Ligand Engineering for Precise Control of Ultrathin CsPbI3 Nanoplatelet Superlattices for Efficient Light-Emitting Diodes
Listen
Radio episode about this paper
Transcript
Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.
Kai: We're looking at the paper: "Ligand Engineering for Precise Control of Ultrathin CsPbI3 Nanoplatelet Superlattices for Efficient Light-Emitting Diodes".
Paper summary: Kai: So we're looking at this paper today on "Ligand Engineering for Precise Control of Ultrathin CsPbI3 Nanoplatelet Superlattices for Efficient Light-Emitting Diodes". What's the main idea here, Mira?
Mira: Well, the core thesis is that strongly confined perovskite nanoplatelets have potential that you don't find in regular nanocubes because they can produce linearly polarized light and get better light outcoupling by controlling a transition dipole moment. But realizing this requires these nanoplatelets to be ultrathin, with three or fewer monolayers of lead halide octahedra across the thickness, which is really hard to make uniformly and their brightness gets messed up by surface defects.
Lev: That's the hurdle, right? Because those limitations restrict how well we can use ultrathin PeNPLs in light-emitting diodes, especially when you're pushing them down to just a few monolayers across > Page three> <ref:2511.11107#pg1>.
Kai: Exactly. And that’s where this work comes in with an ancillary ligand engineering strategy. They show that using ligands with phosphoryl functional groups strongly binds to the perovskite surface, while the organic backbone keeps it from being too bulky, which helps create high ligand density. This modulation of nucleation and growth leads to these monodisperse nanoplatelets that stack much more uniformly when you assemble them into superlattices, and they don't clump up as much.
Mira: That sounds like they are tackling the uniformity problem directly by controlling how the material forms at the start, rather than just trying to fix defects later > Page two> <ref:2511.11107#pg1>. They’re aiming for better stacking and less agglomeration during self-assembly.
Lev: From a real hardware standpoint, suppressing that agglomeration is huge because if you have clumps in your superlattice structure, you get bad charge transport and performance loss on actual devices > Page one] <ref:2511.11107#pg1>.
Kai: And they found some specific molecular details matter. They calculated with density functional theory that ligands like DPPAc and BPAc have the highest surface adsorption energies on the (one)-terminated surface of the perovskite > Page two> <ref:2511.11107#pg1>. Plus, both of those ligands cause the biggest structural distortion and have shorter lead to oxygen bond lengths compared to oleic acid.
Mira: So it’s not just about sticking; it’s about how the ligand chemically interacts with the lead ions themselves, specifically how that phosphoryl group acts as a Lewis base coordinating with empty lead p states > Page two> <ref:2511.11107#pg1>. That coordination seems key to controlling the growth kinetics.
Paper summary: Lev: I wonder what that means kinetically. If these ligands retard formation, does it actually give you more time to regulate the crystal growth and control the final thickness?
Kai: In-situ photoluminescence measurements show that using BPAc and DPPAc PeNPLs causes a delayed photoluminescence onset and a slower spectral shift compared to the pristine nanoplatelets > Page two> <ref:2511.11107#pg1>. That suggests they are suppressing nucleation and regulating the crystal growth dynamics, which lines up with those strong bonds to the lead ions.
Mira: The result is very specific too. BPAc-PeNPLs show a single, sharp emission peak at six hundred nanometers wavelength with a full width at half maximum of about twenty-one nanometers, which matches what you expect from uniform three monolayer thick nanoplatelets > Page two> <ref:2511.11107#pg1>.
Lev: That sharpness is important for device physics. If the emission profile is that narrow, it means the material is very consistent in its optical properties across the whole film.
Kai: And then they take those optimized PeNPL superlattices and see real performance gains. They achieve an enhanced degree of polarization, reaching a maximum of eleven point eight percent with BPAc-PeNPL thin films, which is a big jump from three point six percent for the pristine ones > Page two> <ref:2511.11107#pg1>.
Mira: But they also look at the face-down orientation and see that it enhances outcoupling. They found that face-down oriented PeNPL superlattices result in light-emitting diodes with thirteen point one percent external quantum efficiency, which is the highest number reported for these ultrathin PeNPL LEDs > Page two> <ref:2511.11107#pg1>.
Lev: Thirteen point one percent external quantum efficiency is solid, but what’s the trade-off? You have to consider that face-down orientation is chosen specifically because of this superior outcoupling in the normal direction > Page one] <ref:2511.11107#pg1>.
Kai: Right. And they looked at the structural coherence as well. The BPAc PeNPL thin films showed a series of well-defined out-of-plane diffraction peaks corresponding to the one hundred zero, one zero one, and one zero two planes of the perovskite structure > Page two> <ref:2511.11107#pg1>. These patterns were much sharper and more intense than those in the pristine films.
Mira: That sharpness indicates superior long-range structural coherence, meaning the layers are stacked really well on top of each other, which is what you want for predictable device behavior > Page two> <ref:2511.11107#pg1>.
Paper summary: Lev: And the vertical spread of those diffraction features confirms coherent layer-by-layer stacking in those films > Page two> <ref:2511.11107#pg1>. That level of stacking consistency is what gets you out there with reliable performance.
Kai: When they looked at polarization response, the angle-resolved photoluminescence measurements on edge-up oriented superlattice films showed a significantly enhanced polarization response compared to pristine ones > Page two> <ref:2511.11107#pg1>.
Mira: They linked that improved angular emission profile to optical simulations which suggested that a higher fraction of horizontal transition dipole moments leads to more Lambertian-like emission > Page two> <ref:2511.11107#pg1>. That behavior is what drives the better outcoupling they are seeing.
Lev: So, the ligand isn't just making it brighter; it’s changing the fundamental way light leaves the material, which is a big deal for how we design these LEDs > Page one] <ref:2511.11107#pg1>.
Kai: The discussion on ligand functionality really hammers home that it’s a balance between how strongly the functional group coordinates and the steric profile of the backbone. It dictates nucleation, growth, and assembly all at once > Page two> <ref:2511.11107#pg1>.
Mira: So, achieving uniform monolayer PeNPLs with improved photoluminescence quantum yield can actually be done by using ancillary ligands that have both a strong Lewis base in the functional group and an organic backbone that isn't too bulky > Page two> <ref:2511.11107#pg1>.
Lev: It shows that ligand engineering is a viable path to making these anisotropic nanocrystals more useful for high-efficiency LEDs, provided you find the right chemical balance > Page one] <ref:2511.11107#pg1>.
Kai: So, to summarize this paper on "Ligand Engineering for Precise Control of Ultrathin CsPbI3 Nanoplatelet Superlattices for Efficient Light-Emitting Diodes", they show that by engineering ligands with phosphoryl groups and non-bulky backbones, you can precisely control the synthesis of ultrathin CsPbI3 nanoplatelets. This results in uniform superlattices that exhibit enhanced polarization and outcoupling properties, leading to a maximum external quantum efficiency of thirteen point one percent in face-down orientation > Page two> <ref:2511.11107#pg1>.
