First Thin-Film Lithium Tantalate Polarization Controller Enabling Reset-Free Mrad/s Tracking for Optical Interconnects

arXiv:2601.03652 · physics.optics · Submitted 2026-01-07 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: We're looking at the paper: "First Thin-Film Lithium Tantalate Polarization Controller Enabling Reset-Free Mrad/s Tracking for Optical Interconnects".

Mira: Here's the gist of the paper. The first integrated polarization controller based on thin-film lithium tantalate enables reset-free polarization tracking at Mrad·s−1 speeds This work establishes TFLT as a new platform for ultrafast, low-power, reset-free, and drift-free polarization control in coherent optical interconnects and beyond System Motivation The rapid escalation of computing power driven by large-scale artificial intelligence is placing unprecedented demands on the bandwidth, latency, and energy efficiency of data-center interconnects (DCIs) Self-homodyne coherent (SHC) transmission is a promising architecture because it preserves the spectral efficiency of coherent detection while greatly simplifying digital signal processing, but its practical deployment is critically limited by random and often ultrafast state-of-polarization (SOP) fluctuations that induce carrier fading and destabilize coherent reception In an SHC receiver, coherent demodulation requires stable alignment between the SOP of the signal and that of the transmitted carrier Extreme transient events such as lightning strikes, power switching, or strong electromagnetic interference coupling into fiber spans can drive polarization dynamics into the hundreds of krad·s−1 or even the Mrad·s−1 regime Such ultrafast excursions lie far beyond the tracking capability of existing integrated polarization controllers and represent a worst-case but realistic threat to the stability of SHC links Device Architecture and Performance The device is based on three fundamental building blocks: edge couplers (EC), a polarization splitter-rotator (PSR), and 2×2 Mach-Zehnder interferometers (MZI) The TFLT APC exhibits polarization-dependent loss (PDL) below 0.3 dB, a half-wave voltage below 2.5 V, high modulation bandwidth, and negligible DC drift The device achieves polarization-tracking speeds up to 2 Mrad·s−1 for transient polarization disturbances and stable reset-free operation under continuous polarization disturbances is maintained up to 1 Mrad·s−1 The on-chip insertion loss of the complete four-stage APC is below 4 dB within a compact footprint of 1.4 cm × 1.3 mm Algorithmic Innovation To accommodate the finite tuning range of integrated phase shifters, a finite-boundary gradient-descent (FBGD) control algorithm is developed that ensures reset-free SOP evolution with no phase jump The core idea is to introduce a boundaryaware regularization term into the feedback loss function, which actively and cooperatively adjusts the voltages of the four cascaded phase shifters This approach prevents any individual stage from reaching the limits of its tuning range, achieving long-term, stable, and continuous SOP tracking The resulting loss function is written as (2) where  is the DACs’ output voltage vector and P() is the measured feedback optical power Experimental Validation The APC is validated through both standalone polarization-tracking measurements and a dual-polarization 16-QAM SHC 400-Gbps transmission system For scrambling speeds up to 2 Mrad·s−1, the relative intensity error (RIE) remains well below the lock-loss threshold, with 99.9% of samples below 0.3 and the average RIE is below 0.08 For scrambling speeds up to 1 Mrad·s−1, the RIE remains well below the lock-loss threshold, with 99.9% of samples below 0.2, and a maximum value below 0.4 When the scrambling speed is increased to 2 Mrad·s−1, the BER rises above the FEC threshold, marking the onset of system-level failure The central result of this work is not merely a high polarization tracking speed, but the demonstration of continuous, reset-free operation in the megaradian-per-second regime on an integrated photonic platform The observed performance boundary is shown to arise from finite control-loop latency rather than intrinsic photonic limitations This confirms that the proposed TFLT–FBGD scheme remains fully effective across the entire dynamic range relevant to data-center and short-reach optical interconnects The work establishes TFLT as a key enabler for next-generation optical interconnects in AI-driven data centers and short-reach communication networks Real-time polarization tracking was implemented on an FPGA, providing the deterministic latency and computational throughput required for high-speed feedback control The system architecture integrates multi-channel analog-to-digital converters (ADCs) and digital-to-analog converters (DACs) with dedicated analog front-end and back-end circuitry Sufficient resolution is required to preserve sensitivity to small SOP deviations and to enable fine-grained polarization adjustment without quantization noise limiting the effective extinction ratio of the polarization-control elements The total loop latency, including ADC, DAC, peripheral circuitry, and algorithmic processing, is approximately 100 ns Reference The reference list includes several works on polarization control in silicon photonics and lithium niobate platforms Specifically, studies cover aspects like the intrinsic thermal response limiting tracking speed in silicon photonic platforms and the development of high-performance polarization management devices based on thin-film lithium niobate.

