Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters

arXiv:2611.08098 · physics.optics · Submitted 2026-11-05 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: I'm Kai.

Mira: And I'm Mira, here with Lev.

Kai: We're looking at the paper: "Thermal Inverse Design".

Mira: Here's the gist of the paper. Microheaters underpin a broad range of applications that require localized and dynamic thermal control The approach uses a single lithographic step to pattern the doped regions of a silicon microheater and, in principle, enables on-demand peak temperature distributions under transient voltage excitation within one closed design loop.

Kai: The Core Problem Addressed The transient heater design problem is formulated as an inverse problem: given a target spatial temperature field Ttar(r) at a prescribed time ttar, determine a realizable spatial actuation that reproduces it under a specified electrical pulse.

Mira: The design variables may include local heat-source amplitudes, heater geometry, material or resistivity distributions, electrode arrangements, or electrical excitation.

Kai: To solve the transient heater-design problem, three coupled challenges must be tackled.

Paper summary: Kai: So this paper is called "Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters". It's about how to design these microheaters so they can create specific temperature patterns when you apply a pulse.

Mira: Exactly. The core idea is taking a target temperature field, Ttar, at some time ttar, and figuring out what physical setup—like the doping pattern of the silicon—you need to build it into so that it produces exactly that temperature field when you give it an electrical pulse.

Lev: It’s essentially turning a forward problem into an inverse problem where the output is a heat distribution, and you are solving for the input physical structure needed to make that happen.

Kai: And what makes this approach interesting is how they try to solve it all in one closed design loop using just one lithographic step to pattern those doped regions.

Mira: That's what they claim, right? They say this lets you get on-demand peak temperature distributions under a transient voltage excitation within that single loop.

Lev: But there are three major hurdles they have to overcome to make this work. First, thermal diffusion causes neighboring heat sources to produce strongly correlated responses in the temperature field, which makes fine-scale inversion really ill-conditioned and prone to power distributions that are either not unique or wildly oscillating.

Kai: So they have to deal with that correlation issue right away.

Mira: Right. And the second challenge is taking that inferred power distribution, which is just a mathematical idea of heat sources, and translating it into an actual continuous electrical layout while respecting minimum linewidth and spacing constraints for the fabrication process.

Lev: That translation step is tough because you have to satisfy those physical limits while trying to match the desired heat profile.

Kai: And the third challenge they mention is handling the temperature calculation itself, which involves nonlinear electrothermal correction when they finally check their design against a real simulation, like a finite-element method.

Mira: So, once you get a potential layout, you have to run that full simulation to see how accurate your design actually is and then use that error to update the power distribution and geometry.

Paper summary: Lev: That iterative feedback loop sounds computationally intensive because every time you update the power distribution based on the simulation error, it adds another layer of complexity.

Kai: So, what they do in their methodology is partition the heater into design cells, assign equivalent physical roles to these groups as virtual heat source groups, and then use transient simulations of those groups to build a response matrix relating their power densities to the temperature field at ttar.

Mira: That's step one of their process. They group things based on what they expect them to do thermally, not just where they are physically located on the chip.

Lev: Grouping cells with equivalent physical roles sounds like a smart way to reduce the degrees of freedom, which addresses that ill-conditioning issue we talked about earlier by restricting the solution space to smoother and more robust power distributions.

Kai: They then take those optimized cell powers and convert them into the widths of continuous doped silicon filaments connected between a single pair of electrodes.

Mira: So they move from these discrete cells to a physical layout description involving actual filament widths.

Lev: And finally, they evaluate that resulting physical layout using nonlinear transient electrothermal finite element method, and then they use the simulated error from that evaluation to update both the power distribution and the geometry for the next iteration.

Kai: The validation results show they've achieved some impressive things. For example, in one representative design, they showed a more than a twenty fold reduction in temperature nonuniformity when compared to a conventional uniformly doped heater.

Mira: And for their uniform-temperature design, the root mean square error of the field was three point three Kelvin compared to nine point zero one Kelvin for the reference heater.

