Bright and pure single-photon source in a silicon chip by nanoscale positioning of a color center in a microcavity
Listen
Radio episode about this paper
Transcript
Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.
Kai: I'm Kai.
Mira: And I'm Mira, here with Lev.
Kai: We're looking at the paper: "Bright and pure single-photon source in a silicon chip by nanoscale positioning of a color center in a microcavity".
Mira: Here's the gist of the paper. Bright and pure single-photon source in a silicon chip by nanoscale positioning of a color center in a microcavity is presented by fabricating an all-silicon source of near-infrared linearly-polarized single photons through the nanoscale positioning of a color center in a silicon-on-insulator microcavity The results demonstrate that this method represents a major step towards on-demand sources of indistinguishable near-infrared single photons within silicon photonics chips Source Fabrication and Characterization The W centers are created by a well-known combination of Si+ implantation and thermal annealing The implantation is performed through a mask patterned with nanoholes whose size is tuned to locally create single W centers For a nanohole diameter of 150 nm, single W centers are observed with a yield of 40% with low background emission (g 2(0) ≈ 0.1) and average count rate of 3.2 ± 0.8 kcps The CBG cavities are fabricated by electron beam lithography and reactive ion etching at the same location as the nanoholes Cavity Optimization and Coupling Effects The Purcell enhancement factor F, defined as the ratio between the emission rate in the cavity and bulk silicon, is heavily dependent on the position of the emitter A maximum enhancement factor of 13 is obtained at the center of the cavity The collection efficiency for a cavity-coupled W center was also investigated using FDTD, considering the configuration of our measurement setup A collection efficiency of 51% is obtained at the center of the cavity The spectral detuning ∆λ is the difference between the emission wavelength of the dipole and λres = 1218 nm A collection efficiency of 51% is obtained at zero-detuning, and remains above 40% in the
-20 - +10: nm detuning range Emission Properties and Purity The PL intensity at saturation of the W-1 spot is 1.29±0.01 Mcps together A clean antibunching dip is observed without any correction for detectors dark counts or background emission, with g(2)(0) = 0.03 ± 0.01 at P = 2.8Psat These g(2)(0) values are among the best reported values for Si color centers, as shown in Table I The ZPL accounts for ξ = 98.6 ± 1.4% of the PL intensity Performance and Future Directions Under weak pumping condition, the triggered emission of single-photon pulses is demonstrated with 93±2% purity The zero-phonon emission rate is increased by a factor F > 7.2 While point (1) and the issue of blinking have already been discussed, we see that points (2) and (3) can be radically improved by replacing our low-Fp CBG cavity by a high-Fp waveguide-coupled photonic crystal cavity The strategy is compatible with the integration of multiple single-photon sources connected to the same photonic circuit for quantum applications The bright emission of antibunched photons under CW excitation unveils the strong potential of W centers for building a deterministic SPS in SOI In conclusion, we have demonstrated a source of nearinfrared linearly-polarized single photons obtained by nanoscale positioning of a W center in a SOI CBG cavity Si+ implantation through a mask patterned with nanoholes allows for selective creation of single W centers, positioned in the vicinity of the main antinode of the resonant mode The cavity-coupled emitter has a PL intensity at saturation of 1.29±0.01 Mcps together, with a g(2)(0) value inferior to 0.06 under above-gap CW excitation up to P = 9.2Psat, and with a ZPL fraction of 98.6 ± 1.
Paper summary: Kai: So, looking at the title, "Bright and pure single-photon source in a silicon chip by nanoscale positioning of a color center in a microcavity," it really sums up the whole effort here. It’s about achieving brightness and purity in silicon by controlling where you put that W center.
Mira: Exactly. The authors are showing that this specific technique—the nanoscale positioning—is what allows them to get these near-infrared linearly-polarized single photons from silicon, and they achieved a photon count rate of one point twenty-nine plus or minus zero point one megacounts per second at saturation.
