Ultra-low loss piezo-optomechanical low-confinement silicon nitride platform for visible wavelength quantum photonic circuits

arXiv:2603.02584 · physics.optics, quant-ph · Submitted 2026-03-03 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: We're looking at the paper: "Ultra-low loss piezo-optomechanical low-confinement silicon nitride platform for visible wavelength quantum photonic circuits".

Title and authors: Kai: So we're looking at this paper today, "Ultra-low loss piezo-optomechanical low-confinement silicon nitride platform for visible wavelength quantum photonic circuits." It’s about building the actual hardware that we need for scalable quantum computing.

Mira: Yeah, the focus here is on solving a big problem: getting ultra-low loss while still having the fast, low-power reconfiguration needed for these systems. The authors are combining two things: low-confinement silicon nitride waveguides with piezooptomechanical actuation.

Lev: From my side, I’m wondering if this platform is actually manufacturable at scale. We've seen promises before from AlN based platforms, so the real question is whether this Si3N4 approach holds up in terms of integration and reliability for real hardware.

Kai: Exactly, Lev. What they’re showing here with silicon nitride waveguides gives us that low loss performance we need at seven hundred eighty nanometers, which is right in that visible wavelength quantum regime where many important components live.

Mira: And the authors are pushing the limits on how much of a circuit you can fit into that tiny footprint while keeping the loss down. It sounds like they are tackling the fundamental trade-off between confinement and efficiency.

Lev: I'm paying close attention to how they define their metrics, especially things like propagation loss in decibels per meter and the voltage length product, because those are what we actually need to calculate overhead on a real chip.

The paper's summary: Kai: Okay, so the paper lays out a platform that achieves two point six dB per meter of propagation loss at seven hundred eighty nanometers using this silicon nitride setup and piezooptomechanical control. They also report a megahertz-scale modulation bandwidth, which is pretty fast for visible light applications.

Mira: And they’re not just reporting the loss; they are showing how they integrate thermo-optic modulators and PZT actuators with the low-confinement silicon nitride waveguides, and it seems both approaches have some significant limitations that this new combination tries to overcome.

Lev: From an error correction standpoint, I'm interested in how this translates to a functional circuit. They mention reconfigurable Mach–Zehnder interferometers where you get zero point six three dB loss per spiral phase shifter, which is important information for calculating the total loss budget of a larger processor.

Kai: And they show that this setup has negligible hysteresis, which is a huge deal because hysteresis messes up your control and stability in these kinds of devices. It’s not just about the static performance; it’s about how well it reconfigures dynamically.

Mira: I think the main point is that this combination offers a way to get deep, actively reconfigurable quantum photonic circuits at visible wavelengths, which is exactly what we want for on-chip quantum memories and routers. It moves us away from just using high-confinement platforms because their losses are too high for scaling.

Lev: I'm still digging into the numbers they give on the voltage length product, that two point eight V·m they quote is a key figure to compare against other modulator platforms we're developing <ref:2603.02584#pg1>.

The paper's improvements: Kai: The authors spend some time optimizing their design parameters to get better results, and they show that by leveraging strain-induced optical path length modulation through selective release of sections in the spiral phase shifters, they can reduce that voltage length product by a factor of five to ten times compared to current devices.

Mira: That reduction is significant because it means the voltage loss product could potentially drop down to around four V per decibel or even lower, which would drastically improve the overall efficiency of their quantum operations.

Lev: If you can reduce that metric by that much, it directly impacts the required power budget for driving those actuators and modulators in a larger system. It makes running the hardware much more feasible on existing cryogenic setups.

Kai: And they determine an optimal geometry for minimum voltage length product with silicon nitride piezo-optic coefficients of p11 equals negative zero point one two five and p12 equals zero point zero four seven, converging on a final voltage length product of two point three V·m with a core width of one micrometer.

Mira: That convergence helps you understand which material effects are dominant; they find that silicon dioxide dominates the strain-induced change, while silicon nitride contributes an opposing effect. It’s a nuanced piece of material science happening right at the heart of the device.

