The infrared unmodulated pyramid wavefront sensor: simulations, lab and on sky

arXiv:2611.08028 · astro-ph.IM · Submitted 2026-11-05 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Astrophysics. The day in astrophysics: observations, models and what the data forces.

Vera: We're looking at the paper: "The infrared unmodulated pyramid wavefront sensor".

Jocelyn: Here's the gist of the paper. Direct imaging of Earth-like exoplanets requires strong suppression of stellar light at small angular separations, achievable with extreme adaptive optics (XAO) The IR-umPWFS is a strong candidate for future XAO systems because operating in the infrared extends the linear range sufficiently to remove the need for modulation, enabling higher loop speeds that are no longer limited by the speed of the modulation mirror Feasibility and Performance Assessment The performance of the IR-umPWFS was evaluated through a combination of end-to-end numerical simulations, lab tests, and on-sky observations conducted on the PAPYRUS adaptive optics bench at the Observatoire de Haute-Provence (OHP) Simulations show reliable operation over a broad range of conditions, reaching Strehl ratios up to ∼60% at 1400 nm for seeing up to 4′′ Laboratory results validate the simulations and confirm the pyramid quality On sky, stable closed-loop operation was achieved over three nights.

Vera: System Comparison and Advantages The IR-umPWFS operating at 1000 Hz showed gains of ∼ 1.63 in Strehl ratio and ∼ 1.26 in encircled energy, along with a ∼ 2.03-fold reduction in residual wavefront error compared to the VIS-mPWFS operating at 500 Hz.

Jocelyn: The advantages being tested include the pyramid geometry (3- vs 4-sided, the latter with a roof defect), the sensing wavelength and the absence of modulation with the resulting higher loop speed, and different non-common path aberrations whose contribution is removed from the Strehl ratios.

Vera: The IR-umPWFS remained robust to tip-tilt offsets up to 3 λ/D at 1400 nm.

Paper summary: Vera: So, we're looking at this paper about "The infrared unmodulated pyramid wavefront sensor: simulations, lab and on sky." Basically, they’re talking about how to get really good direct imaging of Earth-like exoplanets.

Jocelyn: And for that, you need extreme adaptive optics to suppress the star's light at very small angles. The paper focuses on a specific type of sensor called a pyramid wavefront sensor, or PWFS.

Subrahmanyan: Which is important because these sensors are sensitive to low-order aberrations, which are the big stuff we need to fix when trying to see faint things like Proxima b, which this paper mentions.

Vera: Right. The main point of this work is that they've designed something called the infrared unmodulated PWFS that doesn't use modulation. They claim operating in the infrared extends the range enough that you don't need modulation anymore, which lets them run at higher loop speeds without being limited by how fast a mirror can spin.

Jocelyn: It seems they’re testing this concept across simulations, lab tests, and even on-sky observations at the Observatoire de Haute-Provence. The thesis is that this infrared unmodulated sensor is a strong candidate for future adaptive optics systems because it allows for higher loop speeds without needing modulation to achieve the necessary performance gains.

Subrahmanyan: That implies that if we can get faster correction loops, we can actually achieve sharper point spread functions and better corrections in real-time, which is crucial for these direct imaging goals. What are the key claims they are making about this sensor?

Vera: They show that simulations suggest reliable operation over a wide range of conditions, reaching Strehl ratios up to sixty percent at one thousand four hundred nanometers for seeing conditions as bad as four arcseconds. On the sky, they actually achieved stable closed-loop operation over three nights.

Jocelyn: And when they compare it to an older system, like the VIS-mPWFS operating at five hundred hertz, the IR-umPWFS operating at one thousand hertz showed gains of about one point six three in Strehl ratio and about one point two six in encircled energy compared to that other system.

Subrahmanyan: That suggests a significant improvement when you increase the loop speed, especially when you look at those residual wavefront errors dropping by two point zero three fold compared to the VIS-mPWFS running at five hundred hertz. So, the gain isn't just from speed; it's also about reducing those other kinds of aberrations that aren't common path aberrations.

Paper summary: Vera: They tested different pyramid geometries and sensing wavelengths, and they found that using a three-sided pyramid actually helped avoid the roof defect issue that can plague the classical four-sided design, which they showed is about thirty one point two micrometers along the roof ridge at one thousand four hundred nanometers <ref:2611.08028#pg1>.

