Control of deterministic breakdown to turbulence of hypersonic boundary layer with spanwise non-uniform surface temperature

arXiv:2604.22545 · physics.flu-dyn · Submitted 2026-04-24 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: We're looking at the paper: "Control of deterministic breakdown to turbulence of hypersonic boundary layer with spanwise non-uniform surface temperature".

Mira: Here's the gist of the paper. Direct Numerical Simulation (DNS) of a Mach 6 boundary layer over a flat plate is performed to assess the effect of spanwise non-uniform surface temperature on breakdown to turbulence under deterministic forcing.

Kai: The laminar computations showed that the control method can stabilize the second Mack mode and it is robust across a range of Mach numbers and wall temperature ratios.

Mira: The development of aerospace technologies that travel with a flight Mach number (M∞) well above sonic is challenged by complex aerothermodynamic behaviors.

Kai: For laminar hypersonic boundary layers, an important non dimensional parameter is the relative Mach number M, which is defined based on the velocity of the flow (u) relative to the phase speed (cph) of the hydrodynamic instability within the boundary layer.

Paper summary: Kai: To recap, this paper is performing direct numerical simulation on a Mach six boundary layer over a flat plate to see how non-uniform surface temperature affects breakdown to turbulence under deterministic forcing <ref:2604.22545#pg2,a Mach 6 boundary layer over a flat plate>. The core thesis is that by using a spanwise non-uniform surface temperature distribution, you can generate streaks that control the transition to turbulence.

Mira: They specifically investigated two scenarios: one where the two-dimensional second Mack mode dominates, and another where the oblique first Mack mode dominates in the initial linear stage of transition.

Lev: The paper claims that weak control streaks, specifically those with an amplitude below five percent of freestream velocity, can reduce high frequency shear stress by about thirty percent for the second Mack mode.

Kai: That reduction in high frequency shear stress is tied to delaying the transition location in those specific cases and reducing aerodynamic heating.

Mira: They also found that while control streaks don't change the transition location when the first Mack mode dominates, they do reduce the peak amplitude of wall heat flux, and for both modes, they cut mean heat transfer by about fifteen percent and high frequency peak heat transfer by about thirty-four percent.

Lev: The underlying physical mechanism they identified involves pressure work contribution to turbulent kinetic energy and dilatation work from the second Mack mode.

Kai: So the paper is essentially showing that this temperature modulation has a measurable effect on both the timing of transition and the intensity of heating, depending on which instability mode is active.

Mira: It’s a demonstration that we can generate streaks through a spanwise non-uniform surface temperature distribution, which was something they showed was possible through previous work.

Lev: The paper also highlights that this control method is robust across different Mach numbers and wall temperature ratios, which suggests it's not overly dependent on one specific setup parameter.

Kai: So the key finding is that this deterministic forcing allows us to actively stabilize the second Mack mode using these streaks, and the results are quite robust.

Conclusion: Kai: So, looking at this paper, "Control of deterministic breakdown to turbulence of hypersonic boundary layer with spanwise non-uniform surface temperature," the authors Luca Boscagli, Georgios Rigas, and Paul J. K. Bruce have shown a specific way to use thermal control for hypersonic boundary layers.

Mira: They've demonstrated that manipulating the surface temperature across the span allows you to generate streaks that interact with instabilities like the second Mack mode to manage how the flow transitions to turbulence.

Lev: The implication here is that for designing things like hypersonic vehicles, we can predict where and how much heat transfer will occur by knowing this control method works.

Kai: It means we can design surfaces that are less susceptible to those instabilities by implementing this surface temperature non-uniformity before the breakdown happens.

Mira: It moves the discussion forward by showing that deterministic forcing can be a way to actively manage these boundary layer behaviors rather than just waiting for them to happen naturally.

Lev: From my view, it's a practical tool because it gives us concrete numbers on how much stabilization we get for different modes, which is exactly what you need when you are building real hardware.

