Analysis and simulations of droplet generation regimes in a coaxial microfluidic device

arXiv:2601.09483 · physics.flu-dyn · Submitted 2026-01-14 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: We're looking at the paper: "Analysis and simulations of droplet generation regimes in a coaxial microfluidic device".

Mira: Here's the gist of the paper. The generation of microdroplets via segmentation in microfluidic devices is of interest in many applications, from biochemical to pharmaceutical <ref:2601.09483#pg6>.

Kai: This work evaluates the suitability of the open-source software Basilisk to accurately predict microdroplet generation by segmentation <ref:2601.09483#pg6> and proposes new scaling laws for the prediction of droplet diameters in the dripping and jetting regimes <ref:2601.09483#pg6>.

Mira: Modeling Fluid Dynamics The dynamics of droplet generation in a microfluidic device are described where two non-miscible fluids enter from separate channels, come in contact at a junction, and flow out from the same channel <ref:2601.09483#pg8> The physical parameters characterizing the problem are the viscosities and densities of the two fluids, µi and ρi, and surface tension σ <ref:2601.09483#pg8> Based on these physical, geometrical and flow parameters, four dimensionless groups can be formed <ref:2601.09483#pg8> These groups include the viscosity and density ratios, respectively µd/µc and ρd/ρc <ref:2601.09483#pg8>, as well as the Reynolds and Capillary number <ref:2601.09483#pg8>.

Kai: Numerical Implementation of Basilisk Basilisk is a library of solvers that can be used for a variety of fluid dynamics applications, from industrial to geophysical flows <ref:2601.09483#pg9> All the different parts share a common discretization based on the finite volume method on Cartesian grid <ref:2601.09483#pg9>.

Title and authors: Kai: So we’re talking about "Analysis and simulations of droplet generation regimes in a coaxial microfluidic device." The authors are Alessio Innocenti, Andrea Poggi, Simone Camarri, and Maria Vittoria Salvetti from the University of Pisa. It sounds like they’ve put a lot of effort into simulating these systems using Basilisk.

Mira: They aren't just running one simulation; they’re systematically analyzing how the production mechanisms change depending on the physical and flow parameters in a coaxial setup. That suggests they are trying to map out the entire landscape of droplet formation, from one condition to another.

Lev: What I find interesting is that they are testing Basilisk against analytical solutions from Bretherton theory and literature experimental results. For me, it means they aren't just making up numbers; they’re grounding their numerical predictions in established theoretical frameworks and what we already know from the lab.

Kai: Exactly. They’re using this comparison to see how well Basilisk predicts droplet generation by segmentation, which is a specific technique they are interested in because it gives better control over size and uniformity than older batch methods do.

Mira: And when you look at the regimes they're studying, they’re focusing on how the balance between surface tension, viscous stresses from the outer fluid, and inertial forces from the inner fluid dictates whether you get dripping or jetting.

Lev: The paper also mentions that they are performing several campaigns of numerical simulations for a coaxial device to analyze these different regimes. That suggests they aren't just looking at one perfect setup; they’re testing how the system behaves under varying conditions.

Kai: So, in short, this paper is about using a specific computer tool to explore the physics of droplet making in coaxial microchannels and checking if the results match what theory and experiments suggest. It sets up a good foundation for understanding these systems.

Mira: And it’s important because they are looking at how things like the viscosity ratio play into this, which is something that often gets overlooked when you just look at simple flow setups. That’s a big piece of the puzzle here for understanding droplet behavior.

Lev: It gives us a way to see what these simulations would actually need to run on real hardware later, by testing the software’s accuracy against known physics first.

The paper's summary: Kai: To summarize, this paper dives into the dynamics of droplet generation in a coaxial microfluidic device where two non-miscible fluids meet and flow out. They are using segmentation to generate these droplets and they’re evaluating Basilisk software for its accuracy in predicting this whole process.

Mira: The summary highlights that the geometrical configurations can be quite varied, ranging from cross-flow and T-junction setups to co-flow and flow focusing setups, which shows the breadth of what they are studying.

Lev: It’s clear they are looking at how surface tension provides a stabilizing effect while viscous stresses and inertial forces destabilize the system on different sides of the junction. That’s a classic fluid dynamics problem in microchannels that requires careful balancing.

Kai: And they quantify this balance using dimensionless numbers, specifically the Capillary number and the Weber number, to characterize these different regimes of formation and breakup.

Mira: The summary points out that at very low capillary numbers, surface tension dominates, leading to the jet tip growing until it blocks the junction before breaking off. But at larger capillary numbers, you get a steady dripping regime or a convective instability leading to a jetting regime.

Lev: So they are essentially defining the transition points between these two distinct modes—dripping and jetting—based on how those dimensionless numbers behave as you change the flow conditions.

Kai: What this means for us is that we have a clearer picture of what drives the breakup instability, which helps us understand how to design channels to get a specific droplet size or generation rate.

Mira: It also sets up the next step: they propose new scaling laws for predicting droplet diameters in both the dripping and jetting regimes, moving beyond just describing the mechanisms.

Lev: That’s a big leap because those scaling laws are what you actually use to predict things in a design phase, not just theoretical descriptions of how it happens.

The paper's improvements: Kai: The authors suggest some specific improvements to their work, and one of the most important is taking additional physical effects into account, specifically the viscosity ratio. They feel that incorporating this parameter will refine the existing scaling laws significantly.

Mira: I agree with that. When you’re modeling flows where you have two fluids with different viscosities, ignoring that ratio can lead to big errors in predicting things like droplet diameters and pinch-off positions.

Lev: From an engineering standpoint, if they incorporate the viscosity ratio properly into the scaling laws, it makes the model much more useful for real hardware design because it accounts for a real physical difference between the fluids.

Kai: They derive a specific scaling law for the dripping regime: ddrop over D equals zero point two three three times Ca to the negative zero point three three times c to the positive zero point two times d multiplied by mu sub d over mu sub c raised to the negative zero point two two and Re to the negative zero point zero zero zero.

Mira: That formula shows how droplet diameter relates directly to all those parameters, including that viscosity ratio term they mentioned earlier, which is a nice refinement of what was previously there.

Lev: And for the jetting regime, they give a scaling law as well: ddrop over D equals two point four eight multiplied by the ratio of flow rates divided by the sum of flow rates over two times that ratio to the power zero and mu sub d over mu sub c raised to zero and zero point one two four.

Kai: So they’ve essentially taken empirical relations and refined them by adding these new physical dependencies, which is exactly what you need when you want accurate predictions for a device.

Mira: The improvement here is moving from just describing the regimes to actually providing predictive equations for the droplet diameters in those regimes, which is a much more practical thing to have.

Conclusion: Kai: So, wrapping up on this paper, what we’ve seen is that they’ve used Basilisk to test droplet generation by segmentation in coaxial microfluidics and found it works well against theory and experiments. They are also proposing new scaling laws for the dripping and jetting regimes that include things like the viscosity ratio.