Lev: That comparison against that reference number gives you a real sense of how much better this inverse design approach is at achieving a flat temperature. In a 1D one-dimensional one-dimensional one-R architecture, their inverse designed heater maintained a temperature close to the prescribed nine hundred Kelvin across most of the target region with an error of four point eight Kelvin <ref:2611.08098#pg1>.

Kai: It seems like they've shown versatility by compensating for thermal asymmetry introduced by things like a series connected diode and even generating prescribed linear temperature gradients.

Paper summary: Mira: So, they're not just designing for flat temperatures; they can tailor specific profiles too, which is really useful for controlling things in the microelectronics world.

Lev: The systematic width error analysis they do shows that voltage compensation helps restore the mean temperature while keeping a largely uniform temperature distribution, which is an important detail when you move from theory to actual hardware.

Kai: So, looking at the overall scope of "Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters", it seems they've established that inverse-designed doping is a scalable and fabrication compatible way to tailor those transient temperature distributions in resistive microheaters.

Mira: It’s about making the process less reliant on just trial and error.

Lev: The systematic width error analysis is a key piece of evidence that this method works when you consider the actual physical constraints of manufacturing.

Kai: So, thinking about the implications for what's out there, this work suggests we can move away from just simulating designs and start designing them directly from the desired thermal outcome using a closed loop approach.

Mira: It means for applications needing precise temperature control in things like sensing or material processing, you don't have to rely solely on massive simulation campaigns.

Lev: The real constraint, as they point out in their work, is that this method still needs to deal with the strong correlation between neighboring heat sources when doing that fine-scale inversion.

Kai: So the future work mentioned is incorporating group selection into a fully automated end-to-end inverse design process.

Mira: That would take it from a manual, iterative algorithm to something more integrated where the system chooses those equivalent physical roles automatically.

Lev: That level of automation would be necessary if you want this to move beyond just being a research tool and actually become something you could use for real hardware fabrication runs without constant manual intervention.

Kai: So, that's where it seems to land: establishing inverse-designed doping as a scalable approach for tailoring transient temperature distributions in resistive microheaters.

Mira: It’s about moving the design process from guessing and checking to directly engineering the thermal response from the start using this inverse method.

Conclusion: Kai: So, we're wrapping up on this paper about "Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters." Basically, they’ve shown you how to take a desired temperature map and figure out exactly what doping pattern you need in your silicon heater to achieve it with a pulse.

Mira: Yeah, I see the title and authors are involved. It’s about using an inverse problem approach to design these microheaters where the output is heat, and you solve for the physical structure that makes that happen under a voltage excitation.

Lev: From my side, what they're doing is mapping out how those desired heat distributions translate into actual physical filament widths in silicon, which is a huge hurdle for me when we think about building this on real hardware.

Kai: It’s interesting because they managed to tackle the ill-conditioning issue where neighboring heat sources create too much correlation in the temperature field, and they solved it by grouping cells with equivalent roles.

Mira: That grouping strategy really helps reduce the degrees of freedom, which means you aren't left with those weird, wildly oscillating power distributions we usually see when you try to solve this directly.

Lev: And they show validation results where they cut the temperature nonuniformity by over twenty times compared to a standard uniformly doped heater, which is significant for what we can actually measure in a lab.

Kai: And for the uniform-temperature case, they got their root mean square error down to three point three Kelvin when comparing it to the reference heater. That’s a solid number for achieving flatness in this kind of setup.

Mira: So, what this means is that you can design these thermal control systems directly from the thermal outcome instead of just guessing and tweaking parameters in a forward simulation loop.

Lev: The implication is that if we can get this fabrication-compatible approach working consistently, it changes how we prototype these on-chip heaters for things like sensing or localized heating.

Kai: Exactly. It moves us toward designing these thermal components with the final performance metric in mind from the start instead of designing a structure and hoping the heat profile works out later.

Mira: And that leads us to thinking about how this method handles those constraints, like compensating for asymmetries introduced by things like diodes, which they did successfully.

Lev: Right, it shows that even with real-world imperfections in the circuit design, you can still use this inverse design loop to restore a good mean temperature and keep the distribution relatively flat.

