Booster-based beam recycling for swap-out injection at the High Energy Photon Source

summary

The gist

Fourth-generation synchrotron light sources require efficient injector architectures capable of producing high-charge replacement bunches through a booster-based beam recycling scheme at the High…

In short

The study designed a booster-based beam recycling scheme for high-charge swap-out injection at HEPS. This method uses the full-energy booster to both inject new low-energy bunches and accumulate extracted storage ring bunches, avoiding dedicated accumulator rings. Results show feasibility, with transmission efficiencies around 99%, establishing a practical route for future light sources.

Key concepts

Booster-based beam recycling
This scheme uses the full-energy booster as both an injector and a high-energy accumulator. It extracts a bunch from the storage ring, merges it with a low-charge bunch, accelerates them to full energy in the booster, and then reinjects them back into the storage ring. This reuses extracted particles instead of discarding them.
Same-bucket condition
This is a synchronization requirement where a bunch extracted from one storage ring bucket must return to that exact same bucket after passing through the booster. The design uses specific path-length conditions and timing parameters, like setting the booster dwell time to 16 ms, to ensure this precise return happens correctly.
High-charge swap-out injection
This is a technique used in light sources where stored bunches are replaced by high-charge replacement bunches directly. It requires an efficient injector capable of producing these high charges, which the booster recycling scheme helps achieve without needing a separate accumulator ring.

Terminology used across episodes

This episode discusses

The paper

Booster-based beam recycling for swap-out injection at the High Energy Photon Source · Read on arXiv

Institute of High Energy Physics, Chinese Academy of Sciences · University of Chinese Academy of Sciences

DOI: 10.1016/j.accel.2026.100001

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: I'm Kai.

Mira: And I'm Mira, here with Lev.

Kai: We're looking at the paper: "Booster-based beam recycling for swap-out injection at the High Energy Photon Source".

Mira: Here's the gist of the paper. Fourth-generation synchrotron light sources require efficient injector architectures capable of producing high-charge replacement bunches through a booster-based beam recycling scheme at the High Energy Photon Source The measured results characterize the recycling operation and quantify the transmission efficiency and performance limitations of the complete recycling loop Scheme Overview The booster-based beam-recycling swap-out injection scheme involves using the full-energy booster as both an injector and a high-energy accumulator An extracted storage-ring bunch is returned to the booster, merged with a low-charge bunch previously injected from the linac and accelerated to full energy Following high-energy damping, the merged bunch is reinjected into the original storage-ring bucket.

Kai: This approach avoids the need for a dedicated accumulator ring while enabling high-charge bunch replacement.

Mira: Synchronization and Timing Design The synchronization design is implemented through the HEPS timing system and injection-timing framework The same-bucket condition requires the recycled bunch to return to the original storage-ring RF bucket, formulated as a path-length synchronization condition.

Kai: The design choice N = 10575 corresponds to a booster dwell time of about 16 ms, which is the first synchronization-compatible solution that provides the required damping time discussed in Section 4.2.

Paper summary: Kai: So, moving into what they actually claim in this paper, they present a full recycling-chain simulation, commissioning studies, and measured performance analysis. They’re showing how this booster-based beam-recycling architecture works in practice for both high brightness and high charge modes.

Mira: The results show that the mean overall transmission efficiency was ninety-nine point nine nine percent for the high brightness mode, but it dropped to ninety-eight point nine seven percent for the high charge mode. They also pinpoint where those losses are happening.

Lev: The paper says the dominant loss mechanism happens during booster high-energy injection and that subsequent capture process, specifically when particles near the edge of the longitudinal phase space distribution exceed the booster's longitudinal acceptance.

Kai: And they also noted that charge-dependent efficiency reduction seems to appear in the direction from the booster back to the storage ring. So it’s not just one simple loss mechanism across the whole system.

Mira: They found that after BTR transport, during capture after reinjection into the storage ring is where most of the measured loss occurs, rather than during booster extraction or transmission through that BTR line itself.

Lev: That points to a specific region, a localized aperture restriction in the R18 region might have contributed to the efficiency degradation they saw in that transport line.

Kai: So they’re trying to figure out if it’s just an aperture issue or something deeper with how the bunch is captured back into the storage ring after it comes back from the booster.

Conclusion: Mira: To wrap up this paper, they establish that this booster-based beam recycling is a feasible route toward high-charge swap-out injection for future fourth-generation synchrotron light sources.

Kai: They’ve shown its operational basis for achieving high charge replacement in those next generation machines. The key finding is that the dominant measured loss occurs after BTR transport, during capture after reinjection into the storage ring, rather than during booster extraction or transmission through the BTR line itself.

Lev: So they’re confirming that their method works and pointing them toward where they need to focus their next optimization efforts. The remaining optimization of high charge storage ring capture after reinjection will determine the achievable bunch charge and operational margin.

Mira: It establishes the feasibility of this architecture, but it also tells us exactly what needs fixing next—that localized aperture restriction in the R18 region might have played a role in that BTR efficiency degradation.

Kai: The whole point is that they’ve proven this recycling method is a practical way forward for getting those high-charge bunches into those demanding machines.

Lev: It’s about proving the concept works, but now it's about tuning the final pieces to get the best performance and operational margin they need for real hardware.

More episodes

← Home