Euclid Data Release 1 (DR1). NIR astrometric calibration

arXiv:2611.16486 · astro-ph.IM, astro-ph.CO · Submitted 2026-11-12 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Astrophysics. The day in astrophysics: observations, models and what the data forces.

Vera: We're looking at the paper: "Euclid Data Release 1 (DR1). NIR astrometric calibration".

Jocelyn: Here's the gist of the paper. This paper presents the methodology and results of the astrometric calibration applied to the Euclid Near-Infrared (NIR) images in the Euclid Data Release 1, focusing on techniques used to model and correct instrumental distortions, as well as assessment of calibration quality The achieved accuracy is 30 mas for 97% of the total area, thus exceeding the requirements for Data Release 1 Calibration Methodology The astrometric calibration pipeline relies on the Scamp software to compute the distortion and update associated keywords in the headers of the FITS frames This process utilizes either the PV formalism or a SIP formalism to model instrumental distortions, depending on whether it is working in sky coordinates or directly in focal plane terms The PV formalism maps pixel coordinates from that detector to intermediate world coordinates using a polynomial with order N = 3 In contrast, the SIP formalism describes the distortion directly in the focal plane without relying on a tangent-plane projection The relevant quantities are defined as px and py are the coordinates of the reference pixel, corresponding to the CRPIX keywords in the FITS files Astrometric Residual Analysis The analysis of astrometric residuals involves calculating several quantities derived from positional differences between N detections and their matched reference sources The average offset is given by the formula ⟨∆α∗⟩ = 1/N Σ i=1 ∆α∗i, ⟨∆δ⟩ = 1/N Σ i=1 ∆δi The standard deviation measures the spread of positional offsets around the mean, indicating calibration precision The RMS offset represents the total calibration accuracy (bias + precision) as RMS2 = RMS2α∗ + RMS2δ/2 Analysis of stacked catalogues confirms that the average offset to the reference catalogue is negligible, being within 2 mas Geometric Distortion Verification The paper verifies whether the geometric distortion is calibrated within 0.015% over scales of 3 arcmin This verification involves comparing pairs of stars separated by a distance dref between 2′5 and 3′5 in the Gaia DR3 catalogue with their corresponding separations in the NISP catalogues In all stacked catalogues examined here, the RMS of ν is less than 0.01% The analysis also evaluates how well the assumption of a constant presolution aligns with actual distortion observed in dithers Mitigation Strategies and Future Work A limitation identified in DR1 is the impact of persistence masking on astrometric accuracy, particularly affecting detectors DET13 and DET14 A mitigation strategy involving a refined persistence flagging criterion based on persistence intensity and radius around detections has been developed and applied in subsequent processing For future data releases, improvements include a refined persistence masking approach and exploration of alternative distortion evaluation methods that reduce the complexity of the distortion model while preserving the calibration quality A simplified distortion model with fewer free parameters would still allow for a reduction in computational complexity, but fitting only linear terms increases the residuals, necessitating a second-order polynomial fit to maintain comparable accuracy The Euclid NISP astrometric calibration in DR1 demonstrates high precision and stability, with well-characterized residuals and identified pathways for further improvement The results provide a solid foundation for subsequent data releases, ensuring accurate celestial source positioning, which is essential for the mission’s scientific objectives Acknowledgements The Euclid Consortium acknowledges the European Space Agency and a number of agencies and institutes that have supported the development of Euclid This work has made use of the Euclid Data Release 1 (DR1) from the European Space Agency (ESA) mission Euclid This research makes use of ESA Datalabs (datalabs.esa.int), an initiative by ESA’s Data Science and Archives Division in the Science and Operations Department, Directorate of Science This work has made use of data from the European Space Agency (ESA) mission Gaia processed by the Gaia Data Processing and Analysis Consortium (DPAC, https://www.cosmos.esa.int/web/gaia/dpac/consortium) Funding for the DPAC has been provided by national institutions, in particular the institutions participating in the Gaia Multilateral Agreement The Euclid Consortium acknowledges the European Space Agency and a number of agencies and institutes that have supported the development of Euclid, in particular the Agenzia Spaziale Italiana, the Austrian Forschungsförderungsgesellschaft funded through BMIMI, the Belgian Science Policy, the Canadian Euclid Consortium, the Deutsches Zentrum für Luft- und Raumfahrt, the DTU Space and the Niels Bohr Institute in Denmark A complete and detailed list is available on the Euclid web site (www.euclid-ec.org/consortium/community/) The Euclid Collaboration acknowledges M.

Vera: Radovich et al.: NIR astrometric calibration The paper has presented the methodology and results of the astrometric calibration applied to the NISP data in Euclid DR1 References Bertin, E.

Jocelyn: 2006, in ASP Conference Series, Vol.

Vera: 351, Astronomical Data Analysis Software and Systems XV, ed.

Title and authors: Vera: We’re looking at the paper "Euclid Data Release one NIR astrometric calibration," and it basically boils down to how they cleaned up all those instrumental distortions from the near-infrared images using these sophisticated modeling techniques.

Jocelyn: They use these methods, either a PV formalism or a SIP formalism depending on whether they were working in sky coordinates or focal plane terms.

Vera: They achieved thirty mas accuracy for ninety-seven percent of the total area, which is a significant result for mapping out the sky in this band <ref:2611.16486#pg1,for 97% of the total area>.

Jocelyn: That level of precision is what you need when you're trying to measure subtle effects in these deep infrared fields.

Subrahmanyan: From a cosmological standpoint, if the error bar is too large, the signal gets washed out by instrument noise, and that directly affects our ability to constrain structure formation models.

