Low-Cost Streetlight Shields for Dark-Sky Protection at a Stargazing Camp

arXiv:2611.15163 · astro-ph.IM · Submitted 2026-11-11 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Astrophysics. The day in astrophysics: observations, models and what the data forces.

Vera: We're looking at the paper: "Low-Cost Streetlight Shields for Dark-Sky Protection at a Stargazing Camp".

Jocelyn: Here's the gist of the paper. Road lighting at stargazing camps can cause glare and stray light that interfere with observationDirectional shields provide a relatively low-cost way to reduce unwanted light while retaining the existing road-lighting system.

Vera: Study Setup and Methodology The study involved installing directional shields on existing solar-powered streetlights at Bayan Gol Starlight Camp in Inner Mongolia, China.

Jocelyn: The shields were designed as a curved directional shield printed in black PETG, fitting the lamp housing and its existing mounting points.

Vera: Measurements were taken before and after installation on July 14 and July 15, 2026.

Title and authors: Vera: So we're looking at this paper today titled "Low-Cost Streetlight Shields for Dark-Sky Protection at a Stargazing Camp" by Liu, Ding, and Zhang. It’s about using existing streetlights to reduce glare for stargazing.

Jocelyn: Yeah, it tackles that problem directly. The authors installed these directional shields on solar-powered lights in Inner Mongolia to see what happens to the sky brightness when you block the light coming from those lamps.

Subrahmanyan: From a cosmology perspective, this is interesting because it deals with local light pollution and how much it affects our ability to see faint objects, which is always a factor in structure formation studies.

Vera: Exactly. The core idea here is that road lighting at these camps causes glare and stray light that messes with observations, so they put directional shields on the existing lamps to reduce that unwanted light while keeping the original system intact.

Jocelyn: They used these curved directional shields printed in black PETG, which they designed to fit over the lamp housing and its mounting points. They measured before and after installation at two spots: P1, right in the camp center, and P2 about five hundred meters away.

Subrahmanyan: I wonder how much of a real impact this kind of localized intervention has on the overall light budget we model for deep-sky surveys.

Vera: The study quantified the light reduction by measuring sky brightness using an SQM L meter at elevations of zero, thirty, sixty, and ninety degrees. They measured at P1 and P2 to see how it affected different viewing angles.

Jocelyn: They found significant reductions in the equivalent SQM signal within the measured fields of view. Specifically at P2 toward the camp at a zero-degree elevation, the mean SQM reading increased by two point three one two mag arcsec minus two, which is about an eighty eight point one percent decrease in that viewing field.

Subrahmanyan: Eighty-eight percent is a substantial reduction for localized light sources; I’m curious if that kind of attenuation scales well across larger areas when considering the density of light sources in a camp setting.

Vera: The results showed that the most pronounced improvements were definitely in horizontal and low-elevation fields. The largest post-retrofit difference was concentrated in the horizontal view toward the camp, which makes sense because the shield geometry reduces visibility from those directions.

Jocelyn: The authors explained that this concentration of response at low elevations happens because the upper and side panels of the shield reduce the area of that light source visible to observers looking horizontally or obliquely.

Subrahmanyan: It sounds like a specific geometric constraint is dictating where the attenuation is strongest, which means we need to be very precise about defining those viewing angles when we model these effects theoretically.

Vera: The practical implication for us as astronomers and facility managers is that this retrofit offers a workflow for existing lighting systems by fitting shields onto lamps without having to replace the fixtures or mess with the electrical system.

Jocelyn: It’s presented as a relatively low-cost option to improve the nighttime light environment at smaller stargazing sites, which is really something for practical applications.

Subrahmanyan: It's an interesting approach because it suggests that evaluations of stargazing facilities shouldn't just rely on central or zenith measurements, but should include places where visitors are actually going to observe.

Vera: The study highlights a limitation they had to address: the before-and-after measurements were obtained on different nights, which could potentially alter the actual nighttime brightness.

Jocelyn: To fix that, the authors suggest future work needs to cover several comparable moonless nights and record atmospheric conditions like cloud cover and humidity for a more direct comparison of those results.

Subrahmanyan: And from a theoretical standpoint, they also noted that expanding the spatial sampling would be important to define how this light reduction response decreases with distance by placing sites along comparable sightlines at increasing distances.

Vera: Long-term monitoring is also suggested to evaluate material durability under UV exposure and temperature cycling, which is something we always have to consider when deploying hardware outdoors.

