Improved Modeling of Quasi-Static Thermal and Optical Response of Lumped-Element Aluminum Manganese KIDs

arXiv:2511.08959 · astro-ph.IM, physics.ins-det · Submitted 2025-11-12 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Astrophysics. The day in astrophysics: observations, models and what the data forces.

Vera: We're looking at the paper: "Improved Modeling of Quasi-Static Thermal and Optical Response of Lumped-Element Aluminum Manganese KIDs".

Paper summary: Vera: So, to wrap up this paper, we have this study by Adriana Gavidia et al. titled Improved Modeling of Quasi-Static Thermal and Optical Response of Lumped-Element Aluminum Manganese KIDs. What they did was apply a numerical model to optical data in order to constrain the optical efficiency of these devices.

Jocelyn: They found that although the model adequately described the data, they were unable to obtain useful constraints on the optical efficiency because their device response to optical load is small in the two hundred fifty millikelvin to three hundred fifty millikelvin regime.

Subrahmanyan: And they also noted that a key property of AlMn is that its transition temperature is lower than that of aluminum, which they highlighted as a distinct physical characteristic.

Vera: So, the main conclusion here is that the numerical implementation of Mattis-Bardeen theory vastly improves the quality of fit to fractional frequency shift versus temperature measurements for their AlMn resonators.

Jocelyn: That means we have a much better way to model how these detectors respond thermally and optically than they did with earlier analytical approximations.

Subrahmanyan: And this improved modeling is important because it gives us a more reliable theoretical basis for understanding the noise and response of the instruments that are going to be used for studying things like galaxy evolution via the Sunyaev-Zeldovich effect.

Vera: So, even though they can't get precise numbers on optical efficiency right now because of that small response, they've shown their numerical approach is a good tool for getting the physics right.

Jocelyn: It’s about showing that the math works for these specific materials and temperatures before you try to use it to constrain every single physical parameter like optical efficiency.

Conclusion: Vera: So, we've seen how they used this new numerical model to fit their Al Manganese kinetic inductance detector data really well across different temperatures and optical loads.

Jocelyn: It sounds like they are finally getting a much clearer picture of how these detectors actually behave when you look at them from an optical standpoint.

Subrahmanyan: The core idea here is that the numerical approach to the Mattis-Bardeen theory just works better than the old analytical approximations for modeling the material's response.

Vera: Exactly, and they found that this numerical fit quality improved by a factor of fifty when compared to just using those analytical methods.

Jocelyn: That means when we look at their results, we can trust them a lot more because the mathematical description matches the actual measurements way better now.

Subrahmanyan: It moves us closer to actually using these Al Manganese detectors for real science, like studying how galaxies evolve, because our theoretical models are getting tighter.

Vera: But they also pointed out a limitation, which is important—they couldn't get really tight constraints on the optical efficiency because the detector just doesn't react strongly enough in that specific temperature range.

Jocelyn: So we have a good model for the physics, but right now we can’t pin down exactly how efficient their light detection is without better experimental conditions.

Subrahmanyan: This study shows us that when you combine high-quality numerical theory with real detector measurements, you get a much more robust tool for understanding these superconducting materials.

Vera: It's a solid piece of work showing the power of moving away from simplified math in this kind of physics.

Jocelyn: Next up, we're going to look at what happens when we try to scale these concepts up and see if they hold true for other materials like Aluminum or maybe even something else entirely.

