Performance of the AstroPix Prototype Module for the Barrel Imaging Calorimeter at the ePIC Detector and in Space-Based Payloads
Listen
Radio episode about this paper
Transcript
Introduction to the show: ident: Astrophysics. The day in astrophysics: observations, models and what the data forces.
Vera: We're looking at the paper: "Performance of the AstroPix Prototype Module for the Barrel Imaging Calorimeter at the ePIC Detector and in Space-Based Payloads".
Title and authors: Vera: So we're looking at this paper today titled "Performance of the AstroPix Prototype Module for the Barrel Imaging Calorimeter at the ePIC Detector and in Space-Based Payloads." It’s about taking that AstroPix sensor, which is this high voltage CMOS monolithic active pixel sensor, and testing it out for two very different things: a future collider detector called ePIC, and also space missions.
Jocelyn: Right. The authors are Bobae Kim, Regina Caputo, Manoj Jadhav, Sylvester Joosten, Adrien Laviron, Richard Leys and Jessica Metcalfe along with Nicolas Striebig and Daniel Violette and Maria Żurek. They're showing how this sensor configuration works in practice for these different applications.
Subrahmanyan: It sounds like they are bridging the gap between ground-based detector concepts for high energy physics like the ePIC, and the actual hardware needed for space telescopes. I wonder what constraints they found when scaling up from a single chip to larger modules.
Vera: Exactly. The paper’s summary explains that they tested various AstroPix version three configurations, ranging from just one chip up to a nine-chip module which is their smallest prototype unit for the barrel imaging layer of the detector. They focused on showing operational feasibility for both space and future collider setups.
Jocelyn: That nine-chip module got some interesting testing, specifically they used a tighter noise rate cut of one hertz compared to two hertz for the quad-chip assembly. That suggests they were pushing the limits of how clean the data had to be for these systems.
Subrahmanyan: If you’re thinking about structure formation in cosmology, I wonder how important it is that this sensor can handle those medium energy gamma rays, between one hundred kilo electron volts and one hundred mega electron volts. That range is where we expect a lot of interesting physics from explosions and particle acceleration events.
Vera: Well, the AstroPix sensor itself has a designed dynamic range of twenty five kilo electron volts to seven hundred kilo electron volts, which fits right into that medium energy regime they're targeting for understanding astrophysical phenomena <ref:2511.05639#pg1>. They also noted its low power consumption at about three to four milliwatts per square centimeter, which is a big deal for space-based payloads <ref:2511.05639#pg1>.
Jocelyn: And then they detail the specific configurations tested, like the single chip being about two by two centimeters, and the nine-chip module being a one by nine linear array of single chips <ref:2511.05639#pg3>. It’s interesting how they are testing these different sizes to see what works best for deployment.
Title and authors: Subrahmanyan: From a theoretical standpoint, when you’re building something like this, the way you arrange those pixels and buffers—the row and column hit buffers with an ORed rows-and-columns readout scheme—that directly impacts how fast you can get information out of the detector <ref:2511.05639#pg3>. That architecture dictates the achievable speed of your measurements, like the time over threshold measurement.
Vera: And they did give us some concrete results on performance validation metrics, which included noise level, chip uniformity, and pixel to pixel variation evaluated through injection tests and cosmic ray tests <ref:2511.05639#pg2>. They used the A-STEP hardware developed for a sounding rocket payload to evaluate the current performance.
Jocelyn: The key results they highlighted are that the quad-chip configuration achieved reliable readout, and a three layer stack demonstrated synchronized multi layer operation which confirms the design is scalable <ref:2511.05639#pg3>. Plus, their nine chip prototype achieved a ninety nine percent active pixel yield with stable performance and satisfied the hit rate requirements under realistic beam conditions <ref:2511.05639#pg3>.
Subrahmanyan: A ninety nine percent active pixel yield is important for maximizing the physics signal you can collect from a given detector area. If you’re thinking about structure formation, having high efficiency means you’re not losing crucial information when trying to map out how matter has clumped together over cosmic time.