Jocelyn: So, to wrap up this paper on "Low-Cost Streetlight Shields for Dark-Sky Protection at a Stargazing Camp," the main point is that directional shielding can change the light entering selected viewing fields while keeping the original lamps in place.

Subrahmanyan: It provides a relatively low-cost and practical way to protect dark skies at these sites, and the largest changes were concentrated in low-elevation views and varied by direction.

Vera: The key takeaway is that directional shields can be evaluated as retrofits at stargazing sites using fixed viewing directions.

Jocelyn: But we need those repeated measurements under comparable conditions to really trust those numbers.

Subrahmanyan: It’s a practical tool, but the comparison covered only two nights, so repeated measurements under comparable conditions are needed before we can draw stronger conclusions about its effectiveness in real-world scenarios.

The paper's summary: Vera: So, we're looking at these directional shields on existing streetlights to cut down on glare for stargazing camps. This paper basically shows how you can use stuff that already exists to make a better dark sky environment without having to buy new lights or rewire anything.

Jocelyn: Right, it’s about fitting these curved PETG shields onto standard solar lamps and seeing how much they actually reduce the unwanted light hitting your telescope. They measured the sky brightness in different directions, from straight up down to horizontal views.

Subrahmanyan: From a cosmological angle, this is interesting because we often talk about light pollution as a way that local sources drown out the fainter signals we're looking for in deep space. This work shows a very low-cost way to fight it right where people are actually observing.

Vera: Exactly. The study found that at the spot five hundred meters away, looking toward the camp at zero degrees elevation, they saw an improvement of about eighty eight point one percent in the measured signal. That’s a solid number for how much light they managed to block out using this simple design.

Jocelyn: It really highlights that these improvements are most noticeable in those horizontal and low-elevation views, which makes sense because the shield is designed to block light coming from those specific directions. The geometry of the shield itself dictates where it’s working best.

Subrahmanyan: That geometric explanation is key for us theorists; it tells us exactly what kind of spatial sampling we need to do when we model these effects across a whole field, because the response changes depending on the angle you are looking at.

Vera: And the practical side is pretty compelling because it's a retrofit solution. You don't replace your fixtures or mess with the electrical system; you just fit these shields onto them. It’s a way to improve conditions right now, cheaply.

Jocelyn: It makes sense that they suggest this approach should be considered when we evaluate stargazing sites, because they aren't just looking at what's happening right overhead or dead center anymore. They need to look where the visitors are actually pointing their telescopes.

Subrahmanyan: I agree with that, but I gotta bring up the limitations they flagged. They did their before and after measurements on two different nights, which means those results might be skewed by natural variations in moonlight or cloud cover, so you can't just take those numbers as absolute truth yet.

Vera: That’s a fair point about the comparison. They need to do more testing under comparable conditions—like several moonless nights and recording things like humidity—before we can fully trust the quantified reduction in sky brightness across all those different viewing angles.

Jocelyn: So, it's a nice proof of concept showing that localized shielding works, but for any serious application, we need to get those measurements locked down with better control over the environmental variables. This leads us into how we can better handle instrumental noise in observations...

The paper's improvements: Tom: So, we're looking at how the authors suggest making these directional shields even better for real use. They aren't just showing one setup; they’re talking about refining the whole process.

Vera: Exactly. The paper points out that while the basic shield works, you need a real workflow for fitting them onto lamps without touching the wiring or replacing the fixture itself. It’s about making it a practical step for anyone managing existing lighting systems.

Jocelyn: And they emphasize that because they focused on low-elevation views, you should specifically evaluate those viewing directions when testing these shields at a site. You can't just check zenith and assume everything is fine.

Subrahmanyan: That makes sense from a modeling standpoint; the geometry of the shield means its effectiveness is highly dependent on the observation direction, so you need to define those fixed viewing angles precisely when you run your simulations.

Vera: They also stress that for real-world deployment, long-term monitoring is necessary. You need to check how that PETG material holds up over time when it's exposed to UV light and temperature changes outside the lab.

Jocelyn: It’s about durability, right? Because if the shield degrades quickly in the elements, all that initial light reduction benefit just disappears over a few seasons. That’s a crucial caveat for any hardware deployment.

Subrahmanyan: From a structural perspective, they also suggest expanding how you sample space when you look at distance. You need to place those observation points along similar sightlines at increasing distances to see how the response changes as you move away from the light source.

