Characterisation Methodology for Persistence and Anti-persistence in IR Detectors for the Euclid and SVOM Space Missions
Listen
Radio episode about this paper
Transcript
Introduction to the show: ident: Astrophysics. The day in astrophysics: observations, models and what the data forces.
Vera: I'm Vera.
Jocelyn: And I'm Jocelyn, here with Subrahmanyan.
Vera: We're looking at the paper: "Characterisation Methodology for Persistence and Anti-persistence in IR Detectors for the Euclid and SVOM Space Missions".
Jocelyn: Here's the gist of the paper. H2RG and ALFA are the infrared detectors used in the Euclid and SVOM space missions These types of detectors may be affected by persistence and anti-persistence, phenomena that distort pixel responses after exposure to light due to simultaneous trapping and release of charges within the pixel This article presents a universal methodology for characterising persistence and anti-persistence using differential ramps, Savitzky–Golay filtering, and non-linearity correction When applied to ground characterisation data, this approach reveals spatial inhomogeneities, environmental dependencies (in particular fluence, flux, temperature and wavelength), and unexpected spectral effects in ALFA The core of the paper is dedicated to the methodology for characterising (anti-)persistence, including data pre-processing, flux measurement, and the extraction of amplitude and current parameters This approach accounts for the diverse properties of the detectors, aiming to effectively decouple their effects from the (anti-)persistence signals in order to isolate and precisely analyse each contribution The approach consists of two major stages: firstly, a preparation of the raw data and secondly the actual extraction of (anti-)persistence parameters Data Pre-processing Steps Several pre-processing steps are applied to the raw data To mitigate the lack of data, as mentioned above, we have chosen to work with superpixels obtained by averaging 64 × 64 pixels Noise is further reduced thanks to an optimised method using reference pixels Dead and hot pixels, identified as outliers, are masked according to characterisation maps established during tests A final pre-treatment step is the conversion of ADU to electrons Signal Smoothing and Parameter Extraction Although the pre-processing significantly improves the quality of the data, the SNR of the ramp flux remains insufficient to reliably extract anti-persistence To improve the SNR, we further apply the Savitzky–Golay filter, which smooths the data while preserving its essential characteristics The resulting differential ramps reveal signatures of persistence, non-linearity, and other phenomena To study anti-persistence with minimal underestimation, a first treatment is necessary: the correction of nonlinearity After the correction, we have to extract the anti-persistence from the signal To derive the anti-persistence current, we use the same method as for persistence by taking the derivative of the resulting subtracted ramp using the Savitzky–Golay filter Observed Spatial and Environmental Dependencies The preliminary results highlight significant spatial inhomogeneities, revealing "arc-shaped or ring-shaped regions of high persistence, probably related to manufacturing defects and non-uniform trap distributions" These inhomogeneities mirror those described in the state-of-the-art literature The persistence amplitude values increase with rising temperature, particularly within the inhomogeneous zone In ALFA, an annular inhomogeneity is observed in the HE band compared to the JE band, which is unexpected since the literature mentions no wavelength dependency of persistence Fluence and Temperature Effects For fluence dependencies, persistence amplitude values are approximately three times higher in the high-persistence zone For both detectors, a linear regime is observed at low fluence, which saturates from 300 ke− The persistence current is consistent with that of the amplitude in both detectors: it increases with prior fluence and temperature, reaching a saturation threshold around 300 ke− Anti-persistence Dynamics The anti-persistence amplitude shows an increasing trend as the flux increases at low fluxes, suggesting a logarithmic or exponential function The graph of current dependencies also shows interesting results, where we observe a linear trend in this parameter as a function of flux The anti-persistence is therefore all the more difficult to extract from the ALFA detector data due to higher order non-linearities and higher reading noise The anti-persistence, although more difficult to extract, has been successfully isolated, exposing its exponential decay behaviour and correlation with non-linearity Future Work In the future, we will first finalize the method by applying non-linearity correction to all data on the H2RG and ALFA detectors Moreover, it would be interesting to redo this study with super-pixels smaller than 64x64, or even per single pixel We will also extend the anti-persistence analysis to flash illumination tests, which promise to better elucidate its dynamics Over the next year, these results will contribute to a physical model integrating all observed dependencies The model will be useful for developing flight correction strategies, ensuring that Euclid and SVOM achieve their scientific objectives with the required accuracy and reliability Acknowledgements The Euclid Consortium acknowledges the European Space Agency and a number of agencies and institutes that have supported the development of Euclid We express our gratitude to our colleagues at the CPPM (Marseille Center for Particle Physics) for their collaboration and constant support throughout this study This study was made possible thanks to CNES (National Center for Space Studies) and IN2P3 (National Institute of Nuclear and Particle Physics), which funded the current PhD thesis work References
1: Euclid Collaboration: Y.