Jocelyn: And because of this geometry and no modulation, they were able to keep it robust even to tip-tilt offsets up to three lambda over D at one thousand four hundred nanometers <ref:2611.08028#pg1>. That’s a big piece of information for real sky conditions.

Subrahmanyan: From a theoretical standpoint, that robustness against large tip-tilt errors at that wavelength is interesting because it means the sensor isn't overly sensitive to those kinds of errors when you're trying to correct things in the infrared. Which observation would confirm this level of stability?

Vera: The on-sky results showed that the IR-umPWFS consistently outperformed the VIS-mPWFS, with average gains of about one point six three in Strehl and about one point two six in encircled energy over those three nights.

Jocelyn: But there's a caveat here because they compared it at different loop speeds, and their comparison between five hundred hertz and one thousand hertz wasn't conclusive when looking only at the speed increase itself.

Subrahmanyan: That’s a fair point, Jocelyn. It suggests that the performance gain might not come purely from increasing the loop speed alone, but more from reducing those residual aberrations that are present in both systems.

Vera: They found that the optical gain for the IR-umPWFS is high and nearly flat at about zero point eight five, while in the VIS-mPWFS case, it varies between zero point three and zero point five.

Jocelyn: And they noted a clear drop in that optical gain for modes within the modulation radius in the VIS-mPWFS case, which is something that's absent when you remove modulation for the IR-umPWFS. That suggests that removing modulation preserves the sensor sensitivity in a way that speed alone doesn't fully capture.

Subrahmanyan: So, it seems like high loop speed helps mitigate temporal errors under poor seeing conditions, but the fundamental gain comes from how the sensor handles those aberrations at this infrared wavelength compared to visible light systems. What does this mean for our bigger picture of exoplanet characterization?

Paper summary: Vera: It means that if we can build these unmodulated sensors, we have a better tool for getting the sharp images needed to actually characterize atmospheres, like the one they are targeting with Proxima b.

Jocelyn: They are aiming for a total wavefront error below seventy nanometers RMS at seven hundred fifty nanometers, which is what's required to meet those contrast and Strehl ratio targets for observing reflected light from that type of exoplanet.

Subrahmanyan: To confirm this, we need observations that can reliably measure those low-order wavefront errors and the petal modes they are sensitive to. That would be a crucial follow-up observation to see if this sensor performs as well when looking at real targets in a complex system like an XAO setup.

Vera: So, to summarize this paper, "The infrared unmodulated pyramid wavefront sensor: simulations, lab and on sky," they’ve shown that using an infrared unmodulated pyramid wavefront sensor is a promising path forward for direct imaging because it allows for higher loop speeds without modulation, leading to better performance gains in terms of Strehl ratio and encircled energy.

Jocelyn: The authors point out the importance of the pyramid's tip quality, showing that a three-sided design avoids a major issue with the four-sided pyramid structure by mitigating the roof defect. This is something we need to keep in mind when designing future wavefront sensors for these high-contrast imaging missions.

Subrahmanyan: The implication for cosmology and structure formation is less direct, but it shows that engineering solutions in adaptive optics can get extremely specific performance boosts when you look at the required sensitivity of the instruments. It confirms that we can design tools that are tuned precisely to the physics of what we're trying to observe.

Vera: So, they’ve moved this concept from just theory into concrete lab tests and on-sky validation, showing it works under realistic turbulence conditions for high contrast imaging needs.

Jocelyn: This paves the way for instruments like the VLT/RISTRETTO instrument because infrared operation removes that modulation bottleneck, letting us push those correction loop speeds even further.

Subrahmanyan: And what they’re asking for next is calibration strategy improvements and testing with an appropriate reference image to fully understand the system's performance limits. We need more data on how this sensor behaves when you try to correct things under more complex noise environments.

Conclusion: Vera: So, we're wrapping up this look at "The infrared unmodulated pyramid wavefront sensor: simulations, lab and on sky." It’s about how they proved that using an infrared unmodulated pyramid wavefront sensor is a solid way to push adaptive optics further for direct imaging.

Jocelyn: Yeah, it boils down to the fact that you don't need modulation anymore if you operate in the infrared because the range is big enough.

Subrahmanyan: From my end, it’s about engineering a system that can correct those low-order errors with higher loop speeds.

Vera: Exactly. They showed simulations and lab tests work well, and they even got stable on the sky for three nights at four arcseconds of seeing conditions.

Jocelyn: And the results were pretty compelling when they compared it to older systems, showing gains in Strehl ratio and encircled energy with that higher loop speed.