Vera: So it’s about making the testing method more robust by adding these layers—workflow, directionality, and long-term material checks—so it moves from a simple experiment to a usable tool.

Jocelyn: It sounds like they are pushing for standardized testing protocols so that when astronomers or facility managers look at this kind of solution, they know exactly what kind of data to expect and what caveats to watch out for. That standardization is huge.

Subrahmanyan: If we can get better control over these systematic errors introduced by the shielding itself, it helps us isolate the true effect of the light pollution from other instrumental noise in our deep sky observations.

Vera: Right, so this isn't just about blocking light; it's about creating a more reliable and predictable system for managing light at observing sites. It moves beyond just showing a good result to suggesting how to actually put that result into practice safely.

Jocelyn: And that’s where we go from just seeing a paper to thinking about how these small engineering fixes impact the quality of astronomical data we collect in the future.

Conclusion: Tom: So, to wrap this up, we're talking about these low-cost streetlight shields for dark-sky protection at stargazing camps. The main idea is that you can use existing streetlights to block glare without replacing the whole system or adding electrical wiring.

Vera: Right. It’s a practical demonstration of how localized shielding can immediately improve the viewing experience at a site, and it shows that evaluations shouldn't just look at the center of the camp but where people are actually looking.

Jocelyn: I agree with that; it shifts the focus from just measuring light in space to understanding light in human observation. It’s about making sure our local environment doesn't interfere with what we’re trying to measure, whether it's stars or pulsars.

Subrahmanyan: It confirms that even small interventions can have measurable effects on the overall sky brightness budget near a structure, which is relevant when we look at how local sources affect faint signals in structure formation studies.

Vera: The caveat remains that you need those repeated measurements under comparable conditions to truly validate the eighty eight point one percent reduction they found. That’s the practical hurdle for us as observers.

Jocelyn: We have to be careful not to take those numbers too seriously until they are tested across different nights and atmospheric states, otherwise we risk misinterpreting what the shield actually does under variable conditions.

Subrahmanyan: If these types of localized light reductions are real, it might open up new ways for us to model how light pollution affects cosmological surveys if we can accurately account for these local sources in our data reduction pipelines.

Vera: So, the conclusion is that directional shielding is a low-cost retrofit option that works best in low-elevation views and by direction, but we need better environmental control before we call it a universal solution.

Jocelyn: It’s a good summary of the paper on "Low-Cost Streetlight Shields for Dark-Sky Protection at a Stargazing Camp." It shows us that engineering solutions can have very direct, tangible impacts on observational science.

Subrahmanyan: And while it's not a solution to all cosmic problems, it’s an excellent example of how we can apply targeted optical design principles to improve local observational constraints.

Vera: Exactly. We’ve seen how these simple geometric changes can yield measurable data points that help us understand the practical limitations of existing infrastructure in astronomical settings.

Jocelyn: Next time, we'll be looking at something completely different, diving into a new paper on automated photometric pipelines for survey-era astronomy.

Xiaoyong Liu, Ruobin Ding, Sixuan Zhang

Experimental High School Attached to Beijing Normal University · School of Physics and Astronomy, Beijing Normal University · Hiroshima Astrophysical Science Center, Hiroshima University

astro-ph.IM

Submitted: 2026-11-11

Updated: 2026-11-11

Comments: 10 pages, 7 figures

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 72/100

The gist: Road lighting at stargazing camps can cause glare and stray light that interfere with observationDirectional shields provide a relatively low-cost way to reduce unwanted light while retaining the…

Key concepts

Directional Shields
These are curved panels printed in black PETG designed to fit around existing streetlights. They function by blocking unwanted light from specific angles, reducing glare for observers while keeping the original lamp system intact.
Equivalent SQM Signal
This is a measurement used to quantify the brightness of the sky as seen through a specific viewing angle. A lower signal value indicates less unwanted light interference, which is what researchers measured before and after installing the shields.
Low-Elevation Views
These are viewing angles close to the horizon, where road lighting often causes the most significant glare. The study found that directional shields provided their greatest effectiveness in these low-elevation fields because their design blocks light coming from horizontal and oblique directions.