Mira: It’s about using chemistry at the surface to dictate the crystal growth process, moving from uncontrolled synthesis to a highly ordered structure.
Lev: For us on the engineering side, it means that if we can tune the ligand chemistry this precisely, we have a better recipe for building functional layered materials for actual devices > Page one] <ref:2511.11107#pg1>.
Conclusion: Kai: So we've seen how these new ligands help control those perovskite nanoplatelets and get better light outcoupling, now let's talk about what this paper is actually calling itself.
Mira: The title is "Ligand Engineering for Precise Control of Ultrathin CsPbI3 Nanoplatelet Superlattices for Efficient Light-Emitting Diodes". It’s pretty descriptive, right?
Lev: Yeah, it tells you exactly what they did: they engineered the ligands to control the synthesis and then used that to build superlattices that work in LEDs.
Kai: It's focused on achieving precise control over those ultrathin structures, getting them stacked uniformly. That sounds like a big deal for making reliable light sources.
Mira: Right. The implication is that this approach isn't just a tweak; it’s establishing a way to systematically build these anisotropic crystals for better performance in actual devices.
Lev: For real hardware, that means moving away from random growth toward something we can actually manufacture consistently on a large scale.
Kai: It suggests that the chemical environment right at the surface has massive control over the final optical output of these materials.
Mira: It really puts the focus on this synergy between molecular design and macroscopic device efficiency.
Lev: And it opens up possibilities for tailoring light emission properties specifically, like getting that polarization we talked about earlier.
Kai: So, it's not just about making a brighter LED; it's about making one with specific, predictable light characteristics.
Mira: Exactly. It moves the discussion from just "can we make this material" to "how do we make *this* material perform *this* way in a device?"
Lev: And that points us toward needing more rigorous control over the entire growth process, not just the initial nucleation step.
Jongbeom Kim, Woo Hyeon Jeong, Junzhi Ye, Allison Nicole Arber, Vikram Arber, Donghan Kim, Yi-Teng Huang, Yixin Wang, Dongeun Kim, Dongryeol Lee, Chia-Yu Chang, Xinyu Shen, Sung Yong Bae, Ashish Gaurav, Akshay Rao, Henry J. Snaith,
Department of Materials Science and Engineering, Ulsan National Institute of Science and Technology · School of Advanced Materials Science and Engineering, Sungkyunkwan University · Inorganic Chemistry Laboratory, University of Oxford · Institute of Polymer Optoelectronic Materials and Devices, Guangdong Basic Research Center of Excellence for Energy & Information Polymer Materials, State Key Laboratory of Luminescent Materials and Devices, School of Materials Science and Engineering, South China University of Technology · Department of Materials, University of Oxford · Graduate Institute of Photonics and Optoelectronics and Department of Electrical Engineering, National Taiwan University · Clarendon Laboratory, Department of Physics, University of Oxford · Cavendish Laboratory, University of Cambridge
physics.optics, cond-mat.mes-hall, cond-mat.mtrl-sci
Submitted: 2025-11-14
Updated: 2026-01-23
Comments: 25 pages, 4 figures, 1 table
DOI: 10.1002/adma.74023
License: http://creativecommons.org/licenses/by/4.0/
Importance score: 91/100
The gist: Strongly-confined perovskite nanoplatelets (PeNPLs) offer opportunities not found in conventional isotropic nanocubes, especially in producing linearly polarized light…
Key concepts
- Ancillary Ligand Engineering
- This involves using specific chemical molecules, like BPAc or DPPAc, to modify the surface of the perovskite material during synthesis. These ligands are chosen because they have a strong binding group (like a phosphoryl group) and an organic backbone that controls how the nanoparticles grow and stack together, ensuring uniformity.
- Structural Coherence in Superlattices
- This refers to how well the individual nanoplatelets stack on top of each other in a superlattice structure. The study showed that using the engineered ligands resulted in much sharper diffraction peaks, indicating superior long-range structural coherence and precise, layer-by-layer stacking.
- Outcoupling Efficiency
- This measures how effectively light escapes from the device structure into the surrounding medium. By controlling the shape and thickness of the face-down PeNPL superlattices using BPAc, researchers significantly increased outcoupling, leading to higher external quantum efficiency (EQE) in LEDs.
- Linear Polarization (DOP)
- This is a measure of how much the emitted light is polarized in a specific direction. The optimized BPAc-PeNPL superlattices showed enhanced linear polarization properties, which is crucial for applications like linearly polarized light sources and improves overall device efficiency.
Terminology
Summary
Strongly-confined perovskite nanoplatelets (PeNPLs) offer opportunities not found in conventional isotropic nanocubes, especially in producing linearly polarized light, as well as enhancing outcoupling through control over the transition dipole moment<ref:2511. p. 1 2
ABSTRACT
Strongly-confined perovskite nanoplatelets (PeNPLs) offer opportunities not found in conventional
isotropic nanocubes, especially in producing linearly polarized light, as well as enhancing outcoupling
through control over the transition dipole moment. But this requires ultrathin nanoplatelets with three
or fewer monolayers of PbI6 octahedra across the thickness, which are challenging to synthesise
uniformly, and their luminescence is strongly affected by surface defects. 1% external quantum efficiency, the highest reported for ultrathin PeNPLLEDs. This work establishes ancillary ligand-induced synthesis as a decisive route to achieve uniform
nanoplatelets with robust orientation control, enabling full utilization of the multifunctionality of
anisotropic PeNPLs.Where the paper says it
Where the paper says it
The Challenge and Proposed Solution
Strongly-confined perovskite nanoplatelets (PeNPLs) present challenges such as synthesizing them uniformly and ensuring their luminescence is not strongly affected by surface defects<ref:2511.11107#pg4> These limitations restrict the performance of ultrathin PeNPLs in light-emitting diodes (LEDs)<ref:2511. p. 1 But this requires ultrathin nanoplatelets with three
or fewer monolayers of PbI6 octahedra across the thickness, which are challenging to synthesise
uniformly, and their luminescence is strongly affected by surface defects. Together, these limit the
performance of ultrathin PeNPLs in light-emitting diodes (LEDs).Where the paper says it
Molecular Rationale for Ligand Design
The key determinants of an effective ancillary ligand are its backbone structure and Pb-coordination strength with the perovskite surface Density functional theory (DFT) calculations show that DPPAc and BPAc have the highest surface adsorption energies on the (001)-terminated surface of the perovskite Both DPPAc and BPAc were found to induce the highest degree of structural distortion, and both have the shortest Pb–O bond length compared to oleic acid The phosphoryl group in BPAc acts as a Lewis base coordinating with the empty Pb 6p states, sharing electron density between them