Department of Aeronautics, Imperial College London · School of Mechanical Engineering Sciences, University of Surrey

physics.flu-dyn

Submitted: 2026-04-24

Updated: 2026-09-28

DOI: 10.1103/vqjs-1wr8

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 80/100

The gist: Direct Numerical Simulation (DNS) of a Mach 6 boundary layer over a flat plate is performed to assess the effect of spanwise non-uniform surface temperature on breakdown to turbulence under…

Key concepts

Mack Modes
These are different wave-like solutions that arise in compressible boundary layers when the flow Mach number is greater than one. The second Mack mode is particularly important in hypersonic flight between Mach 4 and 6, playing a key role in the initial transition to turbulence.
Control Streaks
These are streaks generated by intentionally creating a non-uniform surface temperature distribution across the span of the boundary layer. These streaks act as control mechanisms that can interact with flow instabilities to stabilize them and prevent premature breakdown to turbulence.
Heat Transfer Reduction
The study quantified how controlling the transition delay affects aerodynamic heating. By stabilizing these modes, the researchers found that mean heat transfer is reduced by about 15% and high-frequency peak heat transfer by 34% in scenarios dominated by both Mack modes.

Terminology

Summary

Direct Numerical Simulation (DNS) of a Mach 6 boundary layer over a flat plate is performed to assess the effect of spanwise non-uniform surface temperature on breakdown to turbulence under deterministic forcing. p. 1

Where the paper says it

Abstract Direct Numerical Simulation (DNS) of a Mach 6 boundary layer over a flat plate is performed to assess the effect of spanwise non-uniform surface temperature on breakdown to turbulence under deterministic forcing. The streamwise location of laminar to turbulent transition in hypersonic boundary layers has a significant influence on viscous drag and aerodynamic heating of external surfaces of hypersonic vehicles.

The laminar computations showed that the control method can stabilize the second Mack mode and it is robust across a range of Mach numbers and wall temperature ratios. p. 1
Where the paper says it

More recently, DNS for a hypersonic boundary layer showed that it is possible to generate streaks through a spanwise non-uniform surface temperature distribution. The laminar computations showed the control method can stabilize the second Mack mode and it is robust across a range of Mach numbers and wall temperature ratios.

Introduction to Hypersonic Boundary Layer Instabilities

The development of aerospace technologies that travel with a flight Mach number (M∞) well above sonic is challenged by complex aerothermodynamic behaviors. For laminar hypersonic boundary layers, an important non dimensional parameter is the relative Mach number M, which is defined based on the velocity of the flow (u) relative to the phase speed (cph) of the hydrodynamic instability within the boundary layer. p. 1

Where the paper says it

Boundary layer instability and transition can significantly affect the flight envelope and operability limits of hypersonic vehicles [1]. For laminar hypersonic boundary layers, an important non dimensional parameter is the relative Mach number 𝑀, which is defined based on the velocity of the flow (𝑢) relative to the phase speed (𝑐𝑝ℎ) of the hydrodynamic instability within the boundary layer.

When M2 > 1, the compressible counterpart of Rayleigh’s equation admits multiple wave-like solutions, also referred to as higher Mack modes. p. 1
Where the paper says it

For laminar hypersonic boundary layers, an important non dimensional parameter is the relative Mach number 𝑀, which is defined based on the velocity of the flow (𝑢) relative to the phase speed (𝑐𝑝ℎ) of the hydrodynamic instability within the boundary layer. When 𝑀 2 > 1, the compressible counterpart of Rayleigh’s equation admits multiple wave-like solutions, also referred to as higher Mack modes [2].

For a flight Mach number ∗l. p. 1
Where the paper says it

The dominant mechanisms are identified and attributed to the pressure work contribution to turbulent kinetic energy and the second Mack mode dilatation work. INTRODUCTION The development of aerospace technologies that travel with a flight Mach number (𝑀∞) well above sonic is challenged by complex aerothermodynamic behaviors.

boscagli@imperial. p. 0
Where the paper says it

Control of deterministic breakdown to turbulence of hypersonic boundary layer with spanwise non-uniform surface temperature Luca Boscagli,∗ Georgios Rigas, and Paul J. Bruce Department of Aeronautics, Imperial College London, London, London, UK Olaf Marxen School of Mechanical Engineering Sciences, University of Surrey, Guildford, UK 1 arXiv:2604.

ac.uk between 4 and 6, a two-dimensional instability mode (second Mack mode) plays an important role within the initial linear transition stage. p. 2
Where the paper says it

between 4 and 6, a two-dimensional instability mode (second Mack mode) plays an important role within the initial linear transition stage. However, the route to turbulence in hypersonic boundary layers at flight relevant conditions is poorly understood [3], and this challenges the development of effective control strategies.