Division of Physics, Mathematics, and Astronomy at California Institute of Technology · Jet Propulsion Laboratory at California Institute of Technology · Institute of High Energy Physics at Chinese Academy of Sciences · Shanghai Normal University · National Astronomical Observatories of China · University of the Chinese Academy of Sciences

astro-ph.IM, physics.ins-det

Submitted: 2025-11-12

Updated: 2025-11-12

DOI: 10.1109/TASC.2026.3692397

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 82/100

The gist: We report on the optical characterization of AlMn kinetic inductance detectors (KIDs) in development for use in the Next-generation Extended Wavelength-MUltiband Sub/millimeter Inductance Camera…

Key concepts

Kinetic Inductance Detectors (KIDs)
These are superconducting devices that measure microwave frequencies by detecting changes in kinetic inductance when an external magnetic field is applied. They are being developed for high-frequency applications like the NEW-MUSIC camera.
BCS Theory
This is a theoretical framework used to describe the behavior of conventional superconductors, explaining how electrons pair up and form a superconducting state. The authors refined this theory by removing analytical shortcuts to better model AlMn's complex conductivity.
Gap Smearing Parameter
This is an extension added to BCS theory used for materials with high kinetic inductance. It accounts for the slight broadening of the superconducting energy gap, which was previously missing in simpler models. Testing this parameter did not improve the fits.
Mattis-Bardeen Theory
This theory links the quasi-particle density of a thin superconducting film to its surface impedance, helping determine how a superconductor reacts to changes in temperature and external loads like optical radiation.

Terminology

Summary

We report on the optical characterization of AlMn kinetic inductance detectors (KIDs) in development for use in the Next-generation Extended Wavelength-MUltiband Sub/millimeter Inductance Camera (NEW-MUSIC) [1] on the Leighton Chajnantor Telescope (LCT). p. 0

Where the paper says it

Frez2 , Xiaolan Huang3, 4, Junhan Kim1, 6, Jean-Marc Martin1 , Jack Sayers1 , Shibo Shu3 , Shiling Yu1, 5, 7, and Yann Sadou1 1Division of Physics, Mathematics, and Astronomy, California Institute of Technology, Pasadena, CA, USA, 91125 2 Jet Propulsion Laboratory, California Institute of Technology, 4800 Oak Grove Ave. , Pasadena, CA, USA, 91109 3 Institute of High Energy Physics, Chinese Academy of Sciences, Beijing, China, 100049 4Shanghai Normal University, Shanghai, China, 201418 5National Astronomical Observatories of China, Beijing, China, 100101 6Korea Advanced Institute for Science and Technology, Daejeon, 34141, Republic of Korea 7University of the Chinese Academy of Sciences, Beijing, China, 101408 Abstract—We report on the optical characterization of the AlMn kinetic inductance detectors (KIDs) in development for use in the Next-generation Extended Wavelength-MUltiband Sub/millimeter Inductance Camera (NEW-MUSIC) [1] on the Leighton Chajnantor Telescope (LCT).

Material Suitability and Modeling Improvements

AlMn is a promising candidate for the 10 GHz band because Al’s pair-breaking energy is too high, and AlMn can be fabricated with nearly identical processing as pure Al and allows for control of the Tc with varying levels of Mn doping Films of this material have been shown to have a slight broadening of the superconducting gap which is not accounted for within the BCS Mattis-Bardeen model employed. To improve modeling, the authors eliminated analytical approximations for expressions of complex conductivity and found these changes reduced fit parameter degeneracy in the analysis of AlMn. p. 0

Where the paper says it

To this end, we first improved the modeling techniques used for Al KIDs within BCS theory by eliminating the use of analytical approximations for the expressions of the complex conductivity and found these changes reduced fit parameter degeneracy in the analysis of AlMn. Then, we tested the addition of a gap smearing parameter, a standard extension to BCS theory in use for high kinetic inductance materials, and found it did not improve the fits.

They also tested the addition of a gap smearing parameter, a standard extension to BCS theory in use for high kinetic inductance materials, but found it did not improve the fits. p. 0
Where the paper says it

To this end, we first improved the modeling techniques used for Al KIDs within BCS theory by eliminating the use of analytical approximations for the expressions of the complex conductivity and found these changes reduced fit parameter degeneracy in the analysis of AlMn. Then, we tested the addition of a gap smearing parameter, a standard extension to BCS theory in use for high kinetic inductance materials, and found it did not improve the fits.