Subrahmanyan: It means we can get sharper images faster, which is crucial for catching those faint exoplanet signals. But we need to see if that gain holds up under real sky noise.

Vera: That’s the thing they're pushing next, though; they’re looking at how to improve the calibration strategy and test it with a better reference image.

Jocelyn: Right. They also have to figure out how to handle those trefoil aberrations that pop up in these systems.

Subrahmanyan: If they can nail those limitations, this sensor design could become a real workhorse for future high-contrast imaging missions across the board.

Muskan Shinde, Nicolas Blind, Isaac Dinis, Sylvain Cetre, Angelie Alagao, Francisco Oyarzun, Romain Fétick, Matteo Pasinetti, Nathanaël Restori, Christophe Lovis, Vincent Chambouleyron**, and others

Geneva Observatory, University of Geneva, Chemin Pegasi 51, 1290 Versoix, Switzerland · Wakea Consulting Grenoble, France · Aix Marseille Univ CNRS CNES LAM Marseille, France · Aix Marseille Univ CNRS Pytheas OHP Observatoire de Haute-Provence

astro-ph.IM

Submitted: 2026-11-05

Updated: 2026-11-05

Comments: Accepted for publication in A&A. 16 pages, 21 figures, 7 tables

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 84/100

The gist: Direct imaging of Earth-like exoplanets requires strong suppression of stellar light at small angular separations…

Key concepts

Adaptive Optics (AO)
Adaptive Optics uses a deformable mirror to correct distortions in a telescope's light path caused by atmospheric turbulence. This process works by measuring how the incoming light is distorted and then rapidly changing the shape of the mirror to counteract those distortions, resulting in a sharper final image.
Strehl Ratio
The Strehl ratio is a measure of image quality that tells you how close your actual image is to an ideal, diffraction-limited point spread function. A higher Strehl ratio means the final image is sharper and has less blurring caused by optical imperfections or atmospheric turbulence.
Loop Speed
Loop speed refers to how quickly the adaptive optics system can measure wavefront errors and adjust the deformable mirror accordingly. A faster loop speed allows the system to correct rapid changes in atmospheric turbulence more effectively, leading to better temporal correction and sharper images.

Terminology

Summary

Direct imaging of Earth-like exoplanets requires strong suppression of stellar light at small angular separations, achievable with extreme adaptive optics (XAO) The IR-umPWFS is a strong candidate for future XAO systems because operating in the infrared extends the linear range sufficiently to remove the need for modulation, enabling higher loop speeds that are no longer limited by the speed of the modulation mirror

Feasibility and Performance Assessment

The performance of the IR-umPWFS was evaluated through a combination of end-to-end numerical simulations, lab tests, and on-sky observations conducted on the PAPYRUS adaptive optics bench at the Observatoire de Haute-Provence (OHP) Simulations show reliable operation over a broad range of conditions, reaching Strehl ratios up to ∼60% at 1400 nm for seeing up to 4′′ Laboratory results validate the simulations and confirm the pyramid quality On sky, stable closed-loop operation was achieved over three nights.

System Comparison and Advantages

The IR-umPWFS operating at 1000 Hz showed gains of ∼ 1.63 in Strehl ratio and ∼ 1. p. 0

Where the paper says it

Compared with the VIS-mPWFS operating at 500 Hz, the IR-umPWFS operating at 1000 Hz showed gains of ∼ 1. 63 in Strehl ratio and ∼ 1.

26 in encircled energy, along with a ∼ 2. p. 0
Where the paper says it

63 in Strehl ratio and ∼ 1. 26 in encircled energy, along with a ∼ 2.

03-fold reduction in residual wavefront error compared to the VIS-mPWFS operating at 500 Hz. p. 0
Where the paper says it

26 in encircled energy, along with a ∼ 2. 03-fold reduction in residual wavefront error.

The advantages being tested include the pyramid geometry (3- vs 4-sided, the latter with a roof defect), the sensing wavelength and the absence of modulation with the resulting higher loop speed, and different non-common path aberrations whose contribution is removed from the Strehl ratios. p. 0
Where the paper says it

03-fold reduction in residual wavefront error. This is a system-level comparison, as the two arms differ in several parameters: the pyramid geometry (3- vs 4-sided, the latter with a roof defect), the sensing wavelength and the absence of modulation with the resulting higher loop speed, which are the advantages being tested, and the different non-common path aberrations, whose contribution is removed from the Strehl ratios.