Mira: The big implication is that we now have better tools for predicting droplet sizes in these complex flows, not just a general description of how they form, but specific equations for different flow types.

Lev: From my perspective on running this on real hardware, it means the simulations are getting more physically grounded when we talk about scaling them up or trying to translate them into something you can build.

Kai: It’s definitely a step forward in using these simulation tools to guide the design of microfluidic devices for things like drug delivery, where precise control over droplet size is so important.

Mira: The authors acknowledge that their study focuses on the effects of varying the Capillary number and Weber number, and they point out that fully three-dimensional simulations are still a bit ahead in development right now.

Lev: So they admit the limitation is that while they’ve mapped out many regimes, getting those truly full three-dimensional simulations done is still a bit of a work in progress for the software.

Kai: Exactly. It shows where we are now, and what’s next—that continued improvement of solvers will let them push into those fully three-dimensional scenarios soon.

Mira: So, to finish up on "Analysis and simulations of droplet generation regimes in a coaxial microfluidic device," we've seen a solid validation of the tools and some new predictive scaling laws that incorporate viscosity ratios for both dripping and jetting regimes.

Lev: It gives us a clearer path for how these numerical models can be applied to actual device design, by accounting for those real physical differences between the fluids.

Alessio Innocenti, Andrea Poggi, Simone Camarri, Maria Vittoria Salvetti

University of Pisa

physics.flu-dyn

Submitted: 2026-01-14

Updated: 2026-11-04

Comments: 35 pages. Accepted version

DOI: 10.1016/j.compfluid.2026.107334

License: http://creativecommons.org/licenses/by-nc-nd/4.0/

Importance score: 80/100

The gist: The generation of microdroplets via segmentation in microfluidic devices is of interest in many applications, from biochemical to pharmaceutical <ref:2601.09483#pg6>.

Key concepts

Basilisk
Basilisk is an open-source library of solvers used to model various fluid dynamics problems. In this study, it was tested to see if it accurately predicts how microdroplets form when fluids interact in a microfluidic device.
Dripping and Jetting Regimes
These are two distinct flow regimes during droplet generation. Dripping involves slow, discrete release of droplets from the junction, while jetting involves a continuous stream of fluid exiting the device. The paper maps these regimes based on physical parameters like Capillary number.
Capillary Number (Ca)
The Capillary number is a dimensionless group that relates viscous forces to surface tension forces in fluid flow. It is used to categorize the flow behavior, helping researchers determine whether a system operates in the dripping or jetting regime for droplet formation.

Terminology

Summary

The generation of microdroplets via segmentation in microfluidic devices is of interest in many applications, from biochemical to pharmaceutical <ref:2601. p. 0

Where the paper says it

Analysis and simulations of droplet generation regimes in a coaxial microfluidic device Alessio Innocenti∗ , Andrea Poggi, Simone Camarri, Maria Vittoria Salvetti University of Pisa, Dipartimento di Ingegneria Civile e Industriale, Largo Lucio Lazzarino, 56122, Pisa, Italy Abstract The generation of microdroplets via segmentation in microfluidic devices is of interest in many applications, from biochemical to pharmaceutical. This technique permits indeed much higher control on the droplet size, uniformity and generation rate than in standard batch generation processes.

09483#pg6>. This work evaluates the suitability of the open-source software Basilisk to accurately predict microdroplet generation by segmentation <ref:2601. p. 0
Where the paper says it

This technique permits indeed much higher control on the droplet size, uniformity and generation rate than in standard batch generation processes. In this work we have evaluated the suitability of the open-source software Basilisk to accurately predict microdroplet generation by segmentation.

09483#pg6> and proposes new scaling laws for the prediction of droplet diameters in the dripping and jetting regimes <ref:2601. p. 0
Where the paper says it

We have then performed several campaigns of numerical simulations for a coaxial device, analyzing the different regimes of droplet generation, and evaluating how the physical and flow parameters affect the production mechanisms and the diameters of the generated droplets. Finally we have proposed new scaling laws for the prediction of droplet diameters in the dripping and jetting regimes, refining existing ones by taking ∗Corresponding author Email address: alessio.

09483#pg6>.

Modeling Fluid Dynamics

The dynamics of droplet generation in a microfluidic device are described where two non-miscible fluids enter from separate channels, come in contact at a junction, and flow out from the same channel <ref:2601.09483#pg8> The physical parameters characterizing the problem are the viscosities and densities of the two fluids, µi and ρi, and surface tension σ <ref:2601. p. 5

Where the paper says it

Modeling and governing equations We describe the dynamics of droplet generation in a microfluidic device, where two non-miscible fluids enter from separate channels, come in contact at a junction, and flow out from the same channel. The physical parameters characterizing the problem are the viscosities and densities of the two fluids, µi and ρi , and surface tension σ.

09483#pg8> Based on these physical, geometrical and flow parameters, four dimensionless groups can be formed <ref:2601. p. 5
Where the paper says it

), the additional parameters characterizing the flow are the inlet velocities of the two fluids, Uc and Ud, and a characteristic dimension of the channels, typically the diameter, D, in coaxial configurations or the channel height, H, in square section channels. Based on these physical, geometrical and flow parameters, four dimensionless groups can be formed: firstly the viscosity and density ratios, respectively µd/µc and ρd/ρc; secondly the Reynolds and Capillary number, that for these kind of flows can be defined based on the continuous phase properties as follows Rec = ρcUcD µc , Cac = µcUc σ (1) An alternative, quite common in microfluidics literature, is to replace one of these two dimensionless number with the Weber number, defined as follows: W ec = ρcU 2 c D σ = Rec · Cac (2) The two fluids are governed by the Navier-Stokes incompressible equations with variable density and viscosity, which in their dimensionless form 6

09483#pg8> These groups include the viscosity and density ratios, respectively µd/µc and ρd/ρc <ref:2601. p. 5
Where the paper says it

), the additional parameters characterizing the flow are the inlet velocities of the two fluids, Uc and Ud, and a characteristic dimension of the channels, typically the diameter, D, in coaxial configurations or the channel height, H, in square section channels. Based on these physical, geometrical and flow parameters, four dimensionless groups can be formed: firstly the viscosity and density ratios, respectively µd/µc and ρd/ρc; secondly the Reynolds and Capillary number, that for these kind of flows can be defined based on the continuous phase properties as follows Rec = ρcUcD µc , Cac = µcUc σ (1) An alternative, quite common in microfluidics literature, is to replace one of these two dimensionless number with the Weber number, defined as follows: W ec = ρcU 2 c D σ = Rec · Cac (2) The two fluids are governed by the Navier-Stokes incompressible equations with variable density and viscosity, which in their dimensionless form 6

09483#pg8>, as well as the Reynolds and Capillary number <ref:2601. p. 5
Where the paper says it

), the additional parameters characterizing the flow are the inlet velocities of the two fluids, Uc and Ud, and a characteristic dimension of the channels, typically the diameter, D, in coaxial configurations or the channel height, H, in square section channels. Based on these physical, geometrical and flow parameters, four dimensionless groups can be formed: firstly the viscosity and density ratios, respectively µd/µc and ρd/ρc; secondly the Reynolds and Capillary number, that for these kind of flows can be defined based on the continuous phase properties as follows Rec = ρcUcD µc , Cac = µcUc σ (1) An alternative, quite common in microfluidics literature, is to replace one of these two dimensionless number with the Weber number, defined as follows: W ec = ρcU 2 c D σ = Rec · Cac (2) The two fluids are governed by the Navier-Stokes incompressible equations with variable density and viscosity, which in their dimensionless form 6

09483#pg8>.

