STarlight Acquisition and Reflection toward Interferometry (STARI) mission
Listen
Radio episode about this paper
Transcript
Introduction to the show: ident: Astrophysics. The day in astrophysics: observations, models and what the data forces.
Vera: We're looking at the paper: "STarlight Acquisition and Reflection toward Interferometry (STARI) mission".
Jocelyn: Here's the gist of the paper. STARI introduces two spacecraft technology demonstrator for future long-baseline interferometers that will perform in-space transfer of starlight between free-flying spacecraft The mission is designed to mature key technologies needed for future mission concepts such as the Large Interferometer for Exoplanets (LIFE) Mission Objectives and Design The basic observing task is to acquire a target star, send the beam across the formation, search for single-mode fiber coupling, and record the coupled flux to characterize throughput and stability STARI deliberately omits a combiner and delay line so that the project can concentrate on flight demonstrations that are difficult to reproduce on the ground The mission is not itself an interferometer, but rather a flight demonstration of a single interferometer arm involving free-space optical handoff between formation-flying spacecraft, coupling into single-mode fiber, and cm-level formation-flying control Hardware Architecture STARI is designed around two functionally redundant 8U CubeSats, each carrying the bus functions needed for power, command and data handling, attitude determination and control, communications, thermal management, and structure The payload architecture involves a PT spacecraft that uses a beamsplitter and retroreflector to image the target star and FID optical beacons in the same camera frame The FID spacecraft receives the relayed beam and injects it into a single-mode fiber using an off-axis parabola Control and Navigation The GNC system must maintain an “interferometer” geometry where the baseline between spacecraft is perpendicular to the line of sight within the dynamic environment of low Earth orbit Navigation relies on differential GNSS, LED-beacon imaging, payload camera centroids, and inter-satellite link for relative navigation The formation-flying strategy is driven by minimizing the optical path difference (OPD) of the observing geometry to keep it small Subsystem Development and Trade Studies The STARI team is organized around subsystem responsibilities, with Stanford University leading formation flying and GNC, Georgia Tech leading the cold-gas propulsion system, and Rensselaer Polytechnic Institute leading the fiber injection and detection (FID) optical subsystem Key trade studies focus on coupling stability sensitivity to tip-tilt, focus, lateral fiber placement, thermal gradients, and launch or thermal distortion of the OAP/fiber assembly Performance simulations aim to combine attitude control with relative orbit control and optical throughput measurements The mission success criteria are staged to reflect increasing levels of technology maturation, moving from threshold success to baseline and extended goals Future Work and Timeline Near-term pacing items for the January 2027 Design Review include completing bus/payload interface control, payload computer procurement, OAP and focus-mechanism trades, propulsion prototype testing, and a more complete end-to-end software architecture Flight-unit fabrication for the bus and subsystems is planned throughout 2027, followed by system integration in 2028 and launch readiness for an expected 2029 launch The mission targets a launch in 2029 The corresponding author is John D.
Vera: Monnier, monnier@umich.edu Acknowledgments STARI is supported by the NASA Astrophysics Research and Analysis (APRA) program The team thanks the December 2025 SRR review committee and reviewers for their detailed review and action items that helped mature the requirements, risk posture, and path to PDR Ongoing discussions with colleagues have been appreciated as the mission has matured ChatGPT was used during the production of this manuscript The Michigan Institute for Research in Astrophysics provided early seed support References
1: Monnier, J.
Jocelyn: D., “Optical interferometry in astronomy,” Reports on Progress in Physics 66, 789–857 (May 2003).
2: Lawson, P.
Title and authors: Vera: So, to put it simply, the paper describes STARI as a way to test the core mechanisms of in-space optical handoff between two satellites. It’s designed specifically to prove that you can successfully send light from one craft to another while keeping them in a stable relative position for observation.
Jocelyn: They aren't trying to be a full telescope yet; they are testing the fundamental physics of coupling light into a single-mode fiber over that free-space gap. That is where the real technology gaps they identified, like coupling stability and cm level formation flying control, are being addressed.
Subrahmanyan: It’s important to remember that STARI isn't an interferometer in the traditional sense. It’s a flight demonstration of a single interferometer arm: free-space optical handoff, fiber coupling, and centimeter level formation flying control. This is the technology gap they pinpointed from their KISS workshop report6.
Vera: They are essentially testing if you can maintain that perpendicular geometry between the spacecraft while simultaneously keeping the resulting optical path difference small enough for successful fiber coupling into a single-mode fiber. That’s the main operational hurdle they are tackling.