Subrahmanyan: Identifying those detector-specific issues allows us to plan better hardware upgrades or software patches directly targeting those instrumental problems.

The paper's summary: Vera: So, let's talk about how they suggest fixing those lingering problems from Data Release one in this paper on "Euclid Data Release one NIR astrometric calibration."

Jocelyn: Right, they aren't just pointing out where it went wrong; they’re offering ways to make the correction better for future data.

Subrahmanyan: From a cosmological standpoint, if we can tighten these error bars further, it directly translates to a more precise picture of structure formation and how matter clumps together in the universe.

Vera: They suggest improving the distortion modeling by incorporating a second-order polynomial fit into those simplified distortion models.

Jocelyn: That means they’re finding a way to reduce the computational complexity while still getting calibration accuracy that's comparable to using a full polynomial model.

Subrahmanyan: That efficiency is important because it lets us process more data without losing that precision we need for cosmological constraints.

Vera: They also have this enhanced persistence masking strategy where they only discard pixels if the pixel intensity within a specific radius around the detection center exceeds a set threshold.

Jocelyn: So instead of just using a blanket rule, they’re being smarter about which pixels to throw away based on how persistent they are in the image.

Subrahmanyan: That sounds like it could save you from losing actual sources that might be important for studying galaxy clustering.

Vera: They also proposed an iterative three sigma clipping approach across focal plane cells and one dimensional strips to compute mean offsets and standard deviations.

Jocelyn: So they’re looking at the spatial mapping of residuals in a more robust way, making sure the estimation of distortion parameters is stable even when source densities are uneven.

Subrahmanyan: Stability in those geometric parameters is key; if those numbers keep jumping around, it makes predicting cosmic structure evolution much harder.

Vera: They also introduced an advanced parallax recovery method using a least squares fit between the NISP and Gaia DR3 parallaxes to determine zero point offsets more precisely.

Jocelyn: That means they can get a better handle on the absolute distance measurements of stars without biasing them too much, which is crucial for understanding stellar populations.

Subrahmanyan: Preserving the full amplitude of that stellar parallax signal in both bands is vital for setting accurate distances across large volumes of space.

Vera: They even developed a simplified distortion model that uses only a constant presolution and fits only linear terms for each dither, though they found this actually increased residuals compared to the full polynomial fit.

Jocelyn: So it shows that fitting less is not always better if you need high precision across all of your data points.

Subrahmanyan: It confirms what we suspected about instrumental behavior; it’s more complex than just a simple linear shift between exposures, so you need the higher order terms.

Vera: They flag a limitation, though: the paper doesn't fully detail how these new methods will handle the persistence masking issue on detectors DET13 and DET14 going forward.

Jocelyn: That’s a fair point; they solve the modeling part, but that specific detector artifact still needs a dedicated fix for future releases.

Subrahmanyan: So the next step is clearly applying these new models to get better data, but tackling those specific hardware artifacts remains a necessary piece of the engineering puzzle.

The paper's improvements: Vera: So we’re wrapping up this paper on "Euclid Data Release one (DR1) NIR astrometric calibration," and it really boils down to how they cleaned up those instrumental distortions from the near-infrared images using these sophisticated modeling techniques.

Jocelyn: Right, so they established a very high level of accuracy for that calibration, achieving thirty mas for ninety-seven percent of the area <ref:2611.16486#pg1,30 mas for 97% of the>.

Subrahmanyan: That's a solid number to start with; it shows that the basic mapping from pixel to sky coordinate is pretty robust across most of the survey.

Vera: They also showed that their geometric distortion was calibrated within zero point one five percent over scales of three arcmin, which is pretty tight <ref:2611.16486#pg3>.

Jocelyn: Comparing those star separations against the Gaia catalogue confirms that the instrument isn't introducing major systematic stretching or squeezing across those local regions.

Vera: They also addressed a limitation they found in DR1: the impact of persistence masking on detectors DET13 and DET14.

Jocelyn: So they’re not just reporting wins; they are clearly showing where the system still has specific weaknesses that need dedicated fixes for future data releases.

Vera: They suggested a refinement in the masking strategy based on persistence intensity and radius around detections instead of just using a fixed threshold.

Jocelyn: That means they’re being smarter about which pixels to discard when dealing with those noisy, persistent areas in the image.

Subrahmanyan: It’s good engineering; you want to keep as much information as possible while still filtering out the noise that doesn't contribute to accurate astrometry.

Vera: They also explored a simplified distortion model using only linear terms for each dither, and they found that this increased the residuals compared to their full polynomial fit.

Jocelyn: It proves that fitting less is not always better when you need high precision across all of your data points.

Subrahmanyan: That confirms what we suspected about instrumental behavior; it’s more complex than just a simple linear shift between exposures, so you need the higher order terms.

Vera: So, in summary, this paper on "Euclid Data Release one (DR1) NIR astrometric calibration" gives us a very high-precision foundation for the survey data <ref:2611.16486#pg1>.

Jocelyn: It sets a strong benchmark for what we expect from the next generation of Euclid observations.

Conclusion: Vera: So we're wrapping up our look at "Euclid Data Release one (DR1) NIR astrometric calibration," and what we saw is that they established a very high precision foundation for the survey data.

Jocelyn: It means they’ve really tightened up how the telescope positions everything on the sky using both PV and SIP formalisms.

Subrahmanyan: And if you get that level of positional accuracy, it gives us a much cleaner input for any cosmological models we try to build later on.

