A Low-Complexity 200 Mbit/s Full-Duplex Digital Link Over a Single Coaxial Cable for Laboratory Instrumentation
summary
The gist
A low-complexity bidirectional digital interconnect that enables simultaneous transmission and reception of baseband logic signals over a single coaxial cable is presented for laboratory…
In short
The study developed a low-complexity bidirectional digital interconnect for laboratory instruments, achieving full-duplex communication at 200 Mbit/s over a 10-meter RG-178 coaxial cable. The design uses only a passive resistive hybrid and two commodity ICs to enable simultaneous transmission and reception.
Key concepts
- Passive Resistive Hybrid
- This is a circuit made of resistors that acts like a directional bridge on the coaxial cable. It is used here to separate the transmitted signal from the received signal, allowing both directions (sending and receiving) to happen at once without interference.
- Directional Bridge Topology
- The circuit uses a specific layout for the resistive hybrid, based on a known topology. This structure helps isolate the voltage traveling backward along the cable from the voltage being sent forward by a signal source.
- Full-Duplex Operation
- This means that data can be sent and received simultaneously over the same single coaxial cable. The system is designed to handle 200 Megabits per second in both directions at the same time, which is crucial for efficient digital communication.
Terminology used across episodes
This episode discusses
- A Low-Complexity 200 Mbit/s Full-Duplex Digital Link Over a Single Coaxial Cable for Laboratory Instrumentation · Paper Radio
The paper
A Low-Complexity 200 Mbit/s Full-Duplex Digital Link Over a Single Coaxial Cable for Laboratory Instrumentation · Read on arXiv
M. Wiebusch
GSI Helmholtzzentrum für Schwerionenforschung GmbH
Modern full-duplex communication systems, such as Gigabit Ethernet, enable high data rates over challenging transmission media but require sophisticated circuitry and non-trivial digital interfaces. For laboratory instrumentation, the objective may instead be to achieve moderate-bandwidth full-duplex communication over short, well-controlled coaxial cables with minimal circuit and interface complexity. We present a low-complexity bidirectional digital interconnect that enables simultaneous transmission and reception of baseband logic signals over a single coaxial cable. The circuit combines a discrete passive resistive hybrid providing line termination and directional separation, a single logic gate as line driver, and a commercial differential receiver used as a comparator. No modulation, transformer coupling, adaptive calibration, or active analog or digital echo cancellation is required. The design target is full-duplex operation at 200 MBit/s over 10 m of standard RG-178 cable. An analytical treatment of the hybrid network determines the system parameter that maximizes the differential signal amplitude at the receiver, while circuit simulations predict the deterministic timing errors resulting from imperfect directional separation. Experimental measurements confirm the predicted deterministic jitter and show good agreement with the simulation results. For typical laboratory coaxial cables up to 10 m, the measured peak-to-peak edge timing error remains below 1.2 ns. A bidirectional transmission experiment with randomized data demonstrates a clearly open eye diagram. It was found that the transceiver inherently provides loopback functionality when the transmission line is left open. The proposed approach provides a simple, protocol-independent bidirectional physical link which may be useful in laboratory instrumentation where cable routing is constrained.
Transcript
Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.
Kai: I'm Kai.
Mira: And I'm Mira, here with Lev.
Kai: We're looking at the paper: "A Low-Complexity 200 Mbit/s Full-Duplex Digital Link Over a Single Coaxial Cable for Laboratory Instrumentation".
Mira: Here's the gist of the paper. A low-complexity bidirectional digital interconnect that enables simultaneous transmission and reception of baseband logic signals over a single coaxial cable is presented for laboratory instrumentation The targeted design performance is fullduplex operation at 200 Mbit s−1 over 10 m of standard RG-178 cable.
Kai: System Design and Components The proposed circuit combines a discrete passive resistive hybrid providing line termination and directional separation, a single logic gate as line driver, and a commercial differential receiver used as a comparator.
Mira: The design target is full-duplex operation at 200 Mbit s−1 over 10 m of standard RG-178 cable.
Kai: The circuit consists only of a passive resistor bridge circuit (a so-called hybrid) and two commodity ICs that can be readily integrated on a printed circuit board (PCB) to establish digital device-to-device communication.
Paper summary: Kai: So, to recap this paper, "A Low-Complexity two hundred Mbit/s Full-Duplex Digital Link Over a Single Coaxial Cable for Laboratory Instrumentation", they are proposing a solution for getting full-duplex digital communication over just one coaxial cable <ref:2603.18848#pg1,A Low-Complexity 200 Mbit/s Full-Duplex Digital Link Over a>.