Kai: It’s a scalable approach for tailoring transient responses in these resistive microheaters, but they also point out that future work needs to focus on fully automating that group selection process.

Mira: That automation would take it from an iterative research tool to something you could use for end-to-end design processes without needing constant manual intervention.

Korea Advanced Institute of Science and Technology (KAIST) · Massachusetts Institute of Technology (MIT)

physics.optics

Submitted: 2026-11-05

Updated: 2026-11-05

Code: https://github.com/muzhanghuang-jpg/transient-inverse

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 83/100

The gist: Microheaters underpin a broad range of applications that require localized and dynamic thermal control The approach uses a single lithographic step to pattern the doped regions of a silicon…

Key concepts

Transient Heater Design Problem
This is an inverse problem where the goal is to find the necessary physical adjustments—like heat sources or geometry—to produce a desired spatial temperature field at a specific time after applying an electrical pulse. The challenge lies in mapping the required temperature output back to a realizable physical design.
Inverse Design Framework
This methodology integrates several techniques: regularized field inversion, layout synthesis constrained by fabrication limits, and nonlinear electrothermal correction. It systematically partitions the heater into groups to simplify the complex problem and iteratively refines the design until the simulated temperature matches the target field.
Ill-Conditioning Mitigation
Thermal diffusion causes neighboring heat sources to have highly correlated temperature responses, making precise inversion difficult. The method addresses this by grouping cells with similar physical roles, which reduces unnecessary variables and leads to smoother, more robust power distributions that are easier to fabricate.
Group Selection
This step involves assigning virtual heat-source groups to partitioned design cells based on their equivalent physical roles. This strategy simplifies the inversion process by restricting the solution space, ensuring that the resulting power distribution is physically meaningful and manufacturable.

Terminology

Summary

Microheaters underpin a broad range of applications that require localized and dynamic thermal control The approach uses a single lithographic step to pattern the doped regions of a silicon microheater and, in principle, enables on-demand peak temperature distributions under transient voltage excitation within one closed design loop. p. 0

Where the paper says it

Here, we introduce an inverse design algorithm for pulsed heating, a common operating modality in thermal processing, sensing, switching, and material characterization. The approach uses a single lithographic step to pattern the doped regions of a silicon microheater and, in principle, enables on-demand peak temperature distributions under transient voltage excitation within one closed design loop.

The Core Problem Addressed

The transient heater design problem is formulated as an inverse problem: given a target spatial temperature field Ttar(r) at a prescribed time ttar, determine a realizable spatial actuation that reproduces it under a specified electrical pulse. The design variables may include local heat-source amplitudes, heater geometry, material or resistivity distributions, electrode arrangements, or electrical excitation. p. 2

Where the paper says it

The transient heater design problem can be formulated as an inverse problem: given a target spatial temperature field Ttar(r) at a prescribed time ttar, determine a realizable spatial actuation that reproduces it under a specified electrical pulse. The design variables may include local heat-source amplitudes, heater geometry, material or resistivity distributions, electrode arrangements, or electrical excitation.

To solve the transient heater-design problem, three coupled challenges must be tackled. p. 2
Where the paper says it

More generally, prescribed transient thermal fields may be implemented through topology, distributed electrical control, or geometric encoding of the heat source. To solve the transient heater-design problem, three coupled challenges must be tackled.

Methodology for Inverse Design

The inverse-design framework integrates regularized field inversion, fabrication-constrained layout synthesis, and nonlinear electrothermal correction. The procedure comprises four steps:

  1. The heater domain is partitioned into design cells and cells with equivalent physical roles are assigned to virtual heat-source groups. p. 4

    Where the paper says it

    The procedure comprises four steps. First, the heater domain is partitioned into design cells and cells with equivalent physical roles are assigned to virtual heat-source groups.

  2. Transient simulations of these groups are used to construct a response matrix relating their power densities to the temperature field at ttar. p. 4

    Where the paper says it

    First, the heater domain is partitioned into design cells and cells with equivalent physical roles are assigned to virtual heat-source groups. Second, transient simulations of these groups are used to construct a response matrix relating their power densities to the temperature field at ttar.