Lev: I like that they mapped out exactly what causes the excess loss; they identified scattering loss at the cladding–metal interface as the main culprit, and calculated that this is in the order of ten to the minus twenty-second decibels per meter, which is basically negligible across all roughness parameters considered.

Conclusion: Kai: So, to wrap up this paper on "Ultra-low loss piezo-optomechanical low-confinement silicon nitride platform for visible wavelength quantum photonic circuits," we see a system that offers ultra-low propagation loss of two point six dB per meter and good modulation bandwidth.

Mira: And the main thing is the improvement in performance potential when you optimize the geometry, getting that voltage length product down to around two point three V·m and achieving those gains in quantum state generation efficiency.

Lev: For me, it means we have a concrete target for what a functional component based on this architecture could actually look like when we factor in real-world error correction overhead and power consumption.

Kai: And for the next steps, it points toward using this low-loss, scalable architecture as the essential backbone for building quantum routers and universal quantum photonic logic circuits.

Mira: It’s a path to seamless integration of single-photon sources, modulators, and electronic control on a single chip because of that anneal-free fabrication process.

Lev: I just want to say that this platform gives us the hardware foundation we need to start designing the actual systems for quantum networking, assuming these material properties hold up under longer operational periods.

Mayank Mishra, Gwangho Choi, Wenhua He, Gina M. Talcott, Katherine Kearney, Michael Gehl, Andrew Leenheer, Daniel Dominguez

James C Wyant College of Optical Sciences, University of Arizona, Tucson, Arizona and Microsystems Engineering Science and Applications Sandia National Laboratories Albuquerque, New Mexico and Electrical Computer and Energy Engineering University of Colorado Boulder

physics.optics, quant-ph

Submitted: 2026-03-03

Updated: 2026-08-27

Journal ref: Nature Communications (2026)

DOI: 10.1038/s41467-026-77969-0

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 89/100

The gist: Realizing photonic quantum computing at scale requires integrated circuits that combine ultra-low loss with fast, low-power, low-hysteresis, and low-crosstalk reconfiguration.

Key concepts

Low-confinement silicon nitride waveguides
These are optical pathways made from silicon nitride that are designed to have very low signal loss. They allow high optical power handling and a wide range of light wavelengths to pass through efficiently, which is crucial for building scalable quantum circuits.
Piezooptomechanical actuation
This technique uses piezoelectric materials that change shape when an electric voltage is applied. When integrated with the waveguide, this allows precise control over the optical path length, enabling fast and low-hysteresis reconfiguration of the circuit's properties.
Voltage–Loss Product (VLP)
The VLP is a single metric used to evaluate modulator performance by combining voltage and loss. Minimizing this product helps optimize the design, balancing the electrical control required to change the light path against minimizing unwanted signal attenuation.

Terminology

Summary

Realizing photonic quantum computing at scale requires integrated circuits that combine ultra-low loss with fast, low-power, low-hysteresis, and low-crosstalk reconfiguration. p. 0

Where the paper says it

Eichenfield@colorado. edu; Abstract Realizing photonic quantum computing at scale requires integrated circuits that combine ultra-low loss with fast, low-power, low-hysteresis, and low-crosstalk reconfiguration.

Low-confinement silicon nitride waveguides offer the requisite loss performance. p. 0
Where the paper says it

These requirements are particularly challenging at visible wavelengths, where many quantum resource-state generators, including single-photon sources and quantum memories, naturally operate. Low-confinement silicon nitride waveguides offer the requisite loss performance, but conventional thermooptic modulators dissipate significant static power, driving thermal crosstalk and precluding cryogenic operation.

This work combines piezooptomechanical actuation with a CMOS-foundry-fabricated, low-confinement silicon nitride platform, achieving 2. p. 0
Where the paper says it

Visible-wavelength piezo-optomechanical circuits avoid these drawbacks, but existing demonstrations rely either on high-confinement waveguides with propagation losses of 35–100 dB/m, or on lowconfinement platforms using foundry-incompatible PZT. Here we combine piezooptomechanical actuation with a CMOS-foundry-fabricated, low-confinement silicon nitride platform, achieving 2.