Numerical Implementation of Basilisk

Basilisk is a library of solvers that can be used for a variety of fluid dynamics applications, from industrial to geophysical flows <ref:2601.09483#pg9> All the different parts share a common discretization based on the finite volume method on Cartesian grid <ref:2601. p. 7

Where the paper says it

build a specific solver assembly with the desired features. All the different parts share a common discretization based on the finite volume method on Cartesian grid.

09483#pg9>. The interface is advected with a geometric piecewise-linear interface construction (PLIC) VOF method <ref:2601. p. 7
Where the paper says it

All simulations performed with Basilisk have been done with adaptive mesh refinement (AMR) on quadtree grids. The interface is advected with a geometric piecewise-linear interface construction (PLIC) VOF method ([21, 22]), generalized for the quad/octree spatial discretization, which can ensure a sharp interface while preserving mass conservation.

09483#pg9> which can ensure a sharp interface while preserving mass conservation <ref:2601. p. 7
Where the paper says it

All simulations performed with Basilisk have been done with adaptive mesh refinement (AMR) on quadtree grids. The interface is advected with a geometric piecewise-linear interface construction (PLIC) VOF method ([21, 22]), generalized for the quad/octree spatial discretization, which can ensure a sharp interface while preserving mass conservation.

09483#pg9>. The surface tension term in Equation (4) is modeled with the continuum surface force (CSF) approach <ref:2601. p. 8
Where the paper says it

sion successively, with a fractional step method that guarantees exact mass conservation. The surface tension term in Equation (4) is modeled with the continuum surface force (CSF) approach [24].

09483#pg10>.

Validation and Simulation Results

The work validates Basilisk by analyzing a 2-dimensional Taylor bubble configuration, finding excellent agreement with theoretical and empirical literature laws for droplet terminal velocity <ref:2601.09483#pg8> For the coaxial configuration, simulations correctly reproduce the generation mechanisms, and the diameter and pinch-off position are in agreement with experimental images <ref:2601. p. 0

Where the paper says it

We have validated the numerical tool with analytical solutions for the dynamics of droplets in confined flows, namely with Bretherton theory, and by comparison with literature experimental results. We have then performed several campaigns of numerical simulations for a coaxial device, analyzing the different regimes of droplet generation, and evaluating how the physical and flow parameters affect the production mechanisms and the diameters of the generated droplets.

09483#pg8>. The analysis of different regimes shows that increasing the continuous phase Capillary number results in a decrease of droplet diameters in the dripping regime <ref:2601. p. 3
Where the paper says it

Even if not always all these aspect are considered rigorously, the literature on numerical approaches to droplet generation in microdevices is rapidly increasing, and different methods and softwares are now commonly used in device design. [7] have simulated coflowing devices with a front-tracking method [8] to track the interface between the two immiscible phases, exploiting mainly the dripping and jetting regimes at different values of the Capillary and Weber numbers.

09483#pg8>.

Proposed Scaling Laws

New scaling laws are proposed to predict droplet diameters in the dripping and jetting regimes, refining existing ones by taking into account additional physical effects like the viscosity ratio <ref:2601.09483#pg8> The derived scaling law for the dripping regime is ddrop/D = 0. p. 4

Where the paper says it

New scaling laws are finally proposed to predict droplet diameters in the dripping and jetting regimes, improving existing ones by including additional effects such as the viscosity ratio. The work is structured as follows: in Section 2 we briefly describe the mathematical formulation of the problem; in Section 3 we report the details of the numerical implementation of Basilisk; in Section 4 we validate and assess the accuracy of Basilisk for a Taylor bubble configuration; in Section 5 we analyze in details a coaxial configuration for droplet generation with validation against literature experiments, regime mapping and derivation of scaling laws for the droplet diameter.

233 · Ca−0.33c · Ca0.2d · (µd/µc)−0. p. 5
Where the paper says it

), the additional parameters characterizing the flow are the inlet velocities of the two fluids, Uc and Ud, and a characteristic dimension of the channels, typically the diameter, D, in coaxial configurations or the channel height, H, in square section channels. Based on these physical, geometrical and flow parameters, four dimensionless groups can be formed: firstly the viscosity and density ratios, respectively µd/µc and ρd/ρc; secondly the Reynolds and Capillary number, that for these kind of flows can be defined based on the continuous phase properties as follows Rec = ρcUcD µc , Cac = µcUc σ (1) An alternative, quite common in microfluidics literature, is to replace one of these two dimensionless number with the Weber number, defined as follows: W ec = ρcU 2 c D σ = Rec · Cac (2) The two fluids are governed by the Navier-Stokes incompressible equations with variable density and viscosity, which in their dimensionless form 6

22 · Re−0.002d <ref:2601. p. 0
Where the paper says it

innocenti@unipi. it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601.

09483#pg8>. A scaling law for the jetting regime is given by ddrop/D = 2. p. 4
Where the paper says it

New scaling laws are finally proposed to predict droplet diameters in the dripping and jetting regimes, improving existing ones by including additional effects such as the viscosity ratio. The work is structured as follows: in Section 2 we briefly describe the mathematical formulation of the problem; in Section 3 we report the details of the numerical implementation of Basilisk; in Section 4 we validate and assess the accuracy of Basilisk for a Taylor bubble configuration; in Section 5 we analyze in details a coaxial configuration for droplet generation with validation against literature experiments, regime mapping and derivation of scaling laws for the droplet diameter.

48 · (Qd/(Qc + Qd)/2)0·(µd/µc)0·0. p. 5
Where the paper says it

), the additional parameters characterizing the flow are the inlet velocities of the two fluids, Uc and Ud, and a characteristic dimension of the channels, typically the diameter, D, in coaxial configurations or the channel height, H, in square section channels. Based on these physical, geometrical and flow parameters, four dimensionless groups can be formed: firstly the viscosity and density ratios, respectively µd/µc and ρd/ρc; secondly the Reynolds and Capillary number, that for these kind of flows can be defined based on the continuous phase properties as follows Rec = ρcUcD µc , Cac = µcUc σ (1) An alternative, quite common in microfluidics literature, is to replace one of these two dimensionless number with the Weber number, defined as follows: W ec = ρcU 2 c D σ = Rec · Cac (2) The two fluids are governed by the Navier-Stokes incompressible equations with variable density and viscosity, which in their dimensionless form 6

124 <ref:2601. p. 0
Where the paper says it

innocenti@unipi. it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601.

