Investigation of the timing performance of double-sided p-type 3D silicon sensors produced by CNM

summary

The gist

Investigation of the timing performance of double-sided p-type 3D silicon sensors produced by CNM is a study into how different geometric layouts and fabrication parameters affect the speed and…

In short

The study investigated how different geometric layouts and fabrication parameters affect timing signals in double-sided p-type 3D silicon sensors made by CNM. Three layouts were compared: hexagonal 30 µm, square 30 µm, and hexagonal 50 µm. Results show that timing resolution improves with bias voltage for all designs. At the highest bias, the square 30 µm geometry achieved the best average timing performance below 50 ps.

Key concepts

Double-Sided p-type 3D Silicon Sensors
These are specialized silicon detectors where both the n+ and p+ electrode columns are etched from opposite sides of the silicon substrate. This structure is used to decouple electrode spacing from sensor thickness, which enhances radiation hardness and allows for fast charge collection, making them suitable for high-energy physics applications.
Timing Resolution ($\sigma$)
This measures the precision of the sensor's ability to determine when a signal arrives. It is quantified by fitting the crossing-time distribution of laser signals with a Gaussian function. A smaller $\sigma$ indicates better timing accuracy, which is crucial for applications like particle tracking.
Spatial Uniformity ($U = \Delta\sigma/\sigma$)
This metric quantifies how consistent the timing resolution is across the sensor area. It measures the relative spread ($\Delta\sigma$) of local timing resolutions ($\sigma$) measured at different points during a laser scan. A lower value indicates better spatial uniformity, meaning the detector performs consistently across its surface.
Bias Voltage Dependence
The performance metrics, particularly timing resolution, are shown to improve as the applied bias voltage increases for all tested geometries. This suggests that higher electric fields generated by increased bias lead to faster charge collection and better signal timing in these 3D structures.

Terminology used across episodes

This episode discusses

The paper

Investigation of the timing performance of double-sided p-type 3D silicon sensors produced by CNM · Read on arXiv

C. Liao, C. Betancourt, M. Togawa, D. Bortoletto, N. Moffat, G. Pellegrini

International Center for Quantum-field Measurement Systems for Studies of the Universe and Particles (QUP, WPI) · SINTEF, Smart Sensors and Microsystems Institute of Norway · High Energy Accelerator Research Organization (KEK) · University of Oxford · Centro Nacional de Microelectrónica (CNM), CSIC

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: We're looking at the paper: "Investigation of the timing performance of double-sided p-type 3D silicon sensors produced by CNM".

Paper summary: Kai: So, we're looking at the paper "Investigation of the timing performance of double-sided p-type three dee silicon sensors produced by CNM," and it’s about how different physical shapes and voltages affect how fast these three dimensional silicon detectors respond and how consistent that response is in three dimensions <ref:2611.13642#pg1> <ref:2611.13642#pg1,Investigation of the timing performance of double-sided>.

Mira: Right, the authors are specifically comparing three layouts: a hexagonal geometry with thirty micrometer spacing, a square geometry with thirty micrometer spacing, and another hexagonal one with fifty micrometer spacing <ref:2611.13642#pg3>.

Lev: From an engineering standpoint, they're trying to figure out which physical design gives you the best timing resolution when you push the voltage up to its limit <ref:2611.13642#pg8>.

Kai: The main result they find is that for all three designs, increasing the applied voltage helps improve the timing resolution a bit <ref:2611.13642#pg9>.

Mira: But it’s not just about getting faster; it’s about which geometry performs best at that highest voltage, and in this case, it’s the square thirty micrometer layout <ref:2611.13642#pg9>.

Lev: They found that at their highest measured bias voltage, that square thirty micrometer sensor gives the best average timing resolution, staying under fifty picoseconds <ref:2611.13642#pg8>.

Kai: They also looked at how consistent the timing is across different spots inside those three deep cells because you can't just assume every point responds identically <ref:2611.13642#pg9>.

Mira: They quantified that inconsistency using a relative spread measure called U, and for those thirty micrometer layouts, that spread was around zero point one seven to zero point two over the voltage range they tested <ref:2611.13642#pg9>.

Lev: That spatial non uniformity is something we have to account for when designing the readout electronics, because it means not every pixel in your sensor will give you the same timing measurement <ref:2611.13642#pg8>.

Kai: The hexagonal fifty micrometer geometry showed much bigger non uniformity at low bias, but that inconsistency drops as you increase the bias voltage <ref:2611.13642#pg9>.

Mira: So the main point is that when you design these detectors for future high energy physics applications, like at the HL LHC, you need to consider both how much voltage you can apply and which specific electrode geometry gives you the best balance of speed and spatial consistency <ref:2611.13642#pg2>.

Lev: And that leads us into how this information affects the actual design process for those tracking systems we’re building for particle detectors next <ref:2611.13642#pg2>.

Conclusion: Kai: So, to wrap up this talk on the paper "Investigation of the timing performance of double-sided p-type three dee silicon sensors produced by CNM," we're talking about how they tested different physical shapes and voltages on these three dee detectors.

Mira: Yeah, it boils down to comparing hexagonal fifty micrometer spacing against square thirty micrometer spacing when you push the voltage high.

Lev: From my side, it’s about figuring out which geometry gives you a better signal-to-noise ratio when you're running real hardware under heavy load.

Kai: The authors show that resolution gets better with more bias voltage for all three types of sensors they tested.

Mira: But the square thirty micrometer layout wins out at the highest voltage, hitting under fifty picoseconds for the best average timing resolution.

Lev: If you're designing tracking systems for things like the HL LHC, that means favoring that square geometry and running it at its limit for better performance.

Kai: They also found how inconsistent the timing response is across different spots inside those cells using a measure called U.

Mira: They found that for those thirty micrometer layouts, that spread was around zero point one seven to zero point two over the voltage range they measured.

Lev: That spatial non uniformity is something we have to deal with in the readout electronics because every pixel won't give you the exact same timing measurement.

Kai: The hexagonal fifty micrometer geometry showed much bigger non uniformity when the voltage was low, but that inconsistency drops as you increase it.

Mira: So basically, for future high energy physics, you need to balance how much voltage you can apply with which specific electrode geometry gives you the best speed and consistency.

Lev: And that takes us into thinking about what this means for the actual design process of those particle tracking systems we're building next.

More episodes

← Home