Terminology

Summary

Road lighting at stargazing camps can cause glare and stray light that interfere with observationDirectional shields provide a relatively low-cost way to reduce unwanted light while retaining the existing road-lighting system. p. 0

Where the paper says it

Directional shields provide a relatively low-cost way to reduce unwanted light while retaining the existing road-lighting system. Keywords: Light pollution;Dark-sky protection; Outdoor lamp shade; SQM-L; Stargazing camp; Obtrusive light 1 Introduction Artificial light scattered by the atmosphere creates skyglow and makes faint stars harder to see.

Study Setup and Methodology

The study involved installing directional shields on existing solar-powered streetlights at Bayan Gol Starlight Camp in Inner Mongolia, China. The shields were designed as a curved directional shield printed in black PETG, fitting the lamp housing and its existing mounting points. p. 1

Where the paper says it

We designed a curved directional shield to fit the lamp housing and its existing mounting points. The directional shield was printed in black PETG.

Measurements were taken before and after installation on July 14 and July 15, 2026. p. 1
Where the paper says it

The directional shield was attached at the original mounting location. 2 SQM Measurements and Photographs We took pre-retrofit SQM-L measurements on 14 July 2026 and post-retrofit measurements on 15 July 2026, after installing the directional shields.

The SQM-L meter was used to measure sky brightness at elevations of 0, 30, 60, and 90 degrees. p. 1
Where the paper says it

We used a Unihedron SQM-L sky brightness meter. The SQM-L has an angular response with a full width at half maximum of about 20 degrees and reports readings in magnitudes per square arcsecond (Cinzano 2005).

Measurements were conducted at P1 in the camp center and P2 approximately 500 m away. p. 0
Where the paper says it

cn 3 Hiroshima Astrophysical Science Center, Hiroshima University, 1-3-1 Kagamiyama, Higashi-Hiroshima, Hiroshima 739-8526 Japan Abstract Road lighting at stargazing camps can cause glare and stray light that interfere with observation. We installed directional shields on existing solar-powered streetlights at Bayan Gol Starlight Camp in Inner Mongolia, China, and compared SQM-L measurements before and after installation at the camp center (P1) and a site approximately 500 m away (P2).

Quantified Light Reduction

The installation resulted in significant reductions in the equivalent SQM signal within the measured fields of view. Specifically, at P2 toward the camp at a 0-degree elevation, the mean SQM reading increased by 2. p. 0

Where the paper says it

At 0 ◦ , the mean SQM reading across four directions at P1 increased by 1. 624 mag arcsec−2 , and the reading toward the camp at P2 increased by 2.

312 mag arcsec−2, corresponding to an approximately 88. p. 0
Where the paper says it

312 mag arcsec−2 . These changes correspond to reductions of approximately 77.

1% decrease in the equivalent SQM signal within that viewing field. p. 5
Where the paper says it

Equation (3) converts this value to an approximately 88. 1% decrease in the equivalent SQM signal within that viewing field.

The largest changes were concentrated in low-elevation views. p. 0
Where the paper says it

Photographs taken with identical exposure settings showed less visible glare around the shielded lamps. The measurements indicate that the changes were concentrated in low-elevation views.

Directional Sensitivity of Results

The results demonstrated that the most pronounced improvements occurred in horizontal and low-elevation fields. At P2, the largest post-retrofit difference was confined to the horizontal view toward the camp. p. 6

Where the paper says it

The four lines in Figure 7 meet at this common 90◦ value because the zenith was represented by one shared reading rather than four direction-specific measurements. Across the P2 measurements, the largest post-retrofit difference was therefore confined to the horizontal view toward the camp.

The shield geometry explains this concentration of response at low elevations because its upper and side panels reduce the area of the emitting surface visible from horizontal and oblique directions. p. 7
Where the paper says it

2 Interpretation of the directional changes The shield geometry helps explain the concentration of the response at low elevations. Its upper and side panels reduce the area of the emitting surface visible from horizontal and oblique directions, while the open underside preserves downward illumination.

Practical Implications for Lighting

The retrofit offers a practical workflow for existing lighting systems by fitting shields to lamps without replacing fixtures or modifying the electrical system. This approach is consistent with guidance to limit obtrusive and spill light, providing a low-cost option for improving the nighttime light environment at small stargazing sites. p. 0

Where the paper says it

It therefore provides a relatively low-cost option for improving the nighttime light environment at small stargazing sites. This approach is consistent with guidance to limit obtrusive and spill light (Gaston et al.