  3. The optimized cell powers are converted into the widths of continuous doped silicon filaments connected between a single pair of electrodes. p. 4

    Where the paper says it

    Second, transient simulations of these groups are used to construct a response matrix relating their power densities to the temperature field at ttar. Third, the optimized cell powers are converted into the widths of continuous doped silicon filaments connected between a single pair of electrodes.

  4. The resulting physical layout is evaluated using nonlinear transient electrothermal FEM, and the simulated error is used to update the power distribution and geometry. p. 4

    Where the paper says it

    Third, the optimized cell powers are converted into the widths of continuous doped silicon filaments connected between a single pair of electrodes. Finally, the resulting physical layout is evaluated using nonlinear transient electrothermal FEM, and the simulated error is used to correct the power distribution and geometry.

Addressing Ill-Conditioning and Constraints

Thermal diffusion produces strongly correlated responses from neighboring source regions, rendering fine-scale inversion ill-conditioned and susceptible to non-unique or rapidly oscillating power distributions. Grouping cells with equivalent physical roles removes these unnecessary degrees of freedom and restricts the solution to smoother and more robust power distributions. p. 3

Where the paper says it

Physics-informed grouping reduces poorly distinguishable degrees of freedom, while constrained optimization determines the group powers required to approximate the prescribed temperature field. To ensure physical realizability, these powers are mapped to filament widths subject to minimum-linewidth and spacing constraints.

The cell pitch is chosen as the smallest value that can be implemented while maintaining the required fabrication margins. p. 5
Where the paper says it

It can therefore reduce both the minimum linewidth and the available line-to-line spacing. The cell pitch is consequently chosen as the smallest value that can be implemented while maintain6

Validation and Results

The inverse design successfully demonstrates versatility through three representative designs, including achieving more than a 20-fold reduction in temperature nonuniformity compared to a conventional uniformly doped heater. The method compensates for the thermal asymmetry introduced by a series-connected diode, and generates prescribed linear temperature gradients. p. 0

Where the paper says it

Second, inverse-designed doping effectively cancels the thermal gradient in a heater connected in series with a diode. Third, the method generates prescribed linear temperature gradients on demand.

For the uniform-temperature design, the RMSEfield is 3. p. 1
Where the paper says it

Mathieu-Potvin and Gosselin optimized thin film heater topology and electrode potentials for prescribed temperature profiles8 , Tan et al. used nonlinear finite-element analysis, feedback, and Tikhonov regularization to determine the input currents of a microheater array for uniform and linear surface-temperature targets9 , and Dao and Hu developed an inverse design scheme to achieve on-demand steadystate temperature profiles in doped Si microheaters10, which was experimentally validated to yield microheaters with considerably improved thermal uniformity11.

3 K compared to 90. p. 0
Where the paper says it

We demonstrate its versatility through three representative designs. First, an optimized heater achieves more than a 20-fold reduction in temperature nonuniformity compared with a conventional uniformly doped heater.

1 K for the reference heater. p. 7
Where the paper says it

Figure 3 shows the fourgroup square design, the six-group rectangular design used with one-sided diode-associated heating, and the 66-variable grouping used for the linear-gradient target. For a fixed pulse waveform, a reference simulation is performed for each group.

In a 1D1R architecture, the inverse-designed heater maintains a temperature close to the prescribed 900 K across most of the target region with an RMSEfield of 4. p. 0
Where the paper says it

Second, inverse-designed doping effectively cancels the thermal gradient in a heater connected in series with a diode. Third, the method generates prescribed linear temperature gradients on demand.

8 K.

Conclusion and Future Work

These results establish inverse-designed doping as a scalable and fabrication-compatible approach for tailoring transient temperature distributions in resistive microheaters. The systematic width error analysis shows that voltage compensation restores the mean temperature while retaining a largely uniform temperature distribution. p. 5

Where the paper says it

If the simulated temperature does not satisfy the error criteria, the power distribution and filament widths are updated and evaluated again. RMSEopt denotes the root-mean-square error of the boundary-averaged cell temperatures relative to the target.