Kai: The paper also references literature concerning self-homodyne coherent systems and dual-polarization intensity modulation (DP-IMDD) architectures for data center connectivity and polarization control in general.

Mira: It also cites foundational work on polarization control in coherent communications and experimental measurements of SOP transients due to lightning strikes.

Kai: Acknowledgements This work is supported by the National Key Research and Development Program of China (No.

Paper summary: Kai: So to recap, this paper is about creating the first integrated polarization controller using thin film lithium tantalate that can track polarization at Mrad per second speeds without needing a reset.

Mira: The thesis is that they prove this platform works by showing it handles those extreme transient events and maintains stable reset free operation even when there's continuous polarization disturbance up to one Mrad per second.

Lev: From my perspective, the main hurdle I see is that running this on actual hardware means we have to deal with the latency of that control loop, which they mention is about one hundred nanoseconds.

Kai: Exactly. And they show that their method involves a finite boundary gradient descent algorithm to ensure reset free SOP evolution with no phase jump by introducing a boundary aware regularization term into the feedback loss function.

Mira: And they validated this by scrambling speeds up to two Mrad per second, where the relative intensity error stays below zero point three for most samples, and below zero point four when scrambling at one Mrad per second.

Lev: But I'm thinking about the implications for real hardware: we need to make sure that this level of stability translates into a usable bit error rate under realistic data center conditions.

Kai: The paper says that when they increase the scrambling speed to two Mrad per second, the bit error rate goes above the FEC threshold which is where you start seeing system level failure.

Mira: So they’re saying this platform can handle polarization scrambles at those high rates, but there are still limits imposed by that control loop latency of one hundred nanoseconds.

Lev: That means our hardware design needs to account for that latency because if we want to push the scrambling speed even higher, we're hitting a wall on the feedback time.

Kai: So what they’re really showing is that the performance boundary isn't set by some intrinsic photonic limitation of the material itself.

Mira: It comes from finite control loop latency instead, which is a much more actionable piece of information for designers than just material properties alone.

Conclusion: Kai: So, looking at the title, this whole thing is about pushing past what we thought was possible with integrated polarization control.

Mira: It really shows that thin film lithium tantalate can be a new way to manage polarization for data center interconnects and short reach communication networks.

Lev: For real hardware running this, we need to think about how the architecture integrates this APC into a larger system without introducing too much noise or power overhead.

Kai: The authors are showing that they built something compact, with an on chip insertion loss below four decibels in one point four centimeter by one point three millimeter.

Mira: So the real implication is that we have a low power, reset free and drift free solution now for polarization control in these high bandwidth optical links.

Lev: It means that for the future, instead of worrying about massive external disturbances causing link outages, we can focus on building more robust transmission links because this paper shows how to manage the internal polarization dynamics.