6 dB/m propagation loss at 780 nm, megahertz-scale modulation bandwidth, a half-wave voltage-length product of 2. p. 0
Where the paper says it

Here we combine piezooptomechanical actuation with a CMOS-foundry-fabricated, low-confinement silicon nitride platform, achieving 2. 6 dB/m propagation loss at 780 nm, megahertz-scale modulation bandwidth, a half-wave voltage-length product of 2.

8 V·m, and negligible hysteresis. p. 0
Where the paper says it

6 dB/m propagation loss at 780 nm, megahertz-scale modulation bandwidth, a half-wave voltage-length product of 2. 8 V·m, and negligible hysteresis.

Platform Advantages

Low-confinement silicon nitride waveguides provide ultra-low propagation losses. These platforms deliver high optical power-handling capabilities and a wide transparency window. p. 1

Where the paper says it

1 dB/m [15, 16] at telecommunication wavelengths and below 1 dB/m [17, 18] at visible wavelengths. These low-confinement waveguide platforms deliver high optical power-handling capabilities and a wide transparency window [19, 20].

The integration of thermo-optic modulators and PZT-based piezooptomechanical actuators with low-confinement silicon nitride waveguides has been demonstrated, but both approaches exhibit significant limitations. p. 1
Where the paper says it

Furthermore, they support the realization of ultra-high-Q resonators [21] and provide a pathway for integration with quantum systems, including rubidium atoms [22], strontium atoms [23], and InAs quantum dots [24]. The integration of thermo-optic modulators [21, 25, 26] and PZT-based piezooptomechanical actuators [27–29] with low-confinement silicon nitride waveguides has been demonstrated, but both approaches exhibit significant limitations.

Piezooptomechanical actuator platforms based on aluminum nitride (AlN) implemented using CMOS foundry processes offer a promising alternative with high modulation bandwidths exceeding 100 MHz, ultralow power consumption with negligible hysteresis, and compatibility with cryogenic operation. p. 1
Where the paper says it

In contrast, piezooptomechanical actuator platforms based on aluminum nitride (AlN) implemented using CMOS foundry processes offer a promising alternative [1–3, 5, 30]. Although so far only demonstrated with high-confinement waveguides, these AlN actuators provide high modulation bandwidths (exceeding 100 MHz), ultralow power consumption with negligible hysteresis, and compatibility with cryogenic operation.

Modulator Performance Metrics

The platform achieves a voltage–loss product (VLP) of ∼ 2.8 V·m at 780 nm. p. 0

Where the paper says it

Here we combine piezooptomechanical actuation with a CMOS-foundry-fabricated, low-confinement silicon nitride platform, achieving 2. 6 dB/m propagation loss at 780 nm, megahertz-scale modulation bandwidth, a half-wave voltage-length product of 2.

The modulation bandwidth is in the MHz range, with a time constant τ ≈ 23 ns derived from the frequency response and fall time measurements. p. 5
Where the paper says it

The transmission coefficient S21 rolls off by 3 dB at approximately f3dB = 7 MHz, defining the modulation bandwidth of the piezo-optomechanical actuators and by 6 dB at approximately 9 MHz, while the reflection coefficient S11 remains essentially flat, with no resonant features over the 0–100 MHz range. We confirmed this bandwidth in the time domain by driving the device with a 1 MHz square-wave voltage signal and recording the optical response (Fig.

The circuit demonstrates reconfigurable Mach–Zehnder interferometers with 0. p. 0
Where the paper says it

8 V·m, and negligible hysteresis. We demonstrate reconfigurable Mach–Zehnder interferometers with 0.

63 dB loss per spiral phase shifter, enabling deep, actively reconfigurable visible-wavelength quantum photonic circuits. p. 0
Where the paper says it

We demonstrate reconfigurable Mach–Zehnder interferometers with 0. 63 dB loss per spiral phase shifter, enabling deep, actively reconfigurable visible-wavelength quantum photonic circuits.