Future work could incorporate group selection into a fully automated, end-to-end inverse-design process. p. 4
Where the paper says it

This process is repeated until both the thermal-error and fabrication criteria are satisfied. Design-cell definition and size selection The patterned heater domain, denoted by ΩH, is partitioned into rectangular design cells Ωij .

The authors acknowledge funding support provided by the Air Force Office of Scientific Research (AFOSR) under award FA9550-22-1-0532 and the National Science Foundation under award 2328839. The source code for the inverse-design simulation workflow is publicly available under the BSD 3-Clause License at https://github. p. 2
Where the paper says it

The transient heater design problem can be formulated as an inverse problem: given a target spatial temperature field Ttar(r) at a prescribed time ttar, determine a realizable spatial actuation that reproduces it under a specified electrical pulse. The design variables may include local heat-source amplitudes, heater geometry, material or resistivity distributions, electrode arrangements, or electrical excitation.

com/muzhanghuang-jpg/transient-inverse. p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

The authors have no conflicts to disclose. The paper is published on arXiv as arXiv:2611. p. 0
Where the paper says it

kim1@kaist. kr 1 arXiv:2611.

08098v1 [physics. p. 0
Where the paper says it

kr 1 arXiv:2611. 08098v1 [physics.

optics] 5 Nov 2026. p. 0
Where the paper says it

08098v1 [physics. optics] 5 Nov 2026

REFERENCES

N Lovecchio, G De Cesare, A Nascetti, F Costantini, and D Caputo, in 2021 21st International Conference on Solid-State Sensors, Actuators and Microsystems (Transducers) (2021) pp. 639–642

S M Lee, D C Dyer, and J W Gardner, Microelectronics Journal 34, 115 (2003)

T Iwaki, J A Covington, F Udrea, S Z Ali, P K Guha, and J W Gardner, Journal of Physics: Conference Series 15, 27 (2005)

C R´ıos, Q Du, Y Zhang, C.-C. Popescu, M Y Shalaginov, P Miller, C Roberts, M Kang, K A Richardson, T Gu, S A Vitale and J Hu PhotoniX 3 26 (2022)

C Zhong, H Ma, C Sun, M Wei, Y Ye, B Tang, P Zhang, R Liu, J Li L Li and H Lin Optics Express 29 23508 (2021)

Y Zhang, C Fowler, J Liang, B Azhar M Y Shalaginov S Deckoff-Jones S An J B Chou C M Roberts V Liberman M Kang C R´ıos K A Richardson C RiveroBaleine T Gu H Zhang and J Hu Nature Nanotechnology 16 661 (2021)

F Yang, K P Dao, S An, X Qiu, Y Zhang, J Hu and T Gu Journal of Optics 25 115102 (2023)

F Mathieu-Potvin and L Gosselin Journal of Heat Transfer 132 101302 (2010)

Y Tan, C Zheng, J T Wen, and A M Maniatty Inverse Problems in Science and Engineering 25 1259 (2017)

K P Dao and J Hu Journal of Applied Physics 136 225101 (2024)

V Tara, K P Dao, J Hu, and A Majumdar arXiv preprint arXiv:2606.08318 (2026)

H Sun, C Lian, F V´asquez-Aza S R Kari Y.-S Huang A Restelli S A Vitale I Takeuchi J Hu N Youngblood G Pavlidis and C A R. p. 0

Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

Ocampo Nature Communications 16 4291 (2025)

F Vasquez-Aza, H Sun, C Lian, Y.-S Huang, C. p. 0

Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

-Y Lee, S A Vitale, I Takeuchi, J Hu N Youngblood C A R. Ocampo et al IEEE Transactions on Electron Devices (2026)

M W Chase Jr NIST-JANAF Thermochemical Tables 4th ed Journal of Physical and Chemical Reference Data Monograph No. 9 (American Chemical Society and American Institute of Physics, 1998) pp. p. 0

Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

1–1951

H R Shanks, P D Maycock, P H Sidles, and G C Danielson Physical Review 130, 1743 (1963)

C J Glassbrenner and G A Slack Physical Review 134, A1058 (1964)

