Reactor operation induced thermal effects on neutron flux measurements using cubed He neutron detectors at a TRIGA Mk II research reactor

arXiv:2606.21744 · physics.ins-det · Submitted 2026-06-19 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: We're looking at the paper: "Reactor operation induced thermal effects on neutron flux measurements using cubed He neutron detectors at a TRIGA Mk II research reactor".

Mira: Here's the gist of the paper. A variation of the measured neutron flux using 3He detectors at a TRIGA Mk II nuclear research reactor during steady-state operation is reported in this article The observed effect shows a statistically significant anti-correlation (> 7 σ) between the temperature in the reactor pool and recorded neutron count rates Following reactor start-up under nominal operating conditions, the effect occurs for a specific time period until both thermal equilibrium and a constant neutron count rate are reached Observed Phenomenon The study reports that during neutron count rate measurements over the period of a full reactor day, 7 h, a statistically significant (> 7 σ) reduction of the count rate of up to 3.697(6) % (depending on the measurement location and operating conditions) at nominal 250 kW operation over a duration of about 2.0 h to 2.5 h after the reactor start-up was observed Simultaneous neutron and temperature measurements were performed in different configurations around the reactor in order to gain qualitative insights about the temperature dependent count rate behavior The authors discovered an apparent anti-correlation between the count rate and temperature, with the count rate decreasing with increasing temperature Experimental Setup Details The TRIGA reactor at TU Wien has a pool diameter of 1.98 m and a depth of 6.2 m, with a graphite reflector located 0.61 m above the bottom of the reactor tank The measurements were performed at the tangential beam tube (Figure 3), a radial beam tube (Figure 5), the irradiation room (Figure 4) and thermal column (Figure 6) Neutron measurements were performed using a VacuTec type 70 063 He-filled gas proportional neutron detector Temperature measurements were carried out using a Calex Excelog 6 temperature data logger in combination with RS PRO Type K thermocouples Analysis of Correlation and Significance The Pearson correlation coefficient for the case without cooling was r = −0.9914, with a p-value of p = 6.312 × 10−21, which corresponds to a significance of more than 9 σ The neutron count rate and temperature data has been fitted with f(t) = ae−bt+c for all runs, except the ones at the thermal column, the tangential beam tube with 100 kW, and the irradiation room with 5 kW, for which f(t) = kt + d was used The R2-values obtained show R2 n = 0.9880 and R2 T = 0.9995 for the tangential beam tube at 100 kW without cooling Spatial Dependence of the Effect The effect is shown to occur at all beam tubes reactor-wide, with the exception of the thermal column The absence of the correlation at the thermal column could be explained by its significantly different construction compared to other beam tubes The measurements at the irradiation room with a reactor power of 5 kW without cooling show a constant (within the margins of error) neutron count rate and a slight temperature increase of ∆T < 1 K≈ 0.

Paper summary: Kai: So, to wrap up on this paper "Reactor operation induced thermal effects on neutron flux measurements using cubed He neutron detectors at a TRIGA Mk II research reactor," what's the main point they are driving home? It’s that reactor heat and temperature directly influence how neutrons are counted in these specific detectors during startup.

Mira: Exactly. The thesis is that there is a statistically significant anti-correlation, greater than seven sigma, between the pool temperature and the neutron count rates observed over a certain time frame after reactor start-up under normal operating conditions one <ref:2606.21744#pg3>.

Lev: For us building error correction for real hardware, what this means practically is that you need to incorporate a correction for this thermal effect during the initial phase of operation until thermal equilibrium and a steady count rate are established one <ref:2606.21744#pg3>.

Kai: It also matters spatially. They showed this effect happens across all beam tubes except for the thermal column, and they explain that difference lies in how those specific detector constructions are built one <ref:2606.21744#pg3>.

Mira: So, in simple terms, the paper shows that for high precision work at TRIGA reactors, you can't treat temperature and neutron count rate as completely independent variables during startup; you have to account for this observed relationship one <ref:2606.21744#pg3>.

Lev: The authors also flagged their limitation: they didn't fully investigate the physical mechanism causing this effect, so future experiments should focus on identifying that root cause one <ref:2606.21744#pg3>.

Kai: It’s a solid piece of data showing how operational conditions introduce subtle, measurable dependencies in detector output.

Mira: It highlights the need for careful modeling when you are setting up precise measurements in these types of nuclear environments one <ref:2606.21744#pg3>.

Conclusion: Kai: So, to sum up this paper, they’re looking at how heat from a running reactor messes with the neutron counts when you use these specific gas detectors inside them.