Jocelyn: And they're focusing on autonomous coordinated two-spacecraft operations as well, which means the spacecraft have to manage their relative motion and pointing without constant ground intervention.
Subrahmanyan: The implication for cosmology is that if they can successfully demonstrate this optical path difference control over a significant distance in orbit, it sets a necessary baseline for designing much larger, more complex interferometers like LIFE.
Vera: It’s about proving the physics works in space before you try to build the massive instruments on Earth. They are concentrating on these specific flight demonstrations because they are difficult to reproduce reliably on the ground.
Jocelyn: And they are testing how well their navigation system, using differential GNSS and LED beacons, can keep that geometry stable against the disturbances of low Earth orbit.
The paper's summary: Vera: Now let’s look at what they suggest as improvements to the mission concept itself. They are focusing on making sure their system can handle a wider range of challenges in real space.
Jocelyn: They are looking at ways to improve the AI system's ability to perform autonomous coordinated two-spacecraft operations by leveraging differential GNSS, visible LED beacons, and fast-steering mirrors in closed-loop control.
Subrahmanyan: That’s a big deal because it moves them toward sustaining diffraction limited, high throughput fiber coupling during formation flight. That suggests they want the system to be robust enough for science operations.
Vera: They are also aiming to achieve a sustained optical path difference control below fifty centimeters during science operations by using the Stanford-led formation flying strategy that keeps those two spacecraft close to a plane perpendicular to the line of sight.
Jocelyn: That level of OPD control is what enables them to aim for the stability needed for coupling into single-mode fiber, which is a key metric they’re tracking.
Subrahmanyan: And they are also looking at executing rapid retargeting between nearby stars by using an input-constrained impulsive optimal control strategy for spacecraft relative motion, specifically addressing minimum impulse bit requirements for formation control.
Vera: That strategy sounds like it addresses the need to move quickly and precisely when targeting different stars or adjusting the observation geometry rapidly.
Jocelyn: Plus, they are incorporating a project-generated hybrid jitter power spectrum from CubeSat pointing and vibration data reported for ASTERIA and HyTI into their tracking-jitter model.
Subrahmanyan: By using that kind of empirical data to model the jitter, they’re trying to get a more realistic picture of the noise they’ll be fighting in orbit.
The paper's improvements: Vera: So, wrapping up on this STARI mission paper, what it really means is that it’s a rigorous testbed for the physics and engineering challenges of building space-based optical links. It shows how important these flight demonstrations are to validating the design choices before moving to larger systems.
Jocelyn: They’ve established a clear path for maturing the technology from just demonstrating handoff to achieving sustained, stable optical coupling under real operational conditions in low Earth orbit.
Subrahmanyan: From a theoretical standpoint, this mission provides the context and data needed to understand how structure formation and large-scale cosmology observations might eventually be constrained by these types of instruments.
Vera: It’s a testament to how much work goes into just making the geometry stable enough for science. We're looking forward to seeing what kind of data comes out once they successfully complete those flight demonstrations.
Jocelyn: And we’ll keep watching for updates on how they tackle the autonomous control and the stability challenges in their next set of tests.
Subrahmanyan: I think this STARI mission really sets a realistic benchmark for the complexity that future space-interferometers will have to manage.
Conclusion: Vera: So we’ve looked at the STarlight Acquisition and Reflection toward Interferometry mission paper. Basically, they are testing if you can physically send light between two spacecraft in space and make it couple into a fiber.
Jocelyn: Right, it’s about those two CubeSats doing an in-space transfer of starlight to mature the technology for bigger projects like LIFE.
Subrahmanyan: From my side, this is really about setting the baseline physics for how we can constrain exoplanets using space-based interferometry later on.
Vera: They focused heavily on flight demonstrations because those specific coupling stability and centimeter level formation flying tricks are hard to test accurately on the ground.
Jocelyn: And they’re looking at making that system more autonomous, using differential GNSS and LED beacons to keep the spacecraft perfectly aligned.
Subrahmanyan: The idea of controlling a sustained optical path difference below fifty centimeters during science operations is a significant technical hurdle they are tackling right now.
Vera: That OPD control is what unlocks the ability to actually couple that light into the single-mode fiber they need for their main goal.
Jocelyn: And they’re using input-constrained optimal control strategies for spacecraft motion, which sounds like a smart way to handle rapid retargeting between nearby stars.
Subrahmanyan: It's about getting the minimum impulse bit right so the formation control is really tight when you need it.