Vera: They showed that their geometric distortion was calibrated within zero point one five percent over scales of three arcmin, which is pretty tight <ref:2611.16486#pg3>.

Jocelyn: It proves that fitting less is not always the right choice when you need high precision across all of your data points.

Vera: So, in summary, this paper on "Euclid Data Release one (DR1) NIR astrometric calibration" gives us a very high-precision foundation for the survey data.

Vera: It gives us confidence in the input data before we move on to the next layer of scientific analysis, like looking at galaxy clustering or weak lensing.

Jocelyn: It’s a necessary step in ensuring that what we measure is truly coming from the sky and not just an artifact of how our telescope was pointed.

Subrahmanyan: And that’s the main thing; reliable positioning is fundamental to making any claim about how fast the universe is expanding or how matter clumps together.

European Space Agency (ESA) · Caltech/IPAC

astro-ph.IM, astro-ph.CO

Submitted: 2026-11-12

Updated: 2026-11-18

Comments: Paper intended for the A&A Special Issue "Euclid First Data Release''(12 pages, 12 figures)

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 91/100

The gist: This paper presents the methodology and results of the astrometric calibration applied to the Euclid Near-Infrared (NIR) images in the Euclid Data Release 1…

Key concepts

PV Formalism
The Polynomial Variation (PV) formalism models instrumental distortion by mapping pixel coordinates from a detector to world coordinates using a polynomial of order three. This method is used when working in sky coordinates and helps describe how the detector's physical structure affects where stars appear on the image.
SIP Formalism
The Spatial Interpolation Polynomial (SIP) formalism describes instrumental distortion directly within the focal plane, without needing a tangent-plane projection. This approach is used when modeling distortions in focal plane terms, offering an alternative way to characterize how the detector distorts the image.
Astrometric Residuals
Residual analysis measures positional differences between detected sources and their known reference positions. Key metrics like the average offset and standard deviation quantify calibration precision. A negligible average offset of within 2 mas confirms that the overall calibration is highly accurate.
Persistence Masking
This refers to a technique used to handle issues caused by detector persistence, which affects astrometric accuracy, especially in detectors DET13 and DET14. The paper developed a refined criterion based on persistence intensity and radius around detections to mitigate the negative impact of this effect.

Terminology

Summary

This paper presents the methodology and results of the astrometric calibration applied to the Euclid Near-Infrared (NIR) images in the Euclid Data Release 1, focusing on techniques used to model and correct instrumental distortions, as well as assessment of calibration quality The achieved accuracy is 30 mas for 97% of the total area, thus exceeding the requirements for Data Release 1

Calibration Methodology

The astrometric calibration pipeline relies on the Scamp software to compute the distortion and update associated keywords in the headers of the FITS frames This process utilizes either the PV formalism or a SIP formalism to model instrumental distortions, depending on whether it is working in sky coordinates or directly in focal plane terms The PV formalism maps pixel coordinates from that detector to intermediate world coordinates using a polynomial with order N = 3 In contrast, the SIP formalism describes the distortion directly in the focal plane without relying on a tangent-plane projection The relevant quantities are defined as px and py are the coordinates of the reference pixel, corresponding to the CRPIX keywords in the FITS files

Astrometric Residual Analysis

The analysis of astrometric residuals involves calculating several quantities derived from positional differences between N detections and their matched reference sources The average offset is given by the formula ⟨∆α∗⟩ = 1/N Σ i=1 ∆α∗i, ⟨∆δ⟩ = 1/N Σ i=1 ∆δi The standard deviation measures the spread of positional offsets around the mean, indicating calibration precision The RMS offset represents the total calibration accuracy (bias + precision) as RMS2 = RMS2α∗ + RMS2δ/2 Analysis of stacked catalogues confirms that the average offset to the reference catalogue is negligible, being within 2 mas

Geometric Distortion Verification

The paper verifies whether the geometric distortion is calibrated within 0.015% over scales of 3 arcmin This verification involves comparing pairs of stars separated by a distance dref between 2′5 and 3′5 in the Gaia DR3 catalogue with their corresponding separations in the NISP catalogues In all stacked catalogues examined here, the RMS of ν is less than 0. p. 6

Where the paper says it

015% over scales of 3′ , as in the requirement. To achieve this, for each stacked catalogue we extract within the matched sources the pairs separated by a distance dref between 2.

01% The analysis also evaluates how well the assumption of a constant presolution aligns with actual distortion observed in dithers

Mitigation Strategies and Future Work

A limitation identified in DR1 is the impact of persistence masking on astrometric accuracy, particularly affecting detectors DET13 and DET14 A mitigation strategy involving a refined persistence flagging criterion based on persistence intensity and radius around detections has been developed and applied in subsequent processing For future data releases, improvements include a refined persistence masking approach and exploration of alternative distortion evaluation methods that reduce the complexity of the distortion model while preserving the calibration quality A simplified distortion model with fewer free parameters would still allow for a reduction in computational complexity, but fitting only linear terms increases the residuals, necessitating a second-order polynomial fit to maintain comparable accuracy

Conclusion

The Euclid NISP astrometric calibration in DR1 demonstrates high precision and stability, with well-characterized residuals and identified pathways for further improvement The results provide a solid foundation for subsequent data releases, ensuring accurate celestial source positioning, which is essential for the mission’s scientific objectives