Zichao Gao, Siyu Lu, Mingming Zhang, Gengqi Yao, Chicheng Zhang, Miao Deng, Siyu Chen, Yiqi Dai, Shiqi Yue, Chijun Li, Yuqi Li, Ziwen Zhou, Zheli Liu

School of Optical and Electronic Information and Wuhan National Laboratory for Optoelectronics, Huazhong University of Science and Technology, Wuhan 430074, China · Hubei Optical Fundamental Research Centre, Wuhan 430074, China

physics.optics

Submitted: 2026-01-07

Updated: 2026-01-07

Comments: 27 pages, 8 figures

Journal ref: Nature Communications, 2026

DOI: 10.1038/s41467-026-75732-z

License: http://creativecommons.org/licenses/by-nc-nd/4.0/

Importance score: 89/100

The gist: The first integrated polarization controller based on thin-film lithium tantalate enables reset-free polarization tracking at Mrad·s−1 speeds This work establishes TFLT as a new platform for…

Key concepts

Self-homodyne coherent (SHC) transmission
This is an optical transmission method that uses the same light source to transmit and receive signals. It simplifies digital signal processing but requires stable alignment between the signal's polarization and the carrier's polarization to work correctly. Fluctuations in this alignment cause problems.
Polarization Tracking Speed (Mrad·s⁻¹)
This measures how fast a device can correct changes in the light's polarization. The paper shows this controller can track disturbances up to 2 Mrad·s⁻¹. This speed is necessary to handle sudden, extreme polarization shifts that occur in real-world scenarios like lightning strikes.
Finite-Boundary Gradient-Descent (FBGD) Control
This is a specific control algorithm designed to manage the limitations of integrated phase shifters. It introduces a special term into the feedback loss function to actively adjust all four phase shifters cooperatively, ensuring continuous tracking without any single stage hitting its tuning limit.
Reset-free Operation
In traditional systems, polarization controllers might need a reset to start tracking again after a large disturbance. This new controller can maintain stable polarization tracking continuously without needing resets, which is vital for reliable data center links.

Terminology

Summary

The first integrated polarization controller based on thin-film lithium tantalate enables reset-free polarization tracking at Mrad·s−1 speeds This work establishes TFLT as a new platform for ultrafast, low-power, reset-free, and drift-free polarization control in coherent optical interconnects and beyond

System Motivation

The rapid escalation of computing power driven by large-scale artificial intelligence is placing unprecedented demands on the bandwidth, latency, and energy efficiency of data-center interconnects (DCIs) Self-homodyne coherent (SHC) transmission is a promising architecture because it preserves the spectral efficiency of coherent detection while greatly simplifying digital signal processing, but its practical deployment is critically limited by random and often ultrafast state-of-polarization (SOP) fluctuations that induce carrier fading and destabilize coherent reception In an SHC receiver, coherent demodulation requires stable alignment between the SOP of the signal and that of the transmitted carrier Extreme transient events such as lightning strikes, power switching, or strong electromagnetic interference coupling into fiber spans can drive polarization dynamics into the hundreds of krad·s−1 or even the Mrad·s−1 regime Such ultrafast excursions lie far beyond the tracking capability of existing integrated polarization controllers and represent a worst-case but realistic threat to the stability of SHC links

Device Architecture and Performance

The device is based on three fundamental building blocks: edge couplers (EC), a polarization splitter-rotator (PSR), and 2×2 Mach-Zehnder interferometers (MZI) The TFLT APC exhibits polarization-dependent loss (PDL) below 0.3 dB, a half-wave voltage below 2. p. 0

Where the paper says it

The four-stage electro-optic device exhibits polarization-dependent loss (PDL) below 0. 3 dB, a half-wave voltage below 2.

5 V, high modulation bandwidth, and negligible DC drift The device achieves polarization-tracking speeds up to 2 Mrad·s−1 for transient polarization disturbances and stable reset-free operation under continuous polarization disturbances is maintained up to 1 Mrad·s−1 The on-chip insertion loss of the complete four-stage APC is below 4 dB within a compact footprint of 1. p. 3
Where the paper says it

Our device achieves polarization-tracking speeds up to 2 Mrad·s⁻¹ for transient polarization disturbances and stable reset-free operation under continuous polarization disturbances is maintained up to 1 Mrad·s⁻¹, representing the fastest integrated polarization tracking reported to date and covering virtually all polarization dynamics encountered in practical fiber links, from slow environmental drifts to extreme, lightning-scale perturbations, while preserving stable coherent reception throughout. By simultaneously delivering ultrafast response, low polarization-dependent loss (PDL), low driving voltage, and drift-free operation, this work establishes a new regime of polarization control, within which multiple key performance metrics extend beyond the current state of the art, unlocking the practical scalability of both SHC and DP-IMDD optical interconnects for next-generation AI-driven data-center networks.

