Control of deterministic breakdown to turbulence of hypersonic boundary layer with spanwise non-uniform surface temperature
summary
The gist
Direct Numerical Simulation (DNS) of a Mach 6 boundary layer over a flat plate is performed to assess the effect of spanwise non-uniform surface temperature on breakdown to turbulence under…
In short
Direct Numerical Simulation (DNS) of a Mach 6 boundary layer was used to study how non-uniform surface temperature affects breakdown to turbulence under fixed conditions. The research found that weak control streaks, generated by varying surface temperature across the span, can stabilize the second Mack mode, reducing high-frequency shear stress by about 30% and delaying transition. This stabilization also reduces mean and peak heat transfer.
Key concepts
- Mack Modes
- These are different wave-like solutions that arise in compressible boundary layers when the flow Mach number is greater than one. The second Mack mode is particularly important in hypersonic flight between Mach 4 and 6, playing a key role in the initial transition to turbulence.
- Control Streaks
- These are streaks generated by intentionally creating a non-uniform surface temperature distribution across the span of the boundary layer. These streaks act as control mechanisms that can interact with flow instabilities to stabilize them and prevent premature breakdown to turbulence.
- Heat Transfer Reduction
- The study quantified how controlling the transition delay affects aerodynamic heating. By stabilizing these modes, the researchers found that mean heat transfer is reduced by about 15% and high-frequency peak heat transfer by 34% in scenarios dominated by both Mack modes.
Terminology used across episodes
This episode discusses
- Control of deterministic breakdown to turbulence of hypersonic boundary layer with spanwise non-uniform surface temperature · Paper Radio
The paper
Control of deterministic breakdown to turbulence of hypersonic boundary layer with spanwise non-uniform surface temperature · Read on arXiv
Department of Aeronautics, Imperial College London · School of Mechanical Engineering Sciences, University of Surrey
Direct Numerical Simulation (DNS) of a Mach 6 boundary layer over a flat plate is performed to assess the effect of spanwise non-uniform surface temperature on breakdown to turbulence under deterministic forcing. The streamwise location of laminar to turbulent transition in hypersonic boundary layers has a significant influence on viscous drag and aerodynamic heating of external surfaces of hypersonic vehicles. Previous work investigated the stabilization of hypersonic boundary layers by optimally growing streaks. More recently, DNS for a hypersonic boundary layer showed that it is possible to generate streaks through a spanwise non-uniform surface temperature distribution. The laminar computations showed the control method can stabilize the second Mack mode and it is robust across a range of Mach numbers and wall temperature ratios. In this work, two scenarios are investigated where two-dimensional (second Mack mode) and oblique (first Mack mode) disturbances dominate the initial linear stage of transition. It is found that weak control streaks with amplitude below 5% of the freestream velocity can reduce high-frequency shear-stress due to the second Mack mode by approximately 30% relative to the uncontrolled configuration, and delay transition. For first Mack mode dominated breakdown, the control streaks have no effect on transition location, but the peak amplitude of the spanwise-integrated wall heat flux is reduced. For the first and second Mack mode-dominated scenarios, the mean and high-frequency peak heat transfer are reduced approximately by 15% and 34%, respectively. The dominant mechanisms are identified and attributed to the pressure work contribution to turbulent kinetic energy and the second Mack mode dilatation work.
DOI: 10.1103/vqjs-1wr8
Transcript
Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.
Kai: We're looking at the paper: "Control of deterministic breakdown to turbulence of hypersonic boundary layer with spanwise non-uniform surface temperature".
Mira: Here's the gist of the paper. Direct Numerical Simulation (DNS) of a Mach 6 boundary layer over a flat plate is performed to assess the effect of spanwise non-uniform surface temperature on breakdown to turbulence under deterministic forcing.
Kai: The laminar computations showed that the control method can stabilize the second Mack mode and it is robust across a range of Mach numbers and wall temperature ratios.
Mira: The development of aerospace technologies that travel with a flight Mach number (M∞) well above sonic is challenged by complex aerothermodynamic behaviors.
