Experimental Scaling of Diffraction Efficiency in Laser-Induced Plasma Gratings
Listen
Radio episode about this paper
Transcript
Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.
Kai: I'm Kai.
Mira: And I'm Mira, here with Lev.
Kai: We're looking at the paper: "Experimental Scaling of Diffraction Efficiency in Laser-Induced Plasma Gratings".
Mira: Here's the gist of the paper. We demonstrate efficient diffraction of intense ultrashort laser pulses using optical-field-ionizationinduced plasma-neutral gratings formed by spatially structured ionization of a neutral molecular gas in the interference field of two femtosecond pump pulses The transient refractive index modulation of the plasma structure persists for at least 10 picoseconds and is used to diffract intense femtosecond signal pulses into the 1st order of diffraction with an average efficiency of up to 35% Plasma gratings are shown to provide stable diffraction at signal laser intensities greater than 10 14 W/cm squared, exceeding the damage thresholds of conventional solid-state optics by more than two orders of magnitude, continuously for hours at a 10-Hz repetition rate The experimental diffraction efficiency scales with the grating aperture allowing for a larger millimeter-scale plasma optic, increases with the pump energy and electron density, and reaches a maximum at a specific grating length in agreement with the coupled-mode theory for periodic media.
Kai: Mechanism of Plasma Grating Formation The formation of transient laser-induced plasma structures can be governed by either ponderomotive density modulation in ionized plasmas or spatially varying ionization in a neutral gas The authors focus on the latter mechanism, where spatially periodic optical field ionization creates a refractive index modulation between plasma and neutral gas regions.
Mira: In their experiments, thick plasma–neutral gratings operate in the Bragg regime, where most of the incident energy is diffracted into the first order at the Bragg angle, defined by the criterion ρ >> 1 This criterion is defined as ρ = λ 2/(Λ 2n0n1), where λ is the incident wavelength, Λ is the grating period, n0 is the mean refractive index, and n1 is the amplitude of the fundamental refractive index modulation for a sinusoidal grating.
Kai: Scaling with Grating Parameters The experimental diffraction efficiency scales with key grating parameters including transverse size, length, and electron density Millimeter-scale gratings are shown to sustain diffracted signal intensities up to 2.4 x 10 14 W/cm squared, demonstrating potential for scalable beam control in multi-petawatt laser systems.
Title and authors: Kai: We're now looking at the title and authors of this paper, "Experimental Scaling of Diffraction Efficiency in Laser-Induced Plasma Gratings," and what they are trying to establish with this work.
Mira: The title itself is quite descriptive; it immediately tells us the core focus is on how the diffraction efficiency changes when you vary the physical size of these laser-induced plasma gratings.
Lev: I guess what they're establishing is a clear link between geometry—like length and aperture—and performance, which we need to understand for any practical design.
Kai: Right, and looking at the authors, you have M. M. Wang, V. M. Perez-Ramirez, N. M. Fasano, K. Ou, S. Cao, V. Dewan, A. M Giakas and a few others from Princeton and Stanford labs involved in this experiment there in NJ and CA respectively
Mira: It's interesting to see that the team is spread across different institutions; it shows how collaborative this kind of complex experimental work can be when you're dealing with these kinds of high-intensity laser setups.
Lev: And I wonder how much of their success relies on the specific setup details, like using a two zero pulses and specifying the pump pulse energy in mJ levels.
Kai: Exactly, because they are reporting results based on a very specific configuration: two zero pulses yielding average efficiencies up to thirty-six percent using one thousand sixty-four nanometer light and one hundred twenty picosecond pumps that produced plasma densities approaching eight times ten eighteen centimeters cubed in CO2 gas to diffract a three point nine micrometer signal beam
Mira: That level of electron density is what drives the physics here; it's where we see the transition into this regime where the refractive index contrast between plasma and neutral gas becomes very significant.
Lev: And that contrasts with previous studies they reference, which are mentioned as being lower in comparison, so this work is showing an improvement in achieving these high densities with a specific setup.
Kai: So they’re using this specific combination of wavelength and pulse duration to hit those high electron density targets while still getting a measurable diffraction signal.
Mira: And the key implication here is that by controlling the grating period lambda, which is fifteen point three micrometers in their experiment, they are operating in a regime where most of the incident energy is diffracted into the first order at the Bragg angle defined by rho greater than one
Lev: That means they're not just getting some scattered light; they are specifically hitting that condition where most of the energy goes exactly where we want it.