4 cm × 1.3 mm

Algorithmic Innovation

To accommodate the finite tuning range of integrated phase shifters, a finite-boundary gradient-descent (FBGD) control algorithm is developed that ensures reset-free SOP evolution with no phase jump The core idea is to introduce a boundaryaware regularization term into the feedback loss function, which actively and cooperatively adjusts the voltages of the four cascaded phase shifters This approach prevents any individual stage from reaching the limits of its tuning range, achieving long-term, stable, and continuous SOP tracking The resulting loss function is written as (2) where  is the DACs’ output voltage vector and P() is the measured feedback optical power

Experimental Validation

The APC is validated through both standalone polarization-tracking measurements and a dual-polarization 16-QAM SHC 400-Gbps transmission system For scrambling speeds up to 2 Mrad·s−1, the relative intensity error (RIE) remains well below the lock-loss threshold, with 99.9% of samples below 0.3 and the average RIE is below 0.08 For scrambling speeds up to 1 Mrad·s−1, the RIE remains well below the lock-loss threshold, with 99. p. 1

Where the paper says it

be tracked at speeds up to 2 Mrad·s⁻¹, while stable reset-free operation under continuous polarization disturbances is maintained up to 1 Mrad·s⁻¹. This reset-free performance represents more than doubling the state of the art, while the pre-FEC bit-error rates remain below the HD-FEC threshold under realistic DCI conditions and lightning-scale polarization disturbances.

9% of samples below 0.2, and a maximum value below 0.4 When the scrambling speed is increased to 2 Mrad·s−1, the BER rises above the FEC threshold, marking the onset of system-level failure

Conclusion and Impact

The central result of this work is not merely a high polarization tracking speed, but the demonstration of continuous, reset-free operation in the megaradian-per-second regime on an integrated photonic platform The observed performance boundary is shown to arise from finite control-loop latency rather than intrinsic photonic limitations This confirms that the proposed TFLT–FBGD scheme remains fully effective across the entire dynamic range relevant to data-center and short-reach optical interconnects The work establishes TFLT as a key enabler for next-generation optical interconnects in AI-driven data centers and short-reach communication networks

Methods

Real-time polarization tracking was implemented on an FPGA, providing the deterministic latency and computational throughput required for high-speed feedback control The system architecture integrates multi-channel analog-to-digital converters (ADCs) and digital-to-analog converters (DACs) with dedicated analog front-end and back-end circuitry Sufficient resolution is required to preserve sensitivity to small SOP deviations and to enable fine-grained polarization adjustment without quantization noise limiting the effective extinction ratio of the polarization-control elements The total loop latency, including ADC, DAC, peripheral circuitry, and algorithmic processing, is approximately 100 ns

Reference

The reference list includes several works on polarization control in silicon photonics and lithium niobate platforms Specifically, studies cover aspects like the intrinsic thermal response limiting tracking speed in silicon photonic platforms and the development of high-performance polarization management devices based on thin-film lithium niobate. The paper also references literature concerning self-homodyne coherent systems and dual-polarization intensity modulation (DP-IMDD) architectures for data center connectivity and polarization control in general. p. 2

Where the paper says it

Dual-polarization intensitymodulation and direct-detection (DP-IMDD) architectures, which are rapidly gaining traction as a low-cost solution for short-reach and data-center links 14,15 , likewise depend on stable and well-defined polarization states to preserve channel orthogonality and suppress inter-polarization crosstalk. In these systems, uncontrolled state-of-polarization (SOP) drift directly degrades signal integrity and limits the scalability of polarization-multiplexed IMDD, making fast and robust optical-domain polarization control a universal requirement across both coherent and direct-detection interconnects.

