Performance Analysis of a Dual-Polarised Bowtie Antenna in the Low RF Band: A Low-Cost Undergraduate Laboratory Experiment

arXiv:2611.15292 · astro-ph.IM · Submitted 2026-11-11 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Astrophysics. The day in astrophysics: observations, models and what the data forces.

Vera: We're looking at the paper: "Performance Analysis of a Dual-Polarised Bowtie Antenna in the Low RF Band".

Jocelyn: Here's the gist of the paper. The paper presents an undergraduate laboratory experiment to characterize a dual-polarised bowtie dipole antenna and analyze its performance in the low RF band using polarisation-rotation measurements Performance Analysis of a Dual-Polarised Bowtie Antenna in the Low RF Band: A Low-Cost Undergraduate Laboratory Experiment is an analysis of the performance of a dual-polarised bowtie dipole antenna and demonstrates its use through polarisation-rotation measurements Antenna Design and Characteristics The dual-polarised bowtie antenna is a Murchison Widefield Array (MWA) type antenna with crossed pair of bowtie-shaped elements made of aluminium having a wingspan of 0.74 m and a height of 0.40 m (measured) The vertical bowtie pairs are orthogonal to each other providing dual-linear polarisation The antenna is designed for the 80–320 MHz range.

Vera: Gain and directivity describe the concentration of radiated or received energy in a particular direction, while the radiation pattern describes how this energy is distributed spatially.

Jocelyn: Bowtie antennas offer a simple planar physical structure and stable performance over a wide bandwidth.

Vera: Radiation Pattern Analysis The radiation pattern of an antenna describes the variation of its radiated power with direction and is used to determine how electromagnetic energy is distributed in space.

Paper summary: Vera: This paper, "Performance Analysis of a Dual-Polarised Bowtie Antenna in the Low RF Band: A Low-Cost Undergraduate Laboratory Experiment," essentially presents an analysis of the performance of this dual-polarised bowtie antenna and demonstrates its use through polarisation-rotation measurements.

Jocelyn: The thesis is that by using this simple setup, they can characterize how the antenna responds to different polarisations, which is crucial for understanding how electromagnetic energy gets distributed in space.

Subrahmanyan: What matters here is that it shows the radiation pattern variation with frequency because experimental studies have shown that bowtie antennas generally exhibit broad dipole-like far-field radiation patterns, with changes in beamwidth and gain occurring across the operating frequency range seven fourteen fifteen <ref:2611.15292#pg3,experimental studies have shown that bowtie antennas generally exhibit broad dipole-like>.

Vera: They look at a horizontal cut at a ten degree elevation to see how the main lobes of the two ports cross along different axes for each polarisation. That’s how they map out what the antenna is actually radiating.

Jocelyn: And then they use polarization-rotation measurements, which is their main technique to find out the source angle by fitting the Malus equation to data points once power values are measured for each rotation.

Subrahmanyan: The cross-polarisation discrimination metrics they calculate, like one being ten log ten of P2 gamma over P2 beta, are used to measure how much power leaks between the two polarisation channels when the source polarisation is aligned with one.

Vera: They also discuss a notch filter they used to suppress radio frequency interference in the range of eighty to one hundred twenty MHz because it shows high attenuation there, especially for things like Delhi FM band signals.

Jocelyn: The paper’s findings confirm that the dual-polarised bowtie antenna responds to incident linear polarisation in a manner consistent with the Malus law model, with high quality fits across the tested frequency range.

Subrahmanyan: They find that the recovered source angles average deviate from a zero degree orientation by less than five degrees at all five frequencies, which they say is reasonable given how they manually aligned the transmitting dipole and the bowtie antenna.

Vera: It confirms that each of those two ports is linearly polarised and that those two ports are orthogonal to each other, which is a pretty solid check for this type of structure.

Jocelyn: So, what we’re seeing here is a practical demonstration using an undergraduate lab setup to characterize these kinds of antennas for real radio astronomy work.

Conclusion: Vera: The title of the paper, "Performance Analysis of a Dual-Polarised Bowtie Antenna in the Low RF Band: A Low-Cost Undergraduate Laboratory Experiment," really tells you what this whole thing is about—it’s about testing an antenna’s performance simply and affordably.