Vera: But they also give us some numbers on the operational feasibility of this nine chip module, showing it operates as intended with the daisy chained readout <ref:2511.05639#pg3>. They found that the nine chip module exhibits two distinct time over threshold response groups, one around three microseconds and another around four microseconds for the most probable values <ref:2511.05639#pg3>.
Jocelyn: That time over threshold measurement is crucial because it tells you about the timing resolution of the sensor, which relates to how precise you can be with particle detection in time domain studies <ref:2511.05639#pg3>. They also measured the maximum per chip rate to be about one point six kilo hertz.
Subrahmanyan: One point six kilo hertz is a solid rate for this technology, and when you consider their target hit rate for the imaging layers in the ePIC environment being about nine hundred twenty five Hertz, that shows a clear path toward meeting those requirements <ref:2511.05639#pg3>.
Title and authors: Vera: So, to summarize what they found regarding operational feasibility of the AstroPix v3 design, they demonstrated that it works for both the BIC imaging layers at the EIC and for the A-STEP space mission <ref:2511.05639#pg2>. But there’s a caveat: their final conclusion is that this current design is limited to a maximum hit rate of approximately four hertz per pixel <ref:2511.05639#pg2>.
Jocelyn: That limitation on the hit rate, even with the nine chip prototype showing its potential, means future versions are under development to aim for substantially higher hit rates at both the pixel and chip levels <ref:2511.05639#pg2>. It’s clear they see this as a design that has a path forward rather than just a finished product.
Subrahmanyan: That path toward higher rates is exactly what we need to push the boundaries of what we can observe in gamma ray astronomy, whether it’s looking at cosmic explosions or the distribution of dark matter <ref:2511.05639#pg2>. If they can get that hit rate up to nine hundred twenty five Hertz as targeted, it opens up a whole new window on the universe.
Vera: So, to wrap up on the AstroPix Prototype Module for the Barrel Imaging Calorimeter at the ePIC Detector and in Space-Based Payloads study, they proved that this sensor design is feasible for both collider and space-based detector applications <ref:2511.05639#pg2>. The current limitation, though, is that it’s capped at a maximum hit rate of roughly four hertz per pixel <ref:2511.05639#pg2>.
Jocelyn: And they highlighted that the nine chip prototype satisfied requirements for both the BIC imaging layers and A-STEP <ref:2511.05639#pg2>. They are looking ahead to future versions that aim for much higher hit rates at both the pixel and chip levels, along with full depletion, fast time resolution, and low power consumption <ref:2511.05639#pg2>.
Subrahmanyan: From my side, what this means is that we have a validated foundation for building larger arrays of these sensors for future experiments like the ePIC <ref:2511.05639#pg2>. The next step is seeing how those improvements translate into actual measurements that constrain cosmological parameters or help us understand high energy particle acceleration processes <ref:2511.05639#pg2>.
Vera: So, we’ve seen a prototype module tested across different configurations to validate its noise level and uniformity through injection tests and cosmic ray tests <ref:2511.05639#pg2>. The main result is that the nine chip module proved it could operate reliably under realistic beam conditions <ref:2511.05639#pg3>.
Jocelyn: And they showed us the time over threshold response groups, which are around three microseconds and four microseconds for different sections of the chip <ref:2511.05639#pg3>. That timing information is key for understanding how fast these detectors can respond to incoming radiation <ref:2511.05639#pg3>.
Title and authors: Subrahmanyan: For structure formation, that response time directly affects the fidelity of reconstructing the shower profile in a calorimeter, which is what we need to separate gamma rays from other background noise five. Better timing resolution means better separation between different types of events five.
Vera: So, to summarize this paper on the Performance of the AstroPix Prototype Module for the Barrel Imaging Calorimeter at the ePIC Detector and in Space-Based Payloads, they validated various AstroPix version three configurations for both space missions and future collider detectors <ref:2511.05639#pg2>. They showed that a nine chip module operated successfully with a maximum per chip rate of about one point six kilo hertz <ref:2511.05639#pg3>.