It also cites foundational work on polarization control in coherent communications and experimental measurements of SOP transients due to lightning strikes. p. 3
Where the paper says it

Our device achieves polarization-tracking speeds up to 2 Mrad·s⁻¹ for transient polarization disturbances and stable reset-free operation under continuous polarization disturbances is maintained up to 1 Mrad·s⁻¹, representing the fastest integrated polarization tracking reported to date and covering virtually all polarization dynamics encountered in practical fiber links, from slow environmental drifts to extreme, lightning-scale perturbations, while preserving stable coherent reception throughout. By simultaneously delivering ultrafast response, low polarization-dependent loss (PDL), low driving voltage, and drift-free operation, this work establishes a new regime of polarization control, within which multiple key performance metrics extend beyond the current state of the art, unlocking the practical scalability of both SHC and DP-IMDD optical interconnects for next-generation AI-driven data-center networks.

Acknowledgements

This work is supported by the National Key Research and Development Program of China (No. 2025YFA1212900) and other national funding sources Lithium tantalate device fabrication is performed at the cleanroom of Wuhan ANPI Corporation

Author Contributions

S.Y., C.Z., J.X., M.T., conceived and planned the research S. p. 0

Where the paper says it

First Thin-Film Lithium Tantalate Polarization Controller Enabling Reset-Free Mrad·s⁻¹ Tracking for Optical Interconnects Zichao Gao1,† , Siyu Lu1,† , Mingming Zhang1,† , Gengqi Yao1 , Chicheng Zhang1 , Miao Deng1 , Siyu Chen1 , Yiqi Dai1 , Shiqi Yue1 , Chijun Li1 , Yuqi Li1 , Ziwen Zhou1 , Zheli Liu1 , Xinyang Yu1 , Xitao Ji1 , Cheng Zeng1,*, Siqi Yan1,2,*, Jinsong Xia1,* and Ming Tang1,2,* 1 School of Optical and Electronic Information and Wuhan National Laboratory for Optoelectronics, Huazhong University of Science and Technology, Wuhan 430074, China 2 Hubei Optical Fundamental Research Centre, Wuhan 430074, China *Corresponding author: Cheng Zeng. Email: zengchengwuli@hust.

L. and G.Y. designed and fabricated the devices; Z. p. 9
Where the paper says it

1 Hz to 1 MHz are applied to a single APC stage, as shown in Figure 2f. The output transmission remains stable and fully repeatable over more than seven decades of modulation frequency, indicating negligible DC drift without the need for annealing , which is a critical advantage over most thin-film lithium-niobate devices with slow bias drift typically degrading polarization control25,28 .

G. designed and implemented the control system and realized the control algorithm proposed by M. p. 0
Where the paper says it

To accommodate the finite tuning range of integrated phase shifters, we develop a finite-boundary gradient-descent (FBGD) control algorithm that ensures reset-free SOP evolution with no phase jump. The implemented adaptive polarization controller (APC) is validated through both standalone polarization-tracking measurements and a dual-polarization 16-QAM SHC 400-Gbps transmission system.

Z.G., S.L., and G.Y. led the measurement and analysis with assistance from C. p. 7
Where the paper says it

This remarkably low PDL underscores the polarization-insensitive nature of both components. The PSR further provides an extinction ratio exceeding 20 dB over the full measurement range, ensuring efficient separation and recombination of orthogonal polarization components.

Competing Interests

The authors declare no competing interests Supplementary information is available online at https://doi.org/xxxxxx The paper is 2601.03652.

References

The references listed support the claims made throughout the text regarding polarization control and related technologies. Specifically, references cover topics such as self-homodyne coherent systems, dual-polarization IMDD systems, and specific device implementations like lithium niobate modulators. p. 1

Where the paper says it

Self-homodyne coherent (SHC) architectures have therefore emerged as an attractive alternative, preserving the capacity advantage of coherent detection while eliminating carrier recovery and dramatically simplifying signal processing6–8 . This architectural simplification, however, shifts a critical burden from the digital to the optical domain: SHC systems become intrinsically sensitive to polarization dynamics9 .