The study suggests that evaluations of stargazing facilities should include places where visitors may actually observe, rather than relying only on central or zenith measurements. p. 6
Where the paper says it

The response at P2 shows that the effect of a local retrofit can be relevant beyond the installation site itself. It also shows why evaluations of stargazing facilities should include the places where visitors may actually observe, rather than relying only on a central or zenith measurement.

Limitations and Future Work

A main experimental limitation is that the before-and-after measurements were obtained on different nights, which could alter nighttime brightness. Future work should cover several comparable moonless nights and record atmospheric conditions like cloud cover and humidity for a more direct comparison. p. 7

Where the paper says it

Future measurements should cover several comparable moonless nights and record cloud cover, visibility, humidity, wind, measurement time, and temporary light sources. If the installation can be changed safely, alternating shielded and unshielded states during the same night would provide a more direct comparison.

Additionally, spatial sampling should be expanded to define how the response decreases with distance by placing sites along comparable sightlines at increasing distances. p. 7
Where the paper says it

One outside site is sufficient to show that a camp-facing change was detectable at that location, but it cannot define how the response decreases with distance. Several outside sites should be placed along comparable sightlines at increasing distances, with foreground obstructions documented at each position.

Long-term monitoring should also evaluate material durability under UV exposure and temperature cycling. p. 7
Where the paper says it

Road illuminance, pedestrian-level vertical illuminance, and glare should be measured before and after shielding. Long-term monitoring should also record deformation, discoloration, cracking, loose fasteners, and dust accumulation on the PETG shields under ultraviolet exposure, temperature cycling, wind, and precipitation.

Conclusion

Directional shielding can change light entering selected viewing fields while retaining existing lamps. Because the retrofit retains the existing lamps and electrical systems, it provides a relatively low-cost and practical approach to dark-sky protection at stargazing sites. p. 8

Where the paper says it

Directional shields can be evaluated as retrofits at stargazing sites using fixed viewing directions. p. 8

Where the paper says it

Because the comparison covered two nights, repeated measurements under comparable conditions are needed. Directional shields can be evaluated as retrofits at stargazing sites using fixed viewing directions.

p. 8
Where the paper says it

Because the comparison covered two nights, repeated measurements under comparable conditions are needed. Directional shields can be evaluated as retrofits at stargazing sites using fixed viewing directions.

Because the retrofit retains the existing lamps and electrical systems, it also provides a relatively low-cost and practical approach to dark-sky protection at stargazing sites.

The largest changes occurred in low-elevation views and varied by direction. p. 8
Where the paper says it

1% decrease in the equivalent SQM signal within that field. The largest changes occurred in low-elevation views and varied by direction.

p. 8
Where the paper says it

1% decrease in the equivalent SQM signal within that field. The largest changes occurred in low-elevation views and varied by direction.

Directional shields can be evaluated as retrofits at stargazing sites using fixed viewing directions. The comparison covered two nights, repeated measurements under comparable conditions are needed. p. 8
Where the paper says it

They apply to the sampled fields and do not establish reductions in total lamp output, all-sky brightness, or light pollution at other locations. Because the comparison covered two nights, repeated measurements under comparable conditions are needed.

p. 8
Where the paper says it

They apply to the sampled fields and do not establish reductions in total lamp output, all-sky brightness, or light pollution at other locations. Because the comparison covered two nights, repeated measurements under comparable conditions are needed.

The retrofit retains the existing lamps and electrical systems, it also provides a relatively low-cost and practical approach to dark-sky protection at stargazing sites. p. 8
Where the paper says it

Directional shields can be evaluated as retrofits at stargazing sites using fixed viewing directions. Because the retrofit retains the existing lamps and electrical systems, it also provides a relatively low-cost and practical approach to dark-sky protection at stargazing sites.

p. 8
Where the paper says it

Directional shields can be evaluated as retrofits at stargazing sites using fixed viewing directions. Because the retrofit retains the existing lamps and electrical systems, it also provides a relatively low-cost and practical approach to dark-sky protection at stargazing sites.

The largest changes occurred in low-elevation views and varied by direction. Directional shields can be evaluated as retrofits at stargazing sites using fixed viewing directions. The comparison covered two nights, repeated measurements under comparable conditions are needed. The retrofit retains the existing lamps and electrical systems, it also provides a relatively low-cost and practical approach to dark-sky protection at stargazing sites.

REFERENCES

Aube, M. (2015). In: ´ Philosophical Transactions of the Royal Society B 370, p. p. 8

Where the paper says it

References Aube, M. In: ´ Philosophical Transactions of the Royal Society B 370, p.