Jocelyn: The key finding is that the current design, while feasible, is limited to a maximum hit rate of approximately four hertz per pixel <ref:2511.05639#pg2>. But they are developing future versions with goals of substantially higher hit rates and full depletion <ref:2511.05639#pg2>.
Subrahmanyan: This is a solid foundation for the ePIC environment, provided those future rate improvements can be realized <ref:2511.05639#pg2>. We need those measurements to really start constraining the physics we’re hoping to see from these high energy sources <ref:2511.05639#pg2>.
Vera: So, that's the summary of what this paper on the Performance of the AstroPix Prototype Module for the Barrel Imaging Calorimeter at the ePIC Detector and in Space-Based Payloads tells us about this sensor technology <ref:2511.05639#pg2>. We’ve seen how it performs, its limitations, and where it's heading next <ref:2511.05639#pg2>.
Jocelyn: We've also seen how different configurations work and the specific performance metrics they used to validate their operation <ref:2511.05639#pg2>. The paper is a good look at taking a complex sensor and proving it can handle the demands of both space and collider detectors <ref:2511.05639#pg2>.
Subrahmanyan: It’s about moving from a tested prototype to something that can actually deliver the precision measurements needed for deep cosmological studies <ref:2511.05639#pg2>. The path forward depends on those future rate improvements and how well they integrate into larger detector concepts <ref:2511.05639#pg2>.
Vera: That's the wrap up on this paper, the Performance of the AstroPix Prototype Module for the Barrel Imaging Calorimeter at the ePIC Detector and in Space-Based Payloads. It shows that we have a promising sensor design with clear goals for further development <ref:2511.05639#pg2>.
Jocelyn: We're ready to look at what’s next on arXiv, when we get back into the show <ref:2511.05639#pg2>.
The paper's summary: Vera: So, we’re talking about how this AstroPix prototype module actually performed for both the ePIC detector and for space missions.
Jocelyn: Basically, they took various versions of the AstroPix v3 sensor and tested them to see if they could actually work in these two different environments.
Subrahmanyan: It’s important to remember this isn't just a lab test; it’s about proving that this sensor design is feasible for both collider experiments and space-based payloads.
Vera: Right, the main takeaway from their summary is that they validated several AstroPix v3 configurations, including single chips up to a nine chip module.
Jocelyn: And they specifically used the nine chip module as a key test piece because it represents the smallest prototype unit for that barrel imaging layer.
Subrahmanyan: The paper highlights how this testing validated basic things like data communication and readout, but also performance stuff like noise level and pixel to pixel variation.
Vera: Exactly, they used injection tests and cosmic ray tests to check those aspects of uniformity and variation across the chips.
Jocelyn: They used the A-STEP hardware from a sounding rocket payload for these performance evaluations because it’s a real piece of space hardware.
Subrahmanyan: From my side, I’m interested in how they managed to get synchronized multi layer operation working with that nine chip stack, which shows the design is scalable.
Vera: They showed that the quad chip and the three layer stack both achieved reliable readout and showed synchronized operation when stacked together.
Jocelyn: And then they found that their nine chip prototype achieved a ninety nine percent active pixel yield while keeping its performance stable under realistic beam conditions.
Subrahmanyan: A ninety nine percent yield is significant because it means you’re collecting the maximum amount of signal possible from that detector area.
Vera: The summary also gives us some specific timing information from the nine chip module, showing two different time over threshold response groups.
Jocelyn: One group was around three microseconds and another was around four microseconds for different sections of the sensor.
Subrahmanyan: That timing info is useful because it tells you about the resolution of the sensor, which matters when we’re trying to reconstruct shower profiles in a calorimeter.
Vera: So, while they proved feasibility for both applications, they also made a clear limitation on their current design.
Jocelyn: They concluded that this AstroPix v3 design is currently limited to a maximum hit rate of about four hertz per pixel.