The IR-umPWFS remained robust to tip-tilt offsets up to 3 λ/D at 1400 nm. p. 0
Where the paper says it

This is a system-level comparison, as the two arms differ in several parameters: the pyramid geometry (3- vs 4-sided, the latter with a roof defect), the sensing wavelength and the absence of modulation with the resulting higher loop speed, which are the advantages being tested, and the different non-common path aberrations, whose contribution is removed from the Strehl ratios. The IR-umPWFS remained robust to tip-tilt offsets up to 3 λ/D at 1400 nm.

Laboratory Validation and Optical Quality

The choice of a 3-sided pyramid wavefront sensor was motivated by its ability to mitigate the roof defect issue found in the classical 4-sided design, as it does not suffer from the same roof defect. The measured edge (and apex) width of the 3-sided pyramid was better than 3. p. 2

Where the paper says it

The pyramid shown is a glass prism manufactured by AllInOptics, with a small apex angle of less than 2◦ . No roof defect is present, and the measured edge (and apex) width is better than 3.

86 µm, allowing operation at focal ratios as low as f /24. p. 2
Where the paper says it

86 µm (measurement is limited by the diffraction of the microscope used for the inspection). This level of accuracy allows operation at focal ratios as low as f /24.

Simulations showed that 3-sided and 4-sided PWFSs showed very similar performance across sensitivity, dynamic range, and optical gains. p. 2
Where the paper says it

This level of accuracy allows operation at focal ratios as low as f /24. We performed simulations to test the performance, under the same conditions, of 3-sided and 4-sided PWFSs on several aspects including sensitivity, dynamic range and optical gains, and they showed very similar performance (Shinde et al.

On-Sky Results and Temporal Stability

The IR-umPWFS successfully closed the AO loop under varying turbulence conditions, achieving Strehl ratios of approximately 60% at λPSF = 1400 nm for seeing conditions up to 4′′. The higher loop speed enables improved temporal correction, resulting in sharper PSFs and higher Strehl The IR-umPWFS consistently outperforms the VIS-mPWFS, with average gains of ∼ 1. p. 9

Where the paper says it

4 ′′ higher loop speed is a major contributor to the observed gain, although the on-sky data do not allow its contribution to be separated from that of infrared, unmodulated sensing. The higher loop speed enables improved temporal correction, resulting in sharper PSFs and higher Strehl.

63 in Strehl and ∼ 1. p. 0
Where the paper says it

The performance of the IR-umPWFS is evaluated through a combination of end-to-end numerical simulations, lab tests, and on-sky observations conducted on the PAPYRUS adaptive optics bench at the Observatoire de Haute-Provence (OHP). Simulations show reliable operation over a broad range of conditions, reaching Strehl ratios up to ∼60% at 1400 nm for seeing up to 4′′.

26 in EE.

Conclusion and Future Directions

The IR-umPWFS is a promising candidate for the VLT/RISTRETTO instrument because infrared operation extends the linear range sufficiently to remove the need for modulation, enabling higher loop speeds that are no longer limited by the speed of the modulation mirror. Future work will focus on improving calibration strategy, tests with an appropriate reference image, as well as the implementation of strategies to mitigate trefoil aberrations. The current system performance was limited by the speed of the DM, restricting operation to approximately 1000 Hz. p. 0

Where the paper says it

Ultimately, performance at small inner working angles is limited by low-order residual wavefront errors (WFE). Extreme adaptive optics (XAO) systems are therefore essential, as they provide the high wavefront quality and stability required to reach high contrast at separations as small as 1–2 λ/D to fully exploit the angular resolution of current 8–10 m class telescopes.

p. 0
Where the paper says it

Ultimately, performance at small inner working angles is limited by low-order residual wavefront errors (WFE). Extreme adaptive optics (XAO) systems are therefore essential, as they provide the high wavefront quality and stability required to reach high contrast at separations as small as 1–2 λ/D to fully exploit the angular resolution of current 8–10 m class telescopes.

p. 0
Where the paper says it

Ultimately, performance at small inner working angles is limited by low-order residual wavefront errors (WFE). Extreme adaptive optics (XAO) systems are therefore essential, as they provide the high wavefront quality and stability required to reach high contrast at separations as small as 1–2 λ/D to fully exploit the angular resolution of current 8–10 m class telescopes.