C.-C Popescu, K P Dao, L Ranno, B Mills, L Martin-Monier Y Zhang D Bono B Neltner T Gu J Hu K Aryana W M Humphreys H J Kim S Vitale P Miller C Roberts S Geiger D Callahan M Moebius M Kang K A Richardson and C A R. p. 0

Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

Ocampo Small Science 3 2300098 (2023)

C.-C Popescu, T Jokinen, W Yan, P S Ogunwumi T Rosca B Mills D Callahan D Horn T Gu and J Hu Optics Letters 51 2848 (2026)

H Sun, C Lian, F V´asquez-Aza S R Kari Y.-S Huang A Restelli S A Vitale I Takeuchi J Hu N Youngblood C A R. p. 0

Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

p. 0
Where the paper says it

Thermal Inverse Design: Tailoring the Transient Response of Resistive Micro-Heaters Muzhang Huang,1 Junhe Zhang,2 Khoi Phuong Dao,2 Juejun Hu,2 and Hyun Jung Kim1, a) 1)Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2)Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations.

Ocampo et al IEEE Transactions on Electron Devices (2026)

M W Chase Jr NIST-JANAF Thermochemical Tables 4th ed Journal of Physical and Chemical Reference Data Monograph No. 9 (American Chemical Society and American Institute of Physics, 1998) pp. 1–1951

H R Shanks, P D Maycock, P H Sidles, and G C Danielson Physical Review 130, 1743 (1963)

C J Glassbrenner and G A Slack Physical Review 134, A1058 (1964)

C.-C Popescu, K P Dao, L Ranno, B Mills, L Martin-Monier Y Zhang D Bono B Neltner T Gu J Hu K Aryana W M Humphreys H J Kim S Vitale P Miller C Roberts S Geiger D Callahan M Moebius M Kang K A Richardson and C A R. Ocampo Small Science 3 2300098 (2023)

C.-C Popescu, T Jokinen, W Yan, P S Ogunwumi T Rosca B Mills D Callahan D Horn T Gu and J Hu Optics Letters 51 2848 (2026)

H Sun, C Lian, F V´asquez-Aza S R Kari Y.-S Huang A Restelli S A Vitale I Takeuchi J Hu N Youngblood C A R. Ocampo et al IEEE Transactions on Electron Devices (2026)

M W Chase Jr NIST-JANAF Thermochemical Tables 4th ed Journal of Physical and Chemical Reference Data Monograph No. 9 (American Chemical Society and American Institute of Physics, 1998) pp. 1–1951

H R Shanks, P D Maycock, P H Sidles, and G C Danielson Physical Review 130, 1743 (1963)

C J Glassbrenner and G A Slack Physical Review 134, A1058 (1964)

C.-C Popescu, K P Dao, L Ranno, B Mills, L Martin-Monier Y Zhang D Bono B Neltner T Gu J Hu K Aryana W M Humphreys H J Kim S Vitale P Miller C Roberts S Geiger D Callahan M Moebius M Kang K A Richardson and C A R. Ocampo Small Science 3 2300098 (2017)

C.-C Popescu, T Jokinen, W Yan, P S Ogunwumi T Rosca B Mills D Callahan D Horn T Gu and J Hu Optics Letters 51 2848 (2026)

H Sun, C Lian, F V´asquez-Aza S R Kari Y.-S Huang A Restelli S A Vitale I Takeuchi J Hu N Youngblood C A R. Ocampo et al IEEE Transactions on Electron Devices (2026)

M W Chase Jr NIST-JANAF Thermochemical Tables 4th ed Journal of Physical and Chemical Reference Data Monograph No. 9 (American Chemical Society and American Institute of Physics, 1998) pp. 1–1951

H R Shanks, P D Maycock, P H Sidles, and G C Danielson Physical Review 130, 1743 (1963)

C J Glassbrenner and G A Slack Physical Review 134, A1058 (1964)

C.-C Popescu, K P Dao, L Ranno, B Mills, L Martin-Monier Y Zhang D Bono B Neltner T Gu J Hu K Aryana W M Humphreys H J Kim S Vitale P Miller C Roberts S Geiger D Callahan M Moebius M Kang K A Richardson and C A R. Ocampo Small Science 3 2300098 (2017)