Kinetic Control and Morphological Uniformity
The introduction of ancillary ligands is hypothesized to retard PeNPL formation, thereby enabling regulation of crystallization and greater control over the final thickness In-situ photoluminescence (PL) measurements show that BPAc- and DPPAc-PeNPLs display a delayed PL onset and a slower spectral shift compared to pristine-PeNPLs This suggests suppressed nucleation and more regulated crystal growth dynamics, which is consistent with these ligands binding more strongly with Pb2+ Specifically, BPAc-PeNPLs exhibit a single, sharp emission peak at 600 nm wavelength (FWHM 21 nm), consistent with the formation of uniform 3ML-thick nanoplatelets
Enhanced Optical Performance in Devices
The optimized PeNPL superlattices achieve enhanced degree of polarization (DOP) and outcoupling Edge-up PeNPL superlattices show a maximum DOP of 11.8% with BPAc-PeNPL thin films, compared to 3. p. 9 2 | Optical characterization of pristine- and BPA-treated CsPbI3 PeNPL films
PL spectra of a Pristine-PeNPL thin films and b BPAc-PeNPL thin films showing contributions from
3ML and 4ML components. c PLQY distributions and d confocal PL images of each PeNPL thin film
(scan area: 120 × 120 μm2
). By modulating nucleation and growth, these ancillary ligands lead
to monodisperse PeNPLs that stack more uniformly when self-assembled into superlattices, with
suppressed agglomeration. As a result, from edge-up PeNPL superlattices, we achieve enhanced degree
of polarization, while from face-down PeNPL superlattices, we achieve enhanced outcoupling that
results in LEDs with 13.Where the paper says it
Where the paper says it
Conclusion and Broader Applicability
The findings establish that ancillary ligand-induced synthesis of uniform-ML PeNPLs is a robust route to fully exploit the multifunctionality of these anisotropic nanocrystals The synergistic effects of BPAc as an ancillary ligand not only enhance device efficiency but also improve their linear polarization properties These design principles can be more broadly applied across the wider PeNPL family, as well as other NPL materials systems The improved uniformity and PLQY allow for the formation of highly-ordered, and highly-emissive PeNPL superlattices
References
Liu M et al. Colloidal quantum dot electronics. p. 8 Second, even
when crystal growth is effectively controlled, the steric bulk of the ancillary ligands can modulate the
surface chemistry and, in turn, alter the uniformity in thickness of the resulting PeNPLs. Based on the understanding of the nucleation and growth kinetics of ancillary ligand incorporation, to
investigate the impact of the BPAc ligands on the optical properties of PeNPLs, we performed
photoluminescence quantum yield (PLQY) and time-resolved photoluminescence (TRPL)
measurements for both pristine-PeNPL and BPAc-PeNPL colloidal solutions. Second, even
when crystal growth is effectively controlled, the steric bulk of the ancillary ligands can modulate the
surface chemistry and, in turn, alter the uniformity in thickness of the resulting PeNPLs. Based on the understanding of the nucleation and growth kinetics of ancillary ligand incorporation, to
investigate the impact of the BPAc ligands on the optical properties of PeNPLs, we performed
photoluminescence quantum yield (PLQY) and time-resolved photoluminescence (TRPL)
measurements for both pristine-PeNPL and BPAc-PeNPL colloidal solutions. Saiful Islam5
*, Bo Ram Lee2
*, Myoung Hoon Song1
* Robert L. Hoye3
*
1
Department of Materials Science and Engineering, Ulsan National Institute of Science and
Technology (UNIST), Ulsan, 44919 Republic of Korea
2
School of Advanced Materials Science and Engineering, Sungkyunkwan University, Suwon,
16419, Republic of Korea
3
Inorganic Chemistry Laboratory, University of Oxford, Oxford, OX1 3QR, United Kingdom
4
Institute of Polymer Optoelectronic Materials and Devices, Guangdong Basic Research Center
of Excellence for Energy & Information Polymer Materials, State Key Laboratory of
Luminescent Materials and Devices, School of Materials Science and Engineering, South
China University of Technology, Guangzhou 510640, China. Saiful Islam5
*, Bo Ram Lee2
*, Myoung Hoon Song1
* Robert L. Hoye3
*
1
Department of Materials Science and Engineering, Ulsan National Institute of Science and
Technology (UNIST), Ulsan, 44919 Republic of Korea
2
School of Advanced Materials Science and Engineering, Sungkyunkwan University, Suwon,
16419, Republic of Korea
3
Inorganic Chemistry Laboratory, University of Oxford, Oxford, OX1 3QR, United Kingdom
4
Institute of Polymer Optoelectronic Materials and Devices, Guangdong Basic Research Center
of Excellence for Energy & Information Polymer Materials, State Key Laboratory of
Luminescent Materials and Devices, School of Materials Science and Engineering, South
China University of Technology, Guangzhou 510640, China. This work establishes ancillary ligand-induced synthesis as a decisive route to achieve uniform
nanoplatelets with robust orientation control, enabling full utilization of the multifunctionality of
anisotropic PeNPLs. Keywords: perovskite nanoplatelets, linearly polarized light emission, superlattices, nanocrystal
growth control, light-emitting diode This work establishes ancillary ligand-induced synthesis as a decisive route to achieve uniform
nanoplatelets with robust orientation control, enabling full utilization of the multifunctionality of
anisotropic PeNPLs. Keywords: perovskite nanoplatelets, linearly polarized light emission, superlattices, nanocrystal
growth control, light-emitting diode 3
INTRODUCTION
Colloidal semiconductor nanocrystals (NCs) offer advantages for optics and photonics, as well as for
fundamental investigations of light-matter properties1, 2, 3. To fully realize these benefits, it is critical to
achieve highly monodisperse NCs, which requires precise control over nucleation and growth via wellregulated reaction conditions4, 5, 6, 7, 8. 3
INTRODUCTION
Colloidal semiconductor nanocrystals (NCs) offer advantages for optics and photonics, as well as for
fundamental investigations of light-matter properties1, 2, 3. To fully realize these benefits, it is critical to
achieve highly monodisperse NCs, which requires precise control over nucleation and growth via wellregulated reaction conditions4, 5, 6, 7, 8. To fully realize these benefits, it is critical to
achieve highly monodisperse NCs, which requires precise control over nucleation and growth via wellregulated reaction conditions4, 5, 6, 7, 8. Lead halide perovskites, with the general formula APbX3 (A =
formamidinium, methylammonium, Cs; X = Cl, Br, I), have emerged as one of the most promising NC
materials, due to their narrow full-width at half-maximum (FWHM), defect tolerance, and the ability to
achieve high luminescence quantum yields with cost-effective solution processing methods9, 10, 11, 12, 13. To fully realize these benefits, it is critical to
achieve highly monodisperse NCs, which requires precise control over nucleation and growth via wellregulated reaction conditions4, 5, 6, 7, 8. Lead halide perovskites, with the general formula APbX3 (A =
formamidinium, methylammonium, Cs; X = Cl, Br, I), have emerged as one of the most promising NC
