Low cross-plane thermal conductivity of kappa-Ga 2 O 3 thin films
Listen
Radio episode about this paper
Transcript
Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.
Kai: We're looking at the paper: "Low cross-plane thermal conductivity of kappa-Ga 2 O 3 thin films".
Mira: Here's the gist of the paper. The thermal conductivities of (001) κ-Ga2O3 thin films deposited on c-plane sapphire substrates were measured with frequency-domain thermoreflectance (FDTR) to investigate their size and temperature dependence, revealing that the cross-plane thermal conductivity ranges from 1.83 +0.19 −0.18 W/m·K to 2.26 +0.35 −0.40 W/m·K across thicknesses from 159 nm to 689 nm Experimental Results and Size Dependence The thermal conductivities of (001) κ-Ga2O3 thin films increased from 1.83 +0.19 −0.18 W/m·K to 2.26 +0.35 −0.40 W/m·K as the thicknesses increased from 159 nm to 689 nm This weak thickness dependence indicates that the majority of the intrinsic phonon mean free paths are smaller than the range of investigated film thicknesses First-principlesbased calculations that include phonon-phonon and phonon-boundary scattering capture this size-dependent behavior and support our experimental observation Structural and Crystallographic Analysis The as-grown κ films showed only (002) and (004) κ-Ga2O3 peaks other than the substrate peak in HR-XRD patterns Cross-sectional transmission electron microscopy revealed that ∼3 monolayers of pseudomorphic α-Ga2O3 form on the c-plane sapphire substrate, followed by a ∼20 nm transition layer containing a mixture of β and γ phase, with phase-pure κ on top of the transition layer The presence of such in-plane rotational domains is due to the nature of 6-fold symmetry of the c-plane sapphire substrate Temperature Effects and Scattering Mechanisms Temperature-dependent measurements showed a decrease in thermal conductivity with increasing temperature for a 689 nm film from 293 to 400 K due to enhanced phonon-phonon scattering A weaker temperature dependence was observed in a 159 nm film where phonon-boundary scattering becomes more prominent The temperature-dependent thermal conductivities were fitted using k = AT −n, yielding n = 0.23 (95% CI: 0.17-0.29) for the 159 nm film and n = 0.93 (95% CI: 0.61-1.26) for the 689 nm film Comparison with Other Polymorphs and Physical Interpretation At comparable film thicknesses, our measured κ-Ga2O3 films exhibit lower values of cross-plane thermal conductivity than the other experimentally measured Ga2O3 polymorphs This observation is consistent with lattice thermal conductivities predicted by first principles and suggests that the low thermal conductivity of κ-Ga2O3 results from its complex crystal structure, which leads to increased anharmonicity and lower phonon group velocities relative to other polymorphs Since the thermal conductivity of thin-film κ-Ga2O3 is dominated by phonon-phonon scattering, increasing the film thickness is not expected to enhance its thermal conductivity significantly The weak size dependence observed in the thermal conductivity of κ-Ga2O3 is attributed to its intrinsically short phonon MFPs The findings highlight the need for alternative thermal management strategies, such as integration with high thermal conductivity substrates (e.g., diamond or SiC) or engineered composite stacks, for κ-Ga2O3-based power and RF electronics The temperature-dependent measurements show that the junction temperature of Ga2O3-based devices can reach up to 200 ◦C where the thermal conductivity of κ-Ga2O3 is further reduced Supplementary Material see the supplementary material for thin film strain and surface morphology characterization (Figs.
Kai: S1 and S2); film thicknesses and associated uncertainties (Table S1); parameters used in the BPE uncertainty analysis (Table S2) and BPE posterior results for all six films (Figs.
Mira: S3-S8); BPE posterior results for the thickness-dependent measurements (Table S3) and the temperature-dependent measurements of the 159 nm and 689 nm films (Tables S4 and S5, respectively); details of the linear extrapolation method used to estimate G23 (Sec.
Kai: S4 and Fig.