C.-C Popescu, T Jokinen, W Yan, P S Ogunwumi T Rosca B Mills D Callahan D Horn T Gu and J Hu Optics Letters 51 2848 (2026)

H Sun, C Lian, F V´asquez-Aza S R Kari Y.-S Huang A Restelli S A Vitale I Takeuchi J Hu N Youngblood C A R. Ocampo et al IEEE Transactions on Electron Devices (2026)

M W Chase Jr NIST-JANAF Thermochemical Tables 4th ed Journal of Physical and Chemical Reference Data Monograph No. 9 (American Chemical Society and American Institute of Physics, 1998) pp. 1–1951

H R Shanks, P D Maycock, P H Sidles, and G C Danielson Physical Review 130, 1743 (1963)

C J Glassbrenner and G A Slack Physical Review 134, A1058 (1964)

C.-C Popescu, K P Dao, L Ranno, B Mills, L Martin-Monier Y Zhang D Bono B Neltner T Gu J Hu K Aryana W M Humphreys H J Kim S Vitale P Miller C Roberts S Geiger D Callahan M Moebius M Kang K A Richardson and C A R. Ocampo Small Science 3 2300098 (2017)

C.-C Popescu, T Jokinen, W Yan, P S Ogunwumi T Rosca B Mills D Callahan D Horn T Gu and J Hu Optics Letters 51 2848 (2026)

H Sun, C Lian, F V´asquez-Aza S R Kari Y.-S Huang A Restelli S A Vitale I Takeuchi J Hu N Youngblood C A R. Ocampo et al IEEE Transactions on Electron Devices (2026)

M W Chase Jr NIST-JANAF Thermochemical Tables 4th ed Journal of Physical and Chemical Reference Data Monograph No. 9 (American Chemical Society and American Institute of Physics, 1998) pp. 1–1951

H R Shanks, P D Maycock, P H Sidles, and G C Danielson Physical Review 130, 1743 (1963)

C J Glassbrenner and G A Slack Physical Review 134, A1058 (1964)

C.-C Popescu, K P Dao, L Ranno, B Mills, L Martin-Monier Y Zhang D Bono B Neltner T Gu J Hu K Aryana W M Humphreys H J Kim S Vitale P Miller C Roberts S Geiger D Callahan M Moebius M Kang K A Richardson and C A R. Ocampo Small Science 3 2300098 (2017)

C.-C Popescu, T Jokinen, W Yan, P S Ogunwumi T Rosca B Mills D Callahan D Horn T Gu and J Hu Optics Letters 51 2848 (2026)

H Sun, C Lian, F V´asquez-Aza S R Kari Y.-S Huang A Restelli S A Vitale I Takeuchi J Hu N Youngblood C A R. Ocampo et al IEEE Transactions on Electron Devices (2026)

M W Chase Jr NIST-JANAF Thermochemical Tables 4th ed Journal of Physical and Chemical Reference Data Monograph No. 9 (American Chemical Society and American Institute of Physics, 1998) pp. 1–1951

H R Shanks, P D Maycock, P H Sidles, and G C Danielson Physical Review 130, 1743 (1963)

C J Glassbrenner and G A Slack Physical Review 134, A1058 (1964)

C.-C Popescu, K P Dao, L Ranno, B Mills, L Martin-Monier Y Zhang D Bono B Neltner T Gu J Hu K Aryana W M Humphreys H J Kim S Vitale P Miller C Roberts S Geiger D Callahan M Moebius M Kang K A Richardson and C A R. Ocampo Small Science 3 2300098 (2017)

C.-C Popescu, T Jokinen, W Yan, P S Ogunwumi T Rosca B Mills D Callahan D Horn T Gu and J Hu Optics Letters 51 2848 (2026)

H Sun, C Lian, F V´asquez-Aza S R Kari Y.-S Huang A Restelli S A Vitale I Takeuchi J Hu N Youngblood C A R. Ocampo et al IEEE Transactions on Electron Devices (2026)