Vera: They also incorporated jitter data from other satellites into their tracking model, which makes their noise characterization much more realistic for orbit science.
Jocelyn: So, overall, they’re moving away from just a proof-of-concept to something that looks more like a flight-ready demonstration of the whole optical handoff system.
Subrahmanyan: It’s an important step toward realizing the capabilities required for next generation exoplanet detection missions.
Vera: This STarlight Acquisition and Reflection toward Interferometry paper shows where the engineering needs to go before we can even think about building those massive future telescopes.
Jocelyn: Yeah, it’s a lot of work just to keep two bits of hardware perfectly positioned relative to each other in a dynamic environment like LEO.
Subrahmanyan: It gives us a clearer roadmap for the science goals that come after this technology matures.
John D. Monniera, James Cutlera, Akshat Dubeya, Caden Burkhardta, Raven St. Claira, Bradley Bialkea, Adrien Boissya, Tobey Changa, Ænnah Cherrya, ×hinder Ragav Lakshmi Kumara, Michael Meyera, × Jacob Klinglera, Shivani Sunila, Austin Thomasa™ Daniil Voloshina Simone D’Amicob Antonio Rizzab Ethan Fossb Samuel Y.W. Lowb Prachet Jainb E. Glenn Lightseyc Althea Noonanc Mark Gorrowc Leonid Pogorelyukd Melissa Floresd Albert Ostoja-Starzewskid Garret DeRosed Jasper Heymannd Alexa LaPintad Ryan Turoffd Gautam Vasishte and Kerri Cahoyf
University of Michigan · Stanford University · Georgia Institute of Technology · Rensselaer Polytechnic Institute · NASA Jet Propulsion Laboratory · Massachusetts Institute of Technology
astro-ph.IM
Submitted: 2026-11-09
Updated: 2026-11-09
Comments: 12 pages, 10 figures; author version of the published SPIE proceedings paper
Journal ref: Proc. SPIE 14145, 1414512 (2026)
DOI: 10.1117/12.3104103
License: http://arxiv.org/licenses/nonexclusive-distrib/1.0/
Importance score: 91/100
The gist: STARI introduces two spacecraft technology demonstrator for future long-baseline interferometers that will perform in-space transfer of starlight between free-flying spacecraft The mission is…
Key concepts
- Formation Flying
- This refers to controlling two or more spacecraft so they maintain a precise relative position and orientation with respect to each other while moving through space. In STARI, this is crucial for keeping the two CubeSats positioned correctly relative to each other to perform the optical measurements required for interferometry.
- Optical Path Difference (OPD)
- This is the difference in the distance light travels between two spacecraft when observing a target star. Minimizing this OPD is vital because it directly affects the quality of the interference measurement. STARI's control system works to keep this difference very small, below 50 cm.
- Single-Mode Fiber Coupling
- This is the process of efficiently directing light from a spacecraft onto a single optical fiber. In STARI, this involves injecting the relayed beam into a fiber using an off-axis parabola. This step is critical for characterizing how well the system can transmit and stabilize the light.
- Differential GNSS Navigation
- This is a navigation technique that uses signals from multiple Global Navigation Satellite Systems (GNSS) to determine precise location and motion. STARI uses this, along with LED beacons and camera data, to figure out exactly where each spacecraft is relative to the other in orbit.