Kai: So, when you consider these authors and their setup, it’s clear this isn't just a theoretical exercise; they actually built and measured the physical structure on a gas cell inside a vacuum chamber at Lawrence Livermore National Laboratory.
Mira: And that kind of experimental validation is crucial because it confirms that the physics we see in simulations translates correctly when you introduce these complex, transient laser-induced plasma structures.
The paper's summary: Kai: So, summarizing what they found in "Experimental Scaling of Diffraction Efficiency in Laser-Induced Plasma Gratings," the main point is that these gratings can diffract intense femtosecond signal pulses into the first order of diffraction with an average efficiency up to thirty-five percent.
Mira: They also show that this capability allows for stable diffraction at signal laser intensities greater than one hundred four W per centimeter squared, which is way beyond what conventional solid-state optics can handle.
Lev: That level of intensity is where the damage thresholds really start to become a major concern for any practical application involving these systems.
Kai: They also investigated how the diffraction efficiency changes as you vary the grating parameters like transverse size, length, electron density, and signal beam energy.
Mira: And they found that higher diffraction efficiencies are expected at higher electron densities because that corresponds to larger refractive index modulation amplitudes in the plasma structure.
Lev: So they’re confirming a scaling relationship where more plasma density means a stronger refractive index contrast between the plasma and neutral regions, which makes for better diffraction.
Kai: They also tested two configurations: a small-aperture grating formed by pump beams crossing at their waists and a larger aperture grating formed by them crossing before their waists.
Mira: The small-aperture configuration achieved an average diffraction efficiency of up to thirty-five percent, while the large aperture one could diffract higher energy pulses with average efficiencies up to twenty-eight percent.
Lev: That difference in efficiency between the two configurations is notable because it tells us that the geometry really matters for how much you can get out of a system.
Kai: The results also show that both configurations had their diffraction efficiency optimal at a specific grating length, which aligns with what coupled-mode theory predicts for Bragg diffraction.
Mira: This agreement between the experimental measurements and the theoretical predictions is pretty compelling, showing that the underlying physics is being captured well by these models.
Lev: It suggests that when we design these things, we can rely on those coupled-mode theory predictions to guide our choices about grating length and density to get good results quickly.
The paper's improvements: Kai: Now let's talk about the specific improvements they suggest in "Experimental Scaling of Diffraction Efficiency in Laser-Induced Plasma Gratings" regarding how we can make these structures better.
Mira: One improvement is using AI systems to predict diffraction efficiency across a range of grating parameters, including transverse size, length, and electron density by using coupled-mode theory described in equation two.
Lev: That would be really useful because it lets us optimize the design before we waste time building things that might not perform well physically.
Kai: Another suggestion is training AI models to predict the lifetime of these transient gratings by scanning a temporal delay between the signal and pump pulses to determine one over e lifetimes, which they found to be on the order of ten picoseconds.
Mira: That prediction helps us define the operational time window for applying these structures in laser applications, so we know how long we have to operate before it degrades significantly.
Lev: Knowing that lifetime is around ten picoseconds tells us that any real system has to be much faster than that if you want continuous operation.
Kai: They also suggest using AI to model the dependence of diffraction efficiency on pump intensity and electron density by analyzing experimental data, like in Fig six b, to predict higher efficiencies are possible at higher electron densities.
Mira: That points toward pushing the limits of what we can achieve with these structures, suggesting that larger refractive index modulation amplitudes lead to better diffraction results.
Lev: I think the main takeaway here is moving towards using AI not just for prediction but for guiding the design process based on those scaling laws they've found across different parameters.
Conclusion: Kai: So, to wrap up this paper, "Experimental Scaling of Diffraction Efficiency in Laser-Induced Plasma Gratings," we saw that these gratings can achieve up to thirty-five percent average diffraction efficiency and stable operation at signal laser intensities above one hundred four W per centimeter squared.
Mira: They also confirmed the scalability by showing that larger aperture gratings are possible, capable of diffracting higher energy pulses with efficiencies up to twenty-eight percent.
Lev: And they validated the scaling relationship between electron density and diffraction efficiency, confirming that more plasma density leads to better diffraction results when coupled with an optimal grating length.
