Analysis and simulations of droplet generation regimes in a coaxial microfluidic device

summary

The gist

The generation of microdroplets via segmentation in microfluidic devices is of interest in many applications, from biochemical to pharmaceutical <ref:2601.09483#pg6>.

In short

This work evaluates open-source Basilisk software to predict microdroplet generation in coaxial microfluidic devices. It validates the tool against experimental data and proposes new scaling laws for droplet diameters across dripping and jetting regimes, incorporating viscosity ratios for more accurate predictions.

Key concepts

Basilisk
Basilisk is an open-source library of solvers used to model various fluid dynamics problems. In this study, it was tested to see if it accurately predicts how microdroplets form when fluids interact in a microfluidic device.
Dripping and Jetting Regimes
These are two distinct flow regimes during droplet generation. Dripping involves slow, discrete release of droplets from the junction, while jetting involves a continuous stream of fluid exiting the device. The paper maps these regimes based on physical parameters like Capillary number.
Capillary Number (Ca)
The Capillary number is a dimensionless group that relates viscous forces to surface tension forces in fluid flow. It is used to categorize the flow behavior, helping researchers determine whether a system operates in the dripping or jetting regime for droplet formation.

Terminology used across episodes

This episode discusses

The paper

Analysis and simulations of droplet generation regimes in a coaxial microfluidic device · Read on arXiv

Alessio Innocenti, Andrea Poggi, Simone Camarri, Maria Vittoria Salvetti

University of Pisa

The generation of microdroplets via segmentation in microfluidic devices is of interest in many applications, from biochemical to pharmaceutical. This technique permits indeed much higher control on the droplet size, uniformity and generation rate than in standard batch generation processes. In this work we have evaluated the suitability of the open-source software Basilisk to accurately predict microdroplet generation by segmentation. We have validated the numerical tool with analytical solutions for the dynamics of droplets in confined flows, namely with Bretherton theory, and by comparison with literature experimental results. We have then performed several campaigns of numerical simulations for a coaxial device, analyzing the different regimes of droplet generation, and evaluating how the physical and flow parameters affect the production mechanisms and the diameters of the generated droplets. Finally we have proposed new scaling laws for the prediction of droplet diameters in the dripping and jetting regimes, refining existing ones by taking into account additional physical effects, like the viscosity ratio.

DOI: 10.1016/j.compfluid.2026.107334

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: We're looking at the paper: "Analysis and simulations of droplet generation regimes in a coaxial microfluidic device".

Mira: Here's the gist of the paper. The generation of microdroplets via segmentation in microfluidic devices is of interest in many applications, from biochemical to pharmaceutical <ref:2601.09483#pg6>.

Kai: This work evaluates the suitability of the open-source software Basilisk to accurately predict microdroplet generation by segmentation <ref:2601.09483#pg6> and proposes new scaling laws for the prediction of droplet diameters in the dripping and jetting regimes <ref:2601.09483#pg6>.

Mira: Modeling Fluid Dynamics The dynamics of droplet generation in a microfluidic device are described where two non-miscible fluids enter from separate channels, come in contact at a junction, and flow out from the same channel <ref:2601.09483#pg8> The physical parameters characterizing the problem are the viscosities and densities of the two fluids, µi and ρi, and surface tension σ <ref:2601.09483#pg8> Based on these physical, geometrical and flow parameters, four dimensionless groups can be formed <ref:2601.09483#pg8> These groups include the viscosity and density ratios, respectively µd/µc and ρd/ρc <ref:2601.09483#pg8>, as well as the Reynolds and Capillary number <ref:2601.09483#pg8>.

Kai: Numerical Implementation of Basilisk Basilisk is a library of solvers that can be used for a variety of fluid dynamics applications, from industrial to geophysical flows <ref:2601.09483#pg9> All the different parts share a common discretization based on the finite volume method on Cartesian grid <ref:2601.09483#pg9>.

Title and authors: Kai: So we’re talking about "Analysis and simulations of droplet generation regimes in a coaxial microfluidic device." The authors are Alessio Innocenti, Andrea Poggi, Simone Camarri, and Maria Vittoria Salvetti from the University of Pisa. It sounds like they’ve put a lot of effort into simulating these systems using Basilisk.

Mira: They aren't just running one simulation; they’re systematically analyzing how the production mechanisms change depending on the physical and flow parameters in a coaxial setup. That suggests they are trying to map out the entire landscape of droplet formation, from one condition to another.

Lev: What I find interesting is that they are testing Basilisk against analytical solutions from Bretherton theory and literature experimental results. For me, it means they aren't just making up numbers; they’re grounding their numerical predictions in established theoretical frameworks and what we already know from the lab.

Kai: Exactly. They’re using this comparison to see how well Basilisk predicts droplet generation by segmentation, which is a specific technique they are interested in because it gives better control over size and uniformity than older batch methods do.

Mira: And when you look at the regimes they're studying, they’re focusing on how the balance between surface tension, viscous stresses from the outer fluid, and inertial forces from the inner fluid dictates whether you get dripping or jetting.

Lev: The paper also mentions that they are performing several campaigns of numerical simulations for a coaxial device to analyze these different regimes. That suggests they aren't just looking at one perfect setup; they’re testing how the system behaves under varying conditions.