Jocelyn: And the authors are Robin Sen, Akshay Bhatia Neriyanuri, and Geetanjali Sethi from St. Stephen's College in Delhi who put this experiment together.

Subrahmanyan: What this means for the bigger picture is that it validates a simple physical structure like a bowtie antenna for use in radio astronomy setups because it works well across its operating frequency range and shows predictable polarisation behaviour.

Vera: It proves that you don't need massive, complex machinery to get these kinds of fundamental polarization characterizations done; this is accessible science.

Jocelyn: And they show the practical application by demonstrating how this antenna can be used within projects like the Sky Watch Array Network, which gives it real-world relevance in observational astronomy.

Subrahmanyan: The main implication is showing that these simple planar structures can be reliable enough for initial characterization before moving to more complex, large-scale array designs where you need high angular resolution.

Vera: It’s about building confidence in the hardware before you try to build the next generation of massive telescope receivers.

Robin Sen, Akshay Bhatia Neriyanuri, Geetanjali Sethi

Department of Physics, St. Stephen’s College, University of Delhi

astro-ph.IM

Submitted: 2026-11-11

Updated: 2026-11-11

Comments: 17 pages, 9 figures, 2 Tables

Code: https://github.com/NanoVNA-Saver/nanovna-saver

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 66/100

The gist: The paper presents an undergraduate laboratory experiment to characterize a dual-polarised bowtie dipole antenna and analyze its performance in the low RF band using polarisation-rotation…

Key concepts

Dual-Polarised Bowtie Antenna
This antenna uses two crossed, bowtie-shaped aluminum elements. These elements are oriented orthogonally to each other, which allows the antenna to interact with and respond differently to two independent linear polarizations simultaneously. This design is simple and stable across a wide frequency range.
Polarisation-Rotation Measurement
This method involves physically rotating a receiver antenna while measuring the received signal power at each step. By fitting this data to the Malus equation, researchers can determine the precise angle of the incident source's polarization relative to the antenna's axes.
Cross-Polarisation Discrimination (XPD)
XPD measures how much power is measured in one polarization state compared to an orthogonal state when the source is aligned with the first. Low XPD values indicate significant leakage between the two polarization channels, suggesting minor construction asymmetries in the antenna's arms.
Notch Filter Performance
A notch filter is a band-stop filter designed to significantly attenuate signals within a specific frequency range, such as 80–120 MHz. The study showed this filter effectively suppresses RFI from the Delhi FM band, demonstrating its utility for signal cleaning.

Terminology

Summary

The paper presents an undergraduate laboratory experiment to characterize a dual-polarised bowtie dipole antenna and analyze its performance in the low RF band using polarisation-rotation measurements

Performance Analysis of a Dual-Polarised Bowtie Antenna in the Low RF Band: A Low-Cost Undergraduate Laboratory Experiment is an analysis of the performance of a dual-polarised bowtie dipole antenna and demonstrates its use through polarisation-rotation measurements

Antenna Design and Characteristics

The dual-polarised bowtie antenna is a Murchison Widefield Array (MWA) type antenna with crossed pair of bowtie-shaped elements made of aluminium having a wingspan of 0.74 m and a height of 0. p. 1

Where the paper says it

Stephen’s College, Delhi is a Murchison Widefield Array (MWA) type antenna [11, 12] with a crossed pair of bowtie-shaped elements made of aluminium having a wingspan of 0. 74 m and a height of 0.

40 m (measured) The vertical bowtie pairs are orthogonal to each other providing dual-linear polarisation The antenna is designed for the 80–320 MHz range. p. 1
Where the paper says it

The vertical bowtie pairs are orthogonal to each other providing dual-linear polarisation. The antenna is designed for the 80–320 MHz range.

Gain and directivity describe the concentration of radiated or received energy in a particular direction, while the radiation pattern describes how this energy is distributed spatially. p. 1
Where the paper says it

Stephen’s College, Delhi Their performance is commonly described by parameters such as gain, directivity, radiation pattern, bandwidth, efficiency, and polarisation [4–6]. Gain and directivity describe the concentration of radiated or received energy in a particular direction, while the radiation pattern describes how this energy is distributed spatially.