Paper summary: Kai: So wrapping up the paper "Low cross-plane thermal conductivity of kappa-Ga two O three thin films," the main takeaway is that you see this weak size dependence in thermal conductivity because the intrinsic phonon mean free paths are intrinsically short in these materials > <ref:2611.05647#pg3,Low cross-plane thermal conductivity of>
Mira: That finding, combined with their structural analysis showing those transition layers, really highlights how complex the crystal structure is for kappa gallium oxide >
Lev: From an engineering view, it means we can't rely on simply making the film thicker to improve thermal transport; you need to think about the scattering mechanisms directly >
Kai: They also pointed out that in terms of temperature dependence, you get two different behaviors depending on whether you're looking at a thin or thick kappa gallium oxide film >
Mira: And they confirmed that for comparable thicknesses, the measured cross-plane thermal conductivities of kappa gallium oxide are lower than other gallium oxide polymorphs because of its complex structure >
Lev: Ultimately, this work suggests that for using these materials in high performance electronics, we should focus on finding ways to manage the heat flow at the interfaces or by combining them with substrates that have much higher thermal conductivity than sapphire >
Conclusion: Kai: So, we're wrapping up this paper on low cross-plane thermal conductivity of kappa gallium oxide thin films.
Mira: Basically, they looked at these films and found that the thermal conductivity isn't really improving just by making them thicker.
Lev: That weak size dependence is tied to how short those phonon mean free paths are inside the kappa phase itself.
Kai: Right, so it’s not just about thickness anymore; it’s about the internal structure of this specific crystal form.
Mira: And that structure—the more distorted Ga-O polyhedra they have—that's what lowers the average bond stiffness and slows down those phonon group velocities we need.
Lev: From a hardware standpoint, that means scaling up the material thickness won't give us the thermal performance boost we hoped for in this specific setup.
Kai: It makes me think about how we design these devices; if you can’t rely on thicker films for heat sinking, what else is left?
Mira: They also pointed out that at the temperatures you hit, like two hundred degrees Celsius, the thermal conductivity drops even more.
Lev: That temperature dependence gets worse when we push the limits of operation because those phonon-phonon scattering events get stronger.
Kai: So, if we’re building power electronics or RF components with kappa gallium oxide, we really need to focus on interface engineering instead of just material thickness.
Seungwon Park, Jingyu Tang, Minsung An, Alan J. H. McGaughey, Lisa M. Porter, Robert F. Davis, Jonathan A. Malen
Department of Mechanical Engineering, Carnegie Mellon University, Pittsburgh, Pennsylvania and Department of Materials Science and Engineering, Carnegie Mellon University, Pittsburgh, Pennsylvania
cond-mat.mtrl-sci, physics.app-ph
Submitted: 2026-11-03
Updated: 2026-11-03
License: http://creativecommons.org/licenses/by/4.0/
Importance score: 88/100
The gist: The thermal conductivities of (001) κ-Ga2O3 thin films deposited on c-plane sapphire substrates were measured with frequency-domain thermoreflectance (FDTR) to investigate their size and temperature…
Key concepts
- Cross-plane Thermal Conductivity
- This measures how well heat moves perpendicular to the film surface. In this study, it was found to be relatively low (around 1.83 to 2.26 W/m·K) for kappa-Ga2O3 films, which is crucial for understanding device performance and heat dissipation.
- Phonon Mean Free Path (MFP)
- Phonons are the quantum mechanical vibrations in a crystal that carry heat. The MFP is the average distance these vibrations travel before scattering. The paper suggests that kappa-Ga2O3 has intrinsically short MFPs, meaning phonons scatter frequently, which limits its thermal conductivity.
- Size Dependence
- This refers to how the thermal conductivity changes as the physical thickness of the thin film is varied. The study found a weak size dependence because most of the heat transport is limited by internal crystal structure rather than just film thickness, indicating short phonon MFPs in this material.