materials, due to their narrow full-width at half-maximum (FWHM), defect tolerance, and the ability to
achieve high luminescence quantum yields with cost-effective solution processing methods9, 10, 11, 12, 13. 3
INTRODUCTION
Colloidal semiconductor nanocrystals (NCs) offer advantages for optics and photonics, as well as for
fundamental investigations of light-matter properties1, 2, 3. To fully realize these benefits, it is critical to
achieve highly monodisperse NCs, which requires precise control over nucleation and growth via wellregulated reaction conditions4, 5, 6, 7, 8. 3
INTRODUCTION
Colloidal semiconductor nanocrystals (NCs) offer advantages for optics and photonics, as well as for
fundamental investigations of light-matter properties1, 2, 3. To fully realize these benefits, it is critical to
achieve highly monodisperse NCs, which requires precise control over nucleation and growth via wellregulated reaction conditions4, 5, 6, 7, 8. 3
INTRODUCTION
Colloidal semiconductor nanocrystals (NCs) offer advantages for optics and photonics, as well as for
fundamental investigations of light-matter properties1, 2, 3. To fully realize these benefits, it is critical to
achieve highly monodisperse NCs, which requires precise control over nucleation and growth via wellregulated reaction conditions4, 5, 6, 7, 8. 3
INTRODUCTION
Colloidal semiconductor nanocrystals (NCs) offer advantages for optics and photonics, as well as for
fundamental investigations of light-matter properties1, 2, 3. To fully realize these benefits, it is critical to
achieve highly monodisperse NCs, which requires precise control over nucleation and growth via wellregulated reaction conditions4, 5, 6, 7, 8. Prior studies have shown that the pronounced linearly polarized emission from PeNPLs is strongly
thickness-dependent and most reliably obtained in the ultrathin regime (typically n ≤ 3, where n is the
number of monolayers of Pb-halide octahedra across the thickness of the PeNPL). In ultrathin PeNPLs,
anisotropic confinement maximizes the fine structure splitting in the bright excitonic manifold, where
the excitonic state associated with the out-of-plane direction is raised in energy more than the doubly
degenerate in-plane excitonic states 18, 19, 20. Prior studies have shown that the pronounced linearly polarized emission from PeNPLs is strongly
thickness-dependent and most reliably obtained in the ultrathin regime (typically n ≤ 3, where n is the
number of monolayers of Pb-halide octahedra across the thickness of the PeNPL). In ultrathin PeNPLs,
anisotropic confinement maximizes the fine structure splitting in the bright excitonic manifold, where
the excitonic state associated with the out-of-plane direction is raised in energy more than the doubly
degenerate in-plane excitonic states 18, 19, 20. While these native ligands play a crucial role in
PeNPL synthesis, their weak surface binding affinity leads to dynamic ligand desorption, resulting in
poor colloidal stability and surface defect formation, including halide vacancies and uncoordinated Pb
ions30, 31, 32. These defects can lead to aggregation between PeNPLs or decomposition, resulting in a
distribution in PeNPL thicknesses, which prevents the realization of colour-pure LEDs with a high
degree of linear polarisation. While these native ligands play a crucial role in
PeNPL synthesis, their weak surface binding affinity leads to dynamic ligand desorption, resulting in
poor colloidal stability and surface defect formation, including halide vacancies and uncoordinated Pb
ions30, 31, 32. These defects can lead to aggregation between PeNPLs or decomposition, resulting in a
distribution in PeNPL thicknesses, which prevents the realization of colour-pure LEDs with a high
degree of linear polarisation. To fully realize these benefits, it is critical to
achieve highly monodisperse NCs, which requires precise control over nucleation and growth via wellregulated reaction conditions4, 5, 6, 7, 8. Lead halide perovskites, with the general formula APbX3 (A =
formamidinium, methylammonium, Cs; X = Cl, Br, I), have emerged as one of the most promising NC
materials, due to their narrow full-width at half-maximum (FWHM), defect tolerance, and the ability to
achieve high luminescence quantum yields with cost-effective solution processing methods9, 10, 11, 12, 13. To fully realize these benefits, it is critical to
achieve highly monodisperse NCs, which requires precise control over nucleation and growth via wellregulated reaction conditions4, 5, 6, 7, 8. Lead halide perovskites, with the general formula APbX3 (A =
formamidinium, methylammonium, Cs; X = Cl, Br, I), have emerged as one of the most promising NC
materials, due to their narrow full-width at half-maximum (FWHM), defect tolerance, and the ability to
achieve high luminescence quantum yields with cost-effective solution processing methods9, 10, 11, 12, 13. Understanding the interactions between Pb precursors and coordinating ligands at the atomic scale is
critical for elucidating how crystallization can be regulated. Prior to experimental investigation, density
functional theory (DFT) calculations were performed to provide atomistic insights into ligand-surface
interactions to clarify the role of specific ligands (Computational details in Methods). Understanding the interactions between Pb precursors and coordinating ligands at the atomic scale is
critical for elucidating how crystallization can be regulated. Prior to experimental investigation, density
functional theory (DFT) calculations were performed to provide atomistic insights into ligand-surface
interactions to clarify the role of specific ligands (Computational details in Methods). This work establishes ancillary ligand-induced synthesis as a decisive route to achieve uniform
nanoplatelets with robust orientation control, enabling full utilization of the multifunctionality of
anisotropic PeNPLs. Keywords: perovskite nanoplatelets, linearly polarized light emission, superlattices, nanocrystal
growth control, light-emitting diode This work establishes ancillary ligand-induced synthesis as a decisive route to achieve uniform
nanoplatelets with robust orientation control, enabling full utilization of the multifunctionality of
anisotropic PeNPLs. Keywords: perovskite nanoplatelets, linearly polarized light emission, superlattices, nanocrystal
growth control, light-emitting diode Prior studies have shown that the pronounced linearly polarized emission from PeNPLs is strongly
thickness-dependent and most reliably obtained in the ultrathin regime (typically n ≤ 3, where n is the
number of monolayers of Pb-halide octahedra across the thickness of the PeNPL). In ultrathin PeNPLs,
anisotropic confinement maximizes the fine structure splitting in the bright excitonic manifold, where
the excitonic state associated with the out-of-plane direction is raised in energy more than the doubly
degenerate in-plane excitonic states 18, 19, 20. Prior studies have shown that the pronounced linearly polarized emission from PeNPLs is strongly
thickness-dependent and most reliably obtained in the ultrathin regime (typically n ≤ 3, where n is the
number of monolayers of Pb-halide octahedra across the thickness of the PeNPL). In ultrathin PeNPLs,