Theoretical Framework and Dark Scenario Calibration

The Mattis-Bardeen theory is used to determine the relationship between the quasi-particle density (nqp) of a thin superconducting film and its surface impedance. The fractional change in the complex conductivity in response to changes in nqp is defined as δσσ ≡ σ − σ0 σ0 = (κ1 − jκ2)nqp. p. 1

Where the paper says it

The imaginary component of the complex conductivity, σ2, approaches a constant value of σ dark 2 (0) = (π∆0/ℏω)σn due to the kinetic inductance of Cooper pairs. So, we have σ0 = σ dark 1 (0) − jσ dark 2 (0) = −j π∆0 ℏω σn (5) and the fractional change in the complex conductivity is δσ |σ| ≡ σ − σ0 |σ0| = (κ1 − jκ2)nqp (6) where we defined κ1 ≡ σ1/(σ0nqp) and κ2 ≡ σ2/(σ0nqp).

In the dark scenario, Eq. p. 1
Where the paper says it

1/2 − 1 2Rτmax , (8) where δ fres = fres(Tbath, Tload + Texc) − f0, f0 = fres(Tbath = 0, Tload + Texc = 0), Tload is the temperature of the blackbody load placed in front of the vacuum window, Tbath is the temperature at the detector stage, Texc accounts for a fixed additional excess optical loading originating from the cryostat, nqp,th is the thermal quasi-particle density, α is the kinetic inductance fraction, ηopt is the total optical efficiency, ηpb is the pair-breaking efficiency, ∆ν is the detector bandwidth, V = 3224 µm3 is the KID inductor volume, nth is the thermal quasi-particle density, τmax = 400 µs is the maximum quasiparticle life time [15]–[17], R = 2∆ 2 0 /[N0τ0(kBTc) 3 ] is the recombination rate per unit density of quasi-particles, Tc is the critical temperature of the KID inductor material, and τ0 = 438 ns is the characteristic electron-phonon interaction time. In the dark scenario, Eq.

7 reduces to δ fres/ f0 = −α squared κ2nqp,th. p. 1
Where the paper says it

In the dark scenario, Eq. 7 reduces to δ fres f0 = − α 2 κ2nqp,th.

The authors used a vector network analyzer (VNA) to measure S 21(f) over the frequency range containing the resonances at a range of Tbath values with no optical loading (dark). p. 2
Where the paper says it

8, AUGUST 2021 3 B. Dark Scenario To calibrate the frequency response to changes in nqp,th, we use a vector network analyzer (VNA) to measure S 21(f) over the frequency range containing the resonances at a range of Tbath values, with no optical loading (dark).

This provided constraints on α and ∆0 by fitting Eq. p. 2
Where the paper says it

To compare with the analysis method employing analytical approximations, we also plot the fitted model obtained from such a technique in red. Note that the red and black data points are identical fres measurements, but their corresponding δ fres/ f0 curves differ because they are scaled by the f0 values obtained by their respective fitting techniques.

9 using a least squares minimization routine performing the complex conductivity integrals fully numerically. p. 2
Where the paper says it

9 using a least squares minimization routine, performing the complex conductivity integrals (Eqs. 1, 2, 4) fully numerically.

Numerical vs. p. 0

Where the paper says it

Before exploring models outside of BCS theory, we therefore first improve upon the modeling of the shift in frequency due to changes in quasi-particle density used for the Al devices in [1], which employed analytic approximations to obtain the complex conductivity within Mattis-Bardeen theory. Instead, we implement fully numerical models.

Analytic Modeling Performance

The numerical model was shown to vastly improve the quality of fit to fractional frequency shift vs. temperature measurements of AlMn resonators, now yielding satisfactory agreement. p. 3

Where the paper says it

1, 2, and 4) vastly improves the quality of fit to fractional frequency shift vs. temperature measurements of our AlMn resonators, now yielding satisfactory agreement.