M W Chase Jr NIST-JANAF Thermochemical Tables 4th ed Journal of Physical and Chemical Reference Data Monograph No. 9 (American Chemical Society and American Institute of Physics, 1998) pp. 1–1951

H R Shanks, P D Maycock, P H Sidles, and G C Danielson Physical Review 130, 1743 (1963)

C J Glassbrenner and G A Slack Physical Review 134, A1058 (1964)

C.-C Popescu, K P Dao, L Ranno, B Mills, L Martin-Monier Y Zhang D Bono B Neltner T Gu J Hu K Aryana W M Humphreys H J Kim S Vitale P Miller C Roberts S Geiger D Callahan M Moebius M Kang K A Richardson and C A R. Ocampo Small Science 3 2300098 (2017)

C.-C Popescu, T Jokinen, W Yan, P S Ogunwumi T Rosca B Mills D Callahan D Horn T Gu and J Hu Optics Letters 51 2848 (2026)

H Sun, C Lian, F V´asquez-Aza S R Kari Y.-S Huang A Restelli S A Vitale I Takeuchi J Hu N Youngblood C A R. Ocampo et al IEEE Transactions on Electron Devices (2026)

M W Chase Jr NIST-JANAF Thermochemical Tables 4th ed Journal of Physical and Chemical Reference Data Monograph No.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved AI system can perform on-demand design of pulsed heating elements by using an inverse design algorithm that uses a single lithographic step to pattern doped regions, enabling on-demand peak temperature distributions under transient voltage excitation within one closed loop.

  2. The improved system can handle fabrication constraints by incorporating practical fabrication constraints, including finite lithographic resolution directly into the inverse design process to ensure realized layouts are manufacturable.

  3. The system can achieve significant thermal uniformity improvements, such as more than a 20-fold reduction in temperature nonuniformity compared with a conventional uniformly doped heater, by tailoring the doping pattern to cancel thermal gradients or generate prescribed linear temperature gradients on demand.

  4. The AI system can solve complex inverse problems by integrating regularized field inversion, fabrication-constrained layout synthesis, and nonlinear electrothermal correction to address challenges like ill-conditioned responses from thermal diffusion and the nonlinearity of temperature-dependent material properties.

  5. The improved system can generate physically realistic electrical layouts by mapping optimized group powers to filament widths subject to minimum linewidth and spacing constraints, ensuring that the resulting geometry is geometrically admissible.

  6. The AI system can maintain performance under realistic operating conditions by employing a closed-loop iterative framework where the physical layout is evaluated using a nonlinear transient electrothermal finite-element method (FEM) simulations and updated until both thermal error and fabrication criteria are satisfied.

  7. The system can compensate for complex thermal asymmetries, such as those introduced by series-connected diodes in 1D1R architectures, by employing group powers that preserve both in-plane symmetries or using separate power variables to allow for compensation of one-sided external heat input.

  8. The system can generate spatially varying temperature fields, including linear gradients and uniform distributions, through group power optimization and subsequent nonlinear correction steps that account for temperature-dependent material properties and current redistribution.

Abstract

Microheaters underpin a broad range of applications that require localized and dynamic thermal control. Engineering their spatial and temporal temperature distributions is therefore essential, yet conventional heater design relies largely on iterative trial and error involving numerous full-scale thermal simulations. Here, we introduce an inverse design algorithm for pulsed heating, a common operating modality in thermal processing, sensing, switching, and material characterization. The approach uses a single lithographic step to pattern the doped regions of a silicon microheater and, in principle, enables on-demand peak temperature distributions under transient voltage excitation within one closed design loop. The algorithm also incorporates practical fabrication constraints, including finite lithographic resolution. We demonstrate its versatility through three representative designs. First, an optimized heater achieves more than a 20-fold reduction in temperature nonuniformity compared with a conventional uniformly doped heater. Second, inverse-designed doping effectively cancels the thermal gradient in a heater connected in series with a diode. Third, the method generates prescribed linear temperature gradients on demand. These results establish inverse-designed doping as a scalable and fabrication-compatible approach for tailoring transient temperature distributions in resistive microheaters.

Sources

Related papers