transceiver ASIC, GBCR1 and GBCR2, both designed in a 65-nm CMOS technology for the ATLAS Inner Tracker Pixel Detector readout upgrade<ref:2008.09738#pg2> The…
In short
Two gigabit transceiver ASICs, GBCR1 and GBCR2, were designed for the ATLAS Inner Tracker Pixel Detector upgrade using 65-nm CMOS technology. They feature different channel counts and equalization techniques to handle high-speed data transmission over twinax cables. The prototypes demonstrated good performance in terms of jitter reduction and radiation tolerance, suggesting they are viable solutions for the detector readout.
Key concepts
- Gigabit Transceiver ASIC
- This is a specialized integrated circuit designed to receive and transmit data at gigabit speeds. In this context, it acts as a bridge between the high-speed data coming from the detector pixels and the electronics that process that information. It handles both receiving signals (upstream) and sending signals (downstream).
- Equalization
- Equalization is a technique used to correct signal degradation caused by transmission channels, like cable loss. The ASIC uses structures like CTLE to introduce specific zeros and poles in its transfer function. This compensates for the frequency-dependent losses in the cables, helping to restore the original data quality.
- Peak-to-Peak Jitter
- Jitter refers to the variation in timing of a signal, which can cause errors in data reception. Peak-to-peak jitter measures the total variation between the highest and lowest points of this timing error. Lower peak-to-peak jitter indicates a cleaner, more reliable signal that is better suited for high-precision detector readout.
- Radiation Tolerance
- This describes how well the ASIC can function when exposed to radiation, such as gamma rays from a Co-60 source. The paper tested GBCR1 and found it could withstand a total ionizing dose of 200 kGy without significant performance degradation, which is crucial for operating inside large particle detectors like ATLAS.
Terminology used across episodes
This episode discusses
- 1.28 and 5.12 Gbps multi-channel twinax cable receiver ASICs for the ATLAS Inner Tracker Pixel Detector Upgrade · Paper Radio
The paper
1.28 and 5.12 Gbps multi-channel twinax cable receiver ASICs for the ATLAS Inner Tracker Pixel Detector Upgrade · Read on arXiv
Chufeng Chena, Datao Gonga, Suen Houc, Guangming Huangb, Xing Huanga, Szymon Kulisd, Paul Lerouxe, Chonghan Liua, Tiankuan Liua, Paulo Moreirad, Jeffery Prinziee, Peilong Wanga, Jingbo Yea
Department of Physics, Southern Methodist University · Department of Physics, Central China Normal University · Institute of Physics, Academia Sinica · Microelectronic group at CERN · KU Leuven
DOI: 10.1016/j.nima.2020.164439
Transcript
Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.
Kai: We're looking at the paper: "1.28 and 5.12 Gbps multi-channel twinax cable receiver ASICs for the ATLAS Inner Tracker Pixel Detector Upgrade".
Mira: Here's the gist of the paper. We present two prototypes of a gigabit transceiver ASIC, GBCR1 and GBCR2, both designed in a 65-nm CMOS technology for the ATLAS Inner Tracker Pixel Detector readout upgrade<ref:2008.09738#pg2> The single most informative sentence about the paper's subject and finding is: We present two prototypes of a gigabit transceiver ASIC, GBCR1 and GBCR2, both designed in a 65-nm CMOS technology for the ATLAS Inner Tracker Pixel Detector readout upgrade<ref:2008.09738#pg2>.
Kai: Prototype Descriptions GBCR1 has four upstream receiver channels and one downstream transmitter channel with pre-emphasis<ref:2008.09738#pg2> Each upstream channel receives the data at 5.12 Gbps through a 5 meter AWG34 Twinax cable from an ASIC driver located on the pixel module and restores the signal from the high frequency loss due to the low mass cable<ref:2008.09738#pg2> The downstream driver is designed to transmit the 2.56 Gbps signal from lpGBT to the electronics on the pixel module over the same cable<ref:2008.09738#pg2> GBCR2 has seven upstream channels and two downstream channels<ref:2008.09738#pg2> Each upstream channel works at 1.28 Gbps to recover the data directly from the RD53B ASIC through a 1 meter custom FLEX cable followed by a 6 meter AWG34 Twinax cable<ref:2008.09738#pg2> The downstream is designed to transmit the 160 Mbps signal from lpGBT through the same cable connection to RD53B and the jitter is about 157 ps at the cable ends<ref:2008.09738#pg2>.
Mira: Equalization Techniques The equalizer used in GBCR1 is based on a CTLE structure<ref:2008.09738#pg2> The passive resistor and capacitor create a zero and a pole in the transfer function to compensate for channel loss<ref:2008.09738#pg2> The equalization strength is determined by the ratio of the zero and the pole, as described in formula 3, EqualizationS trength = ωZ / ωp1 = 1 + RSCS squared (3)<ref:2008.09738#pg2> In GBCR2, a three-stage structure of CTLE is adopted to compensate with 3 order zero for high frequency range<ref:2008.09738#pg2> For the medium and low frequency parts, each of them just employs one CTLE stage to recover the signal loss in their range respectively<ref:2008.09738#pg2> The entire equalizer stage can provide 30 dB peaking strength at most<ref:2008.09738#pg2>.