The fit quality improved significantly in the numerical case by a factor of χ squared analytical/χ squared numerical ∼ 50. p. 2
Where the paper says it

Note that the red and black data points are identical fres measurements, but their corresponding δ fres/ f0 curves differ because they are scaled by the f0 values obtained by their respective fitting techniques. We see the fit quality improves significantly in the numerical case, by a factor of χ 2 analytical/χ2 numerical ∼ 50.

Furthermore, fits employing analytical approximations have a strong degeneracy between the recovered α and ∆0 values for all resonators, whereas the recovered parameters from the numerical fits display no such degeneracy. p. 2
Where the paper says it

Additionally, the fits employing analytical approximations have a strong degeneracy between the recovered α and ∆0 values for all the resonators, as shown by the purple data points in Figure 2. Conversely, the recovered α and ∆0 parameters from the numerical fits, shown as green data points, display no such degeneracy.

Including a gap broadening term degraded the χ squared of the numerical analysis by a factor of ∼6, leading them not to include it in the results. p. 2
Where the paper says it

1, 2, and 4, where Γ is an additional free parameter in the fit. Including this effect in our modeling degraded the χ 2 of the numerical analysis by a factor of ∼6, so we did not include it in the results presented here.

Optical Constraints and Limitations

The optical efficiency was constrained by fitting measurements taken with alternating beam filling black body load cooled to liquid nitrogen (Tload = 77.36 K) and ambient, room temperature black body load (Tload = 294. p. 2

Where the paper says it

Optical Scenario We measured the optical efficiency of our AlMn devices by performing the same S 21(f) scan, now alternating between a beam filling black body load cooled to the temperature of liquid nitrogen (Tload = 77. 36 K), denoted by “cold”, and an ambient, room temperature black body load (Tload = 294.

15 K). The Mattis-Bardeen fits constrained ηopt by Eq. p. 0
Where the paper says it

Then, we tested the addition of a gap smearing parameter, a standard extension to BCS theory in use for high kinetic inductance materials, and found it did not improve the fits. Index Terms—Kinetic inductance detectors, Mattis-Bardeen theory, gap smearing I.

8, but this parameter was completely degenerate with several other parameters. p. 2
Where the paper says it

The MattisBardeen fits to this data constrain ηopt (Eq. 8), however, we note that this parameter is completely degenerate with several other parameters: α, ∆0, ∆ν, ηpb, N0, R, and V.

The ability to constrain optical efficiency is limited because the response of the AlMn resonator to optical load is small in the 250-350 mK regime. p. 3
Where the paper says it

This numerical model was applied to optical data in order to constrain the optical efficiency of the devices. Although the model adequately described the data, we were unable to obtain useful constraints on the optical efficiency because the device response to optical load is small in the 250-350 mK regime.

The Tc of AlMn is lower than that of Al, and as shown in Figure 3, the device does not reach the steady state regime where optically generated quasi-particles dominate in this Tbath range. p. 3
Where the paper says it

As shown in Figure 3, we measure δ fres/ f0 over approximately the same range for Al and AlMn. The AlMn device does not reach the steady state regime where optically generated quasi-particles dominate in this Tbath range, which may imply, given the lower Tc of AlMn, we have not probed to low enough Tbath to enter the regime where this occurs for AlMn.

Conclusion on Modeling Sufficiency

The authors concluded that the numerical forms of the Mattis-Bardeen equations are sufficient to model δ fres/ f0 for AlMn. The primary factor believed to be responsible for the small response of AlMn is highlighted in their final assessment. p. 2

Where the paper says it

The small response of the AlMn resonator (compared to that of Al) prevented the fit from obtaining meaningful constraints on ηopt. The primary factor we believe is responsible for the small

The study demonstrates that the numerical implementation of Mattis-Bardeen theory vastly improves the quality of fit to fractional frequency shift vs. p. 3
Where the paper says it

Conclusion We have demonstrated that, relative to the analytic implementation, a numerical implementation of Mattis-Bardeen theory (Eqs. 1, 2, and 4) vastly improves the quality of fit to fractional frequency shift vs.

temperature measurements of their AlMn resonators. p. 3
Where the paper says it

1, 2, and 4) vastly improves the quality of fit to fractional frequency shift vs. temperature measurements of our AlMn resonators, now yielding satisfactory agreement.