Acknowledgements

The Euclid Consortium acknowledges the European Space Agency and a number of agencies and institutes that have supported the development of Euclid This work has made use of the Euclid Data Release 1 (DR1) from the European Space Agency (ESA) mission Euclid This research makes use of ESA Datalabs (datalabs.esa.int), an initiative by ESA’s Data Science and Archives Division in the Science and Operations Department, Directorate of Science This work has made use of data from the European Space Agency (ESA) mission Gaia processed by the Gaia Data Processing and Analysis Consortium (DPAC, https://www. p. 2

Where the paper says it

Analysis of astrometric residuals We present a summary of the astrometric residuals generated by NIR_Astrometry, both in relation to the Gaia DR3 catalogue and internally among the dithers. To accomplish this, we select 4000 OBSID from the Euclid Wide Survey in the Science Archive System (SAS) for each NISP filter, covering an area of 1950 deg2 after removing overlaps (Sect.

cosmos.esa.int/web/gaia/dpac/consortium) Funding for the DPAC has been provided by national institutions, in particular the institutions participating in the Gaia Multilateral Agreement The Euclid Consortium acknowledges the European Space Agency and a number of agencies and institutes that have supported the development of Euclid, in particular the Agenzia Spaziale Italiana, the Austrian Forschungsförderungsgesellschaft funded through BMIMI, the Belgian Science Policy, the Canadian Euclid Consortium, the Deutsches Zentrum für Luft- und Raumfahrt, the DTU Space and the Niels Bohr Institute in Denmark A complete and detailed list is available on the Euclid web site (www.euclid-ec.org/consortium/community/) The Euclid Collaboration acknowledges M. p. 0
Where the paper says it

Astronomy & Astrophysics manuscript no. main ©ESO 2026 November 13, 2026 Euclid Data Release (DR1) NIR astrometric calibration Euclid Collaboration: M.

Radovich et al. p. 0
Where the paper says it

main ©ESO 2026 November 13, 2026 Euclid Data Release (DR1) NIR astrometric calibration Euclid Collaboration: M. Radovich, R.

: NIR astrometric calibration The paper has presented the methodology and results of the astrometric calibration applied to the NISP data in Euclid DR1

References

Bertin, E. 2006, in ASP Conference Series, Vol. p. 2

Where the paper says it

Consequently, NIR_Astrometry initially employs Scamp exclusively to adjust the CRVAL values, followed by an initial alignment utilising the Gaia DR3 catalogue through the presolution. Subsequently, a series of tests is conducted for each dither, to identify those for which it is not possible to derive a reliable astrometric solution.

p. 2
Where the paper says it

Consequently, NIR_Astrometry initially employs Scamp exclusively to adjust the CRVAL values, followed by an initial alignment utilising the Gaia DR3 catalogue through the presolution. Subsequently, a series of tests is conducted for each dither, to identify those for which it is not possible to derive a reliable astrometric solution.

p. 2
Where the paper says it

Consequently, NIR_Astrometry initially employs Scamp exclusively to adjust the CRVAL values, followed by an initial alignment utilising the Gaia DR3 catalogue through the presolution. Subsequently, a series of tests is conducted for each dither, to identify those for which it is not possible to derive a reliable astrometric solution.

p. 2
Where the paper says it

Consequently, NIR_Astrometry initially employs Scamp exclusively to adjust the CRVAL values, followed by an initial alignment utilising the Gaia DR3 catalogue through the presolution. Subsequently, a series of tests is conducted for each dither, to identify those for which it is not possible to derive a reliable astrometric solution.

p. 2
Where the paper says it

Consequently, NIR_Astrometry initially employs Scamp exclusively to adjust the CRVAL values, followed by an initial alignment utilising the Gaia DR3 catalogue through the presolution. Subsequently, a series of tests is conducted for each dither, to identify those for which it is not possible to derive a reliable astrometric solution.

p. 2
Where the paper says it

Consequently, NIR_Astrometry initially employs Scamp exclusively to adjust the CRVAL values, followed by an initial alignment utilising the Gaia DR3 catalogue through the presolution. Subsequently, a series of tests is conducted for each dither, to identify those for which it is not possible to derive a reliable astrometric solution.

p. 2
Where the paper says it

Consequently, NIR_Astrometry initially employs Scamp exclusively to adjust the CRVAL values, followed by an initial alignment utilising the Gaia DR3 catalogue through the presolution. Subsequently, a series of tests is conducted for each dither, to identify those for which it is not possible to derive a reliable astrometric solution.

p. 0
Where the paper says it

To support the use of the calibrated data products, for each parameter described in the text we also give the corresponding keyword in the NIR_AstrometricCalibration module of the NIR-PF (NIR_Astrometry hereafter). Astrometric calibration of NISP images in Euclid DR1 In the NIR-PF, NIR_Astrometry relies on the Scamp1 software (Bertin 2006) to compute the distortion and update the associated keywords in the headers of the FITS frames.

351, Astronomical Data Analysis Software and Systems XV, ed. p. 0
Where the paper says it

To support the use of the calibrated data products, for each parameter described in the text we also give the corresponding keyword in the NIR_AstrometricCalibration module of the NIR-PF (NIR_Astrometry hereafter). Astrometric calibration of NISP images in Euclid DR1 In the NIR-PF, NIR_Astrometry relies on the Scamp1 software (Bertin 2006) to compute the distortion and update the associated keywords in the headers of the FITS frames.

C. Gabriel, C. Arviset, D. Ponz, & S. Enrique, 112

Bertin, E. 2011, in Astronomical Society of the Pacific Conference Series, Vol. p. 1

Where the paper says it

The final Euclid calibrated positions are in the barycentric ICRS. Scamp processes the catalogues generated by SExtractor (Bertin & Arnouts 1996) in combination with PSFex (Bertin 2011), optimising the precision of source centres through pointspread function (PSF) fitting.