Loss Characterization

Propagation loss measurements using top-down imaging yield a propagation loss of 7.2 dB/m for the actuator-integrated waveguide and 2. p. 6

Where the paper says it

In the unetched device, the dominant loss mechanism is scattering at the core–cladding interface due to fabrication imperfections. By contrast, the etched waveguide with an integrated actuator exhibits additional losses from actuator absorption as well as scattering at both the core–cladding and cladding–air interfaces.

57 dB/m for the unetched waveguide. p. 6
Where the paper says it

We characterized the propagation loss using a top-down imaging technique (Ref. 3a) in two distinct low-confinement waveguide geometries: (i) an unetched waveguide without an actuator (Fig.

Optical frequency-domain reflectometry (OFDR) yields a propagation loss of approximately 8–8. p. 6
Where the paper says it

We further verify the propagation loss values using optical frequency-domain reflectometry (OFDR), which sweeps a tunable laser from 773. 2 to 781 nm, yielding a spatial resolution of approximately 27 µm.

3 dB/m for the actuator-integrated waveguide, confirming that the actuator contributes approximately 4–6 dB/m of excess loss beyond the bare waveguide. p. 7
Where the paper says it

When the smaller-bend-radius sections close to the spiral center, where bending loss is high, are included in the fit, the extracted loss increases to approximately 6. 2 cm-long actuator-integrated waveguide, OFDR yields a loss of ∼8–8.

Optimization and Trade-offs

The voltage–loss product (VLP) is used as a figure of merit to capture both effects in a single metric. The authors demonstrate that low α can outweigh the penalty of a larger VπL. p. 9

Where the paper says it

platforms across this trade-off. Our 50 nm-core, low-confinement waveguides, fabricated via PECVD, demonstrate that low α can outweigh the penalty of a larger VπL.

By leveraging strain-induced optical path length modulation through selective release of SPS sections, the VLP could be reduced by a factor of 5–10× relative to current devices, potentially lowering it to ∼ 4 V·dB or below. p. 9
Where the paper says it

Simulations shown in Supplementary Figs. 1a,b indicate that fully releasing selected SPS sections could reduce the VLP by a factor of 5–10× relative to the current devices, potentially lowering it to ∼ 4 V·dB or below.

Quantum State Generation

The success probability for heralding Bell and GHZ states in a lossy LPNP circuit increases by roughly two orders of magnitude with the lower phase-shifter loss, showing dramatic improvements in quantum-state generation efficiency. This low-loss, scalable architecture forms the essential hardware backbone for applications such as quantum routers and on-chip quantum memories. p. 1

Where the paper says it

Introduction Recent work in high-confinement, piezo-optomechanical photonic integrated circuits (PICs) in the visible wavelength regime has demonstrated high circuit densities, fast modulation rates, and low power dissipation/consumption [1–6]. These capabilities make piezo-optomechanical PICs well suited for realizing linear programmable nanophotonic processors (LPNPs) [7], which are scalable, reconfigurable photonic circuits that implement arbitrary linear optical transformations, enabling applications such as quantum resource state generation and linear optical quantum computing.

Scattering Loss Analysis

The dominant source of excess loss is scattering at the cladding–metal interface, where a modal field interacts with surface roughness introduced by metal protrusions in the actuator stack. The calculated scattering loss from this interface is of the order of 10−22 dB/m, which is negligible across all roughness parameters considered. p. 5

Where the paper says it

Advances in fabrication have substantially reduced material absorption losses [49], making geometry-dependent losses the primary contributors to total attenuation. These losses include (i) actuator absorption, (ii) scattering from interfacial roughness, (iii) radiation from waveguide bends, (iv) mode coupling loss at the fiber-to-waveguide interface, and (v) crosstalk 6

Optimal Geometry Determination

The optimal waveguide geometry for minimum VLP with silicon nitride piezo-optic coefficients p11 = −0.125 and p12 = 0. p. 5

Where the paper says it

Because p44 = p11−p12 2 , there are four candidate combinations of p11 and p12, and only p11 = −0. 125 and p12 = 0.

p. 5
Where the paper says it

Because p44 = p11−p12 2 , there are four candidate combinations of p11 and p12, and only p11 = −0. 125 and p12 = 0.