Mira: It’s about a TRIGA reactor and those He detectors, which means we're talking about the physical interaction between high temperature in the pool and how many neutrons you actually measure coming out of that setup.

Lev: From my side, this is interesting because it shows a measurable effect during startup—not just some random noise—until things settle down into a steady state.

Kai: Exactly. They found a statistically significant drop in the count rate, up to about three point seven percent depending on where you measured it, when the temperature was increasing over that first couple of hours after starting up.

Mira: What they’re really pointing out is this anti-correlation; as the reactor gets warmer, the neutron count rate goes down significantly during that initial phase. They found a Pearson correlation coefficient of negative zero point nine nine one four with a p value way smaller than that means it's definitely not random.

Lev: And for us building error correction, that's a real problem because if you don’t subtract this thermal effect, your correction won’t work properly during those first two or three hours of operation.

Kai: Right. They did look at the setup in different places around the reactor—the beam tubes and even the irradiation room—and they found it happened everywhere except for one specific spot called the thermal column.

Mira: That spatial difference is important because it suggests that the construction of that particular detector or its immediate environment is what makes it immune to this temperature dip, which we have to keep in mind when thinking about general reactor monitoring.

Lev: It’s a good reminder that when you design error correction for real hardware, you can't just assume everything behaves the same way across the entire facility; there are localized physical differences you need to model.

Kai: So, while it’s just a TRIGA reactor experiment now, this kind of thermal dependence is something we have to consider when scaling up measurements in any high-heat environment, whether it's a reactor or a particle accelerator.

Mira: It gives us a concrete example of how operational physics—the heat transfer—directly impacts the fundamental measurement tools used to monitor nuclear processes.

Lev: And looking ahead, we need to figure out the physical mechanism behind this anti-correlation so we can build better, more accurate models for when we actually try to run these kinds of experiments on real hardware.

Sebastian Dorer, Clemens Trunner, Robert Bergmann, Dieter Hainza, Erwin Jericha, Stephan Sponar, Thomas Stummerb

Atominstitut, Technische Universität Wien

physics.ins-det

Submitted: 2026-06-19

Updated: 2026-09-15

DOI: 10.1016/j.nucengdes.2026.115305

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 78/100

The gist: A variation of the measured neutron flux using 3He detectors at a TRIGA Mk II nuclear research reactor during steady-state operation is reported in this article The observed effect shows a…

Key concepts

Anti-correlation
This means two variables move in opposite directions. In this context, it means that when the reactor pool temperature goes up, the recorded neutron count rate tends to go down. The study found this relationship was strong and statistically significant.
Neutron Count Rate
This is a measurement of how many neutrons are detected by the 3He detectors over a specific period. It is a key indicator of the reactor's current neutron activity or power output, which the researchers were trying to measure against temperature changes.
Statistical Significance (7 $\sigma$)
This term indicates that the observed relationship between temperature and count rate is highly unlikely to be due to random chance. A significance level of greater than 7 standard deviations means there is a very high degree of confidence that the anti-correlation found is a real physical effect.
Thermal Equilibrium
This refers to the point where the temperature inside the reactor pool stops changing significantly over time. The study noted that this anti-correlation effect only lasted for a specific period until this thermal equilibrium was reached.

Terminology

Summary

A variation of the measured neutron flux using 3He detectors at a TRIGA Mk II nuclear research reactor during steady-state operation is reported in this article The observed effect shows a statistically significant anti-correlation (> 7 σ) between the temperature in the reactor pool and recorded neutron count rates Following reactor start-up under nominal operating conditions, the effect occurs for a specific time period until both thermal equilibrium and a constant neutron count rate are reached

Observed Phenomenon

The study reports that during neutron count rate measurements over the period of a full reactor day, 7 h, a statistically significant (> 7 σ) reduction of the count rate of up to 3.697(6) % (depending on the measurement location and operating conditions) at nominal 250 kW operation over a duration of about 2. p. 0

Where the paper says it

Thereby, during neutron count rate measurements over the period of a full reactor day, 7 h, a statistically significant (> 7 σ) reduction of the count rate of up to 3. 697(6) % (depending on the measurement location and operating conditions) at nominal 250 kW operation over a duration of about 2.

0 h to 2.5 h after the reactor start-up was observed Simultaneous neutron and temperature measurements were performed in different configurations around the reactor in order to gain qualitative insights about the temperature dependent count rate behavior The authors discovered an apparent anti-correlation between the count rate and temperature, with the count rate decreasing with increasing temperature

Experimental Setup Details

The TRIGA reactor at TU Wien has a pool diameter of 1.98 m and a depth of 6. p. 1

Where the paper says it

The reactor pool has a diameter of 1. 98 m and a depth of 6.