442, Astronomical Data Analysis Software and Systems XX, ed. p. 0
Where the paper says it

To support the use of the calibrated data products, for each parameter described in the text we also give the corresponding keyword in the NIR_AstrometricCalibration module of the NIR-PF (NIR_Astrometry hereafter). Astrometric calibration of NISP images in Euclid DR1 In the NIR-PF, NIR_Astrometry relies on the Scamp1 software (Bertin 2006) to compute the distortion and update the associated keywords in the headers of the FITS frames.

I. N. Evans, A. Accomazzi, D. J. Mink, & A. H. Rots, 435

Bertin, E.& Arnouts, S. p. 1

Where the paper says it

The final Euclid calibrated positions are in the barycentric ICRS. Scamp processes the catalogues generated by SExtractor (Bertin & Arnouts 1996) in combination with PSFex (Bertin 2011), optimising the precision of source centres through pointspread function (PSF) fitting.

, 1996., A&AS, 117, 393

Best, W. M. J., Liu, M. C., Magnier, E. A., & Dupuy, T. J. 2020., AJ, 159, 257

Calabretta, M. R.& Greisen, E. p. 1

Where the paper says it

Scamp utilises the PV formalism (see e. Calabretta & Greisen 2002; Shupe et al.

W., 2002., A&A, 395, 1077

Cox, C.& Gilliland, R. p. 6

Where the paper says it

Since the astrometric solution maps the observed pixel positions onto barycentric reference positions, this term is absorbed into the fitted plate scale s, which is then expected to vary by ∆s/s = v · nˆ /c (see e. Cox & Gilliland 2003).

L., 2003., in HST Calibration Workshop: Hubble after the Installation of the ACS and the NICMOS Cooling System, ed. p. 1
Where the paper says it

Distortion map showing the displacement (arcsec) on the focal plane in the R-mosaic coordinate system (Euclid Collaboration: Jahnke et al. 2025), as derived from a self-calibration observation.

S. Arribas, A. Koekemoer, & B. Whitmore, 58

Euclid Collaboration: da Silva, R., Faustini, F., Polenta, G. p. 0

Where the paper says it

da Silva, G. Polenta, A.

, et al., 2026., A&A, submitted

Euclid Collaboration: Jahnke, K., Gillard, W., Schirmer, M. p. 1

Where the paper says it

A&A proofs: manuscript no. main for each dither, because the combined effect of the tilt in the NISP optics (Euclid Collaboration: Schirmer et al.

, et al. 2025., A&A, 697, A3

Euclid Collaboration: Mellier, Y., Abdurro’uf, Acevedo Barroso, J., et al. 2025., A&A, 697, A1

Euclid Collaboration: Polenta, G., Frailis, M., Alavi, A., et al. 2026a., A&A, submitted

Euclid Collaboration: Polenta, G., Frailis, M., Alavi, A., et al. 2026b., A&A, 711, A3

Euclid Collaboration: Scaramella, R., Amiaux, J., Mellier, Y. p. 0

Where the paper says it

Cosmology: observations – Surveys – Astrometry – Techniques: image processing – Space vehicles: instruments – Instrumentation: detectors 1. Introduction Accurate astrometric calibration is essential for the success of the Euclid mission (Euclid Collaboration: Mellier et al.

, et al. 2022., A&A, 662, A1

Euclid Collaboration: Schirmer, M., Jahnke, K. p. 0

Where the paper says it

2023), and maintains internal consistency among multiple dithered images. Euclid’s Near-Infrared Spectrometer and Photometer (NISP: Euclid Collaboration: Jahnke et al.

, Seidel, G., et al. 2022., A&A, 662, A92

Euclid Collaboration: Schirmer, M., Paterson, K., Altieri, B., et al. 2026., A&A, submitted

Lindegren, L., Klioner, S. A., Hernández, J., et al. 2021., A&A, 649, A2

Shupe, D. L., Laher, R. R., Storrie-Lombardi, L., et al. 2012., in SPIE Conference Series, Vol. p. 2

Where the paper says it

Consequently, NIR_Astrometry initially employs Scamp exclusively to adjust the CRVAL values, followed by an initial alignment utilising the Gaia DR3 catalogue through the presolution. Subsequently, a series of tests is conducted for each dither, to identify those for which it is not possible to derive a reliable astrometric solution.

p. 2
Where the paper says it

Consequently, NIR_Astrometry initially employs Scamp exclusively to adjust the CRVAL values, followed by an initial alignment utilising the Gaia DR3 catalogue through the presolution. Subsequently, a series of tests is conducted for each dither, to identify those for which it is not possible to derive a reliable astrometric solution.

p. 2
Where the paper says it

Consequently, NIR_Astrometry initially employs Scamp exclusively to adjust the CRVAL values, followed by an initial alignment utilising the Gaia DR3 catalogue through the presolution. Subsequently, a series of tests is conducted for each dither, to identify those for which it is not possible to derive a reliable astrometric solution.

p. 2
Where the paper says it

Consequently, NIR_Astrometry initially employs Scamp exclusively to adjust the CRVAL values, followed by an initial alignment utilising the Gaia DR3 catalogue through the presolution. Subsequently, a series of tests is conducted for each dither, to identify those for which it is not possible to derive a reliable astrometric solution.

p. 2
Where the paper says it

Consequently, NIR_Astrometry initially employs Scamp exclusively to adjust the CRVAL values, followed by an initial alignment utilising the Gaia DR3 catalogue through the presolution. Subsequently, a series of tests is conducted for each dither, to identify those for which it is not possible to derive a reliable astrometric solution.

p. 2
Where the paper says it

Consequently, NIR_Astrometry initially employs Scamp exclusively to adjust the CRVAL values, followed by an initial alignment utilising the Gaia DR3 catalogue through the presolution. Subsequently, a series of tests is conducted for each dither, to identify those for which it is not possible to derive a reliable astrometric solution.

p. 2
Where the paper says it

Consequently, NIR_Astrometry initially employs Scamp exclusively to adjust the CRVAL values, followed by an initial alignment utilising the Gaia DR3 catalogue through the presolution. Subsequently, a series of tests is conducted for each dither, to identify those for which it is not possible to derive a reliable astrometric solution.

