Low-cost, ultra-wideband, differential low-noise amplifier for interferometric radio telescopes

arXiv:2607.21715 · astro-ph.IM · Submitted 2026-07-23 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Astrophysics. The day in astrophysics: observations, models and what the data forces.

Vera: We're looking at the paper: "Low-cost, ultra-wideband, differential low-noise amplifier for interferometric radio telescopes".

Title and authors: Vera: Now let's look at what the title actually tells us about this piece of work, "Low-cost, ultra-wideband, differential low-noise amplifier for interferometric radio telescopes." It sets expectations right from the start.

Jocelyn: I think it immediately signals that the focus is on affordability and broad frequency coverage simultaneously. Ultra wideband means it’s meant to handle a huge range of frequencies at once, and low cost means it’s practical for deploying many of these things.

Subrahmanyan: It tells me the primary function here is to provide a differential low noise amplifier specifically tailored for interferometric radio telescopes, which are used to measure very fine details in the structure of the universe.

Vera: Right, so we're talking about a dual polarized device that’s cheap and covers a wide swath of frequencies while keeping noise down. It sounds like they are tackling some big hardware hurdle for next generation arrays.

Jocelyn: And it also mentions eliminating the need for a pre amplification balun, which is this extra piece of electronics you usually have to put in between your signal and your amplifier. That’s a real simplification in the design process.

The paper's summary: Vera: So, let's go over what the authors summarize here about this differential low noise amplifier for interferometric radio telescopes. They are describing the core concept of how they built this and what it achieves in practice.

Jocelyn: They explain that they used a multi stage architecture, starting with a Qorvo QPL9547 as the first stage, which is inherently a single ended device, but they configure two of them to create that dual polarized differential pair.

Subrahmanyan: So they are taking a single end device and cleverly arranging it to handle both polarities of the input signal independently, which is smart engineering if you’re working with differential data.

Vera: And the physical size is compact, measuring five centimeters by five centimeters by three centimeters, which is really impressive for something that needs to be manufactured in large quantities.

Jocelyn: They also detail how they matched it to a tapered slot Vivaldi feed with an input impedance of approximately one hundred ten ohms over a bandwidth spanning three hundred to fifteen hundred megahertz. That gives us the practical context for what this amplifier is designed to interface with.

The paper's improvements: Vera: The paper points out several ways they improved the design, which is where we get into how this specific LNA design gets better than just a standard single ended one.

Jocelyn: One big improvement is the move to a dual polarized differential topology using commercially available surface mount components, which directly addresses the cost and scalability goals of the design.

Subrahmanyan: From a theory perspective, they’ve shown that because you have two branches amplifying one polarity each, the total power or effective temperature of this differential system ends up being the same as a single ended version.

Vera: That's an important conceptual point. It means you can think of each branch as taking about half the voltage of a single ended signal in terms of noise contribution, which is a nice way to frame the trade-off for engineers.

Jocelyn: They also highlighted how they managed the bandwidth limitation that sometimes comes with these kinds of designs, noting that while their amplifiers support operation up to six gigahertz, the output balun specification only goes up to four gigahertz.

Conclusion: Vera: So we’ve seen how this low cost design and its dual polarized nature give us a practical front end for large N radio telescopes that avoids the need for a pre amplification balun. It seems like they’ve successfully combined high performance with commercial component availability.

Jocelyn: The result is a system noise temperature as low as twenty five Kelvin when matched to that Vivaldi feed operating across three hundred to fifteen hundred megahertz. That's a solid number for an ultra wideband instrument.

Subrahmanyan: For cosmology, this sort of low noise performance at these frequencies means we can get cleaner signals from the arrays, which is crucial for constraining parameters related to large scale structure formation.

Vera: It’s definitely a practical solution demonstrating that high performance differential front end electronics can be realized using low cost commercial components, which is a big deal for deploying new hardware.

Jocelyn: So we wrap up on this paper about the low-cost, ultra wideband, differential low noise amplifier for interferometric radio telescopes. It shows a path forward for building more accessible and capable radio astronomy receivers.

Department of Astronomy and Astrophysics, University of Toronto · Dunlap Institute of Astronomy and Astrophysics, University of Toronto

astro-ph.IM

Submitted: 2026-07-23

Updated: 2026-07-23

Comments: Presented at SPIE Astronomical Telescopes and Instrumentation 2026; To appear in SPIE Proceedings

Journal ref: Proceedings of the SPIE, Volume 14153, id. 141531T (2026)

DOI: 10.1117/12.3102644

License: http://arxiv.org/licenses/nonexclusive-distrib/1.0/

Importance score: 74/100

The gist: Low-cost, ultra-wideband, dual-polarized differential low-noise amplifier for interferometric radio telescopes is a design that eliminates the need for a pre-amplification balun and costs…

Key concepts

Differential Topology
The amplifier uses two identical branches that amplify opposite polarities of the input signal independently. This technique helps reject common noise signals while preserving the desired differential information. It is a core feature of the design, allowing for better signal integrity in sensitive radio astronomy applications.
System Noise Temperature (T_sys)
This measurement quantifies the total noise power observed at the receiver, including amplifier noise and any other sources. The paper shows that by matching the amplifier to a Vivaldi feed over 300–1500 MHz, they achieved very low system noise temperatures of 25 K, which is crucial for sensitive radio astronomy.
Low-Cost Implementation
The design prioritizes affordability and scalability by exclusively using commercially available surface-mount components and standard PCBs. This approach makes the LNA accessible for mass production in large radio telescope projects without requiring expensive custom or specialized parts.

