Quasi-DNS with chemical kinetics for a single multiple-injection burner element under stable lean conditions for future gas turbine applications
summary
The gist
Gas turbine combustors for power generation increasingly operate close to lean blow-out (LBO) limits, where small changes in fuel–air mixing or flow structure can destabilize the flame and modify…
In short
This research developed a Quasi-DNS workflow using detailed methane–air chemistry to analyze near blow-out dynamics in a single element of a multiple-injection burner, modeled as a coaxial setup. The method provides insights into flame stabilization and mixing behavior crucial for understanding combustion instability in future gas turbine applications operating near lean blow-out limits.
Key concepts
- Quasi-DNS workflow
- This is a computational method that combines the accuracy of Direct Numerical Simulation (DNS) with the computational feasibility of Reynolds-Averaged Navier-Stokes (RANS). It uses high grid resolution in critical areas to capture complex fluid motions and chemical reactions, allowing for detailed analysis of flame structure and mixing.
- Lean Blow-out (LBO)
- This refers to a combustion condition where the fuel-air mixture is very lean, meaning there is a large excess of air relative to the fuel. In these conditions, small disturbances in how the fuel and air mix can easily cause the flame to become unstable or blow out.
- Scalar Dissipation Rate (SDR)
- The SDR is a diagnostic tool used in simulations to measure how intensely fluid mixing occurs within a specific region. It acts as a metric for grid resolution, helping researchers determine if the simulation mesh is fine enough to accurately capture the turbulent mixing processes that influence flame stability.
Terminology used across episodes
This episode discusses
- Quasi-DNS with chemical kinetics for a single multiple-injection burner element under stable lean conditions for future gas turbine applications · Paper Radio
The paper
Quasi-DNS with chemical kinetics for a single multiple-injection burner element under stable lean conditions for future gas turbine applications · Read on arXiv
Kazuki Abe, Youhi Morii, Kaoru Maruta
Institute of Fluid Science, Tohoku University
We develop a Quasi-DNS with chemical kinetics for a stable lean condition in a single multiple-injection burner element for future gas turbine applications, as a reusable workflow for a coaxial mixing-tube burner. Here, Quasi-DNS denotes a high-resolution, turbulence-model-free calculation; it is not DNS in the strict sense. The OpenFOAM-based method includes: (i) a simplified 30deg sector geometry capturing vortices at the mixing tube outlet, (ii) boundary conditions reproducing coaxial jets and preheated air, (iii) a reduced Correa methane-air mechanism compared with GRI 3.0 using Cantera, (iv) mesh-development and grid-sensitivity assessment based on flame structure and the squared gradient of mixture fraction, and (v) post-processing with methane-based flame index. Demonstration at an equivalence ratio phi = 0.45 shows limited in-tube mixing and strong outlet vortices, yielding a more extended heat release region than the RANS solution. - A reusable high-resolution, turbulence-model-free Quasi-DNS workflow with detailed methane-air chemistry is developed for a coaxial mixing-tube burner. - The workflow combines a reduced methane-air mechanism, refined sector-domain meshes, and scalar-field diagnostics for characterizing mixing and heat release regions. - The workflow enables analysis of mixing and flame stabilization under stable lean conditions, and provides a high-resolution numerical reference under the stated assumptions for comparison with RANS-based calculations.
DOI: 10.1016/j.mex.2026.104218
Transcript
Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.
Kai: I'm Kai.
Mira: And I'm Mira, here with Lev.
Kai: We're looking at the paper: "Quasi-DNS with chemical kinetics for a single multiple-injection burner element under stable lean conditions for future gas turbine applications".
Mira: Here's the gist of the paper. Gas turbine combustors for power generation increasingly operate close to lean blow-out (LBO) limits, where small changes in fuel–air mixing or flow structure can destabilize the flame and modify near blow-out dynamics.
Kai: The method develops a Quasi-DNS workflow with detailed methane–air chemistry for a single element of a multiple-injection burner, modeled as a coaxial burner with a mixing tube and downstream combustion chamber, as a methodological basis for near blow-out analysis in future gas turbine applications.
Mira: The workflow consists of five key steps for the Quasi-DNS approach.
Kai: These steps include defining the single-element geometry and operating conditions, prescribing inlet and outlet boundary conditions and inlet velocity profiles, selecting and validating an efficient methane–air reaction mechanism, constructing RANS and Quasi-DNS grids with verified convergence, and computing diagnostics such as scalar dissipation rate and flame indices.
Paper summary: Kai: So to recap this paper, "Quasi-DNS with chemical kinetics for a single multiple-injection burner element under stable lean conditions for future gas turbine applications," the main thesis is that as gas turbine combustors operate closer to the lean blow-out limit, small changes in fuel air mixing or flow structure can seriously destabilize the flame and modify its behavior.