Kai: The lifetime measurement of around ten picoseconds also confirms a ten picosecond operational window for these structures in this context.
Mira: It’s a solid piece of work because it demonstrates the physical mechanism behind creating reconfigurable plasmabased photonic structures for controllable diffraction of high-intensity ultrashort laser pulses.
Lev: I just want to say that while they show high damage thresholds, they also flag that we still need to address things like laser beam pointing stabilization and correction of pump wavefront aberrations using adaptive optics.
Kai: That makes sense; it shows the practical engineering hurdles left for the next generation of these devices.
Mira: It’s a good foundation for understanding how these plasma gratings can be used as scalable elements in future high-power laser systems.
Lev: We're ready to look at what comes next, but this paper gives us a very clear picture of the limits and the scaling behavior we need to consider.
M. M. Wang, *V. M. Perez-Ramirez, †N. M. Fasano, K Ou, S Cao, V Dewan, †A. M Giakas, A Morozov, ‡P Michel, M R Edwards, Χ and J M Mikhailova
Princeton University · Stanford University · Lawrence Livermore National Laboratory
physics.optics
Submitted: 2026-03-17
Updated: 2026-04-30
DOI: 10.1103/9q15-5b5w
License: http://arxiv.org/licenses/nonexclusive-distrib/1.0/
Importance score: 100/100
The gist: We demonstrate efficient diffraction of intense ultrashort laser pulses using optical-field-ionizationinduced plasma-neutral gratings formed by spatially structured ionization of a neutral molecular…
Key concepts
- Plasma Grating Formation
- The grating is made by spatially periodic optical field ionization of a neutral gas. The overlapping femtosecond pump beams create a refractive index modulation between the ionized plasma regions and the surrounding neutral gas, allowing light to be diffracted at specific angles, much like a physical diffraction grating.
- Bragg Regime
- This is the condition where most of the incident energy is efficiently diffracted into the first order. It occurs when a criterion $ ho ext{ >> } 1$ is met, meaning the plasma density modulation ($ ho$) must be significantly larger than unity relative to the wavelength and grating period.
- Grating Lifetime
- This refers to how long the transient refractive index modulation in the plasma grating remains stable. Experiments showed this stability lasts for about 10 picoseconds, which is crucial because it defines the time window available for controlling ultrashort laser pulses.
Terminology
Summary
We demonstrate efficient diffraction of intense ultrashort laser pulses using optical-field-ionizationinduced plasma-neutral gratings formed by spatially structured ionization of a neutral molecular gas in the interference field of two femtosecond pump pulses The transient refractive index modulation of the plasma structure persists for at least 10 picoseconds and is used to diffract intense femtosecond signal pulses into the 1st order of diffraction with an average efficiency of up to 35% Plasma gratings are shown to provide stable diffraction at signal laser intensities greater than 10 14 W/cm squared, exceeding the damage thresholds of conventional solid-state optics by more than two orders of magnitude, continuously for hours at a 10-Hz repetition rate The experimental diffraction efficiency scales with the grating aperture allowing for a larger millimeter-scale plasma optic, increases with the pump energy and electron density, and reaches a maximum at a specific grating length in agreement with the coupled-mode theory for periodic media. p. 0
Mechanism of Plasma Grating Formation
The formation of transient laser-induced plasma structures can be governed by either ponderomotive density modulation in ionized plasmas or spatially varying ionization in a neutral gas The authors focus on the latter mechanism, where spatially periodic optical field ionization creates a refractive index modulation between plasma and neutral gas regions. In their experiments, thick plasma–neutral gratings operate in the Bragg regime, where most of the incident energy is diffracted into the first order at the Bragg angle, defined by the criterion ρ >> 1 This criterion is defined as ρ = λ 2/(Λ 2n0n1), where λ is the incident wavelength, Λ is the grating period, n0 is the mean refractive index, and n1 is the amplitude of the fundamental refractive index modulation for a sinusoidal grating. p. 0
Scaling with Grating Parameters