However, the route to turbulence in hypersonic boundary layers at flight relevant conditions is poorly understood. p. 2
Where the paper says it

between 4 and 6, a two-dimensional instability mode (second Mack mode) plays an important role within the initial linear transition stage. However, the route to turbulence in hypersonic boundary layers at flight relevant conditions is poorly understood [3], and this challenges the development of effective control strategies.

Stabilization Mechanisms and Control Streaks

Previous work investigated the stabilization of hypersonic boundary layers by optimally growing streaks. More recently, DNS for a hypersonic boundary layer showed that it is possible to generate streaks through a spanwise non-uniform surface temperature distribution. p. 1

Where the paper says it

Previous work investigated the stabilization of hypersonic boundary layers by optimally growing streaks. More recently, DNS for a hypersonic boundary layer showed that it is possible to generate streaks through a spanwise non-uniform surface temperature distribution.

The laminar computations showed the control method can stabilize the second Mack mode and it is robust across a range of Mach numbers and wall temperature ratios. p. 1
Where the paper says it

More recently, DNS for a hypersonic boundary layer showed that it is possible to generate streaks through a spanwise non-uniform surface temperature distribution. The laminar computations showed the control method can stabilize the second Mack mode and it is robust across a range of Mach numbers and wall temperature ratios.

In this work, two scenarios are investigated where two-dimensional (second Mack mode) and oblique (first Mack mode) disturbances dominate the initial linear stage of transition. p. 1
Where the paper says it

The laminar computations showed the control method can stabilize the second Mack mode and it is robust across a range of Mach numbers and wall temperature ratios. In this work, two scenarios are investigated where two-dimensional (second Mack mode) and oblique (first Mack mode) disturbances dominate the initial linear stage of transition.

It is found that weak control streaks with amplitude below 5% of the freestream velocity can reduce high-frequency shear-stress due to the second Mack mode by approximately 30% relative to the uncontrolled configuration, and delay transition. p. 1
Where the paper says it

In this work, two scenarios are investigated where two-dimensional (second Mack mode) and oblique (first Mack mode) disturbances dominate the initial linear stage of transition. It is found that weak control streaks with amplitude below 5% of the freestream velocity can reduce high-frequency shear-stress due to the second Mack mode by approximately 30% relative to the uncontrolled configuration, and delay transition.

Effect on Heat Transfer and Transition Delay

For first Mack mode dominated breakdown, the control streaks have no effect on transition location, but the peak amplitude of the spanwise-integrated wall heat flux is reduced. For the first and second Mack mode-dominated scenarios, the mean and high-frequency peak heat transfer are reduced approximately by 15% and 34%, respectively. p. 1

Where the paper says it

For first Mack mode dominated breakdown, the control streaks have no effect on transition location, but the peak amplitude of the spanwise-integrated wall heat flux is reduced. For the first and second Mack mode-dominated scenarios, the mean and high-frequency peak heat transfer are reduced approximately by 15% and 34%, respectively.

The dominant mechanisms are identified and attributed to the pressure work contribution to turbulent kinetic energy and the second Mack mode dilatation work. p. 1
Where the paper says it

For the first and second Mack mode-dominated scenarios, the mean and high-frequency peak heat transfer are reduced approximately by 15% and 34%, respectively. The dominant mechanisms are identified and attributed to the pressure work contribution to turbulent kinetic energy and the second Mack mode dilatation work.

In the case of second Mack mode fundamental resonance (SMF), weak control-streaks do not affect the magnitude of the heat transfer overshoot, but only the streamwise location as a result of the delayed laminar to turbulence transition. p. 3
Where the paper says it

[23], which focused on laminarregime stabilization of the second Mack mode, the present study addresses the transition process itself, including nonlinear breakdown and turbulence onset under conditions where both first- and second-mode mechanisms can be dominant, and the effect of the control-streaks on heat-transfer peaks. Section II presents the case study, computational domain and numerical methods used.