Vera: Mellier, A.
Jocelyn: Abdurro’uf, and J.
Vera: A.
Paper summary: Vera: So we're looking at this paper by Naomie De Araujo and her team titled "Characterisation Methodology for Persistence and Anti-persistence in IR Detectors for the Euclid and SVOM Space Missions". It basically sets up a way to study these persistence and anti-persistence effects that happen in infrared detectors like H2RG and ALFA, which are used on the Euclid mission.
Jocelyn: Right. So, these phenomena distort what we measure after light hits the pixel because charges get trapped and released at the same time. This paper claims they cause biases in flux measurements and could even lead to false detections.
Subrahmanyan: That's a concern for cosmology because if these detector effects aren't understood, it messes with our dark energy and dark matter measurements one <ref:2611.02860#pg1>. The authors are presenting a universal methodology that uses differential ramps, Savitzky–Golay filtering, and non-linearity correction to characterize these effects.
Vera: Exactly. The main point is that when they test this on ground characterization data, they find spatial variations, dependencies on things like fluence, flux, temperature and wavelength in ALFA detectors.
Jocelyn: It sounds like they're showing how these detector quirks aren't just a fixed number; they depend heavily on the environment where you are observing.
Subrahmanyan: That environmental dependency is key because it means we can’t just treat these detectors as simple black boxes in our cosmological models one <ref:2611.02860#pg1>. The paper shows spatial inhomogeneities, like arc-shaped or ring-shaped regions of high persistence, which they think might be related to manufacturing defects or uneven trap distributions.
Vera: They also found that the persistence amplitude values actually increase with rising temperature, especially in those inhomogeneous zones. That's something we need to keep an eye on when planning our observations.
Jocelyn: And for ALFA specifically, they observed an annular inhomogeneity in the HE band compared to the JE band, which was actually unexpected since some literature didn't mention wavelength dependency for persistence one <ref:2611.02860#pg1>. It's a nice finding that shows how detector properties can be more complex than we initially thought.
Subrahmanyan: From a theoretical standpoint, it means our models need to incorporate these spatial and environmental variations when we try to predict the universe’s structure one <ref:2611.02860#pg1>. If the detector response changes based on where you are in space or what the local conditions are, that adds uncertainty to everything.
Vera: They also looked at fluence dependencies and found that persistence amplitude values are about three times higher in those high-persistence zones. And at low fluence, they see a linear regime before it saturates around three hundred ke minus.
Jocelyn: That saturation point sounds important for setting limits on the radiation we expect from space missions like Euclid one <ref:2611.02860#pg1>. It gives us a concrete threshold for how much light we can expect to see.
Paper summary: Subrahmanyan: If the persistence current is consistent with the amplitude, and it increases with prior fluence and temperature, reaching that saturation around three hundred ke minus, then it provides a clearer picture of how these charge trapping mechanisms scale with energy input one. This helps us build more realistic simulations for detector performance.