Pruning redundant reasoning tokens

The IR-umPWFS operating at 500 Hz versus 1000 Hz comparison showed that while increasing loop speed is expected to improve performance, the trend was not observed in the on-sky dataset. The comparison between the two wavefront sensing schemes at equal loop speed of 500 Hz was inconclusive The results suggest that performance gains originate from reduced residual aberrations, as seen in the reduction of RMS WFE. p. 9

Where the paper says it

For each dataset, the loop gain and the number of controlled modes were optimized to maximize performance. At equal loop speed, the comparison between the two wavefront sensing schemes is inconclusive.

Where the gains come from

The optical gain for the IR-umPWFS is nearly flat and high, at ∼0.85, while those of the VIS-mPWFS vary between 0. p. 6

Where the paper says it

Because the AO lab bench used the same DAO framework, much of the software developed and validated during the bench experiments could be directly reused on the PAPYRUS system, allowing integration within a few hours. The VIS-mPWFS was operated using the PAPYRUS RTC implementation, while the IR-umPWFS was operated through our control pipeline validated on the bench in Geneva (Sect.

3 and 0.5. A clear drop in optical gain is observed for modes within the modulation radius in the VIS-mPWFS case, whereas the absence of modulation in the IR-umPWFS preserves the sensor sensitivity. p. 6
Where the paper says it

For the VIS-mPWFS, the impact of the roof defect is mitigated by the 5 λ/D modulation, which moves the PSF over a region much larger than the defect. The infrared sensing wavelength, the absence of modulation and the resulting higher loop speed are precisely the advantages of the IR-umPWFS investigated in this work: infrared operation extends the linear range sufficiently to remove the need for modulation, and without modulation the loop speed is no longer limited by the modulation mirror speed.

The higher loop speed alone can account for a large part of this gain. p. 0
Where the paper says it

The IR-umPWFS is a strong candidate for future XAO systems: operating in the infrared extends the linear range sufficiently to remove the need for modulation, enabling higher loop speeds that are no longer limited by the speed of the modulation mirror, which contributed to the significantly improved on-sky performance. The OHP turbulence conditions (D/r0 ∼ 17 at 1400 nm) are comparable to typical Very Large Telescope (VLT) conditions (D/r0 ∼ 20), supporting the relevance of these results for VLT/RISTRETTO.

How the training signal is built

The calibration process involved iteratively calibrating the system as close as possible to the reference phase, using an initial calibration followed by closing the AO loop on the internal calibration source. The resulting set of DM commands defines the final DM flat. p. 7

Where the paper says it

This process is repeated until the PWFS measurements converge to a uniform intensity distribution among the pupil images. The resulting set of DM commands defines the final DM flat.

The reference image used was a synthetic flat reference based on the valid-pixel mask, which introduced a residual trefoil aberration of approximately 75 nm RMS. p. 7
Where the paper says it

In our case, we used the valid pixel mask as a synthetic reference (the reason for this choice is described in Sect. 2), which however does not correspond to a flat wavefront.

The performance measured on the PAPYRUS bench is representative of what can be expected at the VLT because the seeing conditions correspond to D/r0 ∼ 17 at 1400 nm, which is comparable to typical VLT conditions of D/r0 ∼ 20. The IR-umPWFS was able to compensate for the offset of 3 λPSF/D between the two pyramids reliably, demonstrating its capability to correct large tip-tilt errors. p. 8

Where the paper says it

Due to the absence of atmospheric dispersion correction, a tip-tilt offset of ∼ 3 λPSF/D at λPSF = 1400 nm was present between the WFSs. Although beyond the linear regime, both sensors compensated it effectively, allowing stable operation and switching, demonstrating robustness to large tip-tilt offsets and potential vibrations.

The on-sky data do not allow these contributions to be separated from that of infrared, unmodulated sensing. p. 9
Where the paper says it

4 ′′ 2. 4 ′′ higher loop speed is a major contributor to the observed gain, although the on-sky data do not allow its contribution to be separated from that of infrared, unmodulated sensing.

p. 9
Where the paper says it

4 ′′ 2. 4 ′′ higher loop speed is a major contributor to the observed gain, although the on-sky data do not allow its contribution to be separated from that of infrared, unmodulated sensing.

p. 9
Where the paper says it

4 ′′ 2. 4 ′′ higher loop speed is a major contributor to the observed gain, although the on-sky data do not allow its contribution to be separated from that of infrared, unmodulated sensing.

p. 9
Where the paper says it

4 ′′ 2. 4 ′′ higher loop speed is a major contributor to the observed gain, although the on-sky data do not allow its contribution to be separated from that of infrared, unmodulated sensing.