09483#pg8>.

Regime Mapping and Conclusion

The systematic parametric study identified different regimes of droplet generation in terms of Capillary number of the continuous phase and Weber number of the dispersed phase <ref:2601.09483#pg8>. The results support and complement literature results, providing valuable information for preliminary design of microfluidic coaxial devices <ref:2601. p. 0

Where the paper says it

We have validated the numerical tool with analytical solutions for the dynamics of droplets in confined flows, namely with Bretherton theory, and by comparison with literature experimental results. We have then performed several campaigns of numerical simulations for a coaxial device, analyzing the different regimes of droplet generation, and evaluating how the physical and flow parameters affect the production mechanisms and the diameters of the generated droplets.

09483#pg8>. This work paves the way for the use of Basilisk software in this type of microfluidic applications <ref:2601. p. 4
Where the paper says it

In this work we want to evaluate the suitability of the opensource software Basilisk (https://basilisk. fr) to tackle those kind of applications.

09483#pg8>. The authors emphasize the importance of taking the viscosity ratio into account in both regimes <ref:2601. p. 1
Where the paper says it

into account additional physical effects, like the viscosity ratio. Introduction The processes of droplet generation at the milli to micro scale has attracted considerable attention due to the numerous applications in which micro-droplets are involved, such as: (i) lab-on-a-chip devices (miniaturized reproductions of laboratory processes at the micro/milli scale) for sample preparation, mixing, separation and detection; (ii) drug delivery through microparticles, nanoparticles, coated microparticles and microencapsulation, which has the great advantage of delivering small doses of drug only in the desired site, reducing accumulation and undesired systemic effects, together with a better control on the release rate, by modifying the microenvironment [1]; (iii) encapsulation and manipulations of single cells in aqueous droplets for cell culture, which allows isolating each individual cell in its microenvironement [2].

09483#pg8>. The paper concludes by showing that fully 3-dimensional simulations will soon be possible thanks to the continuous development and improvement of existing functions and solvers <ref:2601.09483#pg8>.

Acknowledgments

This work is supported by PNRR M4C2 - HPC, Big data and Quantum Computing (Simulazioni, calcolo e analisi dei dati e altre prestazioni - CN1) - CUP I53C22000690001 SPOKE 6 Multiscale modeling & Engineering applications <ref:2601.09483#pg8>. We also acknowledge the CINECA award under the ISCRA initiative for the availability of high performance computing resources and support <ref:2601.09483#pg8>.

References

[1] Ava M Vargason, Aaron C Anselmo, and Samir Mitragotri. The evolution of commercial drug delivery technologies. p. 1

Where the paper says it

into account additional physical effects, like the viscosity ratio. Introduction The processes of droplet generation at the milli to micro scale has attracted considerable attention due to the numerous applications in which micro-droplets are involved, such as: (i) lab-on-a-chip devices (miniaturized reproductions of laboratory processes at the micro/milli scale) for sample preparation, mixing, separation and detection; (ii) drug delivery through microparticles, nanoparticles, coated microparticles and microencapsulation, which has the great advantage of delivering small doses of drug only in the desired site, reducing accumulation and undesired systemic effects, together with a better control on the release rate, by modifying the microenvironment [1]; (iii) encapsulation and manipulations of single cells in aqueous droplets for cell culture, which allows isolating each individual cell in its microenvironement [2].

Nature Biomedical Engineering, 5(9):951–967, 2021 <ref:2601. p. 0
Where the paper says it

innocenti@unipi. it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601.

p. 0
Where the paper says it

innocenti@unipi. it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601.

09483#pg8>

[2] Sarah Köster, Francesco E Angile, Honey Duan, Jeremy J Agresti, Anton Wintner, Christian Schmitz, Amy C Rowat, Christoph A Merten, Dario Pisignano, Andrew D Griffiths, et al. Drop-based microfluidic devices for encapsulation of single cells. p. 1

Where the paper says it

Introduction The processes of droplet generation at the milli to micro scale has attracted considerable attention due to the numerous applications in which micro-droplets are involved, such as: (i) lab-on-a-chip devices (miniaturized reproductions of laboratory processes at the micro/milli scale) for sample preparation, mixing, separation and detection; (ii) drug delivery through microparticles, nanoparticles, coated microparticles and microencapsulation, which has the great advantage of delivering small doses of drug only in the desired site, reducing accumulation and undesired systemic effects, together with a better control on the release rate, by modifying the microenvironment [1]; (iii) encapsulation and manipulations of single cells in aqueous droplets for cell culture, which allows isolating each individual cell in its microenvironement [2]. Droplet generation via segmentation in microfluidic devices has the great advantage with respect to batch methods of ensuring excellent control on size distribution, allowing the generation of almost monodisperse droplets, and on generation rates, at the cost of lower processed volumes.

Lab on a Chip, 8(7):1110–1115, 2008 <ref:2601. p. 1
Where the paper says it

into account additional physical effects, like the viscosity ratio. Introduction The processes of droplet generation at the milli to micro scale has attracted considerable attention due to the numerous applications in which micro-droplets are involved, such as: (i) lab-on-a-chip devices (miniaturized reproductions of laboratory processes at the micro/milli scale) for sample preparation, mixing, separation and detection; (ii) drug delivery through microparticles, nanoparticles, coated microparticles and microencapsulation, which has the great advantage of delivering small doses of drug only in the desired site, reducing accumulation and undesired systemic effects, together with a better control on the release rate, by modifying the microenvironment [1]; (iii) encapsulation and manipulations of single cells in aqueous droplets for cell culture, which allows isolating each individual cell in its microenvironement [2].

09483#pg8>

[3] Shelley Lynn Anna. Droplets and bubbles in microfluidic devices. p. 1

Where the paper says it

Introduction The processes of droplet generation at the milli to micro scale has attracted considerable attention due to the numerous applications in which micro-droplets are involved, such as: (i) lab-on-a-chip devices (miniaturized reproductions of laboratory processes at the micro/milli scale) for sample preparation, mixing, separation and detection; (ii) drug delivery through microparticles, nanoparticles, coated microparticles and microencapsulation, which has the great advantage of delivering small doses of drug only in the desired site, reducing accumulation and undesired systemic effects, together with a better control on the release rate, by modifying the microenvironment [1]; (iii) encapsulation and manipulations of single cells in aqueous droplets for cell culture, which allows isolating each individual cell in its microenvironement [2]. Droplet generation via segmentation in microfluidic devices has the great advantage with respect to batch methods of ensuring excellent control on size distribution, allowing the generation of almost monodisperse droplets, and on generation rates, at the cost of lower processed volumes.