Kai: For laminar hypersonic boundary layers, an important non dimensional parameter is the relative Mach number M, which is defined based on the velocity of the flow (u) relative to the phase speed (cph) of the hydrodynamic instability within the boundary layer.
Paper summary: Kai: To recap, this paper is performing direct numerical simulation on a Mach six boundary layer over a flat plate to see how non-uniform surface temperature affects breakdown to turbulence under deterministic forcing <ref:2604.22545#pg2,a Mach 6 boundary layer over a flat plate>. The core thesis is that by using a spanwise non-uniform surface temperature distribution, you can generate streaks that control the transition to turbulence.
Mira: They specifically investigated two scenarios: one where the two-dimensional second Mack mode dominates, and another where the oblique first Mack mode dominates in the initial linear stage of transition.
Lev: The paper claims that weak control streaks, specifically those with an amplitude below five percent of freestream velocity, can reduce high frequency shear stress by about thirty percent for the second Mack mode.
Kai: That reduction in high frequency shear stress is tied to delaying the transition location in those specific cases and reducing aerodynamic heating.
Mira: They also found that while control streaks don't change the transition location when the first Mack mode dominates, they do reduce the peak amplitude of wall heat flux, and for both modes, they cut mean heat transfer by about fifteen percent and high frequency peak heat transfer by about thirty-four percent.
Lev: The underlying physical mechanism they identified involves pressure work contribution to turbulent kinetic energy and dilatation work from the second Mack mode.
Kai: So the paper is essentially showing that this temperature modulation has a measurable effect on both the timing of transition and the intensity of heating, depending on which instability mode is active.
Mira: It’s a demonstration that we can generate streaks through a spanwise non-uniform surface temperature distribution, which was something they showed was possible through previous work.
Lev: The paper also highlights that this control method is robust across different Mach numbers and wall temperature ratios, which suggests it's not overly dependent on one specific setup parameter.
Kai: So the key finding is that this deterministic forcing allows us to actively stabilize the second Mack mode using these streaks, and the results are quite robust.
Conclusion: Kai: So, looking at this paper, "Control of deterministic breakdown to turbulence of hypersonic boundary layer with spanwise non-uniform surface temperature," the authors Luca Boscagli, Georgios Rigas, and Paul J. K. Bruce have shown a specific way to use thermal control for hypersonic boundary layers.
Mira: They've demonstrated that manipulating the surface temperature across the span allows you to generate streaks that interact with instabilities like the second Mack mode to manage how the flow transitions to turbulence.
Lev: The implication here is that for designing things like hypersonic vehicles, we can predict where and how much heat transfer will occur by knowing this control method works.
Kai: It means we can design surfaces that are less susceptible to those instabilities by implementing this surface temperature non-uniformity before the breakdown happens.
Mira: It moves the discussion forward by showing that deterministic forcing can be a way to actively manage these boundary layer behaviors rather than just waiting for them to happen naturally.
Lev: From my view, it's a practical tool because it gives us concrete numbers on how much stabilization we get for different modes, which is exactly what you need when you are building real hardware.
More episodes
- 2611.14082-Two atoms with strong light-induced dipolar interactions
- 2611.14040-Characterization of BNLs 20 and 30 micrometer thick LGADs for the Electron Ion Collider
- 2611.13399-Lift-element-based dynamic network of vortex gust-airfoil interactions
- 2611.13476-Hopfion Superlattices in 3D Twisted Moir'e Light Fields
- 2611.13642-Investigation of the timing performance of double-sided p-type 3D silicon sensors produced by CNM
- 2611.13830-SiPM optical readout of a PICOSEC Micromegas precise timing detector
- 2611.14152-Where are the shortest-path nodes in spatial networks?
- 2611.14219-Sub-Ice: semi-automated mapping of basal channels from ice shelf surface elevation data
- 2611.16341-SUMNO: Spatially Unrolled Multigrid Neural Operator for Fluid Flow Surrogates
- 2611.16090-Multi-UTE Myelin Fraction Mapping: Repeatability and Cross-Field-Strength Reproducibility at 1.5T and 3T