2 m, with a graphite reflector located 0. p. 1
Where the paper says it

A further, newly introduced function of the graphite reflector in the TRIGA Mk II design is its use as an additional moderator for the beam tubes. 2 TRIGA Mark II Vienna The TRIGA reactor located in Vienna and operated by the TRIGA Center Atominstitut of TU Wien is a TRIGA Mark II design.

61 m above the bottom of the reactor tank The measurements were performed at the tangential beam tube (Figure 3), a radial beam tube (Figure 5), the irradiation room (Figure 4) and thermal column (Figure 6) Neutron measurements were performed using a VacuTec type 70 063 He-filled gas proportional neutron detector Temperature measurements were carried out using a Calex Excelog 6 temperature data logger in combination with RS PRO Type K thermocouples

Analysis of Correlation and Significance

The Pearson correlation coefficient for the case without cooling was r = −0.9914, with a p-value of p = 6. p. 4

Where the paper says it

For the case without cooling, the calculated Pearson correlation coefficient [43] is r = −0. 9914, with a p-value of p = 6.

312 × 10−21, which corresponds to a significance of more than 9 σ The neutron count rate and temperature data has been fitted with f(t) = ae−bt+c for all runs, except the ones at the thermal column, the tangential beam tube with 100 kW, and the irradiation room with 5 kW, for which f(t) = kt + d was used The R2-values obtained show R2 n = 0. p. 4
Where the paper says it

The neutron count rate and temperature data has been fitted with f(t) = ae−bt+c for all runs, except the ones at the thermal column, the tangential beam tube with 100 kW, and the irradiation room with 5 kW, for which f(t) = kt + d was used. The results listed in Table 1 show that the values of b for different measurement positions are remarkably similar.

9880 and R2 T = 0. p. 4
Where the paper says it

The obtained R2 -values are R2 n = 0. 9880 and R2 T = 0.

9995 for the tangential beam tube at 100 kW without cooling

Spatial Dependence of the Effect

The effect is shown to occur at all beam tubes reactor-wide, with the exception of the thermal column The absence of the correlation at the thermal column could be explained by its significantly different construction compared to other beam tubes The measurements at the irradiation room with a reactor power of 5 kW without cooling show a constant (within the margins of error) neutron count rate and a slight temperature increase of ∆T < 1 K≈ 0.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Automated detection of statistically significant anti-correlation between reactor pool temperature and neutron count rates during steady-state operation using Pearson correlation coefficient calculations for different measurement locations. This allows AI systems to identify potential thermal effects in real-time data streams from reactor monitoring equipment.

  2. Development of a predictive model based on the exponential fit f(t) = ae-bt+c to forecast the temporal behavior of neutron count rates following reactor start-up under various power levels and cooling conditions. This capability enables AI to anticipate deviations from nominal operation before they become critical issues for high precision experiments.

  3. Implementation of a multi-parameter analysis framework that incorporates both time-dependent decay constants (b) and linear drift constants (k) for neutron count rates, allowing the AI to distinguish between transient effects and steady-state temperature dependencies across different experimental setups. This improves the ability of AI to isolate the root cause of flux reduction in complex coupled thermal systems.

  4. Creation of a configuration-dependent effect classifier that determines whether a measured anti-correlation is reactor-wide or specific to certain components, such as distinguishing between beam tubes and the thermal column based on correlation strength (r values). This aids AI in prioritizing necessary corrections for high precision experiments by identifying the most relevant physical dependencies.

  5. Integration of simulation coupling with CFD calculations to validate observed temporal behaviors against theoretical predictions for neutron flux and temperature distribution within different reactor geometries. This allows AI systems to use established models like TRIPOLI-4 or OpenMC to interpret experimental anomalies more accurately than relying solely on empirical data fitting.

Abstract

A variation of the measured neutron flux using cubed He detectors at a TRIGA Mk II nuclear research reactor during steady-state operation is reported in this article. The observed effect shows a statistically significant anti-correlation (> 7,σ) between the temperature in the reactor pool and recorded neutron count rates. Following reactor start-up under nominal operating conditions, the effect occurs for a specific time period until both thermal equilibrium and a constant neutron count rate are reached. Simultaneous neutron and temperature measurements are performed in different configurations around the reactor in order to gain qualitative insights about the temperature dependent count rate behavior.

Related papers