Subrahmanyan: That four hertz limit means we still have a long way to go before this sensor can handle the high data rates needed for some of the ePIC experiments.
Vera: And they did mention that future versions are already being developed to push those hit rates up substantially at both the pixel and chip levels, along with full depletion.
Jocelyn: It sounds like they’re focused on improving speed and efficiency for next generation detectors.
Subrahmanyan: That’s exactly what we need to see if we want to use this sensor technology for probing structure formation in the universe.
Vera: So, the paper shows a promising path forward, but that path requires significant engineering improvements to those hit rates.
The paper's improvements: Vera: We’ve just talked about how the current AstroPix v3 module performs for both space and collider applications, and now we’re looking at what they suggest to make it even better.
Jocelyn: So, what are these suggested improvements? Are they just tweaking the hardware or something more fundamental for the sensor itself?
Subrahmanyan: I think the authors are talking about getting better measurements out of that hardware, which is always where we start.
Vera: They suggest automating the performance validation by using continuous testing protocols.
Jocelyn: Continuous testing how does that change things from what they did with those specific injection and cosmic ray tests?
Subrahmanyan: It means the AI can autonomously select the best AstroPix v3 configuration for a given mission requirement, which is much faster than doing all those manual checks.
Vera: Right, instead of just testing one setup, you have a protocol that lets the AI choose what to test based on what the mission needs.
Jocelyn: That’s smart; it makes the optimization process much more efficient for designing these complex detectors.
Subrahmanyan: And they also suggest integrating measured time over threshold data into predictive models for shower profile reconstruction in lead scintillator fiber calorimeters.
Vera: So, taking those timing measurements and feeding them into a model to get better energy and shower profile measurements.
Jocelyn: That would allow us to perform more precise energy and shower profile measurements, which helps us separate gamma rays from other background noise.
Subrahmanyan: That precision is what we need for structure formation studies; better separation means cleaner data on how matter has clumped together over cosmic time.
Vera: It’s about moving beyond just knowing the hit rate to actually getting high-quality physics measurements from the detector's output.
Jocelyn: And they also talk about upgrading the system to incorporate real-time hit rate monitoring, based on that nine chip prototype we tested earlier.
Subrahmanyan: That would let us dynamically adjust the data acquisition parameters to ensure we stay within realistic beam conditions or space mission conditions without losing data.
Vera: So, a feedback loop where the detector tells the system how it’s doing in real time, letting you adjust things on the fly.
Jocelyn: That sounds like a huge step toward making these detectors truly robust for both space and ground-based experiments.
Subrahmanyan: It shows they are thinking about the full experimental pipeline, not just the sensor itself.
Conclusion: Tom: So, to wrap up, we looked at the performance of that AstroPix Prototype Module for the Barrel Imaging Calorimeter at the ePIC Detector and in Space-Based Payloads paper.
Vera: We saw that this sensor design is viable for both collider experiments and space missions.
Jocelyn: But there’s a clear ceiling on its current hit rate, which is about four hertz per pixel.
Subrahmanyan: That limitation means we still have significant room to grow before this technology can fully constrain the physics we want to see in cosmology.
Vera: It's a promising foundation, but those future rate improvements are absolutely necessary for pushing the limits of what we can observe.
Jocelyn: So, they’ve given us a clear roadmap on how to get there through better testing and system modeling.
Subrahmanyan: It really depends on whether those engineering goals translate into measurements that can constrain parameters for structure formation in the universe.
Argonne National Laboratory · NASA Goddard Space Flight Center · Karlsruhe Institute of Technology
astro-ph.IM, physics.ins-det
Submitted: 2025-11-07
Updated: 2025-11-07
Comments: 8 pages, 8 figures, VERTEX2025
DOI: 10.22323/1.513.0031
License: http://creativecommons.org/licenses/by/4.0/
Importance score: 83/100
The gist: Performance of the AstroPix Prototype Module for the Barrel Imaging Calorimeter at the ePIC Detector and in Space-Based Payloads is a study validating various AstroPix v3 configurations to…
Key concepts
- AstroPix Sensor Characteristics
- AstroPix is a high-voltage CMOS sensor designed for precision gamma-ray imaging and spectroscopy in the medium energy range (100 keV to 100 MeV). It features a small 500 µm pixel pitch, built-in amplification, and low power consumption, making it suitable for large telescope detector planes.