The IR-umPWFS operating at 500 Hz versus 1000 Hz comparison showed that the performance gain is robust across all observations. The tip-tilt jitter remains below one pixel for all observations, despite observation sequences ranging from a few seconds to several minutes The IR-umPWFS operating at 1000 Hz consistently demonstrated better performance than the VIS-mPWFS operating at 500 Hz, with improvements in both Strehl ratio and EE. p. 9

Where the paper says it

Overall, the tip-tilt jitter remains below one pixel for all observations, despite observation sequences ranging from a few seconds to several minutes, indicating stable closed-loop performance in both configurations. Comparison of the Strehl (top), EE (middle), and RMS WFE (bottom) for several observations with the IR-umPWFS (green; 1000 Hz) and VIS-mPWFS (blue; 500 Hz).

The on-sky data do not allow these contributions to be separated from that of infrared, unmodulated sensing.

The IR-umPWFS operating at 500 Hz versus VIS-mPWFS 500 Hz comparison was inconclusive because lower Strehl ratios were obtained with the IR-umPWFS in some observations due to instabilities. The discrepancy is likely due to the dominance of temporal lag errors in the error budget at 500 Hz, which limits the achievable correction. p. 9

Where the paper says it

2018) for the IRumPWFS. This discrepancy is likely due to the dominance of temporal lag errors in the error budget at 500 Hz, which limits the achievable correction and may mask the potential advantage of the IR-umPWFS operated at longer wavelengths.

The on-sky data do not allow these contributions to be separated from that of infrared, unmodulated sensing.

Increasing the loop speed from 500 Hz to 1000 Hz significantly improves performance, particularly under poor seeing and high wind speeds where temporal lag errors dominate. These results demonstrate that increasing the loop speed is an effective way to mitigate temporal errors and maintain high Strehl ratios under realistic observing conditions. The current system performance was limited by the speed of the DM, restricting operation to approximately 1000 Hz. Further tests with a faster DM are therefore required to fully demonstrate the performance gains achievable at higher loop speeds (> 2 kHz). p. 0

Where the paper says it

Ultimately, performance at small inner working angles is limited by low-order residual wavefront errors (WFE). Extreme adaptive optics (XAO) systems are therefore essential, as they provide the high wavefront quality and stability required to reach high contrast at separations as small as 1–2 λ/D to fully exploit the angular resolution of current 8–10 m class telescopes.

p. 0
Where the paper says it

Ultimately, performance at small inner working angles is limited by low-order residual wavefront errors (WFE). Extreme adaptive optics (XAO) systems are therefore essential, as they provide the high wavefront quality and stability required to reach high contrast at separations as small as 1–2 λ/D to fully exploit the angular resolution of current 8–10 m class telescopes.

The integration of more advanced control algorithms, such as DD4AO and PO4AO, is expected to further enhance the overall performance and stability of the system. p. 6
Where the paper says it

As part of this work, we developed the necessary DAO software interface to integrate the infrared arm into the PAPYRUS control architecture. Because the AO lab bench used the same DAO framework, much of the software developed and validated during the bench experiments could be directly reused on the PAPYRUS system, allowing integration within a few hours.

p. 6
Where the paper says it

As part of this work, we developed the necessary DAO software interface to integrate the infrared arm into the PAPYRUS control architecture. Because the AO lab bench used the same DAO framework, much of the software developed and validated during the bench experiments could be directly reused on the PAPYRUS system, allowing integration within a few hours.

The IR-umPWFS operating at 1000 Hz consistently demonstrated better performance than the VIS-mPWFS operating at 500 Hz, with improvements in both Strehl ratio and EE. The on-sky data do not allow these contributions to be separated from that of infrared, unmodulated sensing. Further tests with both sensors operating at the same speed are needed to confirm the gain of operation at infrared wavelengths. p. 0

Where the paper says it

Infrared operation improves linearity, reduces optical-gain variations and modal cross-talk. Laboratory results validate the simulations and confirm the pyramid quality.