anisotropic confinement maximizes the fine structure splitting in the bright excitonic manifold, where
the excitonic state associated with the out-of-plane direction is raised in energy more than the doubly
degenerate in-plane excitonic states 18, 19, 20. This work establishes ancillary ligand-induced synthesis as a decisive route to achieve uniform
nanoplatelets with robust orientation control, enabling full utilization of the multifunctionality of
anisotropic PeNPLs. Keywords: perovskite nanoplatelets, linearly polarized light emission, superlattices, nanocrystal
growth control, light-emitting diode This work establishes ancillary ligand-induced synthesis as a decisive route to achieve uniform
nanoplatelets with robust orientation control, enabling full utilization of the multifunctionality of
anisotropic PeNPLs. Keywords: perovskite nanoplatelets, linearly polarized light emission, superlattices, nanocrystal
growth control, light-emitting diode To fully realize these benefits, it is critical to
achieve highly monodisperse NCs, which requires precise control over nucleation and growth via wellregulated reaction conditions4, 5, 6, 7, 8. Lead halide perovskites, with the general formula APbX3 (A =
formamidinium, methylammonium, Cs; X = Cl, Br, I), have emerged as one of the most promising NC
materials, due to their narrow full-width at half-maximum (FWHM), defect tolerance, and the ability to
achieve high luminescence quantum yields with cost-effective solution processing methods9, 10, 11, 12, 13. To fully realize these benefits, it is critical to
achieve highly monodisperse NCs, which requires precise control over nucleation and growth via wellregulated reaction conditions4, 5, 6, 7, 8. Lead halide perovskites, with the general formula APbX3 (A =
formamidinium, methylammonium, Cs; X = Cl, Br, I), have emerged as one of the most promising NC
materials, due to their narrow full-width at half-maximum (FWHM), defect tolerance, and the ability to
achieve high luminescence quantum yields with cost-effective solution processing methods9, 10, 11, 12, 13. This work establishes ancillary ligand-induced synthesis as a decisive route to achieve uniform
nanoplatelets with robust orientation control, enabling full utilization of the multifunctionality of
anisotropic PeNPLs. Keywords: perovskite nanoplatelets, linearly polarized light emission, superlattices, nanocrystal
growth control, light-emitting diode This work establishes ancillary ligand-induced synthesis as a decisive route to achieve uniform
nanoplatelets with robust orientation control, enabling full utilization of the multifunctionality of
anisotropic PeNPLs. Keywords: perovskite nanoplatelets, linearly polarized light emission, superlattices, nanocrystal
growth control, light-emitting diode This work establishes ancillary ligand-induced synthesis as a decisive route to achieve uniform
nanoplatelets with robust orientation control, enabling full utilization of the multifunctionality of
anisotropic PeNPLs. Keywords: perovskite nanoplatelets, linearly polarized light emission, superlattices, nanocrystal
growth control, light-emitting diode This work establishes ancillary ligand-induced synthesis as a decisive route to achieve uniform
nanoplatelets with robust orientation control, enabling full utilization of the multifunctionality of
anisotropic PeNPLs. Keywords: perovskite nanoplatelets, linearly polarized light emission, superlattices, nanocrystal
growth control, light-emitting diode Therefore, to achieve efficient red-emitting iodide-based
PeNPLs, it is essential to develop monodisperse PeNPLs while implementing advanced passivation
strategies to overcome the limitations posed by native ligands. Motivated by these challenges, we systematically investigate an ancillary ligand-induced synthesis
approach to precisely control the nucleation and growth of CsPbI3 PeNPLs. Therefore, to achieve efficient red-emitting iodide-based
PeNPLs, it is essential to develop monodisperse PeNPLs while implementing advanced passivation
strategies to overcome the limitations posed by native ligands. Motivated by these challenges, we systematically investigate an ancillary ligand-induced synthesis
approach to precisely control the nucleation and growth of CsPbI3 PeNPLs. Therefore, to achieve efficient red-emitting iodide-based
PeNPLs, it is essential to develop monodisperse PeNPLs while implementing advanced passivation
strategies to overcome the limitations posed by native ligands. Motivated by these challenges, we systematically investigate an ancillary ligand-induced synthesis
approach to precisely control the nucleation and growth of CsPbI3 PeNPLs. Therefore, to achieve efficient red-emitting iodide-based
PeNPLs, it is essential to develop monodisperse PeNPLs while implementing advanced passivation
strategies to overcome the limitations posed by native ligands. Motivated by these challenges, we systematically investigate an ancillary ligand-induced synthesis
approach to precisely control the nucleation and growth of CsPbI3 PeNPLs. But this requires ultrathin nanoplatelets with three
or fewer monolayers of PbI6 octahedra across the thickness, which are challenging to synthesise
uniformly, and their luminescence is strongly affected by surface defects. Together, these limit the
performance of ultrathin PeNPLs in light-emitting diodes (LEDs). But this requires ultrathin nanoplatelets with three
or fewer monolayers of PbI6 octahedra across the thickness, which are challenging to synthesise
uniformly, and their luminescence is strongly affected by surface defects. Together, these limit the
performance of ultrathin PeNPLs in light-emitting diodes (LEDs). This work establishes ancillary ligand-induced synthesis as a decisive route to achieve uniform
nanoplatelets with robust orientation control, enabling full utilization of the multifunctionality of
anisotropic PeNPLs. Keywords: perovskite nanoplatelets, linearly polarized light emission, superlattices, nanocrystal
growth control, light-emitting diode This work establishes ancillary ligand-induced synthesis as a decisive route to achieve uniform
nanoplatelets with robust orientation control, enabling full utilization of the multifunctionality of
anisotropic PeNPLs. Keywords: perovskite nanoplatelets, linearly polarized light emission, superlattices, nanocrystal
growth control, light-emitting diode Thicker nanoplatelets generally exhibit a weaker
polarization response due to reduced exciton fine structure splitting. Beyond the intrinsic excitonic
effects, the pronounced shape anisotropy of ultrathin PeNPLs can also promote orientational ordering
and superlattice assembly, allowing control of the transition dipole moment in films21. Thicker nanoplatelets generally exhibit a weaker
polarization response due to reduced exciton fine structure splitting. Beyond the intrinsic excitonic
effects, the pronounced shape anisotropy of ultrathin PeNPLs can also promote orientational ordering
and superlattice assembly, allowing control of the transition dipole moment in films21. Second, even
when crystal growth is effectively controlled, the steric bulk of the ancillary ligands can modulate the
surface chemistry and, in turn, alter the uniformity in thickness of the resulting PeNPLs. Based on the understanding of the nucleation and growth kinetics of ancillary ligand incorporation, to