Terminology
Summary
The thermal conductivities of (001) κ-Ga2O3 thin films deposited on c-plane sapphire substrates were measured with frequency-domain thermoreflectance (FDTR) to investigate their size and temperature dependence, revealing that the cross-plane thermal conductivity ranges from 1. p. 0 edu)
(Dated: 5 November 2026)
The thermal conductivities of (001) κ-Ga2O3 thin films deposited on c-plane sapphire substrates were measured with
frequency-domain thermoreflectance (FDTR). The thermal conductivity increases from 1.Where the paper says it
Experimental Results and Size Dependence
The thermal conductivities of (001) κ-Ga2O3 thin films increased from 1.83 +0.19 −0.18 W/m·K to 2.26 +0.35 −0.40 W/m·K as the thicknesses increased from 159 nm to 689 nm This weak thickness dependence indicates that the majority of the intrinsic phonon mean free paths are smaller than the range of investigated film thicknesses First-principlesbased calculations that include phonon-phonon and phonon-boundary scattering capture this size-dependent behavior and support our experimental observation
Structural and Crystallographic Analysis
The as-grown κ films showed only (002) and (004) κ-Ga2O3 peaks other than the substrate peak in HR-XRD patterns Cross-sectional transmission electron microscopy revealed that ∼3 monolayers of pseudomorphic α-Ga2O3 form on the c-plane sapphire substrate, followed by a ∼20 nm transition layer containing a mixture of β and γ phase, with phase-pure κ on top of the transition layer The presence of such in-plane rotational domains is due to the nature of 6-fold symmetry of the c-plane sapphire substrate
Temperature Effects and Scattering Mechanisms
Temperature-dependent measurements showed a decrease in thermal conductivity with increasing temperature for a 689 nm film from 293 to 400 K due to enhanced phonon-phonon scattering A weaker temperature dependence was observed in a 159 nm film where phonon-boundary scattering becomes more prominent The temperature-dependent thermal conductivities were fitted using k = AT −n, yielding n = 0.23 (95% CI: 0.17-0.29) for the 159 nm film and n = 0. p. 0 40
W/m·K as the thicknesses increase from 159 nm to 689 nm. This weak thickness dependence indicates that the majority
of the intrinsic phonon mean free paths are smaller than the range of investigated film thicknesses.Where the paper says it
Comparison with Other Polymorphs and Physical Interpretation
At comparable film thicknesses, our measured κ-Ga2O3 films exhibit lower values of cross-plane thermal conductivity than the other experimentally measured Ga2O3 polymorphs This observation is consistent with lattice thermal conductivities predicted by first principles and suggests that the low thermal conductivity of κ-Ga2O3 results from its complex crystal structure, which leads to increased anharmonicity and lower phonon group velocities relative to other polymorphs Since the thermal conductivity of thin-film κ-Ga2O3 is dominated by phonon-phonon scattering, increasing the film thickness is not expected to enhance its thermal conductivity significantly
Conclusion and Future Directions
The weak size dependence observed in the thermal conductivity of κ-Ga2O3 is attributed to its intrinsically short phonon MFPs The findings highlight the need for alternative thermal management strategies, such as integration with high thermal conductivity substrates (e.g., diamond or SiC) or engineered composite stacks, for κ-Ga2O3-based power and RF electronics The temperature-dependent measurements show that the junction temperature of Ga2O3-based devices can reach up to 200 ◦C where the thermal conductivity of κ-Ga2O3 is further reduced
Supplementary Material see the supplementary material for thin film strain and surface morphology characterization (Figs. S1 and S2); film thicknesses and associated uncertainties (Table S1); parameters used in the BPE uncertainty analysis (Table S2) and BPE posterior results for all six films (Figs. p. 4 Supplementary Material
See the supplementary material for thin film strain and surface morphology characterization (Figs. S1 and S2); film