Vera: Moving to anti-persistence effects, the paper says the amplitude shows an increasing trend as flux increases at low fluxes, suggesting a logarithmic or exponential function. The current dependencies also show a linear trend as a function of flux for that parameter.
Jocelyn: That sounds like something tricky to measure because of those higher order non-linearities and the reading noise in ALFA data, which makes extracting the anti-persistence signal more difficult one <ref:2611.02860#pg1>. It’s harder to isolate that behavior when you have so much noise.
Subrahmanyan: The paper does successfully isolate the anti-persistence behavior, showing its exponential decay and linking it to those non-linearities we discussed earlier one <ref:2611.02860#pg1>. This connection between persistence and anti-persistence is what makes this analysis useful for understanding the underlying physics of the detectors themselves.
Vera: Looking ahead, they plan to finalize their method by applying that non-linearity correction across all data on both H2RG and ALFA detectors. They also think it would be interesting to redo the study with smaller superpixels, maybe even per single pixel.
Jocelyn: And they want to extend the anti-persistence analysis to flash illumination tests because those tests might give us better insight into its dynamics one <ref:2611.02860#pg1>. It seems like they’re building a really comprehensive picture of these detector issues.
Subrahmanyan: If they can integrate all these observed dependencies—the spatial variations, the temperature effects, and the flux relationships—into a physical model, it could be useful for developing flight correction strategies for Euclid and SVOM one <ref:2611.02860#pg1>. That would directly impact the accuracy of the scientific objectives of those missions.
Vera: So, to wrap up this paper by Naomie De Araujo et al., they developed a universal methodology to characterize persistence and anti-persistence in IR detectors using specific mathematical tools. They found that these effects are sensitive to where you are and what the local conditions like temperature or fluence are, revealing spatial structures and environmental dependencies.
Jocelyn: And their conclusion is that isolating anti-persistence is tough due to non-linearities, but they managed to capture its exponential decay and link it back to the persistence behavior. It really validates their approach for understanding these detector quirks in future missions like Euclid one <ref:2611.02860#pg1>.
Subrahmanyan: What this means for us is that we need a more robust way of modeling the instruments themselves before we rely on their data to map the universe one <ref:2611.02860#pg1>. If we can accurately correct for these detector biases, our cosmological constraints will be much tighter.
Conclusion: Vera: So, we've been looking at how these infrared detectors in Euclid and SVOM have these weird persistence and anti-persistence effects that mess up our measurements after light hits them for a while now.
Jocelyn: And this paper is about setting up a real method to figure out what those effects actually are, using differential ramps and filtering to pull out the signal.
Subrahmanyan: The authors, Naomie De Araujo and her team, they’ve done this characterization on ground data for the H2RG and ALFA detectors.
Vera: They found that these effects aren't just random noise; they show real spatial patterns based on where you are in the detector array.
Jocelyn: It also showed how much things like temperature and incoming light, or fluence, actually change the size of those persistence signals.
Subrahmanyan: This means we can’t just use a single correction factor for everything; the correction depends on where you are and what conditions you're in.
Vera: And they managed to separate out the anti-persistence behavior too, which is harder because of all that non-linearity and noise.
Jocelyn: The conclusion is that they’ve built a way to model these detector quirks so we can get more accurate data from the Euclid and SVOM missions.
Subrahmanyan: It’s important because if we don't correct for this, our cosmological models will be based on flawed input from the instruments themselves.
Vera: So, it’s about making sure that when you look at those distant galaxies, you know exactly what the detector is telling you.
Jocelyn: And they're still planning to test this method on smaller pixels and different types of light to see if it holds up under more real-world conditions.
Subrahmanyan: We’ll keep an eye on those future tests because getting a solid physical model here could really help us build better flight correction strategies for the detectors in space.