20140117. doi: 10.1098/rstb.2014.0117.

Bara, S., C. Bao-Varela, and M. p. 8

Where the paper says it

In: ´ Philosophical Transactions of the Royal Society B 370, p. Bao-Varela, and M.

Kocifaj (2023). p. 8
Where the paper says it

Bao-Varela, and M. Kocifaj (2023).

In: ´ Journal of Quantitative Spectroscopy and Radiative Transfer 296, p. p. 8
Where the paper says it

Kocifaj (2023). In: ´ Journal of Quantitative Spectroscopy and Radiative Transfer 296, p.

108456. doi: 10.1016/j.jqsrt.2022.108456.

Cinzano, P. p. 1

Where the paper says it

We used a Unihedron SQM-L sky brightness meter. The SQM-L has an angular response with a full width at half maximum of about 20 degrees and reports readings in magnitudes per square arcsecond (Cinzano 2005).

(2005). ISTIL Internal Report 9. p. 8
Where the paper says it

Cinzano, P. ISTIL Internal Report 9.

Version 1.4.

Commission Internationale de l’Eclairage (2017). p. 8

Where the paper says it

com / projects / darksky / cd / reference/sqmreport_v1p4. Commission Internationale de l’Eclairage (2017).

CIE 150:2017. p. 8
Where the paper says it

Commission Internationale de l’Eclairage (2017). CIE 150:2017.

DarkSky International and Illuminating Engineering Society (2020). p. 8

Where the paper says it

´ doi: 10. DarkSky International and Illuminating Engineering Society (2020).

url: https://darksky. p. 8
Where the paper says it

url: https : / / unihedron . com / projects / darksky / cd / reference/sqmreport_v1p4.

org/resources/guides-andhow-tos/lighting-principles/

Falchi, Fabio, P. Cinzano, D. p. 1

Where the paper says it

We used a Unihedron SQM-L sky brightness meter. The SQM-L has an angular response with a full width at half maximum of about 20 degrees and reports readings in magnitudes per square arcsecond (Cinzano 2005).

Duriscoe, et al. p. 8
Where the paper says it

Cinzano, D. Duriscoe, et al.

(2016). In: Science Advances 2. p. 8
Where the paper says it

Duriscoe, et al. In: Science Advances 2.

6, e1600377. p. 8
Where the paper says it

In: Science Advances 2. 6, e1600377.

Gaston, K. J., T. W. Davies, J. Bennie, and J. p. 8

Where the paper says it

1126/sciadv. Bennie, and J.

Hopkins (2012). p. 8
Where the paper says it

Bennie, and J. Hopkins (2012).

In: Journal of Applied Ecology 49. p. 8
Where the paper says it

Hopkins (2012). In: Journal of Applied Ecology 49.

6, pp. 1256–1266. p. 8
Where the paper says it

In: Journal of Applied Ecology 49. 1256–1266.

Hanel, A., T. Posch, S. J. Ribas, et al. p. 8

Where the paper says it

1256–1266. Ribas, et al.

(2018). In: ¨ Journal of Quantitative Spectroscopy and Radiative Transfer 205, pp. p. 8
Where the paper says it

Ribas, et al. In: ¨ Journal of Quantitative Spectroscopy and Radiative Transfer 205, pp.

278–290.

Hsueh, M.-H. et al. (2021). In: Polymers 13. p. 8

Where the paper says it

In: ¨ Journal of Quantitative Spectroscopy and Radiative Transfer 205, pp. In: Polymers 13.

p. 8
Where the paper says it

In: ¨ Journal of Quantitative Spectroscopy and Radiative Transfer 205, pp. In: Polymers 13.

11, p. 1758.

Hung, L. W., S. J. Anderson, A Pipkin, and K Fristrup (2021). p. 8

Where the paper says it

Pipkin, and K. Fristrup (2021).

In: Journal of Environmental Management 292, p. p. 8
Where the paper says it

Fristrup (2021). In: Journal of Environmental Management 292, p.

112776.

Jechow, A., Z Kollath, S J Ribas, et al. p. 8

Where the paper says it

Kollath, S. Ribas, et al.

(2017). In: ´ Scientific Reports 7, p. p. 8
Where the paper says it

Ribas, et al. In: ´ Scientific Reports 7, p.

6741.