Annual Review of Fluid Mechanics, 48(1):285–309, 2016 <ref:2601. p. 0
Where the paper says it

innocenti@unipi. it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601.

09483#pg8>

[4] Taotao Fu, Yining Wu, Youguang Ma, and Huai Z Li. Droplet formation and breakup dynamics in microfluidic flow-focusing devices: From dripping to jetting. p. 1

Where the paper says it

Droplet generation via segmentation in microfluidic devices has the great advantage with respect to batch methods of ensuring excellent control on size distribution, allowing the generation of almost monodisperse droplets, and on generation rates, at the cost of lower processed volumes. The generation of microdroplets via segmentation is generally achieved at a junction of separate channels fed with immiscible fluids, generally oil and an aqueous solution, through different possible regimes, namely squeezing, dripping and jetting [3].

Chemical Engineering Science, 84:207–217, 2012 <ref:2601. p. 0
Where the paper says it

innocenti@unipi. it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601.

09483#pg8>

[5] Piotr Garstecki, Howard A Stone, and George M Whitesides. Mechanism for flow-rate controlled breakup in confined geometries: A route to monodisperse emulsions. p. 1

Where the paper says it

Introduction The processes of droplet generation at the milli to micro scale has attracted considerable attention due to the numerous applications in which micro-droplets are involved, such as: (i) lab-on-a-chip devices (miniaturized reproductions of laboratory processes at the micro/milli scale) for sample preparation, mixing, separation and detection; (ii) drug delivery through microparticles, nanoparticles, coated microparticles and microencapsulation, which has the great advantage of delivering small doses of drug only in the desired site, reducing accumulation and undesired systemic effects, together with a better control on the release rate, by modifying the microenvironment [1]; (iii) encapsulation and manipulations of single cells in aqueous droplets for cell culture, which allows isolating each individual cell in its microenvironement [2]. Droplet generation via segmentation in microfluidic devices has the great advantage with respect to batch methods of ensuring excellent control on size distribution, allowing the generation of almost monodisperse droplets, and on generation rates, at the cost of lower processed volumes.

Physical Review Letters, 94(16):164501, 2005 <ref:2601. p. 0
Where the paper says it

innocenti@unipi. it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601.

09483#pg8>

[6] Thomas Cubaud and Thomas G Mason. Capillary threads and viscous droplets in square microchannels. p. 9

Where the paper says it

More details on geometries and boundary conditions are given in the following sections. 2-dimensional Taylor bubble Before studying the droplet generation in a coaxial device, we assess the accuracy of Basilisk in reproducing the dynamics of a Taylor bubble, since the literature on Basilisk applications to problems with bubbles/droplets in microchannels is still very limited to date.

Physics of Fluids, 20(5), 2008 <ref:2601. p. 0
Where the paper says it

it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601. 09483v1 [physics.

09483#pg8>

[7] Jinsong Hua, Baili Zhang, and Jing Lou. Numerical simulation of microdroplet formation in coflowing immiscible liquids. p. 3

Where the paper says it

Even if not always all these aspect are considered rigorously, the literature on numerical approaches to droplet generation in microdevices is rapidly increasing, and different methods and softwares are now commonly used in device design. [7] have simulated coflowing devices with a front-tracking method [8] to track the interface between the two immiscible phases, exploiting mainly the dripping and jetting regimes at different values of the Capillary and Weber numbers.

AIChE Journal, 53(10):2534–2548, 2007 <ref:2601. p. 0
Where the paper says it

innocenti@unipi. it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601.

09483#pg8>

[8] Salih Ozen Unverdi and Grétar Tryggvason. A front-tracking method for viscous, incompressible, multi-fluid flows. p. 3

Where the paper says it

Afkhami and coworkers have explored the use of Volume-of-Fluid (VOF) methods for the interface tracking, together with the geometrical height function method for the calculation of curvature and the estimation of surface tension, in a T-junction [11] and in a co-flowing configuration in a Hele-Shaw cell [12]. A different VOF implementation has been adopted in another work [13] to study the effect of the injection angle in a 3-dimensional cross-flow geometry, while the most widely used numerical tool for such kind of flows probably remains OpenFOAM with its interFoam solver, which is still based on the VOF method, but with a diffuse interface approach [14, 15, 16].

Journal of Computational Physics, 100(1):25–37, 1992 <ref:2601. p. 0
Where the paper says it

it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601. 09483v1 [physics.

09483#pg8>

[9] M De Menech, Piotr Garstecki, F Jousse, and Howard A Stone. Transition from squeezing to dripping in a microfluidic T-shaped junction. p. 3

Where the paper says it

De Menech et al. [9] have analyzed the transition from squeezing to dripping in a T-junction with the phase-field method, which adopts a diffuse interface approach, justified by the low capillary numbers (dominant effect of surface tension) in microfluidics, and relating the breakup dynamics to the upstream pressure variations.

Journal of Fluid Mechanics, 595:141–161, 2008 <ref:2601. p. 0
Where the paper says it

innocenti@unipi. it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601.

09483#pg8>

[10] Long Wu, Michihisa Tsutahara, Lae Sung Kim, and ManYeong Ha. Three-dimensional lattice Boltzmann simulations of droplet formation in a cross-junction microchannel. p. 3

Where the paper says it

[9] have analyzed the transition from squeezing to dripping in a T-junction with the phase-field method, which adopts a diffuse interface approach, justified by the low capillary numbers (dominant effect of surface tension) in microfluidics, and relating the breakup dynamics to the upstream pressure variations. [10] have performed three dimensional simulations with the lattice Boltzmann method for a cross-junction configuration, with a surface tension calculation based on the continuum surface force (CSF) method, with a good comparison with experiments.

International Journal of Multiphase Flow, 34(9):852–864, 2008 <ref:2601. p. 0
Where the paper says it

innocenti@unipi. it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601.

09483#pg8>

[11] Shahriar Afkhami, Alex M Leshansky, and Yuriko Renardy. Numerical investigation of elongated drops in a microfluidic T-junction. p. 1

Where the paper says it

Droplet generation via segmentation in microfluidic devices has the great advantage with respect to batch methods of ensuring excellent control on size distribution, allowing the generation of almost monodisperse droplets, and on generation rates, at the cost of lower processed volumes. The generation of microdroplets via segmentation is generally achieved at a junction of separate channels fed with immiscible fluids, generally oil and an aqueous solution, through different possible regimes, namely squeezing, dripping and jetting [3].

Physics of Fluids, 23(2), 2011 <ref:2601. p. 0
Where the paper says it

it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601. 09483v1 [physics.