Bowtie antennas offer a simple planar physical structure and stable performance over a wide bandwidth. p. 1
Where the paper says it

Bandwidth is also an important consideration, particularly for systems that require operation over a wide frequency range [4, 6]. Bowtie antennas offer a simple planar physical structure and stable performance over a wide bandwidth [7].

Radiation Pattern Analysis

The radiation pattern of an antenna describes the variation of its radiated power with direction and is used to determine how electromagnetic energy is distributed in space. A bowtie antenna exhibits a similar dipole-like radiation behaviour, with its principal radiation directed perpendicular to the antenna axis and reduced radiation along the axis. p. 1

Where the paper says it

For a conventional half-wave dipole, the radiation pattern is approximately doughnut-shaped in three dimensions, with maximum radiation in directions perpendicular to the antenna axis and nulls along its axis. A bowtie antenna exhibits a similar dipole-like radiation behaviour, with its principal radiation 2

Experimental studies have shown that bowtie antennas generally exhibit broad, dipole-like far-field radiation patterns, with changes in beamwidth and gain occurring across the operating frequency range. p. 2
Where the paper says it

However, unlike an ideal dipole, the radiation pattern of a bowtie can vary with frequency due to its broadband nature and finite dimensions. Experimental studies have shown that bowtie antennas generally exhibit broad, dipole-like far-field radiation patterns, with changes in beamwidth and gain occurring across the operating frequency range [7, 14, 15].

The horizontal cut at 10◦ elevation (Fig. p. 3
Where the paper says it

The horizontal cut at 10◦ elevation (Fig. 2(e)) shows the main lobes of the two ports crossed, along Y for polarisation 1 and along X for polarisation 2.

2(e)) shows the main lobes of the two ports crossed, along Y for polarisation 1 and along X for polarisation 2. p. 3
Where the paper says it

The horizontal cut at 10◦ elevation (Fig. 2(e)) shows the main lobes of the two ports crossed, along Y for polarisation 1 and along X for polarisation 2.

Polarisation Measurement Methodology

Once the power values are measured for each rotation of the receiver antenna, the Malus equation is fitted to the data points to find the polarisation angle of the source. The axis of the source dipole was aligned parallel to the polarisation 1 bowtie arms The output power of the RF signal transmitted by the TinySA is fixed at −27 dBm. p. 6

Where the paper says it

This orientation of the dual-pol bowtie is taken as 0 ◦ . The output power of the RF signal transmitted by the TinySA is fixed at −27 dBm.

The mean of ϕ (from Polarisation 1) and the offset-corrected ϕ (from Polarisation 2) is then taken as the angular position of the source. p. 6
Where the paper says it

To bring both estimates into a common reference frame, the fitted ϕ from Polarisation 2 is corrected by subtracting the 90◦ offset before averaging. The mean of ϕ (from Polarisation 1) and the offset-corrected ϕ (from Polarisation 2) is then taken as the angular position of the source.

Cross-Polarisation Discrimination Metrics

The cross-polarisation discrimination (XPD) can be measured. It is the ratio of power measured by one state of polarisation to that received in the orthogonal state, when the source polarisation is aligned with the former The cross-polarisation discrimination for polarisation 1 is given as: 10 log10(P2γ/P2β). p. 3

Where the paper says it

To specify how well an antenna distinguishes its two polarisations, the cross-polarisation discrimination (XPD) can be measured [17]. It is the ratio of power measured by one state of polarisation to that received in the orthogonal state, when the source polarisation is aligned with the former.

Similarly if γ is the best-fit angle for polarisation 2, then its cross-polarisation discrimination in dB is given by: 10 log10 (P1β/P1γ). p. 6
Where the paper says it

The next step is to calculate cross-polarisation discrimination (XPD) at different frequencies. If β is the best-fit angle for polarisation 1 at a specific frequency, and P1β and P2β are the power values of polarisation 1 and 2 at β, the cross-polarisation discrimination, in dB, for polarisation 1 is given as: 10 log10(P1β/P2β) (2) Similarly if γ is the best-fit angle for polarisation 2, then its cross-polarisation discrimination in dB is given by: 10 log10 (P2γ/P1γ) (3) However, the gain of both polarisation bowtie pairs is different.