047 is determined by minimizing the product of VLP and αabs/L. p. 6
Where the paper says it

We combine FEM simulations with analytical loss models to estimate the propagation loss in our low-confinement platform, as described in Supplementary Note 7 and illustrated in Supplementary Fig. Using the estimated photoelastic constants, we identify an optimal waveguide geometry by minimizing the voltage–loss product, as discussed in Supplementary Note 6 and Note 8 and in Supplementary Fig.

The optimization process converges to a final VπL of 2. p. 3
Where the paper says it

These MZIs utilize Archimedean-spiral-shaped waveguide phase shifters to reduce both the device footprint and optical bending losses. A scanning electron micrograph of a spiral phase-shifter (SPS) section fabricated using an anneal-free plasma-enhanced chemical vapor deposition (PECVD) process [1, 2, 5, 32, 46] is shown in Fig.

3 V·m with a core width of 1 µm. p. 2
Where the paper says it

a DC SPS SPS DC b G S G MZI SPS Input ports Output ports Electrical contacts Electrical routing Eight-mode linear programmable nanophotonic processor 104 106 108 10-9 10-7 10-5 10-3 Power consumption (W) Modulation speed (Hz) PZT AlN Heater This work Si3 N4 (Anneal-free PECVD) Si3 N4 (LPCVD) Voltage loss product (V-dB) 10 20 30 40 50 10 20 30 40 50 60 Propagation loss (dB/m) This work d SiO2 Si3 N4 Al AlN Undercut Si Actuator Cladding Core Optical mode f c Diced chip 300 µm Diced chip Waveguide e 12. 5 µm ~3 µm 50 nm 300 µm Top view of SPS 1 mm 22.

The resulting core width is 1 µm, with cladding thickness and width of 11. p. 1
Where the paper says it

Without careful design, the increased oxide thickness leads to high mechanical rigidity and, consequently, reduced piezo-optomechanical responsivity. In this work, we show that thick silicon dioxide claddings with an extended undercut beneath the actuator can enable geometries and aspect ratios that concentrate the distribution of stress and optical field within the core and cladding of the waveguide in a way that allows high piezo-optomechanical responsivity even with thick claddings.

6 µm and 12. p. 2
Where the paper says it

a DC SPS SPS DC b G S G MZI SPS Input ports Output ports Electrical contacts Electrical routing Eight-mode linear programmable nanophotonic processor 104 106 108 10-9 10-7 10-5 10-3 Power consumption (W) Modulation speed (Hz) PZT AlN Heater This work Si3 N4 (Anneal-free PECVD) Si3 N4 (LPCVD) Voltage loss product (V-dB) 10 20 30 40 50 10 20 30 40 50 60 Propagation loss (dB/m) This work d SiO2 Si3 N4 Al AlN Undercut Si Actuator Cladding Core Optical mode f c Diced chip 300 µm Diced chip Waveguide e 12. 5 µm ~3 µm 50 nm 300 µm Top view of SPS 1 mm 22.

2 µm, respectively. p. 4
Where the paper says it

(a, b) Cross-sectional SEM images of the fabricated phase modulators. In (b), blue and orange false colors highlight the electrode and the AlN actuator layer, respectively, which is suspended by an undercut.

Material Properties Inference

The best agreement for the simulated VπL value of 2.8 V·m is achieved when using the combination p11 = −0. p. 5

Where the paper says it

8 V · m, together with reported literature values of |p12| and |p44| [30], we roughly infer plausible values for the silicon nitride photoelastic coefficients to guide our future device designs. Because p44 = p11−p12 2 , there are four candidate combinations of p11 and p12, and only p11 = −0.