- Prototype Configurations Tested
- The research tested different physical arrangements of AstroPix chips: a single chip (2x2 cm), a quad-chip assembly (4x4 cm), and a nine-chip linear array (1x9 cm). These configurations were evaluated to see which best demonstrated operational reliability and scalability for detector planes.
- Performance Validation Metrics
- The tests assessed several key performance aspects, including noise level, pixel uniformity, chip variation, and rate capability. These were measured using injection tests to check pixel response consistency and cosmic-ray/source tests to evaluate overall stability under simulated operational conditions.
Terminology
Summary
Performance of the AstroPix Prototype Module for the Barrel Imaging Calorimeter at the ePIC Detector and in Space-Based Payloads is a study validating various AstroPix v3 configurations to demonstrate their operational feasibility for both space-based payloads and future collider detectors like the EIC. p. 0 With these features, AstroPix meets the requirements of future space-based high-energy telescopes
and the imaging layers of the Barrel Imaging Calorimeter (BIC) in the Electron-Proton/Ion Collider
(ePIC) detector at the future Electron-Ion Collider (EIC). For the space-based payload, AstroPix is
being integrated into sounding rocket and balloon payloads to demonstrate the technical readiness
of the devices.Where the paper says it
AstroPix Sensor Characteristics
AstroPix is a high-voltage CMOS (HV-CMOS) monolithic active pixel sensor originally developed to enable precision gamma-ray imaging and spectroscopy in the medium-energy regime (∼100 keV–100 MeV) based on the groundwork laid by ATLASpix and MuPix It features a 500 µm pixel pitch, in-pixel amplification and digitization, and low power consumption (∼3-4 mW/cm2), making it scalable for large-area, multilayer telescope detector planes The detectors have a designed dynamic range of 25 keV to 700 keV
Prototype Configurations Tested
The study tested various AstroPix v3 configurations, including the single chip, a quad-chip assembly, a three-layer stack of quad chips, and a 9-chip module that represents the smallest prototype unit of the BIC imaging layer The single chip has ∼2 cm × 2 cm; the quad-chip is a 2 × 2 array of single chips (sensor size ∼4 cm × 4 cm); and the nine-chip module is a 1 × 9 linear array of single chips The nine-chip module was tested with a tighter noise-rate cut of 1 Hz, compared to 2 Hz for the quad-chip module
Performance Validation Metrics
The main goal of the tests with various AstroPix v3 configurations is to validate their operation—including basic device functionality such as DAQ communication and daisy-chain readout—as well as performance aspects such as noise level, chip uniformity, pixel-to-pixel variation, and rate capability evaluated through injection tests, cosmic-ray tests, and source tests For data acquisition, the A-STEP hardware (A-STEP HW) developed as a sounding rocket payload was used for the current performance evaluation The injection test was performed to evaluate pixel-to-pixel response uniformity and variation using the same injection voltage per pixel, based on the hit and ToT maps
Key Results from Module Testing
The quad-chip achieved reliable readout and a three-layer stack demonstrated synchronized multi-layer operation confirming the scalability of the design The nine-chip prototype also achieved a 99% active-pixel yield with stable performance and satisfied the hit-rate requirements indicating reliable operation under realistic beam conditions The measured performance meets the requirements for both the BIC imaging layers at the EIC and the A-STEP space mission Although the hit-rate test was conducted with the nine-chip prototype, the results confirm sufficient performance for the quad-chip detector planned for A-STEP Future versions are under development to achieve substantially higher hit rates at both the pixel and chip levels, along with full depletion, fast time resolution, and low power consumption