Jechow, A., S J Ribas, R Canal-Domingo, et al. p. 8

Where the paper says it

1038/s41598-017-06998-z. Canal-Domingo, et al.

(2018). In: Journal of Quantitative Spectroscopy and Radiative Transfer 209, pp. p. 8
Where the paper says it

Canal-Domingo, et al. In: Journal of Quantitative Spectroscopy and Radiative Transfer 209, pp.

212–223.

Katz, Y. and N Levin (2016). p. 0

Where the paper says it

Light levels can vary within a site with lamp orientation, visibility of the light-emitting surface, and nearby buildings or terrain. Katz and Levin (2016) found that SQM readings differ when the meter is aimed at the sky, ground, or horizon.

In: Remote Sensing of Environment 177, pp. p. 8
Where the paper says it

Levin (2016). In: Remote Sensing of Environment 177, pp.

65–77.

Kyba, C. C. M., Y O Altınta s¸, C E Walker, and M Newhouse (2023). p. 8

Where the paper says it

Walker, and M. Newhouse (2023).

In: Science 379. p. 8
Where the paper says it

Newhouse (2023). In: Science 379.

Kyba, C. C. M., T Kuester, A Sanchez de Miguel, et al. p. 8

Where the paper says it

Kuester, A. Sanchez de Miguel, et al.

(2017). In: ´ Science Advances 3. p. 8
Where the paper says it

Duriscoe, et al. In: Science Advances 2.

11, e1701528. p. 8
Where the paper says it

In: ´ Science Advances 3. 11, e1701528.

Kyba, C. C. M., K P Tong, J Bennie, et al. p. 8

Where the paper says it

1126/sciadv. Bennie, and J.

(2015). In: Scientific Reports 5, p. p. 8
Where the paper says it

Ribas, et al. In: ´ Scientific Reports 7, p.

8409.

Longcore, T. p. 0

Where the paper says it

6% in sky brightness at participants’ locations from 2011 to 2022. Artificial light at night can also affect animals’ nighttime activity (Longcore and Rich 2004).

and C Rich (2004). p. 0
Where the paper says it

6% in sky brightness at participants’ locations from 2011 to 2022. Artificial light at night can also affect animals’ nighttime activity (Longcore and Rich 2004).

In: Frontiers in Ecology and the Environment 2. p. 8
Where the paper says it

Rich (2004). In: Frontiers in Ecology and the Environment 2.

4, pp. 191–198.

Moreno Nieto, D et al. p. 1

Where the paper says it

Previous studies compared the mechanical and thermal properties of printed PETG and PLA and examined water absorption and degradation in both materials (Hsueh et al. 2021; Moreno Nieto et al.

(2021). In: Polymers 13.7, p. 1036.

Pogson, N. (1856). In: Monthly Notices of the Royal Astronomical Society 17. p. 8

Where the paper says it

3390/polym13071036. In: Monthly Notices of the Royal Astronomical Society 17.

1, pp. 12–15.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improve light field analysis by implementing direction-resolved measurements that are matched to expected shield function, as this supports the use of defined fields of view and pointing directions when evaluating local lighting interventions (Hanel et al. 2018).

  2. Enhance site assessment capabilities by incorporating measurements at multiple distances from the installation, as Several outside sites should be placed along comparable sightlines at increasing distances, with foreground obstructions documented at each position.

  3. Develop a workflow for existing lighting systems by creating a practical guide where Lamps with visible emitting surfaces can first be identified from observing and walking areas. Shields can then be fitted to these lamps.

Abstract

Road lighting at stargazing camps can cause glare and stray light that interfere with observation. We installed directional shields on existing solar-powered streetlights at Bayan Gol Starlight Camp in Inner Mongolia, China, and compared SQM-L measurements before and after installation at the camp center (P1) and a site approximately 500 m away (P2). Measurements were taken at elevations of 0, 30, 60, and 90. At 0, the mean SQM reading across four directions at P1 increased by 1.624, and the reading toward the camp at P2 increased by 2.312. These changes correspond to reductions of approximately 77.6% and 88.1% in the equivalent SQM signal within the measured fields of view. The largest changes occurred at 0; changes at 30 and above were smaller. Photographs taken with identical exposure settings showed less visible glare around the shielded lamps. The measurements indicate that the changes were concentrated in low-elevation views. Directional shields provide a relatively low-cost way to reduce unwanted light while retaining the existing road-lighting system.

Related papers