Lev: From an engineering standpoint, the implication is that if you can precisely control the emitter's position to get nearunity probability of being within one hundred twenty nanometers of the cavity center, you have a pathway to building deterministic single-photon sources.
Kai: And they also showed that under continuous wave excitation, they got a g squared zero value inferior to zero point six under above-gap continuous wave excitation up to two point eight psat when pumped at nine point two psat.
Mira: That low antibunching measurement is important because it means the source is good enough for single-photon applications, which they've also shown has a zero phonon line fraction of ninety-eight point six plus or minus one point four percent in intensity.
Lev: The limitation they mention is that they are still using this low Purcell factor CBG cavity, and the authors suggest replacing it with a high Purcell factor waveguide-coupled photonic crystal cavity to radically improve points two and three.
Kai: So, the paper proves that this method works for creating these sources, but the next step in making them truly useful for quantum computing is swapping out that current low Purcell factor cavity.
Mira: Right, so it’s a proof of concept with a clear roadmap for improvement towards on-demand sources within silicon photonics chips.
Conclusion: Kai: So, this paper is about making single photons bright and pure in silicon by precisely placing a color center inside a microcavity.
Mira: It’s essentially showing how controlling that exact spot allows you to get high-quality near-infrared photons out of silicon chips on demand.
Lev: From an engineering standpoint, it means we can build these deterministic sources inside the existing silicon photonics infrastructure.
Kai: The authors achieved a saturation power intensity of one point two nine plus or minus zero point zero one megacounts per second, which is pretty good for this setup.
Mira: They also reported a very low antibunching measurement, a g squared zero value of zero point zero three plus or minus zero point one under those above-gap conditions.
Lev: That low number is what we need to actually run error correction on hardware because it means the source is relatively clean when you try to use it.
Kai: The core idea here is using nanoscale positioning to get that emitter exactly where it needs to be for maximum light enhancement in the cavity.
Mira: They also showed a high zero phonon line fraction, ninety-eight point six plus or minus one point four percent of the total light emission.
Lev: But they flagged that their current cavity design has a low Purcell factor, so getting that performance up is the next big challenge for making this practical.
Kai: So, the title promises brightness and purity through this specific spatial control in silicon microcavities.
Mira: It really points toward how carefully we need to engineer these quantum components within the silicon chip environment.
Lev: But with those limitations, it raises a question about what kind of cavity structure actually needs to be used for true scalability.
Baptiste Lefaucher, *, Yoann Baron, *, Jean-Baptiste Jager, Vincent Calvo, Christian Elsässer, Giuliano Coppola, Frédéric Mazen, * , Sébastien Kerdilès, Félix Cache, Anaís DrĚau, Jean-Michel Gບretard, *
University of Grenoble Alpes · CEA Grenoble INP · Laboratoire Charles Coulomb, University of Montpellier and CNRS
physics.optics, quant-ph
Submitted: 2025-01-22
Updated: 2026-01-23
Journal ref: Nat. Commun. 17, 1124 (2026)
DOI: 10.1038/s41467-026-78809-x
License: http://creativecommons.org/licenses/by/4.0/
Importance score: 89/100
The gist: Bright and pure single-photon source in a silicon chip by nanoscale positioning of a color center in a microcavity is presented by fabricating an all-silicon source of near-infrared…
Key concepts
- Color Center (W Center)
- These are specific point defects created in the silicon crystal structure. They act as the emitters that produce light when excited. The researchers selectively created single W centers by using nanoholes during implantation to ensure only one emitter exists where desired.
- Silicon-on-Insulator (SOI) Microcavity
- This is a tiny optical structure made by layering silicon with a thin insulating layer on top. This structure traps and enhances the light emitted by the color center, allowing it to interact strongly with the single photon, improving its quality and brightness.
- Purcell Enhancement Factor (F)
- This factor measures how much faster an emitter emits light when placed inside a cavity compared to emitting in bulk silicon. A high F value means the emission rate is significantly boosted by the cavity, which helps in generating bright single photons.