8451, Software and Cyberinfrastructure for Astronomy II, ed. p. 0
Where the paper says it

Astronomy & Astrophysics manuscript no. main ©ESO 2026 November 13, 2026 Euclid Data Release (DR1) NIR astrometric calibration Euclid Collaboration: M.

p. 0
Where the paper says it

Astronomy & Astrophysics manuscript no. main ©ESO 2026 November 13, 2026 Euclid Data Release (DR1) NIR astrometric calibration Euclid Collaboration: M.

p. 0
Where the paper says it

Astronomy & Astrophysics manuscript no. main ©ESO 2026 November 13, 2026 Euclid Data Release (DR1) NIR astrometric calibration Euclid Collaboration: M.

p. 0
Where the paper says it

Astronomy & Astrophysics manuscript no. main ©ESO 2026 November 13, 2026 Euclid Data Release (DR1) NIR astrometric calibration Euclid Collaboration: M.

p. 0
Where the paper says it

Astronomy & Astrophysics manuscript no. main ©ESO 2026 November 13, 2026 Euclid Data Release (DR1) NIR astrometric calibration Euclid Collaboration: M.

p. 0
Where the paper says it

Astronomy & Astrophysics manuscript no. main ©ESO 2026 November 13, 2026 Euclid Data Release (DR1) NIR astrometric calibration Euclid Collaboration: M.

p. 0
Where the paper says it

Astronomy & Astrophysics manuscript no. main ©ESO 2026 November 13, 2026 Euclid Data Release (DR1) NIR astrometric calibration Euclid Collaboration: M.

N. M. Radziwill & G. Chiozzi, 84511M

Shupe, D. L., Moshir, M., Li, J., et al. 2005., in ASP Conference Series, Vol. 347, Astronomical Data Analysis Software and Systems XIV, ed. p. 0

Where the paper says it

To support the use of the calibrated data products, for each parameter described in the text we also give the corresponding keyword in the NIR_AstrometricCalibration module of the NIR-PF (NIR_Astrometry hereafter). Astrometric calibration of NISP images in Euclid DR1 In the NIR-PF, NIR_Astrometry relies on the Scamp1 software (Bertin 2006) to compute the distortion and update the associated keywords in the headers of the FITS frames.

p. 0
Where the paper says it

To support the use of the calibrated data products, for each parameter described in the text we also give the corresponding keyword in the NIR_AstrometricCalibration module of the NIR-PF (NIR_Astrometry hereafter). Astrometric calibration of NISP images in Euclid DR1 In the NIR-PF, NIR_Astrometry relies on the Scamp1 software (Bertin 2006) to compute the distortion and update the associated keywords in the headers of the FITS frames.

p. 0
Where the paper says it

To support the use of the calibrated data products, for each parameter described in the text we also give the corresponding keyword in the NIR_AstrometricCalibration module of the NIR-PF (NIR_Astrometry hereafter). Astrometric calibration of NISP images in Euclid DR1 In the NIR-PF, NIR_Astrometry relies on the Scamp1 software (Bertin 2006) to compute the distortion and update the associated keywords in the headers of the FITS frames.

p. 0
Where the paper says it

To support the use of the calibrated data products, for each parameter described in the text we also give the corresponding keyword in the NIR_AstrometricCalibration module of the NIR-PF (NIR_Astrometry hereafter). Astrometric calibration of NISP images in Euclid DR1 In the NIR-PF, NIR_Astrometry relies on the Scamp1 software (Bertin 2006) to compute the distortion and update the associated keywords in the headers of the FITS frames.

p. 0
Where the paper says it

To support the use of the calibrated data products, for each parameter described in the text we also give the corresponding keyword in the NIR_AstrometricCalibration module of the NIR-PF (NIR_Astrometry hereafter). Astrometric calibration of NISP images in Euclid DR1 In the NIR-PF, NIR_Astrometry relies on the Scamp1 software (Bertin 2006) to compute the distortion and update the associated keywords in the headers of the FITS frames.

p. 0
Where the paper says it

To support the use of the calibrated data products, for each parameter described in the text we also give the corresponding keyword in the NIR_AstrometricCalibration module of the NIR-PF (NIR_Astrometry hereafter). Astrometric calibration of NISP images in Euclid DR1 In the NIR-PF, NIR_Astrometry relies on the Scamp1 software (Bertin 2006) to compute the distortion and update the associated keywords in the headers of the FITS frames.