thicknesses and associated uncertainties (Table S1); parameters used in the BPE uncertainty analysis (Table S2) and BPE
posterior results for all six films (Figs. S1 and S2); film
thicknesses and associated uncertainties (Table S1); parameters used in the BPE uncertainty analysis (Table S2) and BPE
posterior results for all six films (Figs. S3-S8); BPE posterior
results for the thickness-dependent measurements (Table S3)
and the temperature-dependent measurements of the 159 nm
and 689 nm films (Tables S4 and S5, respectively); details of
the linear extrapolation method used to estimate G23 (Sec. 2,27
High-resolution X-ray diffraction (HR-XRD) patterns of
the as-grown κ films were acquired using a Panalytical X’pert
Pro MPD X-ray diffractometer equipped with a four-crystal
Ge (220) monochromator. As shown in Fig. S4
and Fig. S9); thermal conductivity results after removing G23
for the thickness- and temperature-dependent measurements
(Tables S6 and S7, respectively); phase lag data and analytical solution fits for the temperature-dependent measurements
of the 159 nm and 689 nm films (Figs. S9); thermal conductivity results after removing G23
for the thickness- and temperature-dependent measurements
(Tables S6 and S7, respectively); phase lag data and analytical solution fits for the temperature-dependent measurements
of the 159 nm and 689 nm films (Figs. S10 and S11, respectively); a power-law analysis of the temperature-dependent
thermal conductivity (Fig. S10 and S11, respectively); a power-law analysis of the temperature-dependent
thermal conductivity (Fig. S12); sensitivity analyses for the
341 nm and 689 nm films (Figs. The authors acknowledge the
use of the Bertucci Nanotechnology Laboratory at Carnegie
Mellon University supported by grant BNL-78657879 and use
of the Materials Characterization Facility at Carnegie Mellon University supported by grant MCF-677785. The authors
thank Jinkyu Kim for performing the AFM imaging and surface morphology characterization.Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Author’s Contributions Seungwon Park conceptualization (lead); Data curation (lead); Formal analysis (lead); Methodology (lead); Software (lead); Visualization (lead); Validation (lead); Writing - original draft (lead); Writing - review & editing (lead) Jingyu Tang conceptualization equal; Data curation equal; Formal analysis equal; Visualization equal; Writing - original draft equal; Writing - review & editing equal Minsung An data curation support; Formal analysis lead; Methodology support; Software support; Validation support Writing - review & editing support Alan J. H. McGaughey funding acquisition lead Project administration lead Supervision lead Writing - review & editing lead Lisa M. p. 4 Minsung An: Data curation (support); Formal analysis (lead);
Methodology (support); Software (support); Validation (support); Writing - review & editing (support). McGaughey: Funding acquisition (lead); Project administration
(lead); Supervision (lead); Writing - review & editing (lead). McGaughey: Funding acquisition (lead); Project administration
(lead); Supervision (lead); Writing - review & editing (lead). Porter: Funding acquisition (lead); Project administration (lead); Supervision (lead); Writing - review & editing
(lead). Davis: Funding acquisition (lead); Project
administration (lead); Supervision (lead); Writing - review
& editing (lead). Jonathan A.Where the paper says it
Where the paper says it
Where the paper says it
References R. Roy, V. G. Hill, and E. p. 4 Data Availability
The data that support the findings of this study are available
from the corresponding author upon reasonable request. Hill, and E. Hill, and E. Osborn, “Polymorphism of Ga2O3 and the System Ga2O3—H2O,” Journal of the American Chemical Society 74, 719–
722 (1952), publisher: American Chemical Society (ACS). Osborn, “Polymorphism of Ga2O3 and the System Ga2O3—H2O,” Journal of the American Chemical Society 74, 719–