Mira: It claims that conventional RANS simulations fail to capture this because they overpredict turbulent mixing and miss unsteady flame anchoring and local extinction phenomena right near the physical hardware.
Lev: The paper presents a Quasi-DNS workflow with detailed methane air chemistry on a coaxial burner with a mixing tube, which is designed specifically to test the limitations of RANS-based design calculations in these lean blow-out relevant elements.
Kai: It matters because it provides a step by step workflow that can be directly adapted to other burner configurations that have mixing tubes in gas turbine combustors, which helps engineers understand where RANS might fall short.
Mira: The method combines validated reduced kinetics, grid converged three dimensional sector meshes, and uses scalar diagnostics like the scalar dissipation rate and flame index to characterize the combustion modes.
Lev: They are building this workflow for direct reuse in other studies involving mixing-tube burner elements, which suggests it's a practical tool for testing design assumptions.
Kai: The paper sets up a system that combines validated reduced kinetics with grid converged three dimensional sector meshes and uses scalar diagnostics such as the scalar dissipation rate and flame index to characterize the combustion modes.
Mira: They use the reactingFoam solver in OpenFOAM v1706 for this transient Quasi-DNS approach with detailed chemistry to analyze methane air combustion.
Lev: The entire step by step workflow, including grid construction, mechanism validation and post processing scripts, is designed for direct reuse in other burner configurations with mixing tubes in gas turbine combustors.
Kai: So the core idea is developing this specific setup that combines validated reduced kinetics with grid converged three dimensional sector meshes and uses scalar diagnostics such as the scalar dissipation rate and flame index to characterize the combustion modes.
Mira: This approach allows them to show how Quasi-DNS reveals mixing and flame anchoring at the mixing tube outlet that RANS does not capture for this specific burner element.
Lev: The paper shows they are using a reactingFoam solver in OpenFOAM v1706 for this transient Quasi-DNS approach with detailed chemistry to analyze methane air combustion.
Kai: This whole process is designed for direct reuse in other burner configurations with mixing tubes in gas turbine combustors.
Mira: The method combines validated reduced kinetics, grid converged three dimensional sector meshes, and uses scalar diagnostics such as the scalar dissipation rate and flame index to characterize the combustion modes.
Conclusion: Kai: Looking at the title, "Quasi-DNS with chemical kinetics for a single multiple-injection burner element under stable lean conditions for future gas turbine applications," it points directly at the focus: using high fidelity simulation to understand how these specific burner elements perform under lean conditions.
Mira: The authors are Kazuki Abe, Youhi Morii, and Kaoru Maruta, and their work is important because they address the pressure we have to achieve higher efficiency and lower emissions while keeping systems stable.
Lev: What this means in simple terms is that when we design these burners for future gas turbine applications, especially those using low carbon fuels like hydrogen, engineers need methods that go beyond standard RANS predictions.
Kai: They are advocating for a method where you can see the spatial variations in combustion mode near the mixing layer that are missed by RANS, which is crucial for understanding flame anchoring issues under lean conditions.
Mira: The implication is that if we want to design better low-NOx systems, we need to use tools like this Quasi-DNS approach to accurately predict how the flame will actually behave in those tricky near blow-out regions.
Lev: Essentially, it tells designers that for applications involving mixing tubes and lean operation, RANS gives a limited picture because you need a method that captures the unsteady physics happening at the boundary.
Kai: It pushes for using these high fidelity tools when analyzing burner elements to make sure we aren't designing systems that are unstable when they operate close to their operational limits.
More episodes
- 2611.14082-Two atoms with strong light-induced dipolar interactions
- 2611.14040-Characterization of BNLs 20 and 30 micrometer thick LGADs for the Electron Ion Collider
- 2611.13399-Lift-element-based dynamic network of vortex gust-airfoil interactions
- 2611.13476-Hopfion Superlattices in 3D Twisted Moir'e Light Fields
- 2611.13642-Investigation of the timing performance of double-sided p-type 3D silicon sensors produced by CNM
- 2611.13830-SiPM optical readout of a PICOSEC Micromegas precise timing detector
- 2611.14152-Where are the shortest-path nodes in spatial networks?
- 2611.14219-Sub-Ice: semi-automated mapping of basal channels from ice shelf surface elevation data
- 2611.16341-SUMNO: Spatially Unrolled Multigrid Neural Operator for Fluid Flow Surrogates
- 2611.16090-Multi-UTE Myelin Fraction Mapping: Repeatability and Cross-Field-Strength Reproducibility at 1.5T and 3T