The paper shows good agreement between the optical model and data in the low temperature regime, although they were unable to obtain useful constraints on ηopt due to small response. p. 3
Where the paper says it

This numerical model was applied to optical data in order to constrain the optical efficiency of the devices. Although the model adequately described the data, we were unable to obtain useful constraints on the optical efficiency because the device response to optical load is small in the 250-350 mK regime.

The Tc of AlMn is lower than that of Al. p. 0
Where the paper says it

76 kB Tc, too high to be suitable for band 1, whose lower edge is at ≈80 GHz. AlMn is a promising candidate for this band, as it can be fabricated with nearly identical processing as pure Al and allows for control of the Tc with varying levels of Mn doping [6] [7] [8].

p. 0
Where the paper says it

76 kB Tc, too high to be suitable for band 1, whose lower edge is at ≈80 GHz. AlMn is a promising candidate for this band, as it can be fabricated with nearly identical processing as pure Al and allows for control of the Tc with varying levels of Mn doping [6] [7] [8].

Acknowledgments

This work has been supported by the JPL Research and Technology Development Fund, the National Aeronautics and Space Administration under awards 80NSSC18K0385 and 80NSSC22K1556, the Department of Energy Office of HighEnergy Physics Advanced Detector Research program under award DE-SC0018126, and the Wilf Foundation.

References

[1] S. R. Golwala, A. p. 3

Where the paper says it

References [1] S. Golwala, A.

D. Beyer, D. Cunnane, P. p. 3
Where the paper says it

Golwala, A. Cunnane, P.

K. Day, F. Defrance, C. p. 3
Where the paper says it

Cunnane, P. Defrance, C.

F. Frez, X Huang, J Kim, J.-M Martin, J Sayers, S Shu and S Yu “NEW-MUSIC: The Next-generation Extended-Wavelength MUltiband Sub/millimeter Inductance Camera,” in Society of Photo-Optical Instrumentation Engineers (SPIE) Conference Series, ser. p. 3
Where the paper says it

Shu, and S. Yu, “NEW-MUSIC: The Next-generation Extended-Wavelength MUltiband Sub/millimeter Inductance Camera,” in Society of Photo-Optical Instrumentation Engineers (SPIE) Conference Series, ser.

Society of PhotoOptical Instrumentation Engineers (SPIE) Conference Series, J Zmuidzinas and J R Gao Eds. p. 3
Where the paper says it

Society of PhotoOptical Instrumentation Engineers (SPIE) Conference Series, J. Zmuidzinas and J.

p. 3
Where the paper says it

Society of PhotoOptical Instrumentation Engineers (SPIE) Conference Series, J. Zmuidzinas and J.

, vol. 13102, Aug. p. 3
Where the paper says it

Zmuidzinas and J. 13102, Aug.

p. 3
Where the paper says it

Zmuidzinas and J. 13102, Aug.

2024, p. 1310202

[5] S Hempel-Costello, A Beyer, P K Day, F Defrance, A Gavidia S R Golwala J M Martin Y Sadou J Sayers S Shu and S Yu “LowFrequency Noise Performance of Microstrip-Coupled Lumped-Element Aluminum KIDs using Hydrogenated Amorphous Silicon Parallel-Plate Capacitors for NEW-MUSIC,” this volume

[12] G Jones, B R Johnson, M H Abitbol P A R Ade S Bryan H M Cho P Day D Flanigan K D Irwin D Li P Mauskopf H McCarrick A Miller Y R Song and C Tucker “High quality factor manganese-doped aluminum lumped-element kinetic inductance detectors sensitive to frequencies below 100 GHz,” Applied Physics Letters, vol. 110, no. 22, p. 222601 May 2017