722 (1952), publisher: American Chemical Society (ACS). Kurchin, L. McGaughey,1 Lisa M. Porter,2 Robert F. Porter, and R. Davis, “Thermal stability and phase transformation of α-, κ(ε)-, and γGa2O3 films under different ambient conditions,” Applied Physics Letters
125, 092104 (2024). Maccioni and V. Fiorentini, “Phase diagram and polarization of stable
phases of (Ga1−xInx)2O3,” Applied Physics Express 9, 041102 (2016). Malen, “Size effects and temperature dependence in the thermal conductivity of γ-Ga2O3 films,” Applied Physics Letters 126, 232201
(2025). Chen, “Thermal conductivity and ballistic-phonon transport in the crossplane direction of superlattices,” Physical Review B 57, 14958–14973
(1998). Pei, and G. Wang, “ε-Ga2O3 : An Emerging Wide Bandgap
Piezoelectric Semiconductor for Application in Radio Frequency Resonators,” Advanced Science 9, 2203927 (2022). Pei, and G. Wang, “ε-Ga2O3 : An Emerging Wide Bandgap
Piezoelectric Semiconductor for Application in Radio Frequency Resonators,” Advanced Science 9, 2203927 (2022). Low cross-plane thermal conductivity of κ-Ga2O3 thin films 6
ing Candidate for High-Electron-Mobility Transistors,” IEEE Electron Device Letters , 1–1 (2020). Miranda Cortez, X. Krishna,
and X. Li, “κ/β-Ga2O3 Type-II Phase Heterojunction,” Advanced Materials
37, 2406902 (2025). Gautam, and M. Razeghi, “High Thermal Stability of
κ-Ga2O3 Grown by MOCVD,” Crystals 11, 446 (2021). 0 W/m·K with thickness increasing from 12 nm
to 600 nm. 16 Song et al. 0 W/m·K with thickness increasing from 12 nm
to 600 nm. 16 Song et al. 0 W/m·K with thickness increasing from 12 nm
to 600 nm. 16 Song et al. 0 W/m·K with thickness increasing from 12 nm
to 600 nm. 16 Song et al. Porter,
and J. Malen, “Size effects and temperature dependence in the thermal conductivity of γ-Ga2O3 films,” Applied Physics Letters 126, 232201
(2025). Pang, and M. Liu, “An Overview
of the Ultrawide Bandgap Ga2O3 Semiconductor-Based Schottky Barrier
Diode for Power Electronics Application,” Nanoscale Research Letters 13,
290 (2018). Liu, “An Overview
of the Ultrawide Bandgap Ga2O3 Semiconductor-Based Schottky Barrier
Diode for Power Electronics Application,” Nanoscale Research Letters 13,
290 (2018). Higashiwaki, “β-Ga2O3 material properties, growth technologies, and
devices: a review,” AAPPS Bulletin 32, 3 (2022). Yamamoto, and K. Shimamura,
“Epitaxial growth of phase-pure ε-Ga2O3 by halide vapor phase epitaxy,”
Journal of Applied Physics 118, 085301 (2015). Jena, and T. Luo, “Anisotropic thermal conductivity
in single crystal β-gallium oxide,” Applied Physics Letters 106, 111909
(2015). Luo, “Anisotropic thermal conductivity
in single crystal β-gallium oxide,” Applied Physics Letters 106, 111909
(2015). Jezowski, P. Grzegory, and B. Danilchenko, “Thermal conductivity of bulk GaN single crystals,” Physica B: Condensed Matter 329-333, 1531–1532 (2003). Shen, “A neuroevolution potential for predicting the thermal
conductivity of α, β, and ε-Ga2O3,” Applied Physics Letters 123, 192202
(2023). Yang, “Influence of polymorphism on the lattice thermal
conductivity of Ga2O3,” Journal of Vacuum Science & Technology A 42
(2024), 10. Several computational studies have reported the lattice thermal conductivity of κ-Ga2O3 along the (001) direction, which ranges from 1 to 4 W/m·K. 22–25 Xiao et al. Gucmann, and C. Yuan, “Phase- ˇ
Dependent Phonon Heat Transport in Nanoscale Gallium Oxide Thin
Films,” Small 20, 2309961 (2024). Sun, “Dissimilar
thermal transport properties in κ-Ga2O3 and β-Ga2O3 revealed by homogeneous nonequilibrium molecular dynamics simulations using machinelearned potentials,” Journal of Applied Physics 135, 065104 (2024). Girolami, M. Sun, “Dissimilar
thermal transport properties in κ-Ga2O3 and β-Ga2O3 revealed by homogeneous nonequilibrium molecular dynamics simulations using machinelearned potentials,” Journal of Applied Physics 135, 065104 (2024). Girolami, M. Trucchi, and R. Fornari, “Structural and Photoelectronic Properties of κ-Ga2O3 Thin Films Grown on Polycrystalline
Diamond Substrates,” Materials 17, 519 (2024). Trucchi, and R. Fornari, “Structural and Photoelectronic Properties of κ-Ga2O3 Thin Films Grown on Polycrystalline