Additional Information

Supplementary information is available online at https://doi.org/xxxxxx The work is 2601. p. 0

Where the paper says it

Email: tangming@mail. cn † These authors contributed equally to this work.

p. 0
Where the paper says it

Email: tangming@mail. cn † These authors contributed equally to this work.

03652.

References (Full List)

The reference list includes several works on polarization control and related technologies, such as those by Singh et al., Kumar et al., Sun et al., Wade et al., Cheng et al. p. 0

Where the paper says it

First Thin-Film Lithium Tantalate Polarization Controller Enabling Reset-Free Mrad·s⁻¹ Tracking for Optical Interconnects Zichao Gao1,† , Siyu Lu1,† , Mingming Zhang1,† , Gengqi Yao1 , Chicheng Zhang1 , Miao Deng1 , Siyu Chen1 , Yiqi Dai1 , Shiqi Yue1 , Chijun Li1 , Yuqi Li1 , Ziwen Zhou1 , Zheli Liu1 , Xinyang Yu1 , Xitao Ji1 , Cheng Zeng1,*, Siqi Yan1,2,*, Jinsong Xia1,* and Ming Tang1,2,* 1 School of Optical and Electronic Information and Wuhan National Laboratory for Optoelectronics, Huazhong University of Science and Technology, Wuhan 430074, China 2 Hubei Optical Fundamental Research Centre, Wuhan 430074, China *Corresponding author: Cheng Zeng. Email: zengchengwuli@hust.

p. 0
Where the paper says it

First Thin-Film Lithium Tantalate Polarization Controller Enabling Reset-Free Mrad·s⁻¹ Tracking for Optical Interconnects Zichao Gao1,† , Siyu Lu1,† , Mingming Zhang1,† , Gengqi Yao1 , Chicheng Zhang1 , Miao Deng1 , Siyu Chen1 , Yiqi Dai1 , Shiqi Yue1 , Chijun Li1 , Yuqi Li1 , Ziwen Zhou1 , Zheli Liu1 , Xinyang Yu1 , Xitao Ji1 , Cheng Zeng1,*, Siqi Yan1,2,*, Jinsong Xia1,* and Ming Tang1,2,* 1 School of Optical and Electronic Information and Wuhan National Laboratory for Optoelectronics, Huazhong University of Science and Technology, Wuhan 430074, China 2 Hubei Optical Fundamental Research Centre, Wuhan 430074, China *Corresponding author: Cheng Zeng. Email: zengchengwuli@hust.

, Tang et al. p. 0
Where the paper says it

Email: jsxia@hust. cn and Ming Tang.

p. 0
Where the paper says it

Email: jsxia@hust. cn and Ming Tang.

, Li et al., Zhang et al., Ji et al., Walker, Pittala, Oswald, Rahim, Chang, Lin, Doerr, Holzgrafe, Yeh.

References (Specific Citations)

References 1-8 are cited in the introduction and methods sections to support claims about DCIs and SHC architectures References 9-37 are cited throughout the paper to support material limitations, tracking speed comparisons, and specific device characteristics.

References (Experimental Setup)

Figure 5 illustrates the experimental setup for ultrafast reset-free polarization tracking Figure 6 shows the system-level evaluation of the APC in SHC Link.

References (Device Characterization)

Figure 1 presents the device architecture and key building blocks of the TFLT-based APC Figure 2 shows the fabrication and electro-optic characterization of the TFLT-based APC. Figure 7 compares polarization tracking speed and half-wave voltage across representative integrated platforms. p. 8

Where the paper says it

Static and dynamic electro-optic characteristics were measured by launching a 1550 nm continuouswave laser into the chip and driving a single APC stage with a 1 MHz sawtooth waveform. Figure 2e illustrates the measured half-wave voltage of the Mach–Zehnder interferometer (MZI) of 2.

References (Algorithm Details)

Figure 4 presents the finite-boundary gradient-descent algorithm for reset-free polarization tracking Figure 8 shows the architecture of the polarization control electronics.