Operational Feasibility Summary
The results demonstrate that the nine-chip prototype module operated as intended with the current setup including daisychained readout The nine-chip module exhibits two distinct ToT response groups, one comprising chip 2, 6, and 7 with a most probable value around 3 µs, and another including chip 0, 1, 3, 4, and 5 with a most probable value around 4 µs The maximum per-chip rate was measured to be about 1.6 kHz The maximum expected hit rate per chip for the imaging layers in the EIC environment is about 925 Hz, taking into account DIS, electron, and proton beam backgrounds The nine-chip prototype module satisfies the requirements for both the BIC imaging layers and A-STEP
Final Conclusion on Design
The AstroPix v3 design proves feasible for both collider and space-based detector applications while the current design is limited to a maximum hit rate of approximately 4 Hz per pixel The paper concludes that the AstroPix v3 design proves feasible for both collider and space-based detector applications while the current design is limited to a maximum hit rate of approximately 4 Hz per pixel The paper concludes that the AstroPix v3 design proves feasible for both collider and space-based detector applications while the current design is limited to a maximum hit rate of approximately 4 Hz per pixel
References
[1] R. Caputo, et al. p. 0 Performance of the AstroPix Prototype Module for the
Barrel Imaging Calorimeter at the ePIC Detector and in
Space-Based Payloads
Bobae Kim,𝑎,∗ Regina Caputo,𝑏 Manoj Jadhav,𝑎 Sylvester Joosten,𝑎 Adrien
Laviron,𝑏 Richard Leys,𝑐 Jessica Metcalfe,𝑎 Nicolas Striebig,𝑐 Daniel Violette𝑏
and Maria Żurek𝑎
𝑎Argonne National Laboratory
9700 S Cass Ave, Lemont, 60439, IL, USA
𝑏NASA Goddard Space Flight Center
8800 Greenbelt Rd, Greenbelt, 20771, MD, USA
𝑐Karlsruhe Institute of Technology
Hermann-von-Helmholtz-Platz 1, Karlsruhe, D-76344, Baden-Württemberg, Germany
E-mail: bobae. gov
AstroPix is a high-voltage CMOS (HV-CMOS) monolithic active pixel sensor originally developed to enable precision gamma-ray imaging and spectroscopy in the medium-energy regime
(∼100 keV–100 MeV) based on the groundwork laid by ATLASpix and MuPix. Performance of the AstroPix Prototype Module for the
Barrel Imaging Calorimeter at the ePIC Detector and in
Space-Based Payloads
Bobae Kim,𝑎,∗ Regina Caputo,𝑏 Manoj Jadhav,𝑎 Sylvester Joosten,𝑎 Adrien
Laviron,𝑏 Richard Leys,𝑐 Jessica Metcalfe,𝑎 Nicolas Striebig,𝑐 Daniel Violette𝑏
and Maria Żurek𝑎
𝑎Argonne National Laboratory
9700 S Cass Ave, Lemont, 60439, IL, USA
𝑏NASA Goddard Space Flight Center
8800 Greenbelt Rd, Greenbelt, 20771, MD, USA
𝑐Karlsruhe Institute of Technology
Hermann-von-Helmholtz-Platz 1, Karlsruhe, D-76344, Baden-Württemberg, Germany
E-mail: bobae. gov
AstroPix is a high-voltage CMOS (HV-CMOS) monolithic active pixel sensor originally developed to enable precision gamma-ray imaging and spectroscopy in the medium-energy regime
(∼100 keV–100 MeV) based on the groundwork laid by ATLASpix and MuPix. Performance of the AstroPix Prototype Module for the Barrel Imaging Calorimeter at the ePIC Detector and
in Space-Based Payloads Bobae Kim
1. Introduction
A novel High-Voltage CMOS (HV-CMOS) monolithic active pixel sensor named AstroPix
has been developed for the proposed All-sky Medium-Energy Gamma-ray Observatory eXplorer
(AMEGO-X) mission concept, a medium-energy (100 keV–100 MeV) gamma-ray telescope designed to deepen our understanding of astrophysical phenomena by identifying and characterizing gamma-rays from explosions and high-energy particle acceleration in the universe [1].Where the paper says it
Where the paper says it
Where the paper says it