investigate the impact of the BPAc ligands on the optical properties of PeNPLs, we performed
photoluminescence quantum yield (PLQY) and time-resolved photoluminescence (TRPL)
measurements for both pristine-PeNPL and BPAc-PeNPL colloidal solutions. Second, even
when crystal growth is effectively controlled, the steric bulk of the ancillary ligands can modulate the
surface chemistry and, in turn, alter the uniformity in thickness of the resulting PeNPLs. Based on the understanding of the nucleation and growth kinetics of ancillary ligand incorporation, to
investigate the impact of the BPAc ligands on the optical properties of PeNPLs, we performed
photoluminescence quantum yield (PLQY) and time-resolved photoluminescence (TRPL)
measurements for both pristine-PeNPL and BPAc-PeNPL colloidal solutions. But this requires ultrathin nanoplatelets with three
or fewer monolayers of PbI6 octahedra across the thickness, which are challenging to synthesise
uniformly, and their luminescence is strongly affected by surface defects. Together, these limit the
performance of ultrathin PeNPLs in light-emitting diodes (LEDs). But this requires ultrathin nanoplatelets with three
or fewer monolayers of PbI6 octahedra across the thickness, which are challenging to synthesise
uniformly, and their luminescence is strongly affected by surface defects. Together, these limit the
performance of ultrathin PeNPLs in light-emitting diodes (LEDs). 1
Ligand Engineering for Precise Control of Ultrathin CsPbI3
Nanoplatelet Superlattices for Efficient Light-Emitting Diodes
Jongbeom Kim1,†, Woo Hyeon Jeong2,3,†, Junzhi Ye3,4*, Allison Nicole Arber5
, Vikram5
,
Donghan Kim1
, Yi-Teng Huang3,6
, Yixin Wang3
, Dongeun Kim1
, Dongryeol Lee1
, Chia-Yu
Chang3
, Xinyu Shen7
, Sung Yong Bae3
, Ashish Gaurav3
, Akshay Rao8
, Henry J. Snaith7
, M. 1
Ligand Engineering for Precise Control of Ultrathin CsPbI3
Nanoplatelet Superlattices for Efficient Light-Emitting Diodes
Jongbeom Kim1,†, Woo Hyeon Jeong2,3,†, Junzhi Ye3,4*, Allison Nicole Arber5
, Vikram5
,
Donghan Kim1
, Yi-Teng Huang3,6
, Yixin Wang3
, Dongeun Kim1
, Dongryeol Lee1
, Chia-Yu
Chang3
, Xinyu Shen7
, Sung Yong Bae3
, Ashish Gaurav3
, Akshay Rao8
, Henry J. Snaith7
, M. Lead halide perovskites, with the general formula APbX3 (A =
formamidinium, methylammonium, Cs; X = Cl, Br, I), have emerged as one of the most promising NC
materials, due to their narrow full-width at half-maximum (FWHM), defect tolerance, and the ability to
achieve high luminescence quantum yields with cost-effective solution processing methods9, 10, 11, 12, 13. In particular, perovskite nanoplatelets (PeNPLs), classified by the number of monolayers (MLs) of leadhalide octahedra across the thickness, can have their emission wavelength tuned not only by changing
their composition, but also by tuning their thickness. Lead halide perovskites, with the general formula APbX3 (A =
formamidinium, methylammonium, Cs; X = Cl, Br, I), have emerged as one of the most promising NC
materials, due to their narrow full-width at half-maximum (FWHM), defect tolerance, and the ability to
achieve high luminescence quantum yields with cost-effective solution processing methods9, 10, 11, 12, 13. In particular, perovskite nanoplatelets (PeNPLs), classified by the number of monolayers (MLs) of leadhalide octahedra across the thickness, can have their emission wavelength tuned not only by changing
their composition, but also by tuning their thickness. Understanding the interactions between Pb precursors and coordinating ligands at the atomic scale is
critical for elucidating how crystallization can be regulated. Prior to experimental investigation, density
functional theory (DFT) calculations were performed to provide atomistic insights into ligand-surface
interactions to clarify the role of specific ligands (Computational details in Methods). Understanding the interactions between Pb precursors and coordinating ligands at the atomic scale is
critical for elucidating how crystallization can be regulated. Prior to experimental investigation, density
functional theory (DFT) calculations were performed to provide atomistic insights into ligand-surface
interactions to clarify the role of specific ligands (Computational details in Methods). This is consistent with O from the
phosphoryl functional group in BPAc acting as a Lewis base and coordinating with the empty Pb 6p
states, with electron density shared between them. Bader charge analysis (Fig. This is consistent with O from the
phosphoryl functional group in BPAc acting as a Lewis base and coordinating with the empty Pb 6p
states, with electron density shared between them. Bader charge analysis (Fig. The high surface area-to-volume ratio amplifies sensitivity to ligand dynamics and
surface defects, thereby requiring robust surface passivation. PeNPLs present inherent challenges due to their fast reaction kinetics, which stems from their ionic
nature and low formation energy, making it difficult to achieve nanoplatelets that are uniform in
thickness5, 22, 23. The high surface area-to-volume ratio amplifies sensitivity to ligand dynamics and
surface defects, thereby requiring robust surface passivation. PeNPLs present inherent challenges due to their fast reaction kinetics, which stems from their ionic
nature and low formation energy, making it difficult to achieve nanoplatelets that are uniform in
thickness5, 22, 23. These defects can lead to aggregation between PeNPLs or decomposition, resulting in a
distribution in PeNPL thicknesses, which prevents the realization of colour-pure LEDs with a high
degree of linear polarisation. This instability is further exacerbated during thin film formation, due to
ligand desorption, diminishing both the stability and optical properties of PeNPLs33, 34. As a result, from edge-up PeNPL superlattices, we achieve enhanced degree
of polarization, while from face-down PeNPL superlattices, we achieve enhanced outcoupling that
results in LEDs with 13. 1% external quantum efficiency, the highest reported for ultrathin PeNPLLEDs.Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Device Performance Comparison
The champion BPAc-PeNPL device achieved a maximum EQE of 13.1%, significantly surpassing the 2. p. 3 Ancillary ligands that optimally satisfy these two determining factors
modulate the crystal growth kinetics, enabling the formation of uniform 3ML-thick PeNPLs while
simultaneously passivating surface defects. These PeNPLs not only retain homogeneous emission upon
thin-film formation but also self-assemble into well-ordered superlattices with significantly enhanced
optical properties compared to pristine PeNPLs, owing to their well-passivated surfaces that suppress
agglomeration.Where the paper says it
Device Architecture and Orientation
To maximize outcoupling, the facedown orientation was selected for the primary device architecture due to its superior outcoupling in the normal direction The device performance results of edge-up oriented LEDs exhibit lower efficiencies than the face-down PeNPL devices due to reduced outcoupling in the normal direction The champion BPAc-PeNPL device achieved a maximum EQE of 13.1% at 2.4V, compared to 2. p. 3 Ancillary ligands that optimally satisfy these two determining factors