[4] X Huang S Shu and S R Liu F Golwala “Design of a Six-band, 2.5-Octave (75–420 GHz) Hierarchically Summed Phased-Array SlotDipole Antenna Array for NEW-MUSIC,” this volume

[13] D C Mattis and J Bardeen “Theory of the anomalous skin effect in normal and superconducting metals,” Phys. Rev., vol. 111, pp. 412–417 Jul 1958

[6] B A Young T Saab B Cabrera A J Miller P L Brink and J P Castle “Effect of implanted metal impurities on superconducting tungsten films,” Journal of Applied Physics, vol. p. 3

Where the paper says it

Golwala, “A Multi-chroic Kinetic Inductance Detectors Array Using Hierarchical Phased Array Antenna,” J. Physics, vol.

p. 3
Where the paper says it

Golwala, “A Multi-chroic Kinetic Inductance Detectors Array Using Hierarchical Phased Array Antenna,” J. Physics, vol.

p. 3
Where the paper says it

Golwala, “A Multi-chroic Kinetic Inductance Detectors Array Using Hierarchical Phased Array Antenna,” J. Physics, vol.

p. 3
Where the paper says it

Golwala, “A Multi-chroic Kinetic Inductance Detectors Array Using Hierarchical Phased Array Antenna,” J. Physics, vol.

91, no. 10, pp. 6516–6519, 05 2002

[7] B Young J Williams S Deiker S Ruggiero and B Cabrera “Using ion implantation to adjust the transition temperature of superconducting films,” Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment, vol. 520, no. 1, pp. 307–310, 2004

[8] S W Deiker W Doriese G C Hilton K D Irwin W H Rippard J N Ullom L R Vale S T Ruggiero A Williams and B A Young “Superconducting transition edge sensor using dilute almn alloys,” Applied Physics Letters, vol. 85, no. 11, pp. 2137–2139, 09 2004

[9] A B Kaiser “Effect of non-magnetic localized states in superconducting alloys,” Journal of Physics C: Solid State Physics, vol. 3, no. 2, p. 410, feb 1970

[10] G O’Neil D Schmidt N A Miller J N Ullom A Williams G B Arnold and S T Ruggiero “Observation of nonmagnetic resonant scattering effects by tunneling in dilute al-mn alloy superconductors,” Phys. Rev. Lett., vol. 100, no. 5, p. 056804, Feb. p. 3

Where the paper says it

Ruggiero, “Observation of nonmagnetic resonant scattering effects by tunneling in dilute al-mn alloy superconductors,” Phys. 056804, Feb.

2008

[11] G C O’Neil D R Schmidt N A Tomlin and J N Ullom “Quasiparticle density of states measurements in clean superconducting almn alloys,” Journal of Applied Physics, vol. 107, no. 9, p. 093903, 05 2010

[14] R E Glover and M Tinkham “Conductivity of superconducting films for photon energies between 0.3 and 40kTc,” Phys. p. 4

Where the paper says it

Tinkham, “Conductivity of superconducting films for photon energies between 0. 3 and 40kTc,” Phys.

Rev., vol. 108, pp. 243–256, Oct 1957

[15] A G Kozorezov A A Golubov J K Wigmore D Martin P Verhoeve R A Hijmering and I Jerjen “Inelastic scattering of quasiparticles in a superconductor with magnetic impurities,” Phys. Rev. B, vol. 78, p. 174501, Nov 2008

[16] R Barends J J A Baselmans S J C Yates J R Gao J N Hovenier and T M Klapwijk “Quasiparticle relaxation in optically excited highq superconducting resonators,” Phys. Rev. Lett., vol. 100, p. 257002, Jun 2008

[17] R Barends S van Vliet J J A Baselmans S J C Yates J R Gao and T M Klapwijk “Enhancement of quasiparticle recombination in ta and al superconductors by implantation of magnetic and nonmagnetic atoms,” Phys. Rev. B, vol. 79, p. 020509, Jan 2009