[2] R. Caputo, et al., “ComPair-2: a next-generation medium-energy gamma-ray telescope prototype,” Proc. p. 7 Caputo, et al. , “ComPair-2: a next-generation medium-energy gamma-ray telescope prototype,” Proc. , “ComPair-2: a next-generation medium-energy gamma-ray telescope prototype,” Proc. 13093 (2024), 130932L doi:10.Where the paper says it
Where the paper says it
[3] D. P. Violette, et al. p. 7 02562 [astro-ph. Violette, et al. Violette, et al. , “A-STEP: the AstroPix sounding rocket technology demonstration
payload,” Proc.Where the paper says it
Where the paper says it
[4] R. Abdul Khalek, et al. p. 7 13093, *Space Telescopes and Instrumentation 2024: Ultraviolet
to Gamma Ray*, 1309381, Aug. Abdul Khalek, et al. Abdul Khalek, et al. , “Science Requirements and Detector Concepts for the ElectronIon Collider: EIC Yellow Report,” Nucl.Where the paper says it
Where the paper says it
[5] H. Klest, et al. p. 7 1026, 122447, 2022. Klest, et al. Klest, et al. , “Evaluation of the response to electrons and pions in the scintillating fiber
and lead calorimeter for the future electron-ion collider,” Journal of Instrumentation, vol.Where the paper says it
Where the paper says it
[6] A. L. Steinhebel, et al. p. 7 1088/1748-0221/20/07/P07028. Steinhebel, et al. 1088/1748-0221/20/07/P07028. Steinhebel, et al. Steinhebel, et al. , “AstroPix: novel monolithic active pixel silicon sensors for future
gamma-ray telescopes,” Proc.Where the paper says it
Where the paper says it
Where the paper says it
[7] Y. Suda, et al. p. 7 12181, *Space Telescopes and Instrumentation 2022:
Ultraviolet to Gamma Ray*, 121816Y, Aug. Suda, et al. 12181, *Space Telescopes and Instrumentation 2022:
Ultraviolet to Gamma Ray*, 121816Y, Aug. Suda, et al. Suda, et al. , “Performance evaluation of the high-voltage CMOS active pixel sensor AstroPix
for gamma-ray space telescopes,” Nucl. , “Performance evaluation of the high-voltage CMOS active pixel sensor AstroPix
for gamma-ray space telescopes,” Nucl. Methods Phys. , “Performance evaluation of the high-voltage CMOS active pixel sensor AstroPix
for gamma-ray space telescopes,” Nucl. Methods Phys. , “Performance evaluation of the high-voltage CMOS active pixel sensor AstroPix
for gamma-ray space telescopes,” Nucl. Methods Phys.Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
[8] A. L. Steinhebel, et al., “AstroPix: A Pixelated HVCMOS Sensor for Space-Based GammaRay Measurement,” Nucl. p. 7 Steinhebel, et al. , “AstroPix: A Pixelated HVCMOS Sensor for Space-Based GammaRay Measurement,” Nucl.Where the paper says it
[9] N. Striebig, et al. p. 0 Performance of the AstroPix Prototype Module for the
Barrel Imaging Calorimeter at the ePIC Detector and in
Space-Based Payloads
Bobae Kim,𝑎,∗ Regina Caputo,𝑏 Manoj Jadhav,𝑎 Sylvester Joosten,𝑎 Adrien
Laviron,𝑏 Richard Leys,𝑐 Jessica Metcalfe,𝑎 Nicolas Striebig,𝑐 Daniel Violette𝑏
and Maria Żurek𝑎
𝑎Argonne National Laboratory
9700 S Cass Ave, Lemont, 60439, IL, USA
𝑏NASA Goddard Space Flight Center
8800 Greenbelt Rd, Greenbelt, 20771, MD, USA
𝑐Karlsruhe Institute of Technology
Hermann-von-Helmholtz-Platz 1, Karlsruhe, D-76344, Baden-Württemberg, Germany
E-mail: bobae. gov
AstroPix is a high-voltage CMOS (HV-CMOS) monolithic active pixel sensor originally developed to enable precision gamma-ray imaging and spectroscopy in the medium-energy regime
(∼100 keV–100 MeV) based on the groundwork laid by ATLASpix and MuPix. Striebig, et al. , “AstroPix4 — a novel HV-CMOS sensor developed for space based experiments,” Journal of Instrumentation, vol.Where the paper says it
Where the paper says it
[10] Y. Suda, et al., “Evaluation of gamma-ray response of the AstroPix4 HV-CMOS active pixel sensor,” Nucl. p. 7 Suda, et al. , “Evaluation of gamma-ray response of the AstroPix4 HV-CMOS active pixel sensor,” Nucl.Where the paper says it
Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.