Sensitivity to Control Parameters

The control method is spanwise invariant to changes in theta, and this is further indication that for this configuration the MFD dominates the stabilization mechanism. The beneficial effects of the control method on the reduction of total pressure and temperature losses via a delayed transition to turbulence are further evaluated based on an isentropic efficiency, which is quantified with the entropy function (zeta). The control method delays the efficiency losses due to transition to turbulence further downstream compared to the uncontrolled configuration (Fig. p. 1

Where the paper says it

In this work, two scenarios are investigated where two-dimensional (second Mack mode) and oblique (first Mack mode) disturbances dominate the initial linear stage of transition. It is found that weak control streaks with amplitude below 5% of the freestream velocity can reduce high-frequency shear-stress due to the second Mack mode by approximately 30% relative to the uncontrolled configuration, and delay transition.

6).

Conclusion on Control Effectiveness

Overall, the control method is effective for second Mack mode dominated transition to turbulence scenarios. The weak control-streaks can delay transition to turbulence and for the range of configurations investigated the delay is approximately 40 to 60 times the local boundary layer thickness. p. 2

Where the paper says it

This can be passively attained through the use of alternate stripes of materials with different thermal properties, and by exploiting the high heat flux characteristics of the hypersonic regime. Effective stabilization of the second Mack mode through the novel control method can be attained using streaks with a wavelength that is approximately 8-10 times the local boundary layer thickness [22].

For first Mack mode oblique breakdown, optimal (based on the existing literature) and non-optimal spanwise wavelengths of the control-streak have been investigated. p. 8
Where the paper says it

Two laminar to turbulence transition scenarios are investigated, namely second Mack mode fundamental resonance (SMF) and first Mack mode oblique (FMO) breakdown [3]. The choice of the timestep for both configurations is based upon previous work [3, 33].

Overall, the work showed that the weak optimal streaks can stabilize the first Mack mode, but there is no effect on transition to turbulence. p. 3
Where the paper says it

For a wavelength of the control streaks close to the value for optimal transient growth (𝜆𝑧,𝑜 𝑝𝑡), the three-dimensional steady deformation of the streaks becomes effective to suppress the growth of the oblique waves. Overall, the aim of this work is to assess, via Direct Numerical Simulations (DNS), the effect of streaks generated through non-uniform surface temperature distributions on boundary layer stability and transition to turbulence.

Impact on Aerodynamic Heating

For the second Mack mode fundamental resonance scenario it is shown that the control-streaks stabilize the second Mack mode, reducing the high-frequency (second Mack mode related) peaks in the skin friction coefficient. For control-streaks with an amplitude of approximately 3. p. 1

Where the paper says it

In this work, two scenarios are investigated where two-dimensional (second Mack mode) and oblique (first Mack mode) disturbances dominate the initial linear stage of transition. It is found that weak control streaks with amplitude below 5% of the freestream velocity can reduce high-frequency shear-stress due to the second Mack mode by approximately 30% relative to the uncontrolled configuration, and delay transition.

5% of the freestream speed this reduction can be up to 30% relative to the uncontrolled configuration. p. 1
Where the paper says it

In this work, two scenarios are investigated where two-dimensional (second Mack mode) and oblique (first Mack mode) disturbances dominate the initial linear stage of transition. It is found that weak control streaks with amplitude below 5% of the freestream velocity can reduce high-frequency shear-stress due to the second Mack mode by approximately 30% relative to the uncontrolled configuration, and delay transition.

In agreement with previous studies, there is no overshoot for second Mack mode dominated breakdown to turbulence, and this is not affected by the control-streaks. p. 1
Where the paper says it

It is found that weak control streaks with amplitude below 5% of the freestream velocity can reduce high-frequency shear-stress due to the second Mack mode by approximately 30% relative to the uncontrolled configuration, and delay transition. For first Mack mode dominated breakdown, the control streaks have no effect on transition location, but the peak amplitude of the spanwise-integrated wall heat flux is reduced.

For first Mack mode oblique breakdown, it is found that control-streaks with relatively low amplitude (below 5%) are able to reduce the overshoot by up to 15%. p. 1
Where the paper says it

It is found that weak control streaks with amplitude below 5% of the freestream velocity can reduce high-frequency shear-stress due to the second Mack mode by approximately 30% relative to the uncontrolled configuration, and delay transition. For first Mack mode dominated breakdown, the control streaks have no effect on transition location, but the peak amplitude of the spanwise-integrated wall heat flux is reduced.