Diamond Substrates,” Materials 17, 519 (2024). Hao, and X. Wang, “Efficient thermal
dissipation in wafer-scale heterogeneous integration of single-crystalline βGa2O3 thin film on SiC,” Fundamental Research 1, 691–696 (2021). Hao, and X. Wang, “Efficient thermal
dissipation in wafer-scale heterogeneous integration of single-crystalline βGa2O3 thin film on SiC,” Fundamental Research 1, 691–696 (2021). Foley, and S. Choi, “Ga2O3-
on-SiC Composite Wafer for Thermal Management of Ultrawide Bandgap
Electronics,” ACS Applied Materials & Interfaces 13, 40817–40829 (2021). Choi, “Ga2O3-
on-SiC Composite Wafer for Thermal Management of Ultrawide Bandgap
Electronics,” ACS Applied Materials & Interfaces 13, 40817–40829 (2021). Chatterjee, K. Singisetti, and S. Choi,
“Device-Level Thermal Management of Gallium Oxide Field-Effect Transistors,” IEEE Transactions on Components, Packaging and Manufacturing
Technology 9, 2352–2365 (2019). Averback, “Thermal conductance
of metal-metal interfaces,” Physical Review B 72, 245426 (2005). Ribeiro Da Silva, F. Averback, “Thermal conductance
of metal-metal interfaces,” Physical Review B 72, 245426 (2005). Ribeiro Da Silva, F. Davis, and
L. Porter, “Layered phase composition and microstructure of κ-Ga2O3-
dominant heteroepitaxial films grown via MOCVD,” Journal of Applied
Physics 131, 055305 (2022). Fornari, “The real structure of ε-Ga2O3 and its
relation to κ-phase,” CrystEngComm 19, 1509–1516 (2017). Gundrum, D. Cahill, and R. Averback, “Thermal conductance
of metal-metal interfaces,” Physical Review B 72, 245426 (2005). Nazaré De Freitas, and
M. Marques, “Phonons and thermal properties of α-, β-, δ-, and κ-Ga2O3
polymorphs from first principles studies,” Journal of Vacuum Science &
Technology A 43, 042805 (2025). Marques, “Phonons and thermal properties of α-, β-, δ-, and κ-Ga2O3
polymorphs from first principles studies,” Journal of Vacuum Science &
Technology A 43, 042805 (2025). Playford, A. Barney, and R. Walton, “Structures of Uncharacterised Polymorphs of Gallium Oxide from Total Neutron
Diffraction,” Chemistry – A European Journal 19, 2803–2813 (2013). Foley, and S. Choi, “Ga2O3-
on-SiC Composite Wafer for Thermal Management of Ultrawide Bandgap
Electronics,” ACS Applied Materials & Interfaces 13, 40817–40829 (2021). Foley, and S. Choi, “Ga2O3-
on-SiC Composite Wafer for Thermal Management of Ultrawide Bandgap
Electronics,” ACS Applied Materials & Interfaces 13, 40817–40829 (2021). The authors acknowledge the
use of the Bertucci Nanotechnology Laboratory at Carnegie
Mellon University supported by grant BNL-78657879 and use
of the Materials Characterization Facility at Carnegie Mellon University supported by grant MCF-677785. The authors
thank Jinkyu Kim for performing the AFM imaging and surface morphology characterization.Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the gains come from
The calculated thermal conductivities are, on average, 12% lower than the calculations This discrepancy likely results from internal defects and/or the thin transition layer that contains other Ga2O3 phases, which introduce additional phonon scattering The weak size dependence observed in the thermal conductivity of κ-Ga2O3 is attributed to its intrinsically short phonon MFPs This behavior arises from the complex crystal structure of the κ phase, which exhibits more distorted Ga-O polyhedra and a broader distribution of Ga-O bond lengths, lowering the average bond stiffness and reducing phonon group velocities
Thermal Management Implications
The low thermal conductivity of κ-Ga2O3 can be complemented by growing it on high thermal conductivity polycrystalline diamond or SiC substrates The junction temperature of Ga2O3-based devices can reach up to 200 ◦C where the thermal conductivity of κ-Ga2O3 is further reduced, highlighting a challenge for effective thermal management These findings highlight the need for alternative thermal management strategies, such as integration with high thermal conductivity substrates (e.g.
Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.
Improvements for AI systems
-
System can predict cross-plane thermal conductivity of kappa Ga2O3 thin films based on thickness and temperature by using first-principles calculations that include phonon-phonon and phonon-boundary scattering, matching experimental trends within uncertainties.
-
The system can assess the suitability of κ-Ga2O3 for heat dissipation in electronic devices by comparing its median crossplane thermal conductivity values to other experimentally measured Ga2O3 polymorphs at comparable thicknesses, identifying where it exhibits the lowest thermal conductivity.
-
The AI system can predict the temperature dependence of κ-Ga2O3 thermal conductivity between 293 and 400 K, specifically noting that
the thinner film exhibiting a weaker temperature dependence due to increased phonon-boundary scattering
compared toa moderate decrease in kκ-Ga2O3 due to enhanced phonon-phonon scattering.
-
The system can determine the need for alternative thermal management strategies by identifying that the
low thermal conductivity of κ-Ga2O3 can be complemented by growing it on high thermal conductivity polycrystalline diamond or SiC substrates.
Abstract
The thermal conductivities of (001) κ-Ga 2 O 3 thin films deposited on c-plane sapphire substrates were measured with frequency-domain thermoreflectance (FDTR). The thermal conductivity increases from 1.83+0.19-0.18 W/m times K to 2.26+0.35-0.40 W/m times K as the thicknesses increase from 159 nm to 689 nm. This weak thickness dependence indicates that the majority of the intrinsic phonon mean free paths are smaller than the range of investigated film thicknesses. First-principles-based calculations that include phonon-phonon and phonon-boundary scattering capture this size-dependent behavior and support our experimental observation. Temperature-dependent measurements of a 689 nm film from 293 to 400 K show a decrease in thermal conductivity with increasing temperature due to enhanced phonon-phonon scattering. A weaker temperature dependence is observed in a 159 nm film where phonon-boundary scattering becomes more prominent. At comparable film thicknesses, our measured κ-Ga 2 O 3 films exhibit lower values of cross-plane thermal conductivity than the other experimentally measured Ga 2 O 3 polymorphs. Our experimental observations are supported by prior predictions, which suggest that the low thermal conductivity of κ-Ga 2 O 3 results from its complex crystal structure, which leads to increased anharmonicity and lower phonon group velocities relative to other polymorphs. Thermal management strategies, such as integration with high-thermal-conductivity substrates, may thus be required to mitigate self-heating for κ-Ga 2 O 3-based electronic devices.
Related papers
- Structural contribution to light-induced gap suppression in Ta 2 NiSe 5
- Anatomy of fast current-induced skyrmion motion in synthetic antiferromagnets
- Magnetic control of an exciton-polariton condensate in a van der Waals magnet
- High-pressure elastic properties of GeO2 polymorphs up to 120 GPa
- Decoupling Strain-Rate Sensitivity and Deformation Length Scale Effects in Neutron-Irradiated Tungsten: A Coupled Nano-Indentation, HR-EBSD and Crystal Plasticity Study
- Magnetism modulation in Co3Sn2S2 by current-assisted domain wall motion