09483#pg8>

[12] Shahriar Afkhami and Yuriko Renardy. A volume-of-fluid formulation for the study of co-flowing fluids governed by the Hele-Shaw equations. p. 3

Where the paper says it

Afkhami and coworkers have explored the use of Volume-of-Fluid (VOF) methods for the interface tracking, together with the geometrical height function method for the calculation of curvature and the estimation of surface tension, in a T-junction [11] and in a co-flowing configuration in a Hele-Shaw cell [12]. A different VOF implementation has been adopted in another work [13] to study the effect of the injection angle in a 3-dimensional cross-flow geometry, while the most widely used numerical tool for such kind of flows probably remains OpenFOAM with its interFoam solver, which is still based on the VOF method, but with a diffuse interface approach [14, 15, 16].

Physics of Fluids, 25(8), 2013 <ref:2601. p. 0
Where the paper says it

it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601. 09483v1 [physics.

09483#pg8>

[13] Wei Yu, Xiangdong Liu, Yuanjin Zhao, and Yongping Chen. Droplet generation hydrodynamics in the microfluidic cross-junction with different junction angles. p. 1

Where the paper says it

Droplet generation via segmentation in microfluidic devices has the great advantage with respect to batch methods of ensuring excellent control on size distribution, allowing the generation of almost monodisperse droplets, and on generation rates, at the cost of lower processed volumes. The generation of microdroplets via segmentation is generally achieved at a junction of separate channels fed with immiscible fluids, generally oil and an aqueous solution, through different possible regimes, namely squeezing, dripping and jetting [3].

Chemical Engineering Science, 203:259–284, 2019 <ref:2601. p. 0
Where the paper says it

innocenti@unipi. it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601.

09483#pg8>

[14] Duong A Hoang, Volkert van Steijn, Luis M Portela, Michiel T Kreutzer, and Chris R Kleijn. Modeling of low-capillary number segmented flows in microchannels using OpenFOAM. p. 2

Where the paper says it

However, even if the fluid dynamics of such devices is simple at first sight, given the very low Reynolds numbers involved, which implies that the flows are inherently laminar and can generally be described by the Stokes equations, interfaces can complicate the numerical solution significantly, leading to possible lack of accuracy if not properly handled, or in the worst case to numerical instabilities, due to the amplification of capillary waves. This latter complication, with an explicit treatment of surface tension, can only be overcome at the expense of using very small time steps, 3

In AIP Conference Proceedings, volume 1479, pages 86–89. p. 1
Where the paper says it

The generation of microdroplets via segmentation is generally achieved at a junction of separate channels fed with immiscible fluids, generally oil and an aqueous solution, through different possible regimes, namely squeezing, dripping and jetting [3]. The analysis of different design configurations, geometries and response to variations of physical parameters is crucial for the optimization of the devices and to maintain the control, first of all on the production regime, secondly on droplet volume, production rates and monodispersity.

American Institute of Physics, 2012 <ref:2601. p. 0
Where the paper says it

it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601. 09483v1 [physics.

09483#pg8>

[15] Duong A Hoang, Volkert van Steijn, Luis M Portela, Michiel T Kreutzer, and Chris R Kleijn. Benchmark numerical simulations of segmented two-phase flows in microchannels using the Volume of Fluid method. p. 8

Where the paper says it

Accurate computation of the curvature is carried out using the height-function method [19]. The device geometry is defined in Basilisk through the embedded boundary method (EBM), originally proposed in [25, 26], and widely used in Basilisk literature for moving boundaries [27], solidification modelling [28], and two-phase flows with complex geometries [29].

Computers & Fluids, 86:28–36, 2013 <ref:2601. p. 0
Where the paper says it

innocenti@unipi. it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601.

09483#pg8>

[16] Maryam Fatehifar, Alistair Revell, and Masoud Jabbari. Non-Newtonian droplet generation in a cross-junction microfluidic channel. p. 5

Where the paper says it

Modeling and governing equations We describe the dynamics of droplet generation in a microfluidic device, where two non-miscible fluids enter from separate channels, come in contact at a junction, and flow out from the same channel. The physical parameters characterizing the problem are the viscosities and densities of the two fluids, µi and ρi , and surface tension σ.

Polymers, 13(12):1915, 2021 <ref:2601. p. 0
Where the paper says it

innocenti@unipi. it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601.

09483#pg8>

[17] Sara Tomasi Masoni, Alessandro Mariotti, Chiara Galletti, Roberto Mauri, Maria Vittoria Salvetti, and Elisabetta Brunazzi. Formation of sodium-alginate droplets in an X-microdevice: Characterization of the pinching efficiency. p. 9

Where the paper says it

of the equilibrium contact angle, which depends on the specific properties of the fluid and of the solid surface, was not carried out, as it would require a more detailed characterization of the experimental conditions, which is beyond the scope of the present work, as the comparison is performed with an experiment from the literature. For the velocity and pressure fields we set an inlet boundary condition with constant velocity at the entrance of the channel, a no-slip condition at the walls, and an outflow condition with fixed pressure at the outlet of the channel.

Physics of Fluids, 36(9), 2024 <ref:2601. p. 0
Where the paper says it

it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601. 09483v1 [physics.

09483#pg8>

[18] David Gabriel Harispe and Pablo A Kler. Accurate numerical prototypes of microfluidic droplet generators with open source tools. p. 0

Where the paper says it

In this work we have evaluated the suitability of the open-source software Basilisk to accurately predict microdroplet generation by segmentation. We have validated the numerical tool with analytical solutions for the dynamics of droplets in confined flows, namely with Bretherton theory, and by comparison with literature experimental results.

Computers & Fluids, 281:106366, 2024 <ref:2601. p. 0
Where the paper says it

innocenti@unipi. it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601.

09483#pg8>

[19] Stéphane Popinet. An accurate adaptive solver for surfacetension-driven interfacial flows. p. 8

Where the paper says it

Accurate computation of the curvature is carried out using the height-function method [19]. The device geometry is defined in Basilisk through the embedded boundary method (EBM), originally proposed in [25, 26], and widely used in Basilisk literature for moving boundaries [27], solidification modelling [28], and two-phase flows with complex geometries [29].

Journal of Computational Physics, 228(16):5838–5866, 2009 <ref:2601. p. 0
Where the paper says it

it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601. 09483v1 [physics.

09483#pg8>

[20] Stéphane Popinet. Gerris: a tree-based adaptive solver for the incompressible Euler equations in complex geometries. p. 5

Where the paper says it

), the additional parameters characterizing the flow are the inlet velocities of the two fluids, Uc and Ud, and a characteristic dimension of the channels, typically the diameter, D, in coaxial configurations or the channel height, H, in square section channels. Based on these physical, geometrical and flow parameters, four dimensionless groups can be formed: firstly the viscosity and density ratios, respectively µd/µc and ρd/ρc; secondly the Reynolds and Capillary number, that for these kind of flows can be defined based on the continuous phase properties as follows Rec = ρcUcD µc , Cac = µcUc σ (1) An alternative, quite common in microfluidics literature, is to replace one of these two dimensionless number with the Weber number, defined as follows: W ec = ρcU 2 c D σ = Rec · Cac (2) The two fluids are governed by the Navier-Stokes incompressible equations with variable density and viscosity, which in their dimensionless form 6

Journal of Computational Physics, 190(2):572–600, 2003 <ref:2601. p. 0
Where the paper says it

it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601. 09483v1 [physics.