Novel Contributions

To the authors’ knowledge, the effect of control streaks on mean and fluctuating heat-transfer peaks has never been reported before, and it is a novel contribution of this work, specifically for weak control-streaks generated through thermal modulation. The insights gained here provide guidelines for further optimization of this control strategy and its integration into future hypersonic vehicle designs. p. 6

Where the paper says it

As further detailed in Marxen et al. [15], for the spatial discretization and the time integration a nominally 6 𝑡ℎ order compact finite difference scheme and an explicit 3𝑟 𝑑 order Runge-Kutta method are used, respectively.

Appendix Details

The grid resolution is quantified relative to the Kolmogorov length scale (eq. 20) through Δxeta, Δyeta, Δzeta, (A1). Rarefaction effects are assessed using the Knudsen number (Kneta) based on the Kolmogorov length scale, as defined in equation 23. p. 1

Where the paper says it

For laminar hypersonic boundary layers, an important non dimensional parameter is the relative Mach number 𝑀, which is defined based on the velocity of the flow (𝑢) relative to the phase speed (𝑐𝑝ℎ) of the hydrodynamic instability within the boundary layer. When 𝑀 2 > 1, the compressible counterpart of Rayleigh’s equation admits multiple wave-like solutions, also referred to as higher Mack modes [2].

Statistical convergence is evaluated from running means of volume-averaged (⟨·⟩V) terms. p. 9
Where the paper says it

4) are used. To achieve statistical convergence, the computations for the uncontrolled configurations are advanced in time for approximately 1.

The normalized residual is defined as ResN = maxi Ti,N. p. 6
Where the paper says it

The freestream Mach number is defined as 𝑀∞ = 𝑢˜∞/𝑐˜∞. In the rest of the manuscript, velocity and temperature scales are normalized with the freestream velocity, ˜𝑢∞, and static temperature, 𝑇˜∞, respectively.

Appendix C on Phase Effects

It is shown that the control method delays transition via a stabilization of the second Mack mode, and preserving the symmetries of the flow for a longer streamwise extent. The effectiveness of the method is here investigated for a configuration with theta = pi/4 and compared to the baseline configuration with theta = 0. p. 9

Where the paper says it

The wall temperature boundary condition is 𝑇𝑤 = 𝑇𝑤,𝑏𝑎𝑠𝑒 1 + 𝐴𝑇𝑤 sin (𝑘𝑠𝑧 + 𝜃) , (11) where 𝐴𝑇𝑤 sets the amplitude of the wall temperature variation relative to the baseline (uniform) wall temperature, 𝑘𝑠 = 2𝜋/𝜆𝑧,𝑠 sets the fundamental spanwise wavenumber of the control streaks, and 𝜃 ∈ [0, 2𝜋] is used to control the relative phase between the wall temperature and the disturbance forcing boundary conditions. The parameter 𝜃 is set to zero for most of the investigations, but for the studies presented in appendix C, that investigate the effect of changes in spanwise phase on the control method effectiveness.

It is shown that this constructive interference is not the result of a mathematical construct due to the zero relative spanwise phase (theta in equation (11)) between the control law and the forcing disturbance (equation (10)). p. 9
Where the paper says it

The mathematical definition is largely based on our previous work [22, 23]. The wall temperature boundary condition is 𝑇𝑤 = 𝑇𝑤,𝑏𝑎𝑠𝑒 1 + 𝐴𝑇𝑤 sin (𝑘𝑠𝑧 + 𝜃) , (11) where 𝐴𝑇𝑤 sets the amplitude of the wall temperature variation relative to the baseline (uniform) wall temperature, 𝑘𝑠 = 2𝜋/𝜆𝑧,𝑠 sets the fundamental spanwise wavenumber of the control streaks, and 𝜃 ∈ [0, 2𝜋] is used to control the relative phase between the wall temperature and the disturbance forcing boundary conditions.