- Antibunching ($g^{(2)}(0)$)
- This metric quantifies how 'single-photon' the light is. A value of $g^{(2)}(0) < 0.5$ indicates that only one photon is likely to be emitted at a time, confirming the source produces high-quality, non-classical single photons.
Terminology
Summary
Bright and pure single-photon source in a silicon chip by nanoscale positioning of a color center in a microcavity is presented by fabricating an all-silicon source of near-infrared linearly-polarized single photons through the nanoscale positioning of a color center in a silicon-on-insulator microcavity The results demonstrate that this method represents a major step towards on-demand sources of indistinguishable near-infrared single photons within silicon photonics chips
Source Fabrication and Characterization
The W centers are created by a well-known combination of Si+ implantation and thermal annealing The implantation is performed through a mask patterned with nanoholes whose size is tuned to locally create single W centers For a nanohole diameter of 150 nm, single W centers are observed with a yield of 40% with low background emission (g 2(0) ≈ 0.1) and average count rate of 3. p. 1 For a nanohole diameter of 150 nm, single W
centers are observed with a yield of 40% with low background emission (g
2
(0) ≈ 0. 1) and average count rate of
3.Where the paper says it
Cavity Optimization and Coupling Effects
The Purcell enhancement factor F, defined as the ratio between the emission rate in the cavity and bulk silicon, is heavily dependent on the position of the emitter A maximum enhancement factor of 13 is obtained at the center of the cavity The collection efficiency for a cavity-coupled W center was also investigated using FDTD, considering the configuration of our measurement setup A collection efficiency of 51% is obtained at the center of the cavity The spectral detuning ∆λ is the difference between the emission wavelength of the dipole and λres = 1218 nm A collection efficiency of 51% is obtained at zero-detuning, and remains above 40% in the [-20 - +10] nm detuning range
Emission Properties and Purity
The PL intensity at saturation of the W-1 spot is 1.29±0.01 Mcps together A clean antibunching dip is observed without any correction for detectors dark counts or background emission, with g(2)(0) = 0. p. 3 01
measured. A clean antibunching dip is observed without
any correction for detectors dark counts or background
emission, with g
(2)(0) = 0. 2Psat (Figure S10 in the SI), evidencing high-purity single-photon
emission up to pumping powers ensuring saturation of
the emitter. These g
(2)(0) values are among the best
reported values for Si color centers, as shown in Table
I, indicating that the source is nearly free of additional
fluorescent defects.Where the paper says it
Where the paper says it
Performance and Future Directions
Under weak pumping condition, the triggered emission of single-photon pulses is demonstrated with 93±2% purity The zero-phonon emission rate is increased by a factor F > 7.2 While point (1) and the issue of blinking have already been discussed, we see that points (2) and (3) can be radically improved by replacing our low-Fp CBG cavity by a high-Fp waveguide-coupled photonic crystal cavity The strategy is compatible with the integration of multiple single-photon sources connected to the same photonic circuit for quantum applications The bright emission of antibunched photons under CW excitation unveils the strong potential of W centers for building a deterministic SPS in SOI
Conclusion
In conclusion, we have demonstrated a source of nearinfrared linearly-polarized single photons obtained by nanoscale positioning of a W center in a SOI CBG cavity Si+ implantation through a mask patterned with nanoholes allows for selective creation of single W centers, positioned in the vicinity of the main antinode of the resonant mode The cavity-coupled emitter has a PL intensity at saturation of 1.29±0.01 Mcps together, with a g(2)(0) value inferior to 0. p. 5 The cavity-coupled emitter has a PL
intensity at saturation of 1. 01 Mcps together, with
a g
(2)(0) value inferior to 0. By Purcell enhancement of
zero-phonon emission, we obtain a photon count rate of 1. 01 Mcounts/s at saturation under
above-gap continuous-wave excitation with a Debye-Waller factor of 98. 06 under above-gap CW excitation up to P = 9. 2Psat, and with a ZPL fraction of
98.Where the paper says it
Where the paper says it
Where the paper says it
Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.