modulate the crystal growth kinetics, enabling the formation of uniform 3ML-thick PeNPLs while
simultaneously passivating surface defects. These PeNPLs not only retain homogeneous emission upon
thin-film formation but also self-assemble into well-ordered superlattices with significantly enhanced
optical properties compared to pristine PeNPLs, owing to their well-passivated surfaces that suppress
agglomeration.Where the paper says it
Structural Coherence in Superlattices
BPAcPeNPL thin films exhibited a series of well-defined out-of-plane diffraction peaks corresponding to the (100), (101), and (102) planes of the perovskite structure These patterns were significantly sharper and more intense than those of the pristine-PeNPL thin films, indicating superior long-range structural coherence and crystallinity The vertical spread of the diffraction features further confirms coherent layer-by-layer stacking in the BPAc-PeNPL films Face-down orientations exhibited stronger intensity in the low azimuthal angle range (0°–10°), while edge-up orientations showed enhanced scattering at higher angles (80°–90°) due to improved monodispersity The results highlight the critical role of the BPAc ancillary ligand in enabling the formation of highly-ordered, structurally-coherent PeNPL superlattices
Linearly Polarized Light Emission and Outcoupling
The angle-resolved PL measurements of edge-up oriented PeNPL superlattice films show a significantly enhanced polarization response for BPAc-PeNPL thin films compared to pristine-PeNPL thin films The improved angular emission profile with BPAc treatment is consistent with optical simulations indicating that a higher fraction of horizontal transition dipole moments leads to more Lambertian-like emission This behavior suggests that BPAc-PeNPLs would exhibit higher outcoupling, which is particularly advantageous for LED applications The synergistic effects contribute to the superior device performance of BPAc-PeNPL LED devices compared to the pristine-PeNPL LEDs
Discussion on Ligand Functionality
The molecular structure of the ancillary ligand governs nucleation, growth, and assembly through a synergistic balance between headgroup coordination and backbone steric effects The coordination strength of the functional group to Pb2+ influences the barrier to nanoplatelet nucleation, while the steric profile dictates anisotropic growth and colloidal stability When these factors are optimally balanced, growth converges toward uniform monolayer PeNPLs with well-passivated surfaces The results show that achieving PeNPLs with improved uniformity and PLQY can be realized using ancillary ligands containing a strong Lewis base in the functional group, as well as an organic backbone that is not overly bulky This demonstrates the feasibility of ligand engineering as a promising approach to advance the development of high-efficiency, strongly confined PeNPL-based LEDs
Data Availability and Acknowledgements
Raw data for the main text and supplementary information available from the Oxford Research Archive repository [DOI to be made available before publication] J. Y. and R. L. Z. H. thank the UK Research and Innovation for funding through a Frontier Grant (no. p. 0 Saiful Islam5
*, Bo Ram Lee2
*, Myoung Hoon Song1
* Robert L. Hoye3
*
1
Department of Materials Science and Engineering, Ulsan National Institute of Science and
Technology (UNIST), Ulsan, 44919 Republic of Korea
2
School of Advanced Materials Science and Engineering, Sungkyunkwan University, Suwon,
16419, Republic of Korea
3
Inorganic Chemistry Laboratory, University of Oxford, Oxford, OX1 3QR, United Kingdom
4
Institute of Polymer Optoelectronic Materials and Devices, Guangdong Basic Research Center
of Excellence for Energy & Information Polymer Materials, State Key Laboratory of
Luminescent Materials and Devices, School of Materials Science and Engineering, South
China University of Technology, Guangzhou 510640, China. Hoye3
*
1
Department of Materials Science and Engineering, Ulsan National Institute of Science and
Technology (UNIST), Ulsan, 44919 Republic of Korea
2
School of Advanced Materials Science and Engineering, Sungkyunkwan University, Suwon,
16419, Republic of Korea
3
Inorganic Chemistry Laboratory, University of Oxford, Oxford, OX1 3QR, United Kingdom
4
Institute of Polymer Optoelectronic Materials and Devices, Guangdong Basic Research Center
of Excellence for Energy & Information Polymer Materials, State Key Laboratory of
Luminescent Materials and Devices, School of Materials Science and Engineering, South
China University of Technology, Guangzhou 510640, China. 5
Department of Materials, University of Oxford, Oxford, OX1 3PH, United Kingdom
6
Graduate Institute of Photonics and Optoelectronics and Department of Electrical Engineering,
National Taiwan University, Taipei 10617, Taiwan
7
Clarendon Laboratory, Department of Physics, University of Oxford, Oxford, OX1 3PU
United Kingdom
8
Cavendish Laboratory, University of Cambridge, Cambridge CB3 0US, United Kingdom
†
These authors contributed equally. The increased PLQY of BPAc-PeNPLs suggests effective passivation
of surface defects, reducing nonradiative recombination. Time-resolved PL decay measurements further
support the strongly passivating nature of BPAc ligands. Saiful Islam5
*, Bo Ram Lee2
*, Myoung Hoon Song1
* Robert L. Hoye3
*
1
Department of Materials Science and Engineering, Ulsan National Institute of Science and
Technology (UNIST), Ulsan, 44919 Republic of Korea
2
School of Advanced Materials Science and Engineering, Sungkyunkwan University, Suwon,
16419, Republic of Korea
3
Inorganic Chemistry Laboratory, University of Oxford, Oxford, OX1 3QR, United Kingdom
4
Institute of Polymer Optoelectronic Materials and Devices, Guangdong Basic Research Center
of Excellence for Energy & Information Polymer Materials, State Key Laboratory of
Luminescent Materials and Devices, School of Materials Science and Engineering, South
China University of Technology, Guangzhou 510640, China. Hoye3
*
1
Department of Materials Science and Engineering, Ulsan National Institute of Science and
Technology (UNIST), Ulsan, 44919 Republic of Korea
2
School of Advanced Materials Science and Engineering, Sungkyunkwan University, Suwon,
16419, Republic of Korea
3
Inorganic Chemistry Laboratory, University of Oxford, Oxford, OX1 3QR, United Kingdom
4
Institute of Polymer Optoelectronic Materials and Devices, Guangdong Basic Research Center
of Excellence for Energy & Information Polymer Materials, State Key Laboratory of
Luminescent Materials and Devices, School of Materials Science and Engineering, South
China University of Technology, Guangzhou 510640, China. 5
Department of Materials, University of Oxford, Oxford, OX1 3PH, United Kingdom
6
Graduate Institute of Photonics and Optoelectronics and Department of Electrical Engineering,
National Taiwan University, Taipei 10617, Taiwan
7
Clarendon Laboratory, Department of Physics, University of Oxford, Oxford, OX1 3PU
United Kingdom
8
Cavendish Laboratory, University of Cambridge, Cambridge CB3 0US, United Kingdom
†