Improvements for AI systems
-
Automated performance validation of AstroPix configurations can be improved by implementing continuous testing protocols that evaluate
noise level, chip uniformity, pixel-to-pixel variation, and rate capability
through injection tests, cosmic-ray tests, and source tests. This allows the AI system to autonomously select the optimal AstroPix v3 configuration for a given mission requirement. -
Enhanced system modeling can be achieved by integrating the measured
ToA
andToT
distributions into predictive models for shower profile reconstruction in Lead/Scintillating Fiber (Pb/SciFi) sampling calorimeters. This capability allows the AI to performprecise energy and shower profile measurements
that enable key performance features likeelectron/pion or gamma/neutral pion separation.
-
The system can be upgraded to incorporate real-time hit rate monitoring based on the results from the nine-chip prototype module, which demonstrated a maximum per-chip rate of about 1.6 kHz. This allows the AI to dynamically adjust data acquisition parameters to ensure operation within
realistic beam conditions
orspace-mission conditions.
Abstract
AstroPix is a high-voltage CMOS (HV-CMOS) monolithic active pixel sensor originally developed to enable precision gamma-ray imaging and spectroscopy in the medium-energy regime (approximately 100 keV-100 MeV) based on the groundwork laid by ATLASpix and MuPix. It features a 500 um pixel pitch, in-pixel amplification and digitization, and low power consumption (around 3-4 mW/cm 2), making it scalable for large-area, multilayer telescope detector planes. The detectors have a designed dynamic range of 25 keV to 700 keV. With these features, AstroPix meets the requirements of future space-based high-energy telescopes and the imaging layers of the Barrel Imaging Calorimeter (BIC) in the Electron-Proton/Ion Collider (ePIC) detector at the future Electron-Ion Collider (EIC). For the space-based payload, AstroPix is being integrated into sounding rocket and balloon payloads to demonstrate the technical readiness of the devices. For BIC, AstroPix-based imaging layers interleaved within the lead/scintillating-fiber (Pb/SciFi) sampling calorimeter provide granular shower imaging, enabling key performance features such as electron/pion or gamma/neutral-pion separation. As part of the ongoing detector R&D efforts, we have been testing various AstroPix v3 configurations: the single chip, a quad-chip assembly, a three-layer stack of quad chips, and a nine-chip module that represents the smallest prototype unit of the BIC imaging layer. This presentation will highlight recent performance test results from these AstroPix detector configurations.
Sources
Related papers
- On-sky demonstration of a vector Zernike wavefront sensor in a cascaded adaptive optics system
- Euclid Data Release 1 (DR1): Calibration strategy and observations
- The General Antiparticle Spectrometer (GAPS) Antarctic Balloon Payload
- Detection and excision of radio-frequency interference in radio arrays
- Unified matched-filter and excess-power pipeline for gravitational-wave detector characterization
- Ushering in sub-arcsecond angular resolution observatories in the far-infrared: The case for a double-Fourier interferometer