References (Performance Metrics)

Figure 5b summarizes the polarization tracking performance as a function of scrambling speed using the complementary cumulative distribution function (CCDF) of the relative intensity error (RIE) Figure 6b summarizes the measured BER performance as a function of scrambling speed.

References (Material Properties)

The text discusses intrinsic material advantages of TFLT, such as lower intrinsic defect density and weaker photorefractive effects compared to LN and the suppression of DC drift through interface engineering.

References (Control Loop Limits)

The maximum sustainable polarization rotation rate is governed by the loop latency, which sets the fastest rate at which corrective phase updates can be applied The TFLT phase shifters operate on picosecond timescales and support electro-optic bandwidths exceeding gigahertz.

References (Comparison to Other Platforms)

Figure 7 captures this advantage from a device-level perspective by comparing polarization tracking speed and half-wave voltage across representative integrated platforms The TFLT platform occupies a unique Pareto-optimal position, simultaneously achieving Mrad·s−1 tracking and sub-2.5-V operation. p. 1

Where the paper says it

be tracked at speeds up to 2 Mrad·s⁻¹, while stable reset-free operation under continuous polarization disturbances is maintained up to 1 Mrad·s⁻¹. This reset-free performance represents more than doubling the state of the art, while the pre-FEC bit-error rates remain below the HD-FEC threshold under realistic DCI conditions and lightning-scale polarization disturbances.

References (Future Applications)

The demonstrated platform is equally applicable to emerging DP-IMDD architectures, where stable and high-speed polarization control is essential for preserving channel orthogonality and maximizing spectral efficiency This work establishes TFLT as a key enabler for next-generation optical interconnects in AI-driven data centers and short-reach communication networks.

Conclusion (Final Statement)

We have demonstrated the first integrated polarization controller based on thin-film lithium tantalate, achieving reset-free phase-jump-free polarization tracking at unprecedented Mrad·s−1 speeds The observed performance boundary is shown to arise from finite control-loop latency rather than intrinsic photonic limitations. p. 2

Where the paper says it

Silicon photonic platforms offer excellent scalability and manufacturing maturity16 , but rely on thermo-optic or carrier-based phase shifters whose intrinsically slow response and parasitic intensity modulation fundamentally limit both the bandwidth and fidelity of polarization tracking17 . Thin-film lithium niobate enables fast electro-optic phase modulation, yet practical operation typically requires thermal bias control to compensate DC drift18,19 , introducing a slow control loop that conflicts with continuous and rapidly varying SOPs.

Methods (Detailed Control)

The execution flow of the algorithm, illustrated in Figure 4c, is implemented on the FPGA using a finite-state machine to ensure deterministic timing and real-time operation Each control cycle is partitioned into four sequential states for probing, compensation for loop latency, gradient estimation, and voltage update The total loop latency is approximately 100 ns.

Power System Details

The power-management system was implemented using a hierarchical DC–DC plus low-dropout regulator (LDO) architecture with electrically and physically isolated supply domains This architecture preserves high power-conversion efficiency while providing the low-noise supply rails required for stable high-speed closed-loop polarization control.

Final Summary

The proposed device exhibits low PDL, low half-wave voltage, and long-term bias stability When integrated into a 400-Gbps SHC transmission system, the APC maintains error-free operation under lightning-scale polarization scrambling The observed performance boundary is shown to arise from finite control-loop latency rather than intrinsic photonic limitations.

The reference list includes several works on polarization control and related technologies, such as those by Singh et al., Kumar et al., Sun et al., Wade et al., Cheng et al., Tang et al., Li et al., Zhang et al., Ji et al. and others. The paper also references foundational work on polarization control in coherent communications and experimental measurements of SOP transients due to lightning strikes. p. 3

Where the paper says it

Our device achieves polarization-tracking speeds up to 2 Mrad·s⁻¹ for transient polarization disturbances and stable reset-free operation under continuous polarization disturbances is maintained up to 1 Mrad·s⁻¹, representing the fastest integrated polarization tracking reported to date and covering virtually all polarization dynamics encountered in practical fiber links, from slow environmental drifts to extreme, lightning-scale perturbations, while preserving stable coherent reception throughout. By simultaneously delivering ultrafast response, low polarization-dependent loss (PDL), low driving voltage, and drift-free operation, this work establishes a new regime of polarization control, within which multiple key performance metrics extend beyond the current state of the art, unlocking the practical scalability of both SHC and DP-IMDD optical interconnects for next-generation AI-driven data-center networks.