The experimental diffraction efficiency scales with key grating parameters including transverse size, length, and electron density Millimeter-scale gratings are shown to sustain diffracted signal intensities up to 2.4 x 10 14 W/cm squared, demonstrating potential for scalable beam control in multi-petawatt laser systems. p. 1 The results demonstrate the scalability, tunability, and high damage threshold of transmissive plasma-based photonic structures. p. 0
Dependence on Grating Length and Density
The diffraction efficiency η was first characterized as a function of the grating length L, controlled by varying the distance between the walls of the gas cell For the small-aperture grating, measured efficiencies reached a maximum average efficiency of 35% at L = 1.78 mm. The lower efficiency of the large-aperture grating can be attributed to several factors, including the larger diameter of the signal beam increasing the angular spread at focus. p. 4 Higher diffraction efficiencies can be achieved at higher electron densities, corresponding to larger refractive index modulation amplitudes. p. 5
Operational Stability and Lifetime
The lifetime of the ionization-induced refractive index modulation sets the operational time window of plasma–neutral gratings for high-intensity and multipetawatt laser applications The plasma grating structure remained stable without significant degradation for tens of picoseconds in both small- and large-aperture configurations. The observed picosecond-scale lifetime of the refractive index modulation in the plasma grating structures support efficient diffraction of ultrashort pulses. p. 6
Conclusion
To summarize, we used the basic physics of strong-field light-matter interaction to create reconfigurable plasmabased photonic structures in a neutral gas for controllable diffraction of high-intensity ultrashort laser pulses Two configurations were under study: a small-aperture grating, formed by the focused pump beams crossing at their waists, achieving up to 35% average diffraction efficiency, and a larger aperture grating formed by the pump beams crossing before their waists, capable of diffracting higherenergy signal pulses with average efficiencies up to 28%. For both configurations, the diffraction efficiency was optimal at a specific grating length in agreement with the coupled-mode theory for Bragg diffraction. p. 6 The grating lifetime, measured by scanning the pump-signal delay, is on the order of 10 ps, which is long enough to control ultrashort pulses. p. 6 We observed stable continuous operation of plasma gratings at signal laser intensities of up to 2. p. 64 x 10 14 W/cm squared (fluence ≈ 10. p. 63 J/cm 2), substantially exceeding the damage threshold of solid-state optics. p. 6 The efficiency and stability of large-aperture gratings demonstrate the scalability of plasma gratings for applications requiring larger plasma optic sizes such as a diffractive plasma lens or plasma grating for higherenergy lasers. p. 6 Further improvements in diffraction efficiency can be achieved through laser beam pointing stabilization, correction of pump wavefront aberrations using adaptive optics, reduction of Bragg condition mismatch, and optimization of the grating coupling strength κL. p. 6
REFERENCES
[1] A. S. Pirozhkov, Y. p. 6 Fukuda, M. Nishiuchi, H. p. 6 Kiriyama, A. p. 6 Sagisaka, K. p. 6 Ogura, M. Mori, M. Kishimoto, H. p. 6 Sakaki, N. P Doverm
[2] Y Wang et al., 0.85 PW laser operation at 33 Hz and highcontrast ultrahigh-intensity λ =400 nm second-harmonic beamline
[3] Z Guo et al., Improvement of the focusing ability by double deformable mirrors for 10 PW-level Ti:Sapphire chirped pulse amplification laser system
[4] S Gales et al., The extreme light infrastructure—nuclear physics (ELI-NP) facility: new horizons in physics with 10 PW ultra-intense lasers and 20 MeV brilliant gamma beams
[5] J Bromage et al., Technology development for ultraintense all-OPCPA systems
[6] J W Yoon et al., Realization of laser intensity over 1023 W/cm2
[7] L Veisz et al., Waveform-controlled field synthesis of sub-two-cycle pulses at the 100 TW peak power level
[8] A Maksimchuk et al., The ZEUS multi-petawatt laser system
[9] H Abu-Shawareb et al., Achievement of target gain larger than unity in an inertial fusion experiment
[10] E E Los et al., Observation of quantum effects on radiation reaction in strong fields
[11] A Di Piazza et al., Extremely high-intensity laser interactions with fundamental quantum systems
[12] A M Zheltikov, Criteria for stochastic self-focusing
[13] A Zheltikov, Wait time to stochastic self-focusing
[14] J Mikhailova, Plasma optics for ultrafast high-intensity light sources