[18] J Gao “The physics of superconducting microwave resonators,” Ph.D. dissertation, California Institute of Technology, Pasadena, California, USA, 2008

[19] T Guruswamy D J Goldie and S Withington “Quasiparticle generation efficiency in superconducting thin films,” Superconductor Science Technology, vol. 27, no. 5, p. 055012, May 2014

[20] B A Mazin “Microwave kinetic inductance detectors,” Ph.D. dissertation, California Institute of Technology, Pasadena, California, USA, 2005

[3] J M Martin J Kim F Defrance S Shu A D Beyer P K Day J Sayers and S R Golwala “Hierarchical Phased-Array Antennas Coupled to Al KIDs: A Scalable Architecture for Multi-band Millimeter/Submillimeter Focal Planes,” J. Low Temp. Physics, vol. 216, pp. 104–111, 2024

[2] S Shu A Beyer P Day F Defrance J Sayers and S Golwala “A Multi-chroic Kinetic Inductance Detectors Array Using Hierarchical Phased Array Antenna,” J. Low Temp. Physics, vol. 209, pp. 330–336, 2022

[1] S R Golwala A D Beyer D Cunnane P K Day F Defrance C F Frez X Huang J Kim J M Martin J Sayers S Shu and S Yu “NEW-MUSIC: The Next-generation Extended Wavelength-MUltiband Sub/millimeter Inductance Camera,” in Society of PhotoOptical Instrumentation Engineers (SPIE) Conference Series, ser. Society of PhotoOptical Instrumentation Engineers (SPIE) Conference Series, J Zmuidzinas and J R Gao Eds., vol. 13102, Aug. 2024, p. 1310202

[5] S Hempel-Costello A Beyer P K Day F Gavidia S R Golwala J M Martin Y Sadou J Sayers S Shu and S Yu “LowFrequency Noise Performance of Microstrip-Coupled Lumped-Element Aluminum KIDs using Hydrogenated Amorphous Silicon Parallel-Plate Capacitors for NEW-MUSIC,” this volume

[12] G Jones B R Johnson M H Abitbol P A R Ade S Bryan H M Cho P Day D Flanigan K D Irwin D Li P Mauskopf H McCarrick A Miller Y R Song and C Tucker “High quality factor manganese-doped aluminum lumped-element kinetic inductance detectors sensitive to frequencies below 100 GHz,” Applied Physics Letters, vol. 110, no. 22, p. 222601 May 2017

[3] J M Martin J Kim F Defrance S Shu A D Beyer P K Day J Sayers and S R Golwala “Hierarchical Phased-Array Antennas Coupled to Al KIDs: A Scalable Architecture for Multi-band Millimeter/Submillimeter Focal Planes,” J. Low Temp. Physics, vol. 216, pp. 104–111, 2024

[4] X Huang S Shu and S R Liu F Golwala “Design of a Six-band, 2.5-Octave (75–420 GHz) Hierarchically Summed Phased-Array SlotDipole Antenna Array for NEW-MUSIC,” this volume

[13] D C Mattis and J Bardeen “Theory of the anomalous skin effect in normal and superconducting metals,” Phys. Rev., vol. 111, pp. 412–417 Jul 1958

[260] Figure 3 shows this for an AlMn resonator and on the right is for an Al resonator

[3] The paper is titled Improved Modeling of Quasi-Static Thermal and Optical Response of Lumped-Element Aluminum Manganese KIDs

Conclusion

The numerical model was applied to optical data in order to constrain the optical efficiency of the devices. p. 3

Where the paper says it

Additionally, we found that, when we included a gap broadening term in our model, the fit quality degraded, implying that our AlMn films do not suffer noticeable gap smearing. This numerical model was applied to optical data in order to constrain the optical efficiency of the devices.

Although the model adequately described the data, they were unable to obtain useful constraints on the optical efficiency because the device response to optical load is small in the 250-350 mK regime. p. 3
Where the paper says it

This numerical model was applied to optical data in order to constrain the optical efficiency of the devices. Although the model adequately described the data, we were unable to obtain useful constraints on the optical efficiency because the device response to optical load is small in the 250-350 mK regime.