Supplementary information is available online at https://doi.org/xxxxxx. The work is 2601.03652.

We have demonstrated the first integrated polarization controller based on thin-film lithium tantalate, achieving reset-free phase-jump-free polarization tracking at unprecedented Mrad·s−1 speeds. The observed performance boundary is shown to arise from finite control-loop latency rather than intrinsic photonic limitations.

The execution flow of the algorithm, illustrated in Figure 4c, is implemented on the FPGA using a finite-state machine to ensure deterministic timing and real-time operation Each control cycle is partitioned into four sequential states for probing, compensation for loop latency, gradient estimation, and voltage update.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Reset-free polarization tracking at Mrad·s−1 speeds for optical interconnects enables stable operation under continuous polarization disturbances up to 1 Mrad·s−1. This allows AI data center links to maintain high performance even during extreme transient events like lightning strikes without interruption.

  2. The system can sustain error-free operation in a 400-Gbps SHC transmission system when the polarization scrambling speed is up to 1 Mrad·s−1, as all measured bit error rates remain below the hard-decision FEC threshold. This provides robust, high-throughput data transfer for AI training workloads.

  3. The architecture is applicable to emerging DP-IMDD architectures, where stable and high-speed polarization control preserves channel orthogonality and maximizes spectral efficiency. This enables more efficient communication systems for short-reach data center links by suppressing inter-polarization crosstalk.

  4. The proposed platform achieves polarization tracking speeds up to 2 Mrad·s−1 for transient disturbances, covering virtually all polarization dynamics encountered in practical fiber links, from slow environmental drifts to lightning-scale perturbations. This allows the system to handle a wider range of realistic physical channel conditions than existing controllers.

  5. The control loop latency is approximately 100 ns, corresponding to a theoretical tracking bandwidth on the order of 10 MHz, which is limited by electronic and algorithmic delays rather than photonic device constraints. This informs the design of faster electronics needed for future scaling beyond Mrad·s−1 tracking limits.

Abstract

The rapid escalation of computing power driven by large-scale artificial intelligence is placing unprecedented demands on the bandwidth, latency, and energy efficiency of data-center interconnects (DCIs). Self-homodyne coherent (SHC) transmission is a promising architecture because it preserves the spectral efficiency of coherent detection while greatly simplifying digital signal processing, but its practical deployment is critically limited by random and often ultrafast state-of-polarization (SOP) fluctuations that induce carrier fading and destabilize coherent reception. Here we report the first integrated polarization controller based on thin-film lithium tantalate (TFLT), enabling reset-free polarization tracking at Mrad/s speeds. The four-stage electro-optic device exhibits polarization-dependent loss (PDL) below 0.3 dB, a half-wave voltage below 2.5 V, high modulation bandwidth, and negligible DC drift. To accommodate the finite tuning range of integrated phase shifters, we develop a finite-boundary gradient-descent (FBGD) control algorithm that ensures reset-free SOP evolution with no phase jump. The implemented adaptive polarization controller (APC) is validated through both standalone polarization-tracking measurements and a dual-polarization 16-QAM SHC 400-Gbps transmission system. Transient polarization disturbances can be tracked at speeds up to 2 Mrad/s, while stable reset-free operation under continuous polarization disturbances is maintained up to 1 Mrad/s. This reset-free performance represents more than doubling the state of the art, while the pre-FEC bit-error rates remain below the HD-FEC threshold under realistic DCI conditions and lightning-scale polarization disturbances. These results establish TFLT as a new platform for ultrafast, low-power, reset-free, and drift-free polarization control in coherent optical interconnects and beyond.

Related papers