Kai: So, in short, this paper is about using a specific computer tool to explore the physics of droplet making in coaxial microchannels and checking if the results match what theory and experiments suggest. It sets up a good foundation for understanding these systems.

Mira: And it’s important because they are looking at how things like the viscosity ratio play into this, which is something that often gets overlooked when you just look at simple flow setups. That’s a big piece of the puzzle here for understanding droplet behavior.

Lev: It gives us a way to see what these simulations would actually need to run on real hardware later, by testing the software’s accuracy against known physics first.

The paper's summary: Kai: To summarize, this paper dives into the dynamics of droplet generation in a coaxial microfluidic device where two non-miscible fluids meet and flow out. They are using segmentation to generate these droplets and they’re evaluating Basilisk software for its accuracy in predicting this whole process.

Mira: The summary highlights that the geometrical configurations can be quite varied, ranging from cross-flow and T-junction setups to co-flow and flow focusing setups, which shows the breadth of what they are studying.

Lev: It’s clear they are looking at how surface tension provides a stabilizing effect while viscous stresses and inertial forces destabilize the system on different sides of the junction. That’s a classic fluid dynamics problem in microchannels that requires careful balancing.

Kai: And they quantify this balance using dimensionless numbers, specifically the Capillary number and the Weber number, to characterize these different regimes of formation and breakup.

Mira: The summary points out that at very low capillary numbers, surface tension dominates, leading to the jet tip growing until it blocks the junction before breaking off. But at larger capillary numbers, you get a steady dripping regime or a convective instability leading to a jetting regime.

Lev: So they are essentially defining the transition points between these two distinct modes—dripping and jetting—based on how those dimensionless numbers behave as you change the flow conditions.

Kai: What this means for us is that we have a clearer picture of what drives the breakup instability, which helps us understand how to design channels to get a specific droplet size or generation rate.

Mira: It also sets up the next step: they propose new scaling laws for predicting droplet diameters in both the dripping and jetting regimes, moving beyond just describing the mechanisms.

Lev: That’s a big leap because those scaling laws are what you actually use to predict things in a design phase, not just theoretical descriptions of how it happens.

The paper's improvements: Kai: The authors suggest some specific improvements to their work, and one of the most important is taking additional physical effects into account, specifically the viscosity ratio. They feel that incorporating this parameter will refine the existing scaling laws significantly.

Mira: I agree with that. When you’re modeling flows where you have two fluids with different viscosities, ignoring that ratio can lead to big errors in predicting things like droplet diameters and pinch-off positions.

Lev: From an engineering standpoint, if they incorporate the viscosity ratio properly into the scaling laws, it makes the model much more useful for real hardware design because it accounts for a real physical difference between the fluids.

Kai: They derive a specific scaling law for the dripping regime: ddrop over D equals zero point two three three times Ca to the negative zero point three three times c to the positive zero point two times d multiplied by mu sub d over mu sub c raised to the negative zero point two two and Re to the negative zero point zero zero zero.

Mira: That formula shows how droplet diameter relates directly to all those parameters, including that viscosity ratio term they mentioned earlier, which is a nice refinement of what was previously there.

Lev: And for the jetting regime, they give a scaling law as well: ddrop over D equals two point four eight multiplied by the ratio of flow rates divided by the sum of flow rates over two times that ratio to the power zero and mu sub d over mu sub c raised to zero and zero point one two four.

Kai: So they’ve essentially taken empirical relations and refined them by adding these new physical dependencies, which is exactly what you need when you want accurate predictions for a device.

Mira: The improvement here is moving from just describing the regimes to actually providing predictive equations for the droplet diameters in those regimes, which is a much more practical thing to have.

Conclusion: Kai: So, wrapping up on this paper, what we’ve seen is that they’ve used Basilisk to test droplet generation by segmentation in coaxial microfluidics and found it works well against theory and experiments. They are also proposing new scaling laws for the dripping and jetting regimes that include things like the viscosity ratio.

Mira: The big implication is that we now have better tools for predicting droplet sizes in these complex flows, not just a general description of how they form, but specific equations for different flow types.

Lev: From my perspective on running this on real hardware, it means the simulations are getting more physically grounded when we talk about scaling them up or trying to translate them into something you can build.

Kai: It’s definitely a step forward in using these simulation tools to guide the design of microfluidic devices for things like drug delivery, where precise control over droplet size is so important.

Mira: The authors acknowledge that their study focuses on the effects of varying the Capillary number and Weber number, and they point out that fully three-dimensional simulations are still a bit ahead in development right now.

Lev: So they admit the limitation is that while they’ve mapped out many regimes, getting those truly full three-dimensional simulations done is still a bit of a work in progress for the software.

Kai: Exactly. It shows where we are now, and what’s next—that continued improvement of solvers will let them push into those fully three-dimensional scenarios soon.

Mira: So, to finish up on "Analysis and simulations of droplet generation regimes in a coaxial microfluidic device," we've seen a solid validation of the tools and some new predictive scaling laws that incorporate viscosity ratios for both dripping and jetting regimes.

Lev: It gives us a clearer path for how these numerical models can be applied to actual device design, by accounting for those real physical differences between the fluids.

More episodes

← Home