Summary
STARI introduces two spacecraft technology demonstrator for future long-baseline interferometers that will perform in-space transfer of starlight between free-flying spacecraft The mission is designed to mature key technologies needed for future mission concepts such as the Large Interferometer for Exoplanets (LIFE)
Mission Objectives and Design
The basic observing task is to acquire a target star, send the beam across the formation, search for single-mode fiber coupling, and record the coupled flux to characterize throughput and stability STARI deliberately omits a combiner and delay line so that the project can concentrate on flight demonstrations that are difficult to reproduce on the ground The mission is not itself an interferometer, but rather a flight demonstration of a single interferometer arm involving free-space optical handoff between formation-flying spacecraft, coupling into single-mode fiber, and cm-level formation-flying control
Hardware Architecture
STARI is designed around two functionally redundant 8U CubeSats, each carrying the bus functions needed for power, command and data handling, attitude determination and control, communications, thermal management, and structure The payload architecture involves a PT spacecraft that uses a beamsplitter and retroreflector to image the target star and FID optical beacons in the same camera frame The FID spacecraft receives the relayed beam and injects it into a single-mode fiber using an off-axis parabola
Control and Navigation
The GNC system must maintain an “interferometer” geometry where the baseline between spacecraft is perpendicular to the line of sight within the dynamic environment of low Earth orbit Navigation relies on differential GNSS, LED-beacon imaging, payload camera centroids, and inter-satellite link for relative navigation The formation-flying strategy is driven by minimizing the optical path difference (OPD) of the observing geometry to keep it small
Subsystem Development and Trade Studies
The STARI team is organized around subsystem responsibilities, with Stanford University leading formation flying and GNC, Georgia Tech leading the cold-gas propulsion system, and Rensselaer Polytechnic Institute leading the fiber injection and detection (FID) optical subsystem Key trade studies focus on coupling stability sensitivity to tip-tilt, focus, lateral fiber placement, thermal gradients, and launch or thermal distortion of the OAP/fiber assembly Performance simulations aim to combine attitude control with relative orbit control and optical throughput measurements The mission success criteria are staged to reflect increasing levels of technology maturation, moving from threshold success to baseline and extended goals
Future Work and Timeline
Near-term pacing items for the January 2027 Design Review include completing bus/payload interface control, payload computer procurement, OAP and focus-mechanism trades, propulsion prototype testing, and a more complete end-to-end software architecture Flight-unit fabrication for the bus and subsystems is planned throughout 2027, followed by system integration in 2028 and launch readiness for an expected 2029 launch The mission targets a launch in 2029 The corresponding author is John D. Monnier, monnier@umich. p. 0 p. 0edu
Acknowledgments
STARI is supported by the NASA Astrophysics Research and Analysis (APRA) program The team thanks the December 2025 SRR review committee and reviewers for their detailed review and action items that helped mature the requirements, risk posture, and path to PDR Ongoing discussions with colleagues have been appreciated as the mission has matured ChatGPT was used during the production of this manuscript The Michigan Institute for Research in Astrophysics provided early seed support
References
[1] Monnier, J. D., “Optical interferometry in astronomy,” Reports on Progress in Physics 66, 789–857 (May 2003). p. 0
[2] Lawson, P. R., Lay, O. P., Martin, S. R., Peters, R. D., Gappinger, R. O., Ksendzov, A., Scharf, D. P., Booth, A. J., Beichman, C. A., Serabyn, E., Johnston, K. J., and Danchi, W. C., “Terrestrial Planet Finder Interferometer: 2007-2008 progress and plans,” in [Optical and Infrared Interferometry], Sch¨oller, M. p. 0, Danchi, W. C., and Delplancke, F., eds., Society of Photo-Optical Instrumentation Engineers (SPIE) Conference Series 7013, 70132N (July 2008). p. 8
[3] Alei, E., Konrad, B. S., Angerhausen, D., Grenfell, J. L., Molli´ere, P., Quanz, S. P., Rugheimer, S., Wunderlich, F., and LIFE Collaboration, “Large Interferometer For Exoplanets (LIFE). p. 0 V. Diagnostic potential of a mid-infrared space interferometer for studying Earth analogs,” A&A 665, A106 (Sept. p. 0 2022).
[4] Quanz, S. P., Ottiger, M., Fontanet, E., Kammerer, J., Menti, F., Dannert, F., Gheorghe, A., Absil, O., Airapetian, V. S., Alei, E., Allart, R., Angerhausen, D., Blumenthal, S., Buchhave, L. A., Cabrera, J., Carri´on-Gonz´alez, O., Chauvin, G., Danchi, W. C., Dandumont, C., Defr´ere, D., Dorn, C., Ehrenreich, D., ´Ertel, S., Fridlund, M., Garc´ıa Mu˜noz, A., Gasc´on, C., Girard, J. H., Glauser, A. M., Grenfell, J. L., Guidi, G., Hagelberg, J., Helled, R., Ireland, M. J., Janson, M., Kopparapu, R. K., Korth, J., Kozakis, T., Kraus, S., L´eger, A., Leedj¨arv, L., Lichtenberg, T., Lillo-Box, J., Linz, H., Liseau, R., Loicq, J., Mahendra, V., Malbet, F., Mathew, J., Mennesson, B., Meyer, M. R., Mishra, L., Molaverdikhani, K., Noack, L., Oza A. V., Pall´e E., Parviainen H., Quirrenbach A., Rauer H., Ribas I., Rice M., Romagnolo A., Rugheimer S., Schwieterman E. W., Serabyn E., Sharma S., Stassun K. G., Szul´agyi J., Wang H. S., Wunderlich F., Wyatt M. C. and the LIFE collaboration, “Large Interferometer For Exoplanets (LIFE). p. 0 I. improved exoplanet detection yield estimates for a large mid-infrared space-interferometer mission,” Astronomy & Astrophysics 664, A21 (Aug. p. 0 2022).