P. Shopbell, M. Britton, & R. Ebert, 491

Vallenari, A., Brown, A. G. A., Prusti, T. p. 1

Where the paper says it

(2) In this case, because the distortion is expressed purely in focal plane terms, it does not depend on the telescope rotation. In DR1, the adopted external reference is the Gaia DR3 catalogue (Gaia Collaboration: Prusti et al.

p. 1
Where the paper says it

(2) In this case, because the distortion is expressed purely in focal plane terms, it does not depend on the telescope rotation. In DR1, the adopted external reference is the Gaia DR3 catalogue (Gaia Collaboration: Prusti et al.

p. 1
Where the paper says it

(2) In this case, because the distortion is expressed purely in focal plane terms, it does not depend on the telescope rotation. In DR1, the adopted external reference is the Gaia DR3 catalogue (Gaia Collaboration: Prusti et al.

p. 1
Where the paper says it

(2) In this case, because the distortion is expressed purely in focal plane terms, it does not depend on the telescope rotation. In DR1, the adopted external reference is the Gaia DR3 catalogue (Gaia Collaboration: Prusti et al.

p. 1
Where the paper says it

(2) In this case, because the distortion is expressed purely in focal plane terms, it does not depend on the telescope rotation. In DR1, the adopted external reference is the Gaia DR3 catalogue (Gaia Collaboration: Prusti et al.

p. 1
Where the paper says it

(2) In this case, because the distortion is expressed purely in focal plane terms, it does not depend on the telescope rotation. In DR1, the adopted external reference is the Gaia DR3 catalogue (Gaia Collaboration: Prusti et al.

p. 1
Where the paper says it

(2) In this case, because the distortion is expressed purely in focal plane terms, it does not depend on the telescope rotation. In DR1, the adopted external reference is the Gaia DR3 catalogue (Gaia Collaboration: Prusti et al.

p. 1
Where the paper says it

(2) In this case, because the distortion is expressed purely in focal plane terms, it does not depend on the telescope rotation. In DR1, the adopted external reference is the Gaia DR3 catalogue (Gaia Collaboration: Prusti et al.

p. 1
Where the paper says it

(2) In this case, because the distortion is expressed purely in focal plane terms, it does not depend on the telescope rotation. In DR1, the adopted external reference is the Gaia DR3 catalogue (Gaia Collaboration: Prusti et al.

p. 1
Where the paper says it

(2) In this case, because the distortion is expressed purely in focal plane terms, it does not depend on the telescope rotation. In DR1, the adopted external reference is the Gaia DR3 catalogue (Gaia Collaboration: Prusti et al.

p. 1
Where the paper says it

(2) In this case, because the distortion is expressed purely in focal plane terms, it does not depend on the telescope rotation. In DR1, the adopted external reference is the Gaia DR3 catalogue (Gaia Collaboration: Prusti et al.

p. 1
Where the paper says it

(2) In this case, because the distortion is expressed purely in focal plane terms, it does not depend on the telescope rotation. In DR1, the adopted external reference is the Gaia DR3 catalogue (Gaia Collaboration: Prusti et al.

, et al. 2023., A&A, 674, A1

Euclid Data Release 1. 2026., https://doi.org/10.57780/esa-d079c51

Gaia Collaboration: Prusti, T., de Bruijne, J. H. J., Brown, A. G. A., et al. 2016., A&A, 595, A1

Gaia Collaboration: Vallenari, A., Brown, A. G. A., Prusti, T., et al. 2023., A&A, 674, A1

Lindegren, L., Klioner, S. A., Hernández, J., et al. 2021., A&A, 649, A2

Shupe, D. L., Laher, R. R., Storrie-Lombardi, L., et al. 2012., in SPIE Conference Series, Vol. 8451, Software and Cyberinfrastructure for Astronomy II, ed. N. M. Radziwill & G. Chiozzi, 84511M

Shupe, D. L., Moshir, M., Li, J., et al. 2005., in ASP Conference Series, Vol. 347, Astronomical Data Analysis Software and Systems XIV, ed. P. Shopbell, M. Britton, & R. Ebert, 491

Vallenari, A., Brown, A. G. A., Prusti, T., et al. 2023., A&A, 674, A1

Euclid Data Release 1. 2026., https://doi.org/10.57780/esa-d079c51

Gaia Collaboration: Prusti, T., de Bruijne, J. H. J., Brown, A. G. A., et al. 2016., A&A, 595, A1

Gaia Collaboration: Vallenari, A., Brown, A. G. A., Prusti, T., et al. 2023., A&A, 674, A1

Lindegren, L., Klioner, S. A., Hernández, J., et al. 2021., A&A, 649, A2

Shupe, D. L., Laher, R. R., Storrie-Lombardi, L., et al. 2012., in SPIE Conference Series, Vol. 8451, Software and Cyberinfrastructure for Astronomy II, ed. N. M. Radziwill & G. Chiozzi, 84511M

Shupe, D. L., Moshir, M., Li, J., et al. 2005., in ASP Conference Series, Vol. 347, Astronomical Data Analysis Software and Systems XIV, ed. P. Shopbell, M. Britton, & R. Ebert, 491

Vallenari, A., Brown, A. G. A., Prusti, T., et al. 2023., A&A, 674, A1

Euclid Data Release 1. 2026., https://doi.org/10.57780/esa-d079c51

Gaia Collaboration: Prusti, T., de Bruijne, J. H. J., Brown, A. G. A., et al. 2016., A&A, 595, A1

Gaia Collaboration: Vallenari, A., Brown, A. G. A., Prusti, T., et al. 2023., A&A, 674, A1

Lindegren, L., Klioner, S. A., Hernández, J., et al. 2021., A&A, 649, A2

Shupe, D. L., Laher, R. R., Storrie-Lombardi, L., et al. 2012., in SPIE Conference Series, Vol. 8451, Software and Cyberinfrastructure for Astronomy II, ed. N. M. Radziwill & G. Chiozzi, 84511M