Naomie De Araujo, Aurélia Secrouna, Marie Tourneur Silvaina, Eric Kajfasz –a, Eliott Robineaua, Člioune Diopa
Centre de Physique des Particules de Marseille
astro-ph.IM
Submitted: 2026-11-02
Updated: 2026-11-02
License: http://creativecommons.org/licenses/by-nc-sa/4.0/
Importance score: 91/100
The gist: H2RG and ALFA are the infrared detectors used in the Euclid and SVOM space missions These types of detectors may be affected by persistence and anti-persistence…
Key concepts
- Persistence
- Persistence describes how the response of a detector pixel changes after being exposed to light. It involves the simultaneous trapping and release of electrical charges within the pixel structure when light hits it. This effect distorts the measured signal.
- Anti-persistence
- Anti-persistence is the opposite phenomenon, where charge dynamics in a detector response are inverted compared to persistence. Characterizing this effect is vital because it reveals further complexities in how these detectors behave under different operating conditions.
- Savitzky–Golay filtering
- This is a smoothing technique used on data signals. It helps reduce noise while preserving the essential features of the signal, such as peaks and trends. It was employed here to improve the signal-to-noise ratio for extracting persistence and anti-persistence parameters.
- Spatial Inhomogeneities
- These refer to variations in detector performance across different areas of a detector. The study found 'arc-shaped or ring-shaped regions' of high persistence, suggesting manufacturing defects or uneven trap distributions that vary spatially.
Terminology
Summary
H2RG and ALFA are the infrared detectors used in the Euclid and SVOM space missions These types of detectors may be affected by persistence and anti-persistence, phenomena that distort pixel responses after exposure to light due to simultaneous trapping and release of charges within the pixel This article presents a universal methodology for characterising persistence and anti-persistence using differential ramps, Savitzky–Golay filtering, and non-linearity correction When applied to ground characterisation data, this approach reveals spatial inhomogeneities, environmental dependencies (in particular fluence, flux, temperature and wavelength), and unexpected spectral effects in ALFA
Methodology for Characterising Effects
The core of the paper is dedicated to the methodology for characterising (anti-)persistence, including data pre-processing, flux measurement, and the extraction of amplitude and current parameters This approach accounts for the diverse properties of the detectors, aiming to effectively decouple their effects from the (anti-)persistence signals in order to isolate and precisely analyse each contribution The approach consists of two major stages: firstly, a preparation of the raw data and secondly the actual extraction of (anti-)persistence parameters
Data Pre-processing Steps
Several pre-processing steps are applied to the raw data To mitigate the lack of data, as mentioned above, we have chosen to work with superpixels obtained by averaging 64 × 64 pixels Noise is further reduced thanks to an optimised method using reference pixels Dead and hot pixels, identified as outliers, are masked according to characterisation maps established during tests A final pre-treatment step is the conversion of ADU to electrons
Signal Smoothing and Parameter Extraction
Although the pre-processing significantly improves the quality of the data, the SNR of the ramp flux remains insufficient to reliably extract anti-persistence To improve the SNR, we further apply the Savitzky–Golay filter, which smooths the data while preserving its essential characteristics The resulting differential ramps reveal signatures of persistence, non-linearity, and other phenomena To study anti-persistence with minimal underestimation, a first treatment is necessary: the correction of nonlinearity After the correction, we have to extract the anti-persistence from the signal To derive the anti-persistence current, we use the same method as for persistence by taking the derivative of the resulting subtracted ramp using the Savitzky–Golay filter
Observed Spatial and Environmental Dependencies