Improvements for AI systems
-
Improved AI system can deterministically generate near-infrared linearly-polarized single photons on demand through nanoscale positioning of a W center in a silicon-on-insulator microcavity. This capability overcomes limitations in generating arbitrary large entangled photon states on-chip by embedding sources of indistinguishable single photons operating on demand.
-
Improved AI system can achieve high purity single photon emission under weak pulsed laser excitation, demonstrating 93 plus 2 percent purity based on triggered emission results. This addresses the issue of poor purity due to parasitic defects observed in other silicon color centers when using similar fabrication methods.
-
Improved AI system can mitigate the detrimental effect of repumping processes at high pulsed laser power using selective pumping schemes in the future, as suggested by the paper's findings. This allows for more robust operation of on-demand sources under higher excitation conditions where blinking becomes an issue due to metastable states coupled to excited states.
-
Improved AI system can estimate the zero-phonon emission rate of a cavity-coupled emitter to be larger than 1/18 ns minus 1 second, demonstrating Purcell enhancement by a factor F greater than 7.2 compared to bulk silicon estimates. This quantitative understanding allows for accurate prediction of source performance based on the specific emitter and cavity configuration used.
-
Improved AI system can predict the effective first-lens efficiency of the source to be as low as 2.4 percent when photoblinking is taken into account under CW excitation with a repetition rate of 5 MHz. This provides a realistic assessment of achievable photon counts in practical integrated photonic chips, accounting for operational realities like emitter activity and collection losses.
-
Improved AI system can analyze the photon autocorrelation function to reveal bunching behavior (g(2)(tau) > 1) at non-zero delay under strong pumping conditions, attributing it to a metastable state coupled to the excited state of the emitter. This allows for better characterization of emitter dynamics under high excitation regimes where blinking occurs.
-
Improved AI system can optimize circular Bragg grating cavity design parameters such as disk diameter D and ring widths L1 and L2 using finite-difference time-domain simulations (FDTD). This ensures that the resonant mode is well-matched to the zero-phonon line of the W center, maximizing Purcell enhancement.
-
Improved AI system can model spectral detuning effects on collection efficiency, showing that a collection efficiency of 51 percent is obtained at zero detuning and remains above 40 percent in a specific range around the resonant wavelength. This informs optimal placement strategies for achieving high photon collection rates from the cavity mode.
Abstract
We present an all-silicon source of near-infrared linearly-polarized single photons, fabricated by nanoscale positioning of a color center in a silicon-on-insulator microcavity. The color center consists of a single W center, created at a well-defined position by Si+ ion implantation through a 150 nm-diameter nanohole in a mask. A circular Bragg grating cavity resonant with the W's zero-phonon line at 1217 nm is fabricated at the same location as the nanohole. By Purcell enhancement of zero-phonon emission, we obtain a photon count rate of 1.29 plus or minus 0.01 Mcounts/s at saturation under above-gap continuous-wave excitation with a Debye-Waller factor of 98.6 plus or minus1.4 %. A clean photon antibunching behavior is observed up to pump powers ensuring saturation of the W's emission (g(2)(0)=0.06 plus or minus0.02 at P=9.2P sat), evidencing that the density of additional parasitic fluorescent defects is very low. We also demonstrate the triggered emission of single photons with 93 plus or minus2 % purity under weak pulsed laser excitation. At high pulsed laser power, we reveal a detrimental effect of repumping processes, that could be mitigated using selective pumping schemes in the future. These results represent a major step towards on-demand sources of indistinguishable near-infrared single photons within silicon photonics chips.
Related papers
- Raman optical activity and helicity-dependent phonon splitting in chiral CoSi
- Stability and optical quality of "windmill"-formed 8CB liquid crystal films for replenishable plasma mirrors
- Experimental Scaling of Diffraction Efficiency in Laser-Induced Plasma Gratings
- Photonic Exceptional Topological Bound States in the Continuum
- SHAPE: a sparse Hamiltonian approach for prescribing eigenstates in metamaterials
- All-photonic millimeter-wave and terahertz signal core at room and cryogenic temperatures