Shupe, D. L., Moshir, M., Li, J., et al. 2005., in ASP Conference Series, Vol. 347, Astronomical Data Analysis Software and Systems XIV, ed. P. Shopbell, M. Britton, & R. Ebert, 491

Vallenari, A., Brown, A. G. A., Prusti, T., et al. 2023., A&A, 674, A1

Euclid Data Release 1. 2026., https://doi.org/10.57780/esa-d079c51

Gaia Collaboration: Prusti, T., de Bruijne, J. H. J., Brown, A. G. A., et al. 2016., A&A, 595, A1

Gaia Collaboration: Vallenari, A., Brown, A. G. A., Prusti, T., et al. 2023., A&A, 674, A1

Lindegren, L., Klioner, S. A., Hernández, J., et al. 2021., A&A, 649, A2

Shupe, D. L., Laher, R. R., Storrie-Lombardi, L., et al. 2012., in SPIE Conference Series, Vol. 8451, Software and Cyberinfrastructure for Astronomy II, ed. N. M. Radziwill & G. Chiozzi, 84511M

Shupe, D. L., Moshir, M., Li, J., et al. 2005., in ASP Conference Series, Vol. 347, Astronomical Data Analysis Software and Systems XIV, ed. P. Shopbell, M. Britton, & R. Ebert, 491

Vallenari, A., Brown, A. G. A., Prusti, T., et al. 2023., A&A, 674, A1

Euclid Data Release 1. 2026., https://doi.org/10.57780/esa-d079c51

Gaia Collaboration: Prusti, T., de Bruijne, J. H. J., Brown, A. G. A., et al. 2016., A&A, 595, A1

Gaia Collaboration: Vallenari, A., Brown, A. G. A., Prusti, T., et al. 2023., A&A, 674, A1

Lindegren, L., Klioner, S. A., Hernández, J., et al. 2021., A&A, 649, A2

Shupe, D. L., Laher, R. R., Storrie-Lombardi, L., et al. 2012., in SPIE Conference Series, Vol. 8451, Software and Cyberinfrastructure for Astronomy II, ed. N. M. Radziwill & G. Chiozzi, 84511M

Shupe, D. L., Moshir, M., Li, J., et al. 2005., in ASP Conference Series, Vol. 347, Astronomical Data Analysis Software and Systems XIV, ed. P. Shopbell, M. Britton, & R. Ebert, 491

Vallenari, A., Brown, A. G. A., Prusti, T., et al. 2023., A&A, 674, A1

Euclid Data Release 1. 2026., https://doi.org/10.57780/esa-d079c51

Gaia Collaboration: Prusti, T., de Bruijne, J. H. J., Brown, A. G. A., et al. 2016., A&A, 595, A1

Gaia Collaboration: Vallenari, A., Brown, A. G. A., Prusti, T., et al. 2023., A&A, 674, A1

Lindegren, L., Klioner, S. A., Hernández, J., et al. 2021., A&A, 649, A2

Shupe, D. L., Laher, R. R., Storrie-Lombardi, L., et al. 2012., in SPIE Conference Series, Vol. 8451, Software and Cyberinfrastructure for Astronomy II, ed. N. M. Radziwill & G. Chiozzi, 84511M

Shupe, D. L., Moshir, M., Li, J., et al. 2005., in ASP Conference Series, Vol.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved distortion modeling by incorporating a second-order polynomial fit into simplified distortion models to reduce computational complexity while maintaining calibration accuracy comparable to full polynomial models. This allows for a more efficient pipeline that still captures residual variations in instrument behavior.

  2. Enhanced persistence masking strategy by discarding pixels only when the pixels within a defined radius Rp from the detection centre exceed a specified persistence threshold Ip, rather than using a fixed threshold on all pixels in the persistence image. This mitigates the reduction in source matches while preserving more accurate astrometric calibration.

  3. Implementation of an iterative 3 sigma clipping approach across focal plane cells and one-dimensional strips to compute mean offsets and standard deviations, ensuring robust spatial mapping of residuals even when dealing with varying source densities and noise levels. This provides a more stable estimation of the geometric distortion parameters across the entire field of view.

  4. Advanced parallax recovery using a least squares fit to determine the relationship between NISP and Gaia DR3 parallaxes, allowing for precise determination of zero-point offsets without biasing probe star measurements low by a consistent amount. This preserves the full amplitude of the stellar parallax signal in both JE and HE bands.

  5. Development of a simplified distortion model that applies a constant presolution followed only by fitting linear terms specific to each dither, with empirical validation showing that this approach increases residuals compared to the full polynomial fit, thus guiding future model complexity decisions. This helps balance computational savings against necessary calibration precision.

Abstract

This paper presents the methodology and results of the astrometric calibration applied to the Euclid Near-Infrared (NIR) images in the Euclid Data Release 1, focusing on the techniques used to model and correct instrumental distortions, as well as the assessment of calibration quality. This work details the calibration pipeline, including quality control tests, and the evaluation of astrometric residuals against the Gaia DR3 catalogue and internal consistency metrics based on data encompassing more than one year of Euclid operation: the achieved accuracy is 30 mas for 97% of the total area, thus exceeding the requirements for Data Release 1. For the remaining 3%, accuracy declines due to a persistence correction issue: a method to correct the issue is presented. Furthermore, we discuss the stability of the solution over time, its dependence on source properties and instrument configuration, and outline the improvements planned for future Euclid data releases to enhance the astrometric calibration accuracy and efficiency.

Related papers