Filter Performance and RFI Suppression

The notch filter attenuates signals in the range of 80–120 MHz and can be used to suppress RFI in this range. The attenuation is high in the range of 80–120 MHz, as seen in Figure 9. p. 2

Where the paper says it

Experimental studies have shown that bowtie antennas generally exhibit broad, dipole-like far-field radiation patterns, with changes in beamwidth and gain occurring across the operating frequency range [7, 14, 15]. Figure 2: Simulated radiation pattern of the dual-polarised bowtie over a perfect ground plane at 200 MHz, made with 4nec2 software [16].

The resulting RFI attenuation strongly suppresses the Delhi FM band for both polarisations. p. 7
Where the paper says it

The notch filter is then connected to the bowtie antenna to observe its frequency response. Attenuation of the RFI can be found out by comparing the frequency response of the antenna with and without the notch filter.

Study Limitations and Future Work

A few limitations of the present study should be noted: the rotation measurements were carried out manually in 15◦ steps using a disc-and-weight arrangement to track the antenna angle, which limits the angular resolution and introduces some uncertainty in the exact rotation angle at each step. The experiments were performed in an uncontrolled environment rather than an anechoic chamber, so reflections from the floor and walls, nearby scatterers, and ambient RFI could all contribute to the measured polarisation response and reduce the fit quality at some frequencies. Building on this work, future measurements could use a 3D printed rotation-and-measurement setup using a stepper motor and microcontroller like Arduino, allowing automatic, finer angular sampling and removing possible human error. p. 0

Where the paper says it

The antenna provides two orthogonal linear polarisation responses, allowing us to investigate the polarisation properties of radio-frequency signals using a simple and affordable experimental setup. In this article, we present our analysis of the performance of the antenna and demonstrate its use through polarisation-rotation measurements.

Conclusion of Polarisation Response

The polarisation-rotation measurements confirm that the dual-polarised bowtie antenna responds to incident linear polarisation in a manner consistent with the Malus-law model, with highquality fits (R2 generally above 0.85, and often above 0.95) across the tested frequency range. p. 0

Where the paper says it

This antenna is part of the Sky Watch Array Network (SWAN) and this analysis helps us understand the response of each individual array element in the setup. 1 Introduction Astronomical sources emit electromagnetic radiation across a broad range of frequencies, with different frequency ranges providing access to different astronomical phenomena [1].

p. 0
Where the paper says it

This antenna is part of the Sky Watch Array Network (SWAN) and this analysis helps us understand the response of each individual array element in the setup. 1 Introduction Astronomical sources emit electromagnetic radiation across a broad range of frequencies, with different frequency ranges providing access to different astronomical phenomena [1].

The recovered source angles ϕavg deviate from the true 0◦ orientation by less than 5◦ at all five frequencies, which is a reasonable level of agreement given the manual alignment of the transmitting dipole and the bowtie antenna. p. 7
Where the paper says it

5 Results Polarisation response of the bowtie By measuring the power received at various angles between the axis of the transmitting dipole and the receiving dual-polarised bowtie, we obtain the polarisation response of each port. As the bowtie is rotated about its boresight, the direction of arrival of the signal relative to the antenna, and hence the antenna gain in that direction, remains fixed; only the alignment between the incident electric field and the polarisation axis of each port changes.

p. 7
Where the paper says it

5 Results Polarisation response of the bowtie By measuring the power received at various angles between the axis of the transmitting dipole and the receiving dual-polarised bowtie, we obtain the polarisation response of each port. As the bowtie is rotated about its boresight, the direction of arrival of the signal relative to the antenna, and hence the antenna gain in that direction, remains fixed; only the alignment between the incident electric field and the polarisation axis of each port changes.