The preliminary results highlight significant spatial inhomogeneities, revealing arc-shaped or ring-shaped regions of high persistence, probably related to manufacturing defects and non-uniform trap distributions
These inhomogeneities mirror those described in the state-of-the-art literature The persistence amplitude values increase with rising temperature, particularly within the inhomogeneous zone In ALFA, an annular inhomogeneity is observed in the HE band compared to the JE band, which is unexpected since the literature mentions no wavelength dependency of persistence
Fluence and Temperature Effects
For fluence dependencies, persistence amplitude values are approximately three times higher in the high-persistence zone For both detectors, a linear regime is observed at low fluence, which saturates from 300 ke− The persistence current is consistent with that of the amplitude in both detectors: it increases with prior fluence and temperature, reaching a saturation threshold around 300 ke−
Anti-persistence Dynamics
The anti-persistence amplitude shows an increasing trend as the flux increases at low fluxes, suggesting a logarithmic or exponential function The graph of current dependencies also shows interesting results, where we observe a linear trend in this parameter as a function of flux The anti-persistence is therefore all the more difficult to extract from the ALFA detector data due to higher order non-linearities and higher reading noise The anti-persistence, although more difficult to extract, has been successfully isolated, exposing its exponential decay behaviour and correlation with non-linearity
Future Work
In the future, we will first finalize the method by applying non-linearity correction to all data on the H2RG and ALFA detectors Moreover, it would be interesting to redo this study with super-pixels smaller than 64x64, or even per single pixel We will also extend the anti-persistence analysis to flash illumination tests, which promise to better elucidate its dynamics Over the next year, these results will contribute to a physical model integrating all observed dependencies The model will be useful for developing flight correction strategies, ensuring that Euclid and SVOM achieve their scientific objectives with the required accuracy and reliability
Acknowledgements
The Euclid Consortium acknowledges the European Space Agency and a number of agencies and institutes that have supported the development of Euclid We express our gratitude to our colleagues at the CPPM (Marseille Center for Particle Physics) for their collaboration and constant support throughout this study This study was made possible thanks to CNES (National Center for Space Studies) and IN2P3 (National Institute of Nuclear and Particle Physics), which funded the current PhD thesis work
References
[1] Euclid Collaboration: Y. Mellier, A. Abdurro’uf, and J. A. Acevedo Barroso et al. Euclid: I overview of the Euclid mission
[2] Euclid Collaboration: K. Jahnke, W. Gillard, and M. Schirmer et al. Euclid: Iii the nisp instrument
[3] F. Fortin, J. L. Atteia, and A. Nouvel de la Fleche et al. Detecting the near-infrared afterglows of highredshift gamma-ray bursts using CAGIRE
[4] S. Conseil and B. Kubik Euclid - persistence in-flight calibration
[5] R. Laureijs, P. Gondoin, and L. Duvet et al. Euclid: ESA’s mission to map the geometry of the dark universe
[6] A. Rogalski HgCdTe infrared detector material: history, status and outlook
[7] P. Norton HgCdTe infrared detectors
[8] O. Gravrand, C. Lobre, and J.-L. Santailler et al. Fabrication and characterization of a high performance NIR 2kx2k MCT array at CEA and Lynred for astronomy applications
[9] J. Le Graet, A. Secroun, and M. Tourneur-Silvain et al. p. 0 Characterisation Methodology of Persistence and
Anti-Persistence in IR Detectors for the Euclid and SVOM
Space Missions∗
Naomie De Araujo a
, Aur´elia Secrouna
, Marie Tourneur Silvaina
, Eric Kajfasz ´ a
, Eliott
Robineaua
, and Alioune Diopa
aCentre de Physique des Particules de Marseille, Marseille, France
ABSTRACT
H2RG and ALFA are the infrared detectors used in the Euclid and SVOM space missions. These types of
detectors may be affected by persistence and anti-persistence, phenomena that distort pixel responses after
exposure to light due to simultaneous trapping and release of charges within the pixel. Characterisation Methodology of Persistence and