Terminology

Summary

Low-cost, ultra-wideband, dual-polarized differential low-noise amplifier for interferometric radio telescopes is a design that eliminates the need for a pre-amplification balun and costs approximately 20 USD per unit The amplifier demonstrates a noise figure close to 0. p. 03 dB across a 10:1 bandwidth when matched to a constant 130 Ω source, while feedcoupled measurements yield system noise temperatures as low as 25 K when matched to a Vivaldi feed operating over a 300–1500 MHz bandwidth

Design Objectives and Implementation

The primary objective of the LNA design was to provide a low-cost differential front-end suitable for integration with modern ultra-wideband radio astronomy feeds Key design requirements included affordability and scalability, achieved by implementing the design exclusively using commercially available surface-mount components and standard low-cost printed circuit board (PCB) substrates The LNA employs a multi-stage architecture with a Qorvo QPL9547 serving as the first stage, resulting in a compact design measuring 5 cm × 5 cm × 3 cm

Differential Topology and Architecture

The LNA prototype employs commercially available single-ended surface-mount components arranged in a differential topology consisting of two identical amplifier branches Each branch independently amplifies one polarity of the differential input signal with respect to a common ground The bandwidth of the prototype is primarily limited by the output balun which is specified for operation up to 4 GHz, although active amplifier stages support operation to approximately 6 GHz

Performance Characterization

The LNA was characterized through laboratory gain and noise measurements together with feed-coupled hot-cold testing at the Dominion Radio Astrophysical Observatory The LNA achieves a minimum noise temperature of 17 K at 900 MHz when presented with an optimum differential source impedance of 135 Ω Feed-coupled measurements yield system noise temperatures as low as 25 K when matched to a Vivaldi feed operating over a 300–1500 MHz bandwidth

System Analysis and Conclusion

The total power (or effective temperature) of a differential system with parallel LNAs is the same as a single-ended version This result means that each polarity or ”branch” of the differential signal can be represented as 1/√2 of the single-ended signal in voltage space The design provides a practical and scalable front-end solution for next-generation large-N radio telescopes This work demonstrates that high-performance differential front-end electronics can be realized using low-cost commercial components

References

[1] Hallinan, G., Ravi, V., Weinreb, S., Kocz, J., Huang, Y., Woody, D. P., Lamb, J., D’Addario, L., Catha, M., Shi, J., Law, C., Kulkarni, S. R., Phinney, E. S., Eastwood, M. W., Bouman, K. L., McLaughlin, M. A., Ransom, S. M., Siemens, X., Cordes, J. M., Lynch, R. S., Kaplan, D. L., Chatterjee, S., Lazio, J., Brazier, A., Bhatnagar, S., Myers, S. T., Walter, F.: The dsa-2000 – a radio survey camera (2019). p. 0

[2] Vanderlinde, K., Liu, A., Gaensler, B., Bond, D., Hinshaw, G., Ng, C., Chiang, C., Stairs, I., Brown, J. p. 3-A., Sievers, J., Mena-J.: The Canadian Hydrogen Observatory and Radio-transient Detector (CHORD), in [Canadian Long Range Plan for Astronomy and Astrophysics White Papers], 2020. p. 9

[3] Dewdney, P. E., Hall, P. J., Schilizzi, R. T., Lazio, T. J. L.: The square kilometre array Proceedings of the IEEE 97(8), 1482–1496 (2009). p. 9

[4] Cappallo, R. C., Rogers, A. E. E., Lonsdale, C. J., Bowman, J. D., Barrett, J. P., Murray, S. G.: Edges-3: Instrument design and commissioning Publications of the Astronomical Society of the Pacific 137(12), 125002 (2025). p. 4

[5] Bhaumik, S. and George, D. p. 0: Reviw of Square Kilometre Array LNA Technologies and Topologies in [Wide Field Astronomy and Technology for the Square Kilometre Array], 46 (Jan. p. 0 2009).