The measurements therefore confirm that each port is linearly polarised and that the two ports are orthogonal. p. 9
Where the paper says it

The eight-shaped figure arises because the received power is the product of the antenna’s co-polar response in the (fixed) direction of the source and the polarisation mismatch factor cos2 (∆θ). The measurements therefore confirm that each port is linearly polarised and that the two ports are orthogonal.

p. 9
Where the paper says it

The eight-shaped figure arises because the received power is the product of the antenna’s co-polar response in the (fixed) direction of the source and the polarisation mismatch factor cos2 (∆θ). The measurements therefore confirm that each port is linearly polarised and that the two ports are orthogonal.

Filter Characterization Details

The notch filter characterisation shows a well-defined stopband centred close to 100 MHz, with S21 dropping by more than 40 dB and S11 rising sharply in the same range. The resulting RFI attenuation strongly suppresses the Delhi FM band for both polarisations, although stations near the upper edge of the band (above about 103 MHz) are attenuated less, enabling daytime SWAN observations. p. 3

Where the paper says it

By combining observations from stations separated by large distances, SWAN can exploit interferometric techniques to achieve higher angular resolution than can be obtained with a single observing station. The system incorporates wide-band receiver instrumentation to support observations over a broad frequency range, with the receiver development focused on providing a practical and scalable platform for low-frequency radio astronomy.

The S-parameters vs frequency can be plotted to find out the operating frequency of the notch filter. p. 7
Where the paper says it

The NanoVNA is then connected to a laptop running NanoVNASaver software, which is a GUI application used to observe and save the measurements taken using the NanoVNA [27]. The CH0 port measures the S11 parameter, which describes the reflection from the filter at a particular frequency and is expressed in terms of the incident and reflected powers as S11(dB) = 10 log10 Preflected Pincident (10) The CH1 port measures the S21 parameter, which represents the forward transmission through the filter and is expressed in terms of the transmitted and incident powers as S21(dB) = 10 log10 Ptransmitted Pincident (11) By plotting the S-parameters vs frequency we can find out the operating frequency of the notch filter.

Acknowledgements and References

The authors are grateful to Prof. Avinash Deshpande for his constant support and to the Indian Institute of Technology, Kanpur for providing the notch filter The authors are also grateful to Dr. p. 3

Where the paper says it

By combining observations from stations separated by large distances, SWAN can exploit interferometric techniques to achieve higher angular resolution than can be obtained with a single observing station. The system incorporates wide-band receiver instrumentation to support observations over a broad frequency range, with the receiver development focused on providing a practical and scalable platform for low-frequency radio astronomy.

Jayasandhya Meenakshinathan for discussions and her guidance The paper includes references such as James J Condon and Scott M Ransom in Essential Radio Astronomy, Constantine A Balanis in Antenna Theory: Analysis and Design, and Richard C Compton et al. p. 0
Where the paper says it

The data obtained are also easy to analyse, and the analysis can be done in a classroom. 2 Dual-Polarised Bowtie Antenna Antennas are used to transmit and receive electromagnetic waves and form an essential part of wireless communication, radar, imaging, and radio astronomy systems.

on Bow-tie antennas on a dielectric half-space. The paper also references the Sky Watch Array Network (SWAN) project in KB Rao et al. p. 0
Where the paper says it

In this article, we present our analysis of the performance of the antenna and demonstrate its use through polarisation-rotation measurements. This antenna is part of the Sky Watch Array Network (SWAN) and this analysis helps us understand the response of each individual array element in the setup.

A wide-band RF receiver system for Sky Watch Array Network. p. 1
Where the paper says it

These have wide applications such as wireless communications [8], terahertz wave near-field imaging [9] and flexible RF devices [10]. The dual-polarised bowtie antenna used in the Sky Watch Array Network (SWAN) system at St.

The paper discusses the use of software defined radio platforms like Gqrx SDR and the NanoVNA vector network analyzer. p. 4
Where the paper says it

RTL-SDR receivers can acquire and digitise RF signals and provide a low-cost software-defined-radio platform for experimental measurements. The dual-polarised bowtie is rotated a full circle in steps of 15° and the power values received by both orthogonal elements are measured at each step using GQRX software, keeping the RTL-SDR AGC off.