09483#pg8>

[21] Cyril W Hirt and Billy D Nichols. Volume of fluid (VOF) method for the dynamics of free boundaries. p. 3

Where the paper says it

[10] have performed three dimensional simulations with the lattice Boltzmann method for a cross-junction configuration, with a surface tension calculation based on the continuum surface force (CSF) method, with a good comparison with experiments. Afkhami and coworkers have explored the use of Volume-of-Fluid (VOF) methods for the interface tracking, together with the geometrical height function method for the calculation of curvature and the estimation of surface tension, in a T-junction [11] and in a co-flowing configuration in a Hele-Shaw cell [12].

Journal of Computational Physics, 39(1):201–225, 1981 <ref:2601. p. 0
Where the paper says it

it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601. 09483v1 [physics.

09483#pg8>

[22] Grétar Tryggvason, Ruben Scardovelli, and Stéphane Zaleski. Direct Numerical Simulations of Gas–Liquid Multiphase Flows. p. 0

Where the paper says it

We have validated the numerical tool with analytical solutions for the dynamics of droplets in confined flows, namely with Bretherton theory, and by comparison with literature experimental results. We have then performed several campaigns of numerical simulations for a coaxial device, analyzing the different regimes of droplet generation, and evaluating how the physical and flow parameters affect the production mechanisms and the diameters of the generated droplets.

Cambridge University Press, 2011 <ref:2601. p. 0
Where the paper says it

Analysis and simulations of droplet generation regimes in a coaxial microfluidic device Alessio Innocenti∗ , Andrea Poggi, Simone Camarri, Maria Vittoria Salvetti University of Pisa, Dipartimento di Ingegneria Civile e Industriale, Largo Lucio Lazzarino, 56122, Pisa, Italy Abstract The generation of microdroplets via segmentation in microfluidic devices is of interest in many applications, from biochemical to pharmaceutical. This technique permits indeed much higher control on the droplet size, uniformity and generation rate than in standard batch generation processes.

09483#pg8>

[23] Eugenio Aulisa, Sandro Manservisi, Ruben Scardovelli, and Stephane Zaleski. Interface reconstruction with least-squares fit and split advection in three-dimensional Cartesian geometry. p. 8

Where the paper says it

The method embeds a sharp representation of a solid surface on a regular Cartesian grid. The reconstruction of the solid interface is done using a piecewise linear reconstruction, using a signed distance function sampled on the vertices of the Cartesian grid for the geometrical properties.

Journal of Computational Physics, 225(2):2301–2319 <ref:2601. p. 0
Where the paper says it

it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601. 09483v1 [physics.

09483#pg8>

[24] Jeremiah U Brackbill, Douglas B Kothe, and Charles Zemach. A continuum method for modeling surface tension. p. 3

Where the paper says it

[9] have analyzed the transition from squeezing to dripping in a T-junction with the phase-field method, which adopts a diffuse interface approach, justified by the low capillary numbers (dominant effect of surface tension) in microfluidics, and relating the breakup dynamics to the upstream pressure variations. [10] have performed three dimensional simulations with the lattice Boltzmann method for a cross-junction configuration, with a surface tension calculation based on the continuum surface force (CSF) method, with a good comparison with experiments.

Journal of Computational Physics, 100(2):335–354, 1992 <ref:2601. p. 0
Where the paper says it

it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601. 09483v1 [physics.

09483#pg8>

[25] Hans Johansen and Phillip Colella. A Cartesian grid embedded boundary method for Poisson’s equation on irregular domains. p. 8

Where the paper says it

The device geometry is defined in Basilisk through the embedded boundary method (EBM), originally proposed in [25, 26], and widely used in Basilisk literature for moving boundaries [27], solidification modelling [28], and two-phase flows with complex geometries [29]. The method embeds a sharp representation of a solid surface on a regular Cartesian grid.

Journal of Computational Physics, 147(1):60–85, 1998 <ref:2601. p. 0
Where the paper says it

it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601. 09483v1 [physics.

09483#pg8>

[26] Peter Schwartz, Michael Barad, Phillip Colella, and Terry Ligocki. A Cartesian grid embedded boundary method for the heat equation and Poissons equation in three dimensions. p. 8

Where the paper says it

The device geometry is defined in Basilisk through the embedded boundary method (EBM), originally proposed in [25, 26], and widely used in Basilisk literature for moving boundaries [27], solidification modelling [28], and two-phase flows with complex geometries [29]. The method embeds a sharp representation of a solid surface on a regular Cartesian grid.

Journal of Computational Physics, 211(2):531–550, 2006 <ref:2601. p. 0
Where the paper says it

it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601. 09483v1 [physics.

09483#pg8>

[27] Arthur R Ghigo, Stéphane Popinet, and Anthony Wachs. A conservative finite volume cut-cell method on an adaptive Cartesian tree grid for moving rigid bodies in incompressible flows. p. 8

Where the paper says it

The reconstruction of the solid interface is done using a piecewise linear reconstruction, using a signed distance function sampled on the vertices of the Cartesian grid for the geometrical properties. The discrete operators in the cut cell are then properly defined with the finite volume method with 2nd order accuracy [29] for single phase flow / 1st order accuracy when coupled with the VOF method.

2021 <ref:2601.09483#pg8>

[28] Alexandre Limare, Stéphane Popinet, Christophe Josserand, Zhonghan Xue, and A Ghigo. A hybrid level-set/embedded boundary method ap33 implied to solidification-melt problems. p. 8

Where the paper says it

Accurate computation of the curvature is carried out using the height-function method [19]. The device geometry is defined in Basilisk through the embedded boundary method (EBM), originally proposed in [25, 26], and widely used in Basilisk literature for moving boundaries [27], solidification modelling [28], and two-phase flows with complex geometries [29].

Journal of Computational Physics, 474:111829, 2023 <ref:2601. p. 0
Where the paper says it

it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601. 09483v1 [physics.

09483#pg8>

[29] Mathilde Tavares, Christophe Josserand, Alexandre Limare, Jose Ma Lopez-Herrera, and Stéphane Popinet. A coupled VOF/embedded boundary method to model two-phase flows on arbitrary solid surfaces. p. 8

Where the paper says it

The discrete operators in the cut cell are then properly defined with the finite volume method with 2nd order accuracy [29] for single phase flow / 1st order accuracy when coupled with the VOF method. Concerning the boundary condition of the fluid volume fraction at the cut cell, a particular treatment must be adopted when in the same cell there are the two liquid phases and the solid, indeed a condition on the contact angle need to be set [30, 31].