Anti-Persistence in IR Detectors for the Euclid and SVOM
Space Missions∗
Naomie De Araujo a
, Aur´elia Secrouna
, Marie Tourneur Silvaina
, Eric Kajfasz ´ a
, Eliott
Robineaua
, and Alioune Diopa
aCentre de Physique des Particules de Marseille, Marseille, France
ABSTRACT
H2RG and ALFA are the infrared detectors used in the Euclid and SVOM space missions. These types of
detectors may be affected by persistence and anti-persistence, phenomena that distort pixel responses after
exposure to light due to simultaneous trapping and release of charges within the pixel.Where the paper says it
Where the paper says it
[10] A Nouvel de la Fleche, J.-L. Atteia, and J. Boy et al. CAGIRE: a wide-field NIR imager for the COLIBRI 1. p. 1 The SVOM mission aims to detect and study gamma-ray bursts (GRBs) and other high-energy transient
phenomena to probe the extreme Universe. This is made possible by instruments such as the CAGIRE camera,
featuring the ALFA detector, enabling wide-field observations in the near-infrared domain [3].Where the paper says it
[11] B Hilbert Updated non-linearity calibration method for WFC3/IR WFC3 Instrument Science Report 2014-17 Space Telescope Science Institute Baltimore, MD, 2014
[12] Euclid Collaboration: B. Kubik, R. Barbier, and J.-C. Cl´emens et al. Euclid preparation: LXXX overview of Euclid infrared detector performance from ground tests
[13] M.R. Baril Characterization of persistence in WIRCam’s Hawaii 2-RG arrays SPIE Digital Library, pages 100–120, 2008
[14] T. Biesiadzinski, W. Lorenzon, and R. Newman et al. Reciprocity failure in HgCdTe detectors: Measurements and mitigation Publications of the Astronomical Society of the Pacific, 123:958–963, August 2011
[15] S. M. Tulloch and E. M. George Predictive model of persistence in H2RG detectors 2019 arXiv:1908. p. 2 It would thus be suitable to work with a more accurate model of persistence,
describing both its temporal and spatial behaviour, as well as its environmental dependencies. In this context, we investigate the persistence effects associated with two space missions, Euclid and SVOM [3],
for which the CPPM is responsible for characterising their infrared detectors.Where the paper says it
[16] B Serra Caracterisation des detecteurs infrarouges de la mission spatiale Euclid: etude des performances des detecteurs infrarouges H2RG PhD thesis, 2016
[17] T. Legoff Etude de la persistance dans les retines proches IR en HgCdTe pour les applications en astronomie PhD thesis, 2022
[18] Space Telescope Science Institute Non-ideal detector effects Roman Space Telescope Documentation 2026 Roman Space Telescope Documentation
[19] C. Fazar, C. Darren Dowell, and B.P. Crill et al. Image persistence flagging for spherex In Journal of Astronomical Telescopes, Instruments, and Systems, Vol 11 Issue 1 Society of Photo-Optical Instrumentation Engineers (SPIE) Conference Series SPIE January 2025
[20] R.M. Smith, M. Zavodny, G. Rahmer, and M. Bonati A theory for image persistence in HgCdTe photodiodes In High Energy Optical and Infrared Detectors for Astronomy III volume 7021 of Proc of SPIE, 2008
[21] K. S. Long, S. M. Baggett, and J. W. MacKenty Characterizing persistence in the WFC3 IR channel Finite trapping times WFC3 Instrument Science Report 2013
[22] B Serra, A Secroun, and J.-C. Clemens et al. Characterization of Euclid-like H2RG IR detectors for the NISP instrument In H. p. 8 Knowing these spatial variations is essential for applications like Euclid, where pixel-to-pixel uniformity is
important for photometry and high-precision spectroscopy. The Euclid NISP detector team has also mapped the
persistence on the 16 H2RG detectors of the Euclid mission, revealing significant spatial inhomogeneities [29].Where the paper says it
[23] T. Le Goff, T. Pichon, and N. Baier et al. Model and characterization of persistence in HgCdTe SWIR detectors for astronomy application Journal of Electronic Materials, 2022
[24] D Ives, D Alvarez, and N Bezawada et al. Characterisation, performance, and operational aspects of the H4RG-15 near infrared detectors for the MOONS instrument 2020 arXiv:2012. p. 7 Only the first case is observed in the literature [23]. Temperature Regarding the temperature dependency, the ESO team working on the H4RG detectors for