The Tc of AlMn is lower than that of Al. The numerical model was applied to optical data in order to constrain the optical efficiency of the devices.

[3] J M Martin J Kim F Defrance S Shu A D Beyer P K Day J Sayers and S R Golwala “Hierarchical Phased-Array Antennas Coupled to Al KIDs: A Scalable Architecture for Multi-band Millimeter/Submillimeter Focal Planes,” J. Low Temp. Physics, vol. 216, pp. 104–111, 2024

[5] S Hempel-Costello A Beyer P K Day F Gavidia S R Golwala J M Martin Y Sadou J Sayers S Shu and S Yu “LowFrequency Noise Performance of Microstrip-Coupled Lumped-Element Aluminum KIDs using Hydrogenated Amorphous Silicon Parallel-Plate Capacitors for NEW-MUSIC,” this volume

[12] G Jones B R Johnson M H Abitbol P A R Ade S Bryan H M Cho P Day D Flanigan K D Irwin D Li P Mauskopf H McCarrick A Miller Y R Song and C Tucker “High quality factor manganese-doped aluminum lumped-element kinetic inductance detectors sensitive to frequencies below 100 GHz,” Applied Physics Letters, vol. 110, no. 22, p. 222601 May 2017

[4] X Huang S Shu and S R Liu F Golwala “Design of a Six-band, 2.5-Octave (75–420 GHz) Hierarchically Summed Phased-Array SlotDipole Antenna Array for NEW-MUSIC,” this volume

[13] D C Mattis and J Bardeen “Theory of the anomalous skin effect in normal and superconducting metals,” Phys. Rev., vol. 111, pp. 412–417 Jul 1958

[260] Figure 3 shows this for an AlMn resonator and on the right is for an Al resonator

[3] The paper is titled Improved Modeling of Quasi-Static Thermal and Optical Response of Lumped-Element Aluminum Manganese KIDs

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved Modeling of AlMn KIDs can accurately predict detector response by using fully numerical models for complex conductivity integrals instead of analytical approximations, as this vastly improves the quality of fit to fractional frequency shift vs. temperature measurements.

  2. The improved AI system can constrain optical efficiency by using a model given by Eq. 7 and fitting it to hot and cold load data, although the paper notes that the small response of the AlMn resonator (compared to that of Al) prevented the fit from obtaining meaningful constraints on ηopt.

  3. The system can be used to determine if AlMn films suffer from gap smearing by testing a gap broadening term in the fits; however, including this term degraded the chi two of the numerical analysis by a factor of ~6, suggesting it should not be included for current results.

Abstract

We report on the optical characterization of the AlMn kinetic inductance detectors (KIDs) in development for use in the Next-generation Extended Wavelength-MUltiband Sub/millimeter Inductance Camera (NEW-MUSIC) on the Leighton Chajnantor Telescope (LCT). NEW-MUSIC will cover 80-420 GHz, split into six spectral bands, with polarimetry. This broad spectral coverage will enable study of a range of scientific topics such as the accretion and feedback in galaxies and galaxy cluster evolution via the Sunyaev-Zeldovich effect, the transient synchrotron emission from the explosive deaths of massive stars and other time-domain phenomena, and dusty sources from low to high redshift (with polarization). Al KIDs have already been demonstrated for bands 2-5. AlMn KIDs will be used for the 90 GHz band, as Al's pair-breaking energy is too high. However, AlMn has only barely been explored as a KID material. To this end, we first improved the modeling techniques used for Al KIDs within BCS theory by eliminating the use of analytical approximations for the expressions of the complex conductivity and found these changes reduced fit parameter degeneracy in the analysis of AlMn. Then, we tested the addition of a gap smearing parameter, a standard extension to BCS theory in use for high kinetic inductance materials, and found it did not improve the fits.

Related papers