The paper also references work on Iteratively reweighted least squares for maximum likelihood estimation. p. 6
Where the paper says it

This implies that peak accuracy is favoured over that of null, which affects the XPD estimate. This is corrected by performing the fit with weighted least squares, solved iteratively (Iteratively Reweighted Least Squares, IRLS) [24], wherein the weight is given by: 7

Filter Response Summary

As seen in Figure 8, the S11 magnitude shows a steep rise of more than 40 dB around 100 MHz. The trend shows that the notch filter transmits all signals except for a band around 100 MHz. S21 magnitude also drops around the same range implying that signals in this range are filtered out. p. 0

Where the paper says it

This antenna is part of the Sky Watch Array Network (SWAN) and this analysis helps us understand the response of each individual array element in the setup. 1 Introduction Astronomical sources emit electromagnetic radiation across a broad range of frequencies, with different frequency ranges providing access to different astronomical phenomena [1].

Therefore, the notch filter attenuates signals in the range of 80–120 MHz and can be used to suppress RFI in this range. p. 3
Where the paper says it

However, the RFI due to FM stations in Delhi lies within the operational frequency range of SWAN and thus restricts the observation time to night, when the RFI is not present. A notch filter has been developed by experts to attenuate this RFI so that astronomical measurements can be taken in the day as well.

The −3 dB stopband extends from about 72 to 121 MHz. p. 1
Where the paper says it

The vertical bowtie pairs are orthogonal to each other providing dual-linear polarisation. The antenna is designed for the 80–320 MHz range.

The rejection exceeds 20 dB from about 81 to 103 MHz, with a minimum of about −48 dB near 96 MHz, and falls to about 12 dB at the upper edge of the FM band (108 MHz). p. 1
Where the paper says it

The vertical bowtie pairs are orthogonal to each other providing dual-linear polarisation. The antenna is designed for the 80–320 MHz range.

XPD Leakage Interpretation

The measured XPD values, hovering around or below 20 dB, indicate a moderate and non-negligible amount of leakage between the two polarisation channels. Since the XPD of polarisation 2 is lower than that of polarisation 1 at four of the five frequencies, this leakage appears to be asymmetric, with more power from polarisation 2 spilling into polarisation 1 than vice versa. p. 6

Where the paper says it

The power measurements obtained across different rotation angles of the receiver are expected to carve a figure-of-eight on a polar graph, since the received power from a linearly polarised source varies as cos2 (θ − ϕ) for each port. The next step is to calculate cross-polarisation discrimination (XPD) at different frequencies.

This asymmetry could arise from small differences in the electrical and mechanical construction of the two bowtie arm pairs. p. 1
Where the paper says it

40 m (measured). The vertical bowtie pairs are orthogonal to each other providing dual-linear polarisation.

Future Measurement Directions

The paper suggests that future measurements could use a 3D printed rotation-and-measurement setup using a stepper motor and microcontroller like Arduino, allowing automatic, finer angular sampling and removing possible human error. This technique can be used to check whether the signal from a non-variable radio source in space is linearly polarised, since the received power from a linearly polarised signal varies as cos2 of the angle between the signal polarisation and the antenna axis, producing a distinct eight-shaped figure on rotation. p. 6

Where the paper says it

This process is repeated for different frequencies of the source signal. The power measurements obtained across different rotation angles of the receiver are expected to carve a figure-of-eight on a polar graph, since the received power from a linearly polarised source varies as cos2 (θ − ϕ) for each port.

This technique may be used to estimate the Faraday rotation measure (RM) along the line of sight, since the polarisation angle ψ of a linearly polarised wave passing through the Earth’s ionosphere varies as ψ(λ 2) = ψ0 + RM λ squared. p. 6
Where the paper says it

The power measurements obtained across different rotation angles of the receiver are expected to carve a figure-of-eight on a polar graph, since the received power from a linearly polarised source varies as cos2 (θ − ϕ) for each port. The next step is to calculate cross-polarisation discrimination (XPD) at different frequencies.