Kai: Performance Metrics and Testing The peak-peak jitter (throughout the paper jitter is always peak-peak unless specified) of the restored signal is 35.4 ps at the output of GBCR1, and 138 ps for the downstream channel at the cable ends<ref:2008.09738#pg2> When the CDR is off and the retiming is bypassed, the peak-peak jitter is 79 ps and the random jitter is 4.3 ps (RMS) under the resistance setting of 0 and the capacitance setting of 3 of the equalizers<ref:2008.09738#pg2> When the CDR is turned on, the retiming circuit reduces the peak-peak jitter to 35 ps and the random jitter 1.5 ps (RMS)<ref:2008.09738#pg2> The total power consumption of GBCR1 is 192 mW<ref:2008.09738#pg2>.
Paper summary: Mira: Thinking about the whole paper, the title "one point two eight and five point one two Gbps multi-channel twinax cable receiver ASICs for the ATLAS Inner Tracker Pixel Detector Upgrade" really sums up what they did one <ref:2008.09738#pg1,1.28 and 5.12 Gbps multi-channel twinax cable receiver ASICs>.
Kai: It’s about presenting these two specific hardware solutions, GBCR1 and GBCR2, designed in sixty-five-nm CMOS technology for that specific detector upgrade one <ref:2008.09738#pg1,65-nm CMOS technology for>.
Lev: And the implication is that this work provides a tested design for handling gigabit per second data over low-mass electrical cables in a high radiation environment two.
Mira: It shows how different equalization techniques, like the CTLE structures, can be tuned to compensate for cable loss based on cable length one <ref:2008.09738#pg1>.
Kai: And they’ve shown that even with those adjustments, you can manage the jitter performance down to thirty-five picoseconds when the clock recovery is active two.
Lev: It proves that you can meet those demanding signal integrity targets for data transmission in that system, especially considering the radiation exposure two.
Mira: So, this paper lays out a blueprint for how to build these crucial receiver components needed for the ATLAS upgrade hardware one <ref:2008.09738#pg1>.
Conclusion: Kai: So, we’ve seen these two chip designs, GBCR1 and GBCR2, built in sixty-five nano meter silicon for that ATLAS detector upgrade one.
Mira: Yeah, the title itself is pretty specific: "one point two eight and five point one two gigabit per second multi-channel twinax cable receiver ASICs for the ATLAS Inner Tracker Pixel Detector Upgrade" one.
Lev: It’s about putting these chips into a real system where you’ve got these long, low-mass cables connecting everything two.
Kai: So, what does this mean when you look at the authors and the actual goals?
Mira: The goal is clearly to get data from that pixel detector readout working reliably over those specific cable lengths and speeds one.
Lev: But it’s a very constrained environment, especially because you have to worry about radiation, so they tested it with gamma rays up to two hundred kilo gray two.
Kai: So what are the big takeaways from these prototypes? What’s the actual result of all that simulation and testing?
Mira: They show GBCR1 with four upstream channels and one downstream channel using a CTLE structure for equalization one.
Lev: And they managed to keep the peak-to-peak jitter down to thirty five point four picoseconds at the output when the clock recovery is on two.
Kai: That’s pretty tight for high speed data, especially with those cable losses involved. But what about GBCR2?
Mira: GBCR2 has seven upstream channels and two downstream channels, working at a slower one point two eight gigabit per second for the upstream part one.
Lev: The downstream channel is optimized for one hundred sixty megabits per second, and they managed to reduce the interference jitter from five hundred picoseconds down to one hundred fifty seven picoseconds two.
Kai: So, it seems like these designs are making a very specific kind of data transmission possible in that detector setup.
Mira: Exactly. It shows how you can engineer those equalization stages with the right zero and pole placement to handle the channel loss effectively one.
Lev: The power consumption is also being managed pretty well; one chip uses about one hundred ninety two milli watts, which is reasonable for this kind of function two.
Kai: It’s a solid piece of hardware design, especially when you factor in that it survived the required radiation dose.
Mira: And they’re looking forward to testing GBCR2 soon to see how it performs in the actual lab setup.
Lev: It feels like a practical step toward getting those high-bandwidth links operational for the real ATLAS detector data.
More episodes
- 2610.34250-Yb/Sr optical clock comparison at 2.08E-18 uncertainty over a 1350-km fiber link
- 2610.36514-Integer electron-count cuts in variational second-order reduced-density-matrix theory. I. Molecular dissociation with fixed real-space and orbital partitions
- 2611.14082-Two atoms with strong light-induced dipolar interactions
- 2611.14040-Characterization of BNLs 20 and 30 micrometer thick LGADs for the Electron Ion Collider
- 2611.13399-Lift-element-based dynamic network of vortex gust-airfoil interactions
- 2611.13476-Hopfion Superlattices in 3D Twisted Moir'e Light Fields
- 2611.13642-Investigation of the timing performance of double-sided p-type 3D silicon sensors produced by CNM
- 2611.13830-SiPM optical readout of a PICOSEC Micromegas precise timing detector
- 2611.14152-Where are the shortest-path nodes in spatial networks?
- 2611.14219-Sub-Ice: semi-automated mapping of basal channels from ice shelf surface elevation data