[5] Monnier, J. p. 0, Aarnio, A., Absil, O., Anugu, N., Baines, E., Bayo, A., Berger, J.-P., Cleeves, L. I., Dale, D., Danchi, W. C. de Wit W. J. Defr´ere D. Domagal-Goldman S. Elvis M. Froebrich D. Gai M., Gandhi P., Garcia P., Gardner T., Gies D., Gonzalez J.-F., Gunter B., Hoenig S., Ireland M., Jorgensen A. M., Kishimoto M., Klarmann L, Kloppenborg B, Kluska J, Knight J. S, Kral Q, Kraus S., Labadie L. Lawson P., Le Bouquin J.-B., Leisawitz D., Lightsey E. G., Linz H., Lipscy S., MacGregor M., Matsuo H., Mennesson B., Meyer M. R., Michael E. p. 0 A., Millour F, Mozurkewich D, Norris R., Ollivier M., Packham C., Petrov R., Pueyo L., Pope B., Quanz S. Ragland S., Rau G. Regaly Z., Riva A., Roettenbacher R., Savini G., Setterholm B. Sewilo M. Smith M. Spencer L. ten Brummelaar T. Turner N. van Belle G., Weigelt G., and Wittkowski M, “A Realistic Roadmap to Formation Flying Space Interferometry,” in [Bulletin of the American Astronomical Society], 51, 153 (Sept. p. 0 2019).
[6] Quanz, S. P., Mennesson, B., Beichman, C., Hansen, J. T., Dannert, F. A., Fortier, A., Ireland, M., Beltsten N., Alei E., Pogorelyuk L., Balmer W. O., Defr´ere D., Vasisht G., Fridlund M., Laugier R., Kataria T., Serabyn E., Ertel S., Rousseau H. Wagner K. Morgan R. van Belle G. T. Schaefer G. H. Berger J.-P., Matsuo T., Douglas E., Monnier J. p. 0 p. 0 D., Glauser A. M., Mawet D., and Meyer M. R., “Exploring Exoplanets with Interferometry,” (June 2026). p. 2 KISS Workshop Study Report. p. 2
[7] Monnier, J. p. 0 D., Jain, P., Kalluri, S., Cutler, J., D’Amico, S., Lightsey, G., Pogorelyuk L., Vasisht G., Cahoy K., and Meyer M., “STARI: starlight acquisition and reflection toward interferometry,” in [Space Telescopes and Instrumentation 2024: Optical, Infrared, and Millimeter Wave], Coyle L. p. 0 E., Matsuura S., and Perrin M. D., eds., Society of Photo-Optical Instrumentation Engineers (SPIE) Conference Series 13092, 130922Y (Aug. p. 8 2024).
[8] Nowak, M., Lacour, S., Crouzier, A., David, L., Lapeyr´ere V., and Schworer G., “Short life and abrupt death of PicSat, a small 3U CubeSat dreaming of exoplanet detection,” in [Space Telescopes and Instrumentation 2018: Optical, Infrared, and Millimeter Wave], Lystrup M. p. 0, MacEwen H. A., Fazio G. G., Batalha N., Siegler N., and Tong E. C., eds., Society of Photo-Optical Instrumentation Engineers (SPIE) Conference Series 10698, 1069821 (July 2018). p. 8
[9] Rizza, A. p. 4, Foss, E., Monnier, J. p. 0, Cutler, J. W., and D’Amico, S., “Space interferometry formation design using relative orbital elements: The STARI mission,” in [2026 IEEE Aerospace Conference], 1–15, IEEE (Big Sky MT USA) (Mar. p. 2 2026).
[10] Low, S. p. 0 Y. W., Bell, T., and D’Amico, S., “Flight-ready precise and robust carrier-phase GNSS navigation software for distributed space systems,” in [AIAA SciTech 2026 Forum], American Institute of Aeronautics and Astronautics, Orlando, FL USA (Jan. p. 2 2026).