Computers & Fluids, 278:106317, 2024 <ref:2601. p. 0
Where the paper says it

innocenti@unipi. it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601.

09483#pg8>

[30] Shahriar Afkhami, Stephane Zaleski, and Markus Bussmann. A meshdependent model for applying dynamic contact angles to VOF simulations. p. 8

Where the paper says it

The discrete operators in the cut cell are then properly defined with the finite volume method with 2nd order accuracy [29] for single phase flow / 1st order accuracy when coupled with the VOF method. Concerning the boundary condition of the fluid volume fraction at the cut cell, a particular treatment must be adopted when in the same cell there are the two liquid phases and the solid, indeed a condition on the contact angle need to be set [30, 31].

Journal of Computational Physics, 228(15):5370–5389 <ref:2601. p. 0
Where the paper says it

it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601. 09483v1 [physics.

09483#pg8>

[31] Dominique Legendre and Marco Maglio. Comparison between numerical models for the simulation of moving contact lines. p. 9

Where the paper says it

of the equilibrium contact angle, which depends on the specific properties of the fluid and of the solid surface, was not carried out, as it would require a more detailed characterization of the experimental conditions, which is beyond the scope of the present work, as the comparison is performed with an experiment from the literature. For the velocity and pressure fields we set an inlet boundary condition with constant velocity at the entrance of the channel, a no-slip condition at the walls, and an outflow condition with fixed pressure at the outlet of the channel.

Computers & Fluids, 113:2–13, 2015 <ref:2601. p. 0
Where the paper says it

innocenti@unipi. it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601.

09483#pg8>

[32] Jose-Maria Fullana, Yue Ling, Stéphane Popinet, and Christophe Josserand. Droplet in micro-channels: A numerical approach using an adaptive two phase flow solver. p. 3

Where the paper says it

A different VOF implementation has been adopted in another work [13] to study the effect of the injection angle in a 3-dimensional cross-flow geometry, while the most widely used numerical tool for such kind of flows probably remains OpenFOAM with its interFoam solver, which is still based on the VOF method, but with a diffuse interface approach [14, 15, 16]. It is worth mentioning that, in parallel, research is also being conducted using commercial codes, 4

In 1st Pan-American Congress on Computational Mechanics - PANACM 2015, 2015 <ref:2601.09483#pg8>

[33] Francis Patton Bretherton. The motion of long bubbles in tubes. p. 9

Where the paper says it

More details on geometries and boundary conditions are given in the following sections. 2-dimensional Taylor bubble Before studying the droplet generation in a coaxial device, we assess the accuracy of Basilisk in reproducing the dynamics of a Taylor bubble, since the literature on Basilisk applications to problems with bubbles/droplets in microchannels is still very limited to date.

Journal of Fluid Mechanics, 10(2):166–188, 1961 <ref:2601. p. 0
Where the paper says it

innocenti@unipi. it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601.

09483#pg8>

[34] Pascale Aussillous and David Quéré. Quick deposition of a fluid on the wall of a tube. p. 8

Where the paper says it

For more details on the numerical implementation of the contact angle condition in Basilisk, see [29]. In all the present simulations, when the contact between the interface and the wall is present, we have used an equilibrium contact angle of αw = 30◦ (measured between the wall and the interface in the continuous phase), which is within the typical range of values adopted in numerical simulations [17, 16, 15].

Physics of fluids, 12(10):2367–2371, 2000 <ref:2601. p. 0
Where the paper says it

it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601. 09483v1 [physics.

09483#pg8>

[35] Wenjie Lan, Shaowei Li, and Guangsheng Luo. Numerical and experimental investigation of dripping and jetting flow in a coaxial microchannel. p. 0

Where the paper says it

We have then performed several campaigns of numerical simulations for a coaxial device, analyzing the different regimes of droplet generation, and evaluating how the physical and flow parameters affect the production mechanisms and the diameters of the generated droplets. Finally we have proposed new scaling laws for the prediction of droplet diameters in the dripping and jetting regimes, refining existing ones by taking ∗Corresponding author Email address: alessio.

Chemical Engineering Science, 134:76–85, 2015 <ref:2601. p. 0
Where the paper says it

innocenti@unipi. it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601.

09483#pg8>

[36] Andrew S Utada, Alberto Fernandez-Nieves, Howard A Stone, and David A Weitz. Dripping to jetting transitions in coflowing liquid streams. p. 3

Where the paper says it

Even if not always all these aspect are considered rigorously, the literature on numerical approaches to droplet generation in microdevices is rapidly increasing, and different methods and softwares are now commonly used in device design. [7] have simulated coflowing devices with a front-tracking method [8] to track the interface between the two immiscible phases, exploiting mainly the dripping and jetting regimes at different values of the Capillary and Weber numbers.

Physical Review Letters, 99(9):094502, 2007 <ref:2601. p. 0
Where the paper says it

innocenti@unipi. it (Alessio Innocenti) Preprint submitted to Computers and Fluids January 15, 2026 arXiv:2601.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Accurate prediction of droplet generation regimes in coaxial microfluidic devices can be achieved by evaluating open-source software like Basilisk against analytical solutions from Bretherton theory and experimental results.

  2. The improved AI system can analyze physical and flow parameters to predict the different regimes of droplet generation, specifically squeezing, dripping, and jetting, by mapping them onto Capillary number and Weber number spaces.

  3. The system can propose new scaling laws for predicting droplet diameters in the dripping and jetting regimes by incorporating additional physical effects such as the viscosity ratio into existing empirical relations.

  4. The AI system can accurately determine the equivalent diameter of generated droplets using Basilisk tag functions to calculate area, providing a quantitative measure of droplet size.

  5. The improved system can perform regime mapping based on Capillary number and Weber number to identify transition zones between dripping and jetting regimes, which offers valuable insights for device design.

Abstract

The generation of microdroplets via segmentation in microfluidic devices is of interest in many applications, from biochemical to pharmaceutical. This technique permits indeed much higher control on the droplet size, uniformity and generation rate than in standard batch generation processes. In this work we have evaluated the suitability of the open-source software Basilisk to accurately predict microdroplet generation by segmentation. We have validated the numerical tool with analytical solutions for the dynamics of droplets in confined flows, namely with Bretherton theory, and by comparison with literature experimental results. We have then performed several campaigns of numerical simulations for a coaxial device, analyzing the different regimes of droplet generation, and evaluating how the physical and flow parameters affect the production mechanisms and the diameters of the generated droplets. Finally we have proposed new scaling laws for the prediction of droplet diameters in the dripping and jetting regimes, refining existing ones by taking into account additional physical effects, like the viscosity ratio.

Related papers