[6] Lau, A. W. K., Vanderlinde, K., Mena-Parra, J., Lansdale, C.: Developing a low-cost, compact radioover-fiber (rfof) linkage for radio telescope arrays in [Ground-based and Airborne Instrumentation for Astronomy X], 13096 (2024). p. 9

[7] Garcia Perez, O., Segovia-Vargas, D., Garcia-Munoz, L., Jimenez-Martin, J., Gonzalez: Broadband differential low-noise amplifier for active differential arrays in Microwave Theory and Techniques, IEEE Transactions on 59 (02 2011). p. 0

[8] Jimenez-Martin, J. L., Gonzalez-Posadas, V., Parra-Cerrada, A., Garcia-Munoz, L. E., Segovia-Vargas, D.: Broadband (1-16 ghz) balanced mmic gaas phemt lna for radio astronomy applications in [2019 European Microwave Conference in Central Europe (EuMCE)], 91–94 (2019). p. 0

[9] Tan, G. H. and Rohner, C. H.: Low-frequency array active-antenna system in [Radio Telescopes], Butcher, H. p. 9 R., ed., Society of Photo-Optical Instrumentation Engineers (SPIE) Conference Series 4015 (July 2000). p. 9

[10] Sutinjo, A. T., Colegate, T. M., Wayth, R. B., Hall, P. J.: Characterization of a Low-Frequency Radio Astronomy Prototype Array in Western Australia IEEE Transactions on Antennas and Propagation 63 (Dec. p. 9 2015).

[11] Ellingson, S. W., Taylor, G. B., Craig, J., Hartman, J., Dowell, J.: The lwa1 radio telescope IEEE Transactions on Antennas and Propagation 61(5), 2540–2549 (2013). p. 0

[12] Mackay, V., Lai, M., Shmerko, P., Wulf, D., Belostotski, L., Vanderlinde, K.: Low-Cost, Low-Loss, Ultra-Wideband Compact Feed for Interferometric Radio Telescopes Journal of Astronomical Instrumentation 12 (Jan. p. 0 2023).

[13] Fan, T.-H., Chiong, C.-C., Wang, H.: A 3.3 to 11.3 ghz differential lna with slight imbalance active balun in 0. p. 115-um gaas phemt process for radio astronomical receiver in [2021 16th European Microwave Integrated Circuits Conference (EuMIC)], 91–94 (2022).

[14] Hu, X., Zhao, C., Tian, J., Tang, W., Zhang, G.: Impact of ground via placement and size in grounded coplanar waveguide interconnects in [2024 IEEE International Workshop on Radio Frequency and Antenna Technologies], 38–40 (2024). p. 2

[15] Hovey, G. J., Messing, R., Willis, A. G., Veidt, B.: An automated system for measurement of sensitive microwave radiometers in [2018 18th International Symposium on Antenna Technology and Applied Electromagnetics (ANTEM)], 1–2 (2018).

[16] Lin, J. and Vanderlinde, K.: Design, systems integration and validation of focus electronics for the canadian hydrogen observatory and radio-transient detector in [Astronomical Telescopes + Instrumentation], SPIE (2026). p. 9

[17] Lau, A. W. K., Allder, V., Costa, S. p. 0 D., Hum, S., Vanderlinde, K.: Active planar antenna design for charts array in [2025 International Symposium on Antennas and Propagation (ISAP)], 1–2 (2025). p. 9

[18] Cassanelli, T., Mena-Parra, J., Manosalva, S., Lau, A. W. K., Gallardo, D., Vanderlinde, K.: Canadian-chilean array for radio transient studies (charts): Analog system developments in [2025 19th European Conference on Antennas and Propagation (EuCAP)], 1–5 (2025). p. 9

[19] The paper is titled Low-cost, ultra-wideband, differential low-noise amplifier for interferometric radio telescopes arXiv:2607.21715v1 [astro-ph. p. 0IM] 23 Jul 2026. p. 0

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improve large-N radio telescope receivers by integrating low-cost dual-polarized differential LNAs directly with Vivaldi feeds, eliminating the need for a pre-amplification balun which can increase the system noise temperature, limit the achievable bandwidth, and introduce cross-talk between dual-polarized channels. This allows for a low-cost, ultra-wideband solution built from commercial components.

  2. Enhance receiver design robustness by implementing a multi-stage architecture using a Qorvo QPL9547 as the first stage to achieve a minimum noise temperature of 17 K at 900 MHz when matched to an optimum differential source impedance of 135 ohms. This compact design, measuring 5 cm x 5 cm x 3 cm, facilitates mass production for large-scale deployments.

  3. Increase the reliability and performance of differential systems by quantifying the impact of component tolerances on signal quality using the Signal to Noise Ratio (SNR) degradation derived as a function of gain and phase imbalance, as summarized in Figure 3. This allows engineers to predict the tolerance of the topology to realistic amplifier mismatches.

  4. Optimize noise performance across ultra-wideband frequencies by demonstrating that The remainder of this paper is organized as follows. Section 2 describes the LNA topology, physical implementation, and the measurement procedures used to characterize its gain and noise performance, leading to measured system noise temperatures as low as 25 K when matched to a Vivaldi feed operating over a 300–1500 MHz bandwidth.

  5. Validate differential amplifier performance under realistic operational conditions by performing hot-cold testing at the Dominion Radio Astrophysical Observatory, where measurements show that the measured system noise temperature reaches a minimum of approximately 25 K and remains below 40 K over the majority of the operating band. This provides empirical validation for deployment readiness.

Related papers