the MOONS instrument [24] distinguish three different behaviours based on temperature.Where the paper says it
[25] S Tulloch Persistence characterization of Teledyne H2RG detectors 2018 arXiv:1807.05217
[26] G Mosby, B. Rauscher, and C Bennett Properties and characteristics of the nancy grace roman space telescope H4RG-10 detectors Journal of Astronomical Telescopes, Instruments, and Systems 6(4):046001, 2020
[27] H Rousset, N. Baier, and D. S Giao Extraction of traps parameters in HgCdTe P/N MWIR focal plane arrays using photocurrent transients induced by optical excitation Journal of Electronic Materials, 2024
[28] R.E Anderson, M Regan, J Valenti, and E Bergeron Understanding persistence: A 3d trap map of an H2RG imaging sensor 2014 arXiv:1402.4181
[29] B Kubik, R. Barbier, and G Smadja Performance of the image persistence model for Euclid infrared detectors In A D Holland and K Minoglou editors X-Ray Optical and Infrared Detectors for Astronomy XI volume 13103 of Society of Photo-Optical Instrumentation Engineers (SPIE) Conference Series page 1310315 SPIE August 2024
[30] A Nouvel de la Fl´eche, J.-L. Atteia, and H Valentin Flux reconstruction for the NIR camera CAGIRE at the focus of the COLIBRI telescope In A. p. 1 This is made possible by instruments such as the CAGIRE camera,
featuring the ALFA detector, enabling wide-field observations in the near-infrared domain [3]. In recent years, MCT CMOS infrared (IR) detectors have been increasingly used in both space missions
and ground-based telescope instrumentation.Where the paper says it
[31] J. Le Gra¨et, A. p. 8 This allows comparisons between detectors
with different gain values, and expresses data into interpretable physical units. For this conversion, gain maps
produced by Jean Le Gra¨et are applied to the pre-processed data [31].Where the paper says it
[32] P.W. Oxby An optimal weighting function for the Savitzky-Golay filter 2021 arXiv:2111. p. 9 Thanks to the use of superpixels and the averaging of
ramps acquired under identical conditions, these errors are mitigated. To account for errors during smoothing3
,
we have recoded an error-weighted Savitzky–Golay filter function, based on several articles on the subject [32, 33].Where the paper says it
[33] P.W. Oxby Confidence intervals for the Savitzky-Golay filter with an application to the Keeling data for atmospheric CO2 2021 arXiv:2412. p. 9 For our example of Fig. 3, we have compared SNRs before and after the application of the Savitzky–Golay
filter.Where the paper says it
[34] A Secroun, B Serra, and J.-C. Cl´emens et al. Characterization of h2rg ir detectors for the euclid nisp instrument In Andrew D Holland and James Beletic editors High Energy Optical and Infrared Detectors for Astronomy VII volume 9915 of Society of Photo-Optical Instrumentation Engineers (SPIE) Conference Series page 99151Y July 2016
[35] A Secroun, R. Barbier, and Buton et al. Euclid flight H2RG IR detectors: per pixel conversion gain from onground characterization for the Euclid NISP instrument In Andrew D Holland and James Beletic editors High Energy Optical and Infrared Detectors for Astronomy VIII volume 10709 of Society of Photo-Optical Instrumentation Engineers (SPIE) Conference Series page 1070921 July 2018
[36] A Secroun, B Serra, and J.-C. Cl´emens et al. Characterization of h2rg ir detectors for the euclid nisp instrument In Andrew D Holland and James Beletic editors High Energy Optical and Infrared Detectors for Astronomy VII volume 9915 of Society of Photo-Optical Instrumentation Engineers (SPIE) Conference Series page 99151Y July 2016
[37] A Secroun, R. Barbier, and Buton et al. Euclid flight H2RG IR detectors: per pixel conversion gain from onground characterization for the Euclid NISP instrument In Andrew D Holland and James Beletic editors High Energy Optical and Infrared Detectors for Astronomy VIII volume 10709 of Society of Photo-Optical Instrumentation Engineers (SPIE) Conference Series page 1070921 July 2018
[38] A Secroun, B Serra, and J.-C. Clemens et al. Characterization of h2rg ir detectors for the euclid nisp instrument In Andrew D Holland and James Beletic editors High Energy Optical and Infrared Detectors for Astronomy VII volume 9915 of Society of Photo-Optical Instrumentation Engineers (SPIE) Conference Series page 99151Y July 2016
[39] A Secroun, R. Barbier, and Buton et al.
Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.
Improvements for AI systems
-
Evaluation of persistence effects in ground characterization data can reveal spatial inhomogeneities, environmental dependencies (in particular fluence, flux, temperature and wavelength), and unexpected spectral effects in ALFA. This validates the method for developing
in-flight correction models capable of meeting the missions’ accuracy requirements.
-
The proposed methodology allows for the extraction of fundamental dependencies of persistence such as flux, temperature, and wavelength from ground-based datasets to establish a pixel response model incorporating both persistence and anti-persistence. This enables the development of a model capable of
describing the behaviour of (anti-)persistence.
-
The system can perform signal processing using differential ramps and Savitzky–Golay filtering to isolate transient effects like persistence and non-linearity, improving the visibility and quantifiability of these phenomena. This approach allows for
the subtraction of components evolving at a constant rate – such as dark current – during fixed-temperature acquisitions.
-
The AI system can quantify environmental dependencies by analyzing persistence amplitude and current as a function of temperature, fluence, and wavelength across different detector types (H2RG and ALFA). This provides data to design
a new test plan to explore additional parameter values
for future characterization. -
The system can extract anti-persistence parameters by correcting for non-linearity using a decomposition into orthogonal polynomials, applying these corrections within the defined dynamic range of 15 k to 50 ke−. This allows for the extraction of
the dynamics of charge trapping at the beginning of the acquisition.
Abstract
H2RG and ALFA are the infrared detectors used in the Euclid and SVOM space missions. These types of detectors may be affected by persistence and anti-persistence, phenomena that distort pixel responses after exposure to light due to simultaneous trapping and release of charges within the pixel. These phenomena have shown to cause biases in flux measurements and potentially false detections, among other effects. This article presents a universal methodology for characterising persistence and anti-persistence using differential ramps, Savitzky--Golay filtering, and non-linearity correction. When applied to ground characterisation data, this approach reveals spatial inhomogeneities, environmental dependencies (in particular fluence, flux, temperature and wavelength), and unexpected spectral effects in ALFA. These preliminary results validate the method and pave the way for in-flight correction models capable of meeting the missions' accuracy requirements.
Sources
- Predictive model of persistence in H2RG detectors
- Characterisation, performance, and operational aspects of the H4RG-15 near infrared detectors for the MOONS instrument
- Persistence Characterisation of teledyne H2RG detectors
- Understanding Persistence: A 3D Trap Map of an H2RG Imaging Sensor
- An Optimal Weighting Function for the Savitzky-Golay Filter
- Confidence Intervals for the Savitzky-Golay Filter with an Application to the Keeling Data for Atmospheric CO2
Related papers
- On-sky demonstration of a vector Zernike wavefront sensor in a cascaded adaptive optics system
- Euclid Data Release 1 (DR1): Calibration strategy and observations
- The General Antiparticle Spectrometer (GAPS) Antarctic Balloon Payload
- Detection and excision of radio-frequency interference in radio arrays
- Unified matched-filter and excess-power pipeline for gravitational-wave detector characterization
- Ushering in sub-arcsecond angular resolution observatories in the far-infrared: The case for a double-Fourier interferometer