125 and p12 = 0.047 for silicon nitride. p. 5
Where the paper says it

047 yield simulated values of VπL consistent with the experimental measurement of 2. These findings indicate that silicon dioxide dominates the strain-induced effective refractive index change, whereas silicon nitride contributes an opposing effect, as discussed in Supplementary Note 3.

These findings indicate that silicon dioxide dominates the strain-induced effective refractive index change, whereas silicon nitride contributes an opposing, smaller effect. p. 5
Where the paper says it

047 yield simulated values of VπL consistent with the experimental measurement of 2. These findings indicate that silicon dioxide dominates the strain-induced effective refractive index change, whereas silicon nitride contributes an opposing effect, as discussed in Supplementary Note 3.

The responsivity of high-confinement waveguides is dominated by the photoelastic contribution of the Si3N4. p. 2
Where the paper says it

low-confinement waveguides resides in the silicon dioxide cladding, the comparatively stronger photoelastic response of silicon dioxide [30, 33], despite its lower refractive index than silicon nitride, compensates for the reduced mechanical compliance (see Supplementary Fig. Experimentally, we demonstrate a design achieving piezooptomechanical responsivity comparable to high-confinement systems while lowering optical loss by an order of magnitude [1].

Performance Comparison Table

Table 1 presents a comprehensive summary of the propagation loss and voltage–loss product (VLP) for silicon nitride (Si3N4) waveguide platforms, grouped by optical confinement. The bold row indicates this work. p. 1

Where the paper says it

Introduction Recent work in high-confinement, piezo-optomechanical photonic integrated circuits (PICs) in the visible wavelength regime has demonstrated high circuit densities, fast modulation rates, and low power dissipation/consumption [1–6]. These capabilities make piezo-optomechanical PICs well suited for realizing linear programmable nanophotonic processors (LPNPs) [7], which are scalable, reconfigurable photonic circuits that implement arbitrary linear optical transformations, enabling applications such as quantum resource state generation and linear optical quantum computing.

Active Platform Comparison

Table 2 compares active visible-wavelength modulator and phaseshifter platforms, grouped by the physical tuning mechanism. The efficiency metric is mechanism-dependent: for the electro-optic and piezooptomechanical platforms it is the voltage–length product VπL, whereas the thermooptic, MEMS, and liquid-crystal platforms are characterized by the π-shift power Pπ. p. 2

Where the paper says it

Experimentally, we demonstrate a design achieving piezooptomechanical responsivity comparable to high-confinement systems while lowering optical loss by an order of magnitude [1]. While our focus is on low-confinement visible-wavelength platforms, active modulation has been extensively demonstrated in high-confinement systems, including electro-optic modulators based on thin-film lithium niobate [34–37], lithium tantalate [38], and aluminum nitride [39, 40], as well as electrostatic MEMS phase shifters [41] and thermo-optic tuners [42–45].

Design Constraints

The footprint of the Archimedean spiral is governed by two geometric parameters: the minimum bend radius and the inter-waveguide pitch. Reducing the bend radius shrinks the innermost fold of the spiral and thus the overall device area, but increases bending loss. p. 7

Where the paper says it

57 dB/m obtained from topdown imaging. When the smaller-bend-radius sections close to the spiral center, where bending loss is high, are included in the fit, the extracted loss increases to approximately 6.

Similarly, reducing the waveguide pitch allows more turns within the same area but increases inter-waveguide crosstalk. p. 8
Where the paper says it

3 dB/m, in consistent agreement across top-down imaging, OFDR, and OTDR, as discussed in Supplementary Note 5. Discussion Core thickness governs a fundamental trade-off in piezo-optomechanical phase shifters: a thicker core reduces the mode area and allows a smaller core–actuator separation, improving actuator responsivity (lower VπL), but simultaneously increases scattering loss at the core–cladding interface due to the tighter mode confinement, raising the propagation loss α.