These authors contributed equally.Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Liu M et al. Colloidal quantum dot electronics. Boles MA et al. The surface science of nanocrystals. Chen Q et al. All-inorganic perovskite nanocrystal scintillators. Kim T et al. Diffusion dynamics controlled colloidal synthesis of highly monodisperse InAs nanocrystals. Akkerman QA et al. Controlling the nucleation and growth kinetics of lead halide perovskite quantum dots. Peng X et al. Kinetics of II-VI and III-V Colloidal Semiconductor Nanocrystal Growth: “Focusing” of Size Distributions. Murray CB et al. Synthesis and characterization of nearly monodisperse CdE (E = sulfur, selenium, tellurium) semiconductor nanocrystallites. Dey A et al. State of the Art and Prospects for Halide Perovskite Nanocrystals. Huang H et al. Colloidal lead halide perovskite nanocrystals: synthesis, optical properties and applications. Mosquera-Lois I et al. Multifaceted nature of defect tolerance in halide perovskites and emerging semiconductors. Han S et al. Synergistic Hybrid-Ligand Passivation of Perovskite Quantum Dots: Suppressing Reduced-Dimensionality and Enhancing Optoelectronic Performance. Hammer MS et al. Bridging theory and experiment in defect-tolerant semiconductors for photovoltaics. Ye J et al. Direct linearly polarized electroluminescence from perovskite nanoplatelet superlattices. Wang S et al. Thickness-Dependent Dark-Bright Exciton Splitting and Phonon Bottleneck in CsPbBr3-Based Nanoplatelets Revealed via Magneto-Optical Spectroscopy. Otero-Martinez C et al. Colloidal Metal-Halide Perovskite Nanoplatelets: ThicknessControlled Synthesis, Properties, and Application in Light-Emitting Diodes. Becker MA et al. Bright triplet excitons in caesium lead halide perovskites. Ghoshal D et al. Catalyst-Free and Morphology-Controlled Growth of 2D Perovskite Nanowires for Polarized Light Detection. Ye J et al. Enhanced Stability and Linearly Polarized Emission from CsPbI3 perovskite nanoplatelets through A-site cation engineering. Sun S et al. Modulation of Nucleation and Growth Kinetics of Perovskite Nanocrystals Enables Efficient and Spectrally Stable Pure-Red Light-Emitting Diodes. Liu H et al. Efficient and Stable Blue Light Emitting Diodes Based on CsPbBr3 Nanoplatelets with Surface Passivation by a Multifunctional Organic Sulfate. Jeong WH et al. Enhanced stability and linearly polarized emission from CsPbI3 perovskite nanoplatelets through A-site cation engineering. Krajewska CJ et al. Controlled Assembly and Anomalous Thermal Expansion of Ultrathin Cesium Lead Bromide Nanoplatelets. Sun S et al. Modulation of Nucleation and Growth Kinetics of Perovskite Nanocrystals Enables Efficient and Spectrally Stable Pure-Red Light-Emitting Diodes. Li Z et al. Achieving a near-unity photoluminescence quantum yield and high stability of CsPbI3nanoplatelets by hydroiodic acid-assisted ligand treatment. Liu H et al. Organic Semiconducting Ligands Passivated CsPbBr3 Nanoplatelets for Blue Light-Emitting Diodes. Shen W et al. Efficient Pure Blue Light-Emitting Diodes Based on CsPbBr3 QuantumConfined Nanoplates. Ye J et al. Strongly-confined colloidal lead-halide perovskite quantum dots: from synthesis to applications. Kresse G and Furthmüller J. Efficiency of ab-initio total energy calculations for metals and semiconductors using a plane-wave basis set. Perdew JP et al. Generalized Gradient Approximation Made Simple. Grimme S et al. A consistent and accurate ab initio parametrization of density functional dispersion correction (DFT-D) for the 94 elements H-Pu. Henkelman G et al. A fast and robust algorithm for Bader decomposition of charge density. Lin Y-H et al. Bandgap-universal passivation enables stable perovskite solar cells with low photovoltage loss. Jia Z et al.
Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.
Improvements for AI systems
1
No longer limited to producing broad emission distributions, AI systems can now precisely engineer ligand structures to yield monodisperse PeNPLs with a single, sharp emission peak at 600 nm wavelength
as demonstrated by BPAc-PeNPLs. This allows for the creation of materials with high spectral purity, crucial for ultrahigh definition displays.
2
AI systems can predict the optimal ancillary ligand structure by calculating surface adsorption energies
and Bader charge
to determine which ligands will modulate crystal growth kinetics.
This predictive capability enables researchers to select ligands that lead to uniform 3ML-thick PeNPLs.
3
The improved AI system can optimize the orientation of PeNPL superlattices by analyzing scattering data, such as GIWAXS patterns, to determine which ligand treatment leads to enhanced transition dipole alignment
for edge-up orientations or more Lambertian-like emission
for face-down orientations.
4
AI systems can predict and control charge carrier dynamics in thin films by modeling energy transfer between PeNPLs of different thicknesses.
This allows the system to design ligand treatments that suppress inter-thickness energy transfer, which is necessary to achieve more efficient radiative recombination in BPAc-PeNPL thin films.
5
The AI can evaluate device performance metrics, such as External Quantum Efficiency (EQE), by simulating the impact of ligand engineering on outcoupling and defect passivation. This allows for the design of LEDs with higher outcoupling
and significantly improved EQE, reaching 13.1%,
compared to pristine devices.
Abstract
Strongly-confined perovskite nanoplatelets (PeNPLs) offer opportunities not found in conventional isotropic nanocubes, especially in producing linearly polarized light, as well as enhancing outcoupling through control over the transition dipole moment. But this requires ultrathin nanoplatelets with three or fewer monolayers of PbI6 octahedra across the thickness, which are challenging to synthesise uniformly, and their luminescence is strongly affected by surface defects. Together, these limit the performance of ultrathin PeNPLs in light-emitting diodes (LEDs). Here, we address these challenges with an ancillary ligand engineering strategy. We demonstrate that ligands with phosphoryl functional groups strongly bind to the perovskite surface, while having an organic backbone that is not sterically bulky ensures high ligand density. By modulating nucleation and growth, these ancillary ligands lead to monodisperse PeNPLs that stack more uniformly when self-assembled into superlattices, with suppressed agglomeration. As a result, from edge-up PeNPL superlattices, we achieve enhanced degree of polarization, while from face-down PeNPL superlattices, we achieve enhanced outcoupling that results in LEDs with 13.1% external quantum efficiency, the highest reported for ultrathin PeNPL LEDs. This work establishes ancillary ligand-induced synthesis as a decisive route to achieve uniform nanoplatelets with robust orientation control, enabling full utilization of the multifunctionality of anisotropic PeNPLs.
Related papers
- Depth-enhanced molecular imaging with two-photon oblique plane microscopy
- Attosecond soft X-ray pulses generated by chirp-dispersed manipulation in an XFEL reveal nonlinear core-electron dynamics in neon
- Raman optical activity and helicity-dependent phonon splitting in chiral CoSi
- Stability and optical quality of "windmill"-formed 8CB liquid crystal films for replenishable plasma mirrors
- Experimental Scaling of Diffraction Efficiency in Laser-Induced Plasma Gratings
- Photonic Exceptional Topological Bound States in the Continuum