The effectiveness of the method is unaffected by mistuning between control and disturbance forcing. p. 9
Where the paper says it

The wall temperature boundary condition is 𝑇𝑤 = 𝑇𝑤,𝑏𝑎𝑠𝑒 1 + 𝐴𝑇𝑤 sin (𝑘𝑠𝑧 + 𝜃) , (11) where 𝐴𝑇𝑤 sets the amplitude of the wall temperature variation relative to the baseline (uniform) wall temperature, 𝑘𝑠 = 2𝜋/𝜆𝑧,𝑠 sets the fundamental spanwise wavenumber of the control streaks, and 𝜃 ∈ [0, 2𝜋] is used to control the relative phase between the wall temperature and the disturbance forcing boundary conditions. The parameter 𝜃 is set to zero for most of the investigations, but for the studies presented in appendix C, that investigate the effect of changes in spanwise phase on the control method effectiveness.

Appendix B on Symmetry Preservation

The heated streaks preserve the spanwise symmetry of the flow for longer streamwise distances. The control method preserves the symmetry for a longer streamwise distance, which is approximately 140δ99,in. p. 3

Where the paper says it

Sharma et al. [11] showed that most effective control-streaks had amplitudes approximately in the range of 10 to 20% of the freestream streamwise momentum ( ˜𝜌𝑢∞), and wavelength 1/5 𝑡ℎ to 1/4 𝑡ℎ of the fundamental oblique mode .

Appendix A on Scale Resolution

The initial peak in figure 23 corresponds to the disturbance forcing region (x ∈ [15, 20]). p. 7

Where the paper says it

The control region is applied as a boundary condition at the wall and is indicated by the alternate red-blue spanwise pattern. Deterministic forcing is applied as a blowing-suction boundary condition and indicated by the label disturbance forcing region.

The maximum local Knudsen number based on the Kolmogorov length scale is approximately Kneta = λ/e ≈ 0. p. 6
Where the paper says it

𝑃𝑟∞ = 𝜇˜∞𝑐˜𝑝/ ˜𝑘𝑡ℎ,∞ , (8) where ˜𝜌∞, ˜𝑐∞, ˜𝜇∞ and ˜𝑘𝑡ℎ,∞ are the freestream density, speed of sound, dynamic viscosity and thermal conductivity, respectively, 𝐿˜ 𝑟𝑒 𝑓 (= 6. 20 × 10−4m) is the reference length scale, and ˜𝑐𝑝 is the specific heat at constant pressure.

p. 6
Where the paper says it

𝑃𝑟∞ = 𝜇˜∞𝑐˜𝑝/ ˜𝑘𝑡ℎ,∞ , (8) where ˜𝜌∞, ˜𝑐∞, ˜𝜇∞ and ˜𝑘𝑡ℎ,∞ are the freestream density, speed of sound, dynamic viscosity and thermal conductivity, respectively, 𝐿˜ 𝑟𝑒 𝑓 (= 6. 20 × 10−4m) is the reference length scale, and ˜𝑐𝑝 is the specific heat at constant pressure.

29, occurring only within a narrow region adjacent to the wall. p. 8
Where the paper says it

Wall blowing and suction is used to force transition to turbulence within the computational domain; this boundary condition is sometimes referred to as actuator in the rest of the manuscript. The wall-normal profile implemented as the boundary condition in the disturbance forcing region is expressed as    𝑣˜𝑤 𝑐˜∞ = 𝑣𝑤 = exp − √ 2 2 𝜉 2 𝑔(𝑧) Í 𝑖 𝐴𝑖 sin (𝜔𝑖 𝑡 − 𝑘𝑖𝑧) 𝑔(𝑧) = 1.

p. 8
Where the paper says it

Wall blowing and suction is used to force transition to turbulence within the computational domain; this boundary condition is sometimes referred to as actuator in the rest of the manuscript. The wall-normal profile implemented as the boundary condition in the disturbance forcing region is expressed as    𝑣˜𝑤 𝑐˜∞ = 𝑣𝑤 = exp − √ 2 2 𝜉 2 𝑔(𝑧) Í 𝑖 𝐴𝑖 sin (𝜔𝑖 𝑡 − 𝑘𝑖𝑧) 𝑔(𝑧) = 1.