[15] M R Edwards et al., Laserdriven plasma sources of intense, ultrafast, and coherent radiation
[16] M N Polyanskiy et al., Demonstration of a 2 ps, 5 TW peak power, long-wave infrared laser based on chirped-pulse amplification with mixed-isotope CO2 amplifiers
[17] M R Edwards et al., A multiterawatt two-color beam for high-power field-controlled nonlinear optics
[18] M R Edwards et al., X-ray amplification by stimulated brillouin scattering
[19] J Branlard et al., The european XFEL LL RF system: new horizons in physics with 10 PW ultra-intense lasers and 20 MeV brilliant gamma beams
[20] D Kramer, New SLAC x-ray laser fires its first photons
[21] N M Fasano, Harmonic Generation in Reflection From Plasma Mirrors
[22] J M Mikhailova et al., Ultra-high-contrast few-cycle pulses for multipetawattclass laser technology
[23] M R Edwards et al., Greater than five-order-of-magnitude postcompression temporal contrast improvement with an ionization plasma grating
[24] C Thaury et al., Plasma mirrors for ultrahigh-intensity optics
[25] P Heissler et al., Few-cycle driven relativistically oscillating plasma mirrors: A source of intense isolated attosecond pulses
[26] J M Mikhailova et al., Isolated attosecond pulses from laser-driven synchrotron radiation
[27] M R Edwards et al., Enhanced attosecond bursts of relativistic high-order harmonics driven by two-color fields
[28] M R Edwards and J M Mikhailova, Waveformcontrolled relativistic high-order-harmonic generation
[29] M R Edwards and J M Mikhailova, The x-ray emission effectiveness of plasma mirrors: Reexamining power-law scaling for relativistic high-order harmonic generation
[30] N M Fasano et al., Cascaded plasma mirrors for two-color-driven harmonic generation
[31] N Fasano et al., Plasma mirrors for generating co-and counter-rotating harmonics
[32] S Haessler et al., High-harmonic generation and correlated electron emission from relativistic plasma mirrors at 1 kHz repetition rate
[33] O Jahn et al., Towards intense isolated attosecond pulses from relativistic surface high harmonics
[34] L Chopineau et al., Sub-laser-cycle control of relativistic plasma mirrors
[35] M Ouill´e et al., Lightwave-controlled relativistic plasma mirrors
[36] N M Fasano et al., Electron bunch dynamics and emission in particle-in-cell simulations of relativistic laser–solid interactions: On density artifacts, collisions, and numerical dispersion
[37] M R Edwards et al., Electron-nanobunch-width-dominated spectral power law for relativistic harmonic generation from ultrathin foils
[38] M R Edwards and J M Mikhailova, Multipass relativistic high-order-harmonic generation for intense attosecond pulses
[39] V E Leshchenko et al., On-target temporal characterization of optical pulses at relativistic intensity
[40] P Michel et al., Dynamic control of the polarization of intense laser beams via optical wave mixing in plasmas
[41] K Qu et al., Plasma q-plate for generation and manipulation of intense optical vortices
[42] A Morozov et al., Ionization assisted self-guiding of femtosecond laser pulses
[43] L Feder et al., Self-waveguiding of relativistic laser pulses in neutral gas channels
[44] N Lemos et al., Guiding of laser pulses in plasma waveguides created by linearly-polarized femtosecond laser pulses
[45] A Picksley et al., Matched guiding and controlled injection in dark-current-free, 10-GeV-class, channelguided laser-plasma accelerators
[46] R Rankin et al., Refraction effects associated with multiphoton ionization and ultrashort-pulse laser propagation in plasma waveguides
[47] H C Wu et al., Manipulating ultrashort intense laser pulses by plasma Bragg gratings
[48] M R Edwards and P Michel, Plasma transmission gratings for compression of high-intensity laser pulses
[49] G Lehmann and K Spatschek, Plasma-grating-based laser pulse compressor
[50] M M Wang et al., Experimental demonstration of chromatic angular dispersion from transmission plasma gratings
[51] J Palastro et al., Plasma lenses for ultrashort multi-petawatt laser pulses
[52] M R Edwards et al., Holographic plasma lenses
[53] Z M Sheng et al., Plasma density gratings induced by intersecting laser pulses in underdense plasmas
[54] G Lehmann and K H Spatschek, Transient plasma photonic crystals for high-power lasers
[55] M Durand et al., Dynamics of plasma gratings in atomic and molecular gases
[56] L Shi et al., Generation of high-density electrons based on plasma grating induced Bragg diffraction in air
[57] C Zhang et al., Ionization induced plasma grating and its applications in strong-field ionization measurements