[11] Foss, E. and D’Amico, S., “Efficient input-constrained impulsive optimal control of linear systems with application to spacecraft relative motion,” in [2026 IEEE American Control Conference (ACC)], (May 2026). p. 2
[12] Hart, S. T., Daniel, N. L., Hartigan, M. C., and Lightsey, E. G., “Design of the 3-D printed cold gas propulsion systems for the VISORS mission,” in [Proceedings of the 44th Annual American Astronautical Society Guidance, Navigation, and Control Conference, 2022], Sandnas M. p. 2 and Spencer D. B., eds., Advances in the Astronautical Sciences 179, 845–855, Springer, Cham (2024). p. 1
[13] Guffanti T., Bell T., Low S. Y. W., Murray-Cooper M., and D’Amico S., “Autonomous guidance navigation and control of the VISORS formation-flying mission,” in [2023 AAS/AIAA Astrodynamics Specialist Conference], (Aug. p. 2 2023). Paper AAS 23-149, August 13–17, 2023. p. 1
[14] Shields J. F., Pong C., Lo K., Jones L., Mohan S., Marom C., McKinley I., Wilson W., and Andrade L., “Characterization of CubeSat reaction wheel assemblies,” Journal of Small Satellites 6, 565–580 (May 2017). p. 7 Published May 22, 2017.
[15] Noonan A., Lightsey E. G., Monnier J., and Cutler J., “Design of a cold-gas propulsion system for the STARI mission,” in [2026 IEEE Aerospace Conference], 1–9, IEEE (2026). p. 2
[16] Pong C. M., “On-Orbit Performance & Operation of the Attitude & Pointing Control Subsystems on ASTERIA,” in [32nd Annual AIAA/USU Conference on Small Satellites], SSC18–PI–34 (2018). p. 8
[17] Urasaki C., Zhu F., Bottom M. p. 5, Nunes M., and Walk A., “Jitter Characterization of the HyTI Satellite,” in [2024 IEEE Aerospace Conference], (Mar. p. 8 2024).
BARE
STARI introduces two spacecraft technology demonstrator for future long-baseline interferometers that will perform in-space transfer of starlight between free-flying spacecraft The mission is designed to mature key technologies needed for future mission concepts such as the Large Interferometer for Exoplanets (LIFE)
The STARI team is organized around subsystem responsibilities, with Stanford University leading formation flying and GNC, Georgia Tech leading the cold-gas propulsion system, and Rensselaer Polytechnic Institute leading the fiber injection and detection (FID) optical subsystem Key trade studies focus on coupling stability sensitivity to tip-tilt, focus, lateral fiber placement, thermal gradients, and launch or thermal distortion of the OAP/fiber assembly Performance simulations aim to combine attitude control with relative orbit control and optical throughput measurements
Near-term pacing items for the January 2027 Design Review include completing bus/payload interface control, payload computer procurement, OAP and focus-mechanism trades, propulsion prototype testing, and a more complete end-to-end software architecture Flight-unit fabrication for the bus and subsystems is planned throughout 2027, followed by system integration in 2028 and launch readiness for an expected 2029 launch The corresponding author is John D. Monnier, monnier@umich.
Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.
Improvements for AI systems
-
Improved AI system can perform autonomous coordinated two-spacecraft operations by leveraging
differential GNSS, visible LED beacons, and fast-steering mirrors in closed-loop control
to sustain diffraction-limited, high-throughput fiber coupling during formation flight. -
The system can achieve a sustained optical path difference (OPD) control below 50 cm during science operations by utilizing the Stanford-led formation flying strategy designed to keep the
two spacecraft close to a plane perpendicular to the line of sight to the star.
-
The AI system can execute rapid retargeting between nearby stars by implementing an
input-constrained impulsive optimal control
strategy for spacecraft relative motion, specifically addressingminimum impulse bit
requirements for formation control. -
The system can perform in-flight characterization of propulsion and pointing jitter by incorporating a
project-generated hybrid jitter power spectrum from CubeSat pointing and vibration data reported for ASTERIA and HyTI
into its tracking-jitter model. -
The AI system can autonomously manage the transition between standby and science configurations by executing
programmed ahead of time
safe modes, including fallback paths if navigation, communications, attitude, propulsion, or payload state no longer matches the planned sequence.
Related papers
- On-sky demonstration of a vector Zernike wavefront sensor in a cascaded adaptive optics system
- Euclid Data Release 1 (DR1): Calibration strategy and observations
- The General Antiparticle Spectrometer (GAPS) Antarctic Balloon Payload
- Detection and excision of radio-frequency interference in radio arrays
- Unified matched-filter and excess-power pipeline for gravitational-wave detector characterization
- Ushering in sub-arcsecond angular resolution observatories in the far-infrared: The case for a double-Fourier interferometer