A denser frequency sweep across the full operating band, ideally automated using the TinySA and RTL-SDR in a scripted acquisition loop, would allow the frequency dependence of XPD and beamwidth to be mapped more completely. p. 4
Where the paper says it

RTL-SDR receivers can acquire and digitise RF signals and provide a low-cost software-defined-radio platform for experimental measurements. The dual-polarised bowtie is rotated a full circle in steps of 15° and the power values received by both orthogonal elements are measured at each step using GQRX software, keeping the RTL-SDR AGC off.

The experiments were performed and the data were analysed in the undergraduate laboratory of St. p. 0
Where the paper says it

Performance Analysis of a Dual-Polarised Bowtie Antenna in the Low RF Band: A Low-Cost Undergraduate Laboratory Experiment Robin Sen∗1 , Akshay Bhatia Neriyanuri†1 , and Geetanjali Sethi‡1 1Department of Physics, St. Stephen’s College, University of Delhi, Sudhir Bose Marg, Delhi 110007, India Abstract We have set up a simple experiment to characterise a dual-polarised bowtie dipole antenna at St.

Stephen’s College and helped students visualise the concept of polarisation and filters. p. 0
Where the paper says it

Stephen’s College as part of undergraduate radio astronomy experiments. The antenna provides two orthogonal linear polarisation responses, allowing us to investigate the polarisation properties of radio-frequency signals using a simple and affordable experimental setup.

Final Summary Statement

The polarization-rotation measurements confirm that the dual-polarised bowtie antenna responds to incident linear polarisation in a manner consistent with the Malus-law model, with highquality fits (R2 generally above 0.85, and often above 0.95) across the tested frequency range. The recovered source angles ϕavg deviate from the true 0◦ orientation by less than 5◦ at all five frequencies, which is a reasonable level of agreement given the manual alignment of the transmitting dipole and the bowtie antenna. The measurements therefore confirm that each port is linearly polarised and that the two ports are orthogonal. The paper presents a simple experiment to characterise a dual-polarised bowtie dipole antenna at St. p. 0

Where the paper says it

Performance Analysis of a Dual-Polarised Bowtie Antenna in the Low RF Band: A Low-Cost Undergraduate Laboratory Experiment Robin Sen∗1 , Akshay Bhatia Neriyanuri†1 , and Geetanjali Sethi‡1 1Department of Physics, St. Stephen’s College, University of Delhi, Sudhir Bose Marg, Delhi 110007, India Abstract We have set up a simple experiment to characterise a dual-polarised bowtie dipole antenna at St.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Data acquisition can be automated using a stepper motor and microcontroller like Arduino to allow for automatic, finer angular sampling and remove possible human error from rotation measurements. This technique can be used to check whether the signal from a non-variable radio source in space is linearly polarised, since the received power from a linearly polarised signal varies as cos2 of the angle between the signal polarisation and the antenna axis, producing a distinct eight-shaped figure on rotation.

  2. The system can be extended to quantify element-to-element variation by applying this single-antenna characterisation to multiple deployed elements within an array. This would help in quantify element-to-element variation across the SWAN array network.

  3. A denser frequency sweep across the full operating band, ideally automated using the TinySA and RTL-SDR in a scripted acquisition loop, would allow for a more complete mapping of XPD and beamwidth dependence on frequency. This would enable a more comprehensive characterisation of how the frequency dependence of XPD and beamwidth is mapped more completely.

  4. The system can be used to estimate the Faraday rotation measure (RM) along the line of sight by measuring the polarization angle psi at several frequencies and fitting Equation 12. This allows for determining the ionospheric RM [28, 29], which is critical for understanding how the polarisation angle psi of a linearly polarised wave passing through the Earth’s ionosphere varies as psi(lambda 2) = psi0 + RM lambda squared.

Abstract

We have set up a simple experiment to characterise a dual-polarised bowtie dipole antenna at St. Stephens College as part of undergraduate radio astronomy experiments. The antenna provides two orthogonal linear polarisation responses, allowing us to investigate the polarisation properties of radio-frequency signals using a simple and affordable experimental setup. In this article, we present our analysis of the performance of the antenna and demonstrate its use through polarisation-rotation measurements. This antenna is part of the Sky Watch Array Network (SWAN) and this analysis helps us understand the response of each individual array element in the setup.

Related papers