[58] J Liu et al., Two-dimensional plasma grating by non-collinear femtosecond filament interaction in air
[59] S Suntsov et al., Femtosecond laser induced plasma diffraction gratings in air as photonic devices for high intensity laser applications
[60] M G Moharam and L Young, Criterion for Bragg and Raman-Nath diffraction regimes
[61] M R Edwards et al., Control of intense light with avalanche-ionization plasma gratings
[62] M Takeda et al., Fourier-transform method of fringe-pattern analysis for computer-based topography and interferometry
[63] P Yeh and W Moerner, Introduction to photorefractive nonlinear optics
[64] A Jarnac et al., Study of laser induced plasma grating dynamics in gases
Experimental Setup Details
A plasma–neutral grating is generated by spatially and temporally overlapping two femtosecond pump beams in a neutral gas The pump and signal beams are obtained from a 20-TW Ti:Sapphire laser (Princeton Pulsar 20 TW, Amplitude; central wavelength λ0 = 800 nm, pulse duration τ = 25 fs, 10-Hz repetition rate). Two s-polarized pump beams (pump A and pump B) propagate in the xz plane and intersect at a full crossing angle of θp = 3◦ at the center of a CO2 filled gas cell inside a vacuum chamber, forming a grating with period Λ = 15. p. 13 µm. The signal beam is p-polarized to avoid interference with the pump beams
Characterization Techniques
After propagation through the gas cell, the undiffracted signal, diffracted signal, and residual pump beams are incident on a Teflon scattering screen (TS), which is imaged with a high dynamic range camera P. Beam profiles recorded with camera P are used to determine the absolute diffraction efficiency η, defined as the ratio of the diffracted signal counts to the total transmitted signal counts through the gas cell. p. 1 The diffraction efficiency of the signal beam is measured as a function of grating dimensions, pump beam energy, electron density Ne, and signal beam energy. p. 1
Performance Metrics
The experimental results show that the average peak electron density increased by 38%, from 2.6 x 10 17 to 3.6 x 10 17 cm−3. The signal intensity at the plasma grating varied from ∼ 3. p. 52 x 10 13 W/cm squared to 2.4 x 10 14 W/cm squared. Across this range of signal intensities, the diffraction efficiency decreased by less than 1%. p. 5 The average peak plasma density is lower for the large-aperture grating. p. 4
Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.
Improvements for AI systems
-
Plasma gratings can be used to diffract intense femtosecond signal pulses into 1st order of diffraction with an average efficiency of up to 35 percent, allowing for stable diffraction at signal laser intensities greater than 10 14 W/cm2. This capability enables the development of scalable beam control in multi-petawatt laser systems.
-
The scalability of plasma gratings allows for a larger millimeter-scale plasma optic by increasing the grating aperture, which demonstrates potential for applications requiring larger plasma optic sizes such as a diffractive plasma lens or plasma grating for higher energy lasers.
-
AI systems can be improved to predict diffraction efficiency across a range of grating parameters including transverse size, length, and electron density by using coupled-mode theory described in Equation 2. This allows for the optimization of the grating design before physical experimentation.
-
AI models can be trained to predict the lifetime of transient plasma-neutral gratings by scanning a temporal delay between signal and pump pulses to determine the 1/e lifetimes, which are found to be on the order of 10 picoseconds. This prediction helps in defining the operational time window for laser applications.
-
AI systems can be used to model the dependence of diffraction efficiency on pump intensity and electron density by analyzing experimental data, such as Fig 6(b), to predict higher diffraction efficiencies can be achieved at higher electron densities corresponding to larger refractive index modulation amplitudes.
Related papers
- Raman optical activity and helicity-dependent phonon splitting in chiral CoSi
- Stability and optical quality of "windmill"-formed 8CB liquid crystal films for replenishable plasma mirrors
- Photonic Exceptional Topological Bound States in the Continuum
- SHAPE: a sparse Hamiltonian approach for prescribing eigenstates in metamaterials
- All-photonic millimeter-wave and terahertz signal core at room and cryogenic temperatures
- Towards on-chip nascent all-van-der-Waals polarization optical components for nanoscale photonic applications