The current pitch of ∼22. p. 8
Where the paper says it

10-15 10-12 10-9 10-6 PBell P4-GHZ x 102 x 108 Success probability Loss per phase shifter (dB) 10-3 1 0 0. 4 G S G G S G Current design Revised version SiO2 Si3 N4 Al AlN Si Core Core Current design Revised version Partially released Fully released a b Fig.

5 µm provides a conservative margin well above this threshold. p. 1
Where the paper says it

Introduction Recent work in high-confinement, piezo-optomechanical photonic integrated circuits (PICs) in the visible wavelength regime has demonstrated high circuit densities, fast modulation rates, and low power dissipation/consumption [1–6]. These capabilities make piezo-optomechanical PICs well suited for realizing linear programmable nanophotonic processors (LPNPs) [7], which are scalable, reconfigurable photonic circuits that implement arbitrary linear optical transformations, enabling applications such as quantum resource state generation and linear optical quantum computing.

Experimental Setup Details

The experiment employs a Keysight 33500B function generator in combination with a Thorlabs BPA100 benchtop high-voltage piezo amplifier to drive the SPS. S-parameter measurements are performed using a Keysight P9374A vector network analyzer. p. 5

Where the paper says it

Although operating at or above resonance can enhance the optomechanical response, it also induces narrowband behavior, ringing, and phase lag, so the fundamental eigenfrequency ultimately sets the upper limit of the usable bandwidth. We characterized the modulator’s frequency response using a vector network analyzer (VNA), as shown in Fig.

Top-down imaging is conducted using an Allied Vision 1800 U-120c camera equipped with a Navitar 12× UltraZoom Video Microscopy System and a Mitutoyo 5× microscope objective. p. 7
Where the paper says it

(a) Schematic of the experimental setup for measuring waveguide loss using a top-down micrograph technique. The setup includes a 780 nm laser, polarization controller (PC), and a camera equipped with a 12× zoom lens and a 5× microscope objective (MO).

Optical time-domain reflectometry (OTDR) is employed using a femtosecond laser, a time-tagger with an avalanche photodiode (APD), and a fast photodetector. p. 8
Where the paper says it

3d and Supplementary Note 5. We additionally cross-validate the actuator-free result using optical timedomain reflectometry (OTDR) with a femtosecond source, which has a coarser spatial resolution of 2.

Scattering Loss Model

The two-dimensional scattering loss formalism used here is a normalized variant of the Payne–Lacey model. The total scattering loss for mode n is obtained by multiplying the normalized sidewall coefficient by the modal overlap (ϕn). p. 6

Where the paper says it

Among these, absorption and scattering losses are particularly sensitive to waveguide dimensions (see Supplementary Note 6 and Supplementary Fig. 9), as variations in core and cladding size can significantly alter modal overlap with absorptive or rough regions.

The total propagation loss is expressed as α = α(n)total +αabs, where αabs is the material absorption loss. p. 5
Where the paper says it

Loss characterization of low-confinement waveguide The overall attenuation (α) of optical modes in low-confinement waveguides arises from both intrinsic material properties and device geometry. Advances in fabrication have substantially reduced material absorption losses [49], making geometry-dependent losses the primary contributors to total attenuation.

Excess Loss Mechanisms

The excess loss arises from three distinct mechanisms: (i) Absorption loss from the metal electrodes, (ii) Scattering loss from the cladding–metal interface, and (iii) Scattering loss from the cladding–air interface. The buried oxide height that minimizes the overall VLP = Vπ · L × αabs explicitly accounting for both contributions corresponds to a metal–core separation of ∼2. p. 6

Where the paper says it

We therefore attribute the excess loss primarily to scattering at the cladding–metal interface, caused by nanoscale metal protrusions that extend into the oxide cladding. Smaller contributions arise from metal absorption and scattering at the cladding–air interface, as analyzed in detail in Supplementary Note 9.

5 µm.

Heralding Protocol

The protocol for heralding Bell states in the first and second modes is achieved by performing temporal mode-resolving photon-number-resolving detection (PNRD). The probability of success of the protocol in the presence of losses is shown in Supplementary Figure 5e. p. 8

Where the paper says it

The arrows highlight the significant improvement in success probability achieved by reducing the loss per phase shifter from 1 dB to 0. 2 dB; this reduction yields probability enhancement factors of ∼ 102 for Bell states and ∼ 108 for 4-mode GHZ states (see Supplementary Note 4 for details).