The IR-umPWFS is a promising candidate for the VLT/RISTRETTO instrument. p. 0
Where the paper says it

The IR-umPWFS is a strong candidate for future XAO systems: operating in the infrared extends the linear range sufficiently to remove the need for modulation, enabling higher loop speeds that are no longer limited by the speed of the modulation mirror, which contributed to the significantly improved on-sky performance. The OHP turbulence conditions (D/r0 ∼ 17 at 1400 nm) are comparable to typical Very Large Telescope (VLT) conditions (D/r0 ∼ 20), supporting the relevance of these results for VLT/RISTRETTO.

The performance measured on the PAPYRUS bench is representative of what can be expected at the VLT because the seeing conditions correspond to D/r0 ∼ 17 at 1400 nm, which is comparable to typical VLT conditions of D/r0 ∼ 20. The results indicate that the IRumPWFS is a promising candidate for the VLT/RISTRETTO instrument. p. 0

Where the paper says it

The IR-umPWFS is a strong candidate for future XAO systems: operating in the infrared extends the linear range sufficiently to remove the need for modulation, enabling higher loop speeds that are no longer limited by the speed of the modulation mirror, which contributed to the significantly improved on-sky performance. The OHP turbulence conditions (D/r0 ∼ 17 at 1400 nm) are comparable to typical Very Large Telescope (VLT) conditions (D/r0 ∼ 20), supporting the relevance of these results for VLT/RISTRETTO.

The current system performance was limited by the speed of the DM, restricting operation to approximately 1000 Hz. Further tests with a faster DM are therefore required to fully demonstrate the performance gains achievable at higher loop speeds (> 2 kHz). The integration of more advanced control algorithms, such as DD4AO and PO4AO, is expected to further enhance the overall performance and stability of the system.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Real-time control can be decoupled into independent single-stage control loops, allowing for simultaneous measurement of both visible and infrared wavefront sensor streams while controlling a single deformable mirror to improve stability.

  2. The system can achieve higher loop speeds by operating in the infrared without modulation, which is no longer limited by the speed of the modulation mirror, potentially enabling gains up to 1000 Hz instead of 500 Hz.

  3. The system can be designed to incorporate a simple global scaling factor within the loop gain to compensate for optical gains, as the optical gain can be effectively incorporated as a global scaling factor within the loop gain which we observe here.

  4. The system can achieve higher Strehl ratios and encircled energy by operating the IR-umPWFS at 1000 Hz compared to the VIS-mPWFS at 500 Hz, demonstrating higher loop speed is a major contributor to the observed gain.

  5. The system can be robust to large tip-tilt offsets up to three lambda over diameter at 1400 nm, as demonstrated by the IR-umPWFS remaining robust to tip-tilt offsets up to 3 λ/D at 1400 nm.

Abstract

Direct imaging of Earth-like exoplanets requires strong suppression of stellar light at small angular separations, achievable with extreme adaptive optics (XAO). The pyramid wavefront sensor (PWFS) is widely used for its sensitivity but suffers from nonlinearities and limited dynamic range. Modulation extends the range but reduces sensitivity and limits loop speed. We investigate an unmodulated infrared PWFS (IR-umPWFS), where the dynamic range scales with wavelength, removing the need for modulation and enabling faster operation. We adopt a 3-sided PWFS, which eliminates the roof defect of the classical 4-sided design. We assess its feasibility and performance through end-to-end simulations, lab tests, and on-sky observations on the PAPYRUS bench at the Observatoire de Haute-Provence (OHP), and compare it with a visible modulated PWFS (VIS-mPWFS). Simulations show reliable operation, reaching Strehl ratios up to 60% at 1400 nm for seeing up to 4''. Infrared operation improves linearity, reduces optical-gain variations and modal cross-talk. Laboratory results validate the simulations and confirm the pyramid quality. On sky, stable closed-loop operation was achieved over three nights. Compared with the VIS-mPWFS at 500 Hz, the IR-umPWFS at 1000 Hz showed gains of 1.63 in Strehl ratio and 1.26 in encircled energy, and a 2.03-fold reduction in residual wavefront error. The IR-umPWFS remained robust to tip-tilt offsets up to 3 lambda/D at 1400 nm. It is a strong candidate for future XAO systems: operating in the infrared extends the linear range sufficiently to remove the need for modulation, enabling higher loop speeds no longer limited by the modulation mirror, which contributed to the improved on-sky performance. The OHP turbulence (D/r0 17 at 1400 nm) is comparable to typical VLT conditions (D/r0 20), supporting the relevance of these results for VLT/RISTRETTO.

Related papers