The global Knudsen number remains Kn ≈ 2. p. 1
Where the paper says it

The dominant mechanisms are identified and attributed to the pressure work contribution to turbulent kinetic energy and the second Mack mode dilatation work. INTRODUCTION The development of aerospace technologies that travel with a flight Mach number (𝑀∞) well above sonic is challenged by complex aerothermodynamic behaviors.

p. 1
Where the paper says it

The dominant mechanisms are identified and attributed to the pressure work contribution to turbulent kinetic energy and the second Mack mode dilatation work. INTRODUCTION The development of aerospace technologies that travel with a flight Mach number (𝑀∞) well above sonic is challenged by complex aerothermodynamic behaviors.

03×10−3.

The rapid growth of the amplitude of the control-streaks due to the interaction with the 3D oblique waves, and the control streaks not being sufficiently strong to achieve an effective stabilization of the latter. The effect of spanwise phase is investigated for a configuration with theta =pi/4 and compared to the baseline configuration with theta = 0. p. 9

Where the paper says it

The wall temperature boundary condition is 𝑇𝑤 = 𝑇𝑤,𝑏𝑎𝑠𝑒 1 + 𝐴𝑇𝑤 sin (𝑘𝑠𝑧 + 𝜃) , (11) where 𝐴𝑇𝑤 sets the amplitude of the wall temperature variation relative to the baseline (uniform) wall temperature, 𝑘𝑠 = 2𝜋/𝜆𝑧,𝑠 sets the fundamental spanwise wavenumber of the control streaks, and 𝜃 ∈ [0, 2𝜋] is used to control the relative phase between the wall temperature and the disturbance forcing boundary conditions. The parameter 𝜃 is set to zero for most of the investigations, but for the studies presented in appendix C, that investigate the effect of changes in spanwise phase on the control method effectiveness.

The rapid growth of the amplitude of the control-streaks due to the interaction with the triadic (difference) interactions. p. 3
Where the paper says it

For the same case study [18], when the control-streaks amplitude is increased to 𝐴𝑠𝑢 = 0. 2 ˜𝑢∞, the stable oblique, first Mack mode waves grow in amplitude and lead via triadic interaction [25] to streak instability that may dominate the transition process.

The control streaks not being sufficient to achieve an effective stabilization of the latter. p. 2
Where the paper says it

This can be passively attained through the use of alternate stripes of materials with different thermal properties, and by exploiting the high heat flux characteristics of the hypersonic regime. Effective stabilization of the second Mack mode through the novel control method can be attained using streaks with a wavelength that is approximately 8-10 times the local boundary layer thickness [22].

The effect of the control method is unaffected by mistuning between control and disturbance forcing. p. 9
Where the paper says it

The wall temperature boundary condition is 𝑇𝑤 = 𝑇𝑤,𝑏𝑎𝑠𝑒 1 + 𝐴𝑇𝑤 sin (𝑘𝑠𝑧 + 𝜃) , (11) where 𝐴𝑇𝑤 sets the amplitude of the wall temperature variation relative to the baseline (uniform) wall temperature, 𝑘𝑠 = 2𝜋/𝜆𝑧,𝑠 sets the fundamental spanwise wavenumber of the control streaks, and 𝜃 ∈ [0, 2𝜋] is used to control the relative phase between the wall temperature and the disturbance forcing boundary conditions. The parameter 𝜃 is set to zero for most of the investigations, but for the studies presented in appendix C, that investigate the effect of changes in spanwise phase on the control method effectiveness.

The helicity density (h) is integrated across the cross-section of the domain, and the quantity, H, is defined as. For a left-right symmetric flow H = 0. p. 1

Where the paper says it

Boundary layer instability and transition can significantly affect the flight envelope and operability limits of hypersonic vehicles [1]. For laminar hypersonic boundary layers, an important non dimensional parameter is the relative Mach number 𝑀, which is defined based on the velocity of the flow (𝑢) relative to the phase speed (𝑐𝑝ℎ) of the hydrodynamic instability within the boundary layer.

For both the uncontrolled and controlled configurations, the flow is asymmetric close to the start of the domain (x < 250, Fig. p. 9
Where the paper says it

4) are used. To achieve statistical convergence, the computations for the uncontrolled configurations are advanced in time for approximately 1.