The ideal case without losses yields a probability of success of 0. p. 8
Where the paper says it

The arrows highlight the significant improvement in success probability achieved by reducing the loss per phase shifter from 1 dB to 0. 2 dB; this reduction yields probability enhancement factors of ∼ 102 for Bell states and ∼ 108 for 4-mode GHZ states (see Supplementary Note 4 for details).

125.

Future Applications

This low-loss, scalable architecture forms the essential hardware backbone for applications such as quantum routers and universal quantum photonic logic circuits. The platform’s ultra-low propagation loss and anneal-free, foundry-compatible fabrication process enable seamless integration of single-photon sources, modulators, and electronic control. p. 0

Where the paper says it

edu; Abstract Realizing photonic quantum computing at scale requires integrated circuits that combine ultra-low loss with fast, low-power, low-hysteresis, and low-crosstalk reconfiguration. These requirements are particularly challenging at visible wavelengths, where many quantum resource-state generators, including single-photon sources and quantum memories, naturally operate.

This paves the way for complex, scalable, and fully integrated quantum photonic systems on a single chip. p. 1
Where the paper says it

Introduction Recent work in high-confinement, piezo-optomechanical photonic integrated circuits (PICs) in the visible wavelength regime has demonstrated high circuit densities, fast modulation rates, and low power dissipation/consumption [1–6]. These capabilities make piezo-optomechanical PICs well suited for realizing linear programmable nanophotonic processors (LPNPs) [7], which are scalable, reconfigurable photonic circuits that implement arbitrary linear optical transformations, enabling applications such as quantum resource state generation and linear optical quantum computing.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

1

Improve circuit design by optimizing waveguide geometry using a combined figure of merit such as VpiL to minimize both voltage loss product and scattering loss. This allows for an optimal core height (h) of around 2.5 µm to minimize the contributions of both VpiL and alphaabs.

2

Enhance quantum state generation efficiency by designing phase shifters with a voltage length product (VpiL) below 4 V·dB, which would result in a loss per phase shifter less than 0.2 dB at Vmax = 20 V. This reduction leads to probability enhancement factors of 108 for heralded four-mode GHZ states compared to high-confinement platforms.

3

Develop a platform capable of realizing deep, actively reconfigurable visible-wavelength quantum photonic circuits by leveraging the combination of piezooptomechanical actuation with CMOS foundry fabricated, low confinement silicon nitride waveguides. This system can achieve a propagation loss of 2.6 dB/m at 780 nm and a modulation bandwidth in the megahertz scale.

Abstract

Realizing photonic quantum computing at scale requires integrated circuits that combine ultra-low loss with fast, low-power, low-hysteresis, and low-crosstalk reconfiguration. These requirements are particularly challenging at visible wavelengths, where many quantum resource-state generators, including single-photon sources and quantum memories, naturally operate. Low-confinement silicon nitride waveguides offer the requisite loss performance, but conventional thermo-optic modulators dissipate significant static power, driving thermal crosstalk and precluding cryogenic operation. Visible-wavelength piezo-optomechanical circuits avoid these drawbacks, but existing demonstrations rely either on high-confinement waveguides with propagation losses of 35-100 dB/m, or on low-confinement platforms using foundry-incompatible PZT. Here we combine piezo-optomechanical actuation with a CMOS-foundry-fabricated, low-confinement silicon nitride platform, achieving 2.6 dB/m propagation loss at 780 nm, megahertz-scale modulation bandwidth, a half-wave voltage-length product of 2.8 Vm, and negligible hysteresis. We demonstrate reconfigurable Mach-Zehnder interferometers with 0.63 dB loss per spiral phase shifter, enabling deep, actively reconfigurable visible-wavelength quantum photonic circuits.

Sources

Related papers