Mira: The core claim is achieving this at two hundred Megabits per second, but the design philosophy is low complexity, avoiding modulation and active echo cancellation entirely <ref:2603.18848#pg1>. This makes it suitable for lab instrumentation where simplicity matters more than raw speed or ultra-long distance.
Lev: They use a discrete passive resistive hybrid for line termination and directional separation, plus one logic gate as the driver and a commercial differential receiver as the comparator to achieve bidirectional communication simultaneously over the medium.
Kai: The paper focuses on showing that this architecture works for laboratory settings, aiming for moderate-bandwidth full-duplex operation over short, controlled coaxial cables with minimal circuit overhead.
Mira: The main implication here is demonstrating a viable path toward low-complexity digital device-to-device communication using simple passive elements when compared to more complex commercial solutions like RS485 or CAN.
Lev: From an error correction standpoint, the results show deterministic edge timing errors in simulation, which they quantify as a peak-to-peak timing spread of about five hundred picoseconds. This is the noise floor you have to deal with when you try to build this on actual hardware for real data transmission.
Kai: They also measured the jitter versus cable length and found that for cables shorter than six meters, the timing error swings between two hundred picoseconds and eight hundred picoseconds.
Mira: As the cable gets longer, they noted an additional timing error appears due to frequency-dependent cable losses, which degrades those signal edges. When they measure this experimentally on longer cables, the peak-to-peak timing jitter increases to about one point nine nanosecond while still keeping the eye open.
Lev: That one point nine nanosecond jitter is what you have to budget for if you try to run this over a real piece of RG-one hundred seventy-eight cable for a bit longer than six meters, even with this simple design <ref:2603.18848#pg3>.
Kai: And they also showed that without any extra components added, the transceiver provides an inherent loopback function. The signal transmitted out is received back by the same device when no external cable is connected.
Mira: That loopback functionality is useful for testing link integrity before you introduce a second device or a proper termination load to see how the system behaves in isolation.
Lev: I wonder if that inherent loopback really means much in practice when you're trying to set up a full-duplex communication link between two distinct pieces of equipment, but it’s good for initial component testing.
Conclusion: Kai: So, looking at the paper "A Low-Complexity two hundred Mbit/s Full-Duplex Digital Link Over a Single Coaxial Cable for Laboratory Instrumentation", the main point is that you can build this kind of link using just a few simple parts <ref:2603.18848#pg1,A Low-Complexity 200 Mbit/s Full-Duplex Digital Link Over a>.
Mira: They show that this design successfully achieves full-duplex operation at two hundred Megabits per second over ten meters of RG-one hundred seventy-eight cable, relying on a passive resistive hybrid and basic digital components <ref:2603.18848#pg3>.
Lev: The implication is that for specific lab instrumentation needs, you can achieve high data rates with very low circuit complexity compared to what you might see in commercial PHY ICs like the 1000BASE-T example they compare against <ref:2603.18848#pg3>.
Kai: The design targets a specific niche: moderate bandwidth over short, well-controlled coaxial cables where you don't need the massive infrastructure of gigabit Ethernet or other high-speed standards.
Mira: Ultimately, this work shows that you can create a functional digital interconnect using very basic components without needing modulation or active cancellation circuitry for this type of application.
Lev: The limitation they state is that while the design is simple, it doesn't inherently solve the problem of managing significant frequency-dependent losses over much longer distances where those timing errors become unmanageable.
Kai: So, in short, it’s a proof of concept for low-complexity bidirectional digital links over coaxial cable for short runs, focusing on simplicity and direct device communication.
More episodes
- 2611.14082-Two atoms with strong light-induced dipolar interactions
- 2611.14040-Characterization of BNLs 20 and 30 micrometer thick LGADs for the Electron Ion Collider
- 2611.13399-Lift-element-based dynamic network of vortex gust-airfoil interactions
- 2611.13476-Hopfion Superlattices in 3D Twisted Moir'e Light Fields
- 2611.13642-Investigation of the timing performance of double-sided p-type 3D silicon sensors produced by CNM
- 2611.13830-SiPM optical readout of a PICOSEC Micromegas precise timing detector
- 2611.14152-Where are the shortest-path nodes in spatial networks?
- 2611.14219-Sub-Ice: semi-automated mapping of basal channels from ice shelf surface elevation data
- 2611.16341-SUMNO: Spatially Unrolled Multigrid Neural Operator for Fluid Flow Surrogates
- 2611.16090-Multi-UTE Myelin Fraction Mapping: Repeatability and Cross-Field-Strength Reproducibility at 1.5T and 3T