28a), due to the function g(z) (equation (10)) which breaks the symmetry of the forcing disturbance. p. 8
Where the paper says it

The subscript (·)𝑤 denotes quantities evaluated at the wall. The function 𝑔(𝑧) in equation (10) introduces spanwise asymmetry and promotes faster transition to turbulence [34].

Then both the configurations recover the symmetry until x ≈ 750, when the uncontrolled case has H < 0 and the left-right symmetry is broken from there on as depicted from the cross-sectional distribution of the mass flow deficit in Fig. 28b. For the controlled configuration, fluctuations of H become significant from x ≈ 950. p. 1
Where the paper says it

Abstract Direct Numerical Simulation (DNS) of a Mach 6 boundary layer over a flat plate is performed to assess the effect of spanwise non-uniform surface temperature on breakdown to turbulence under deterministic forcing. The streamwise location of laminar to turbulent transition in hypersonic boundary layers has a significant influence on viscous drag and aerodynamic heating of external surfaces of hypersonic vehicles.

The grid resolution is quantified relative to the Kolmogorov length scale (eq. 20) through Δxeta, Δyeta, Δzeta, (A1). The initial peak in figure 23 corresponds to the disturbance forcing region (x ∈ [15, 20]). The maximum local Knudsen number based on the Kolmogorov length scale is approximately Kneta = λ/e ≈ 0.29, occurring only within a narrow region adjacent to the wall. The global Knudsen number remains Kn ≈ 2.03×10−3.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Enhanced Hypersonic Flow Control Modeling: The improved AI system can simulate and predict boundary layer transition delay by incorporating spanwise non-uniform surface temperature distributions to generate control streaks, specifically targeting stabilization of the second Mack mode fundamental resonance scenario.

  2. Predictive Aerothermodynamic Load Assessment: The system can accurately predict the reduction in peak wall heat flux for first and second Mack mode dominated breakdowns, quantifying reductions of approximately 15% and 34% respectively under controlled conditions.

  3. Transition Delay Quantification: The AI can estimate the delay in laminar to turbulent transition, showing that weak control streaks (amplitude below 5% of freestream velocity) can delay transition by approximately 40 to 60 times the local boundary layer thickness for the second Mack mode scenario.

  4. Heat Transfer Overshoot Mitigation: The system can predict how control-streaks affect heat transfer overshoot; specifically, for first Mack mode oblique breakdown, control streaks with a spanwise temperature variation of 0.25 and wavenumber of 8 reduce the overshoot down to 1.4 times the Reynolds analogy prediction.

  5. Flow Symmetry Preservation Analysis: The improved system can assess how control streaks preserve flow symmetry; it can demonstrate that for weak control streaks under second Mack mode fundamental resonance, transition delay is largely insensitive to the relative spanwise phase between the control law and forcing disturbance.

Abstract

Direct Numerical Simulation (DNS) of a Mach 6 boundary layer over a flat plate is performed to assess the effect of spanwise non-uniform surface temperature on breakdown to turbulence under deterministic forcing. The streamwise location of laminar to turbulent transition in hypersonic boundary layers has a significant influence on viscous drag and aerodynamic heating of external surfaces of hypersonic vehicles. Previous work investigated the stabilization of hypersonic boundary layers by optimally growing streaks. More recently, DNS for a hypersonic boundary layer showed that it is possible to generate streaks through a spanwise non-uniform surface temperature distribution. The laminar computations showed the control method can stabilize the second Mack mode and it is robust across a range of Mach numbers and wall temperature ratios. In this work, two scenarios are investigated where two-dimensional (second Mack mode) and oblique (first Mack mode) disturbances dominate the initial linear stage of transition. It is found that weak control streaks with amplitude below 5% of the freestream velocity can reduce high-frequency shear-stress due to the second Mack mode by approximately 30% relative to the uncontrolled configuration, and delay transition. For first Mack mode dominated breakdown, the control streaks have no effect on transition location, but the peak amplitude of the spanwise-integrated wall heat flux is reduced. For the first and second Mack mode-dominated scenarios, the mean and high-frequency peak heat transfer are reduced approximately by 15% and 34%, respectively. The dominant mechanisms are identified and attributed to the pressure work contribution to turbulent kinetic energy and the second Mack mode dilatation work.

Related papers