Effect of Mangosteen Peel (Garcinia mangostana L.) and Grass Jelly Leaf (Cyclea barbata L. Miers) Natural Dye Mixing Ratio on the Optical, Morphological, and Photovoltaic Properties of Dye-Sensitized Solar Cells (DSSC)
Listen
Radio episode about this paper
Transcript
Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.
Kai: We're looking at the paper: "Effect of Mangosteen Peel (Garcinia mangostana L.) and Grass Jelly Leaf (Cyclea barbata L. Miers) Natural Dye Mixing Ratio on the Optical, Morphological, and Photovoltaic Properties of Dye-Sensitized Solar Cells (DSSC)".
Mira: Here's the gist of the paper. Dye-sensitized solar cells (DSSCs) are promising low-cost and environmentally friendly photovoltaic devices, especially when utilizing natural sensitizers.
Kai: This study explores the effect of concentration ratios of natural dyes extracted from mangosteen peel (MP) and grass jelly leaves (GJL) on the optical, morphological, and photovoltaic properties of DSSCs.
Mira: The composite dye with a 1:3 (MP:GJL) ratio yielded the highest PCE of 3.50%, demonstrating the synergistic effect of combining these natural sensitizers to broaden the light absorption spectrum.
Kai: Synergistic Optical Properties The UV-Vis absorption spectra showed that MP contributes to the UV-blue region (350-450), while GJL contributes to the red region (650-700 nm).
Title and authors: Kai: So we're looking at this paper right now, "Effect of Mangosteen Peel (Garcinia mangostana L.) and Grass Jelly Leaf (Cyclea barbata L. Miers) Natural Dye Mixing Ratio on the Optical, Morphological, and Photovoltaic Properties of Dye-Sensitized Solar Cells (DSSC)." It's about using natural dyes from mangosteen peel and grass jelly leaves to make these low-cost solar cells.
Mira: Yeah, it’s interesting because it looks at how mixing those two different sources affects everything: the light they absorb, how the film physically looks, and ultimately, how well they convert sunlight into electricity. We're talking about a real look at using natural materials instead of expensive synthetic dyes three <ref:2509.26622#pg1>.
Lev: I’m curious about what you mean by "everything," Mira. When you say optical properties and morphology, are we talking about the light absorption spectrum and the physical structure of the film, right? Because for us in hardware, those details matter a lot for how efficiently electrons get in and out.
Kai: Exactly. The paper looks at how different ratios of these two dyes change which colors of light they absorb best. It shows that mangosteen peel is good for the UV-blue part, like three hundred fifty to four hundred fifty nanometers, and grass jelly leaves handle the red region around six hundred fifty to seven hundred nanometers <ref:2509.26622#pg2>.
Mira: And the key finding there is that mixing them doesn't cause any major chemical changes between the dyes themselves. They just add up their absorption strengths, which is what makes this composite dye work better than either one alone two <ref:2509.26622#pg1>.
Lev: That's a relief for stability, because if they were reacting chemically, we’d have to worry about some nasty degradation during the cell fabrication process. But what about the actual performance numbers? What were the baseline efficiencies they got from just using mangosteen peel and just using grass jelly leaves individually?
Kai: The paper states that when you use just the mangosteen peel dye, you get a power conversion efficiency of two point seven five percent, and if you only use the grass jelly leaf dye, it's two point one two percent two <ref:2509.26622#pg1>. That gives us a baseline to compare against.
Mira: And then they test various volume ratios of the mix: they test three to one, two to one, one to one, two to one again at a different ratio, and finally three to one again for the best results two <ref:2509.26622#pg1>.
Lev: So what’s the headline number for this entire study? What is the best power conversion efficiency they actually achieved in this setup?
Title and authors: Kai: The composite dye with a three to one ratio of mangosteen peel to grass jelly leaf yielded the highest power conversion efficiency at three point five zero percent two <ref:2509.26622#pg2,The composite dye with a>. That's significantly higher than either natural dye alone, which is what they were comparing against.
Mira: That three point five zero percent number is really tied to that synergistic effect where you broaden the light absorption spectrum across both UV-blue and red regions two <ref:2509.26622#pg2,broaden the light absorption spectrum>. It’s not just additive performance; it’s something better because of the combination.
Lev: From an engineering standpoint, what does that improved light absorption mean for the actual device structure? Does it suggest something about how well these hybrid dyes stick to the titanium dioxide layer?
Kai: The paper points out that at the three to one ratio, you see a very uniform and homogenous nanoporous structure in the mixed-dye sample two <ref:2509.26622#pg1>. They found this suggests enhanced interfacial compatibility between these hybrid natural dyes and the titanium dioxide layer.
Mira: I agree. That better physical structure is what we want because it means better charge injection into the conduction band and less chance for charge recombination losses, which is a big issue in these devices two <ref:2509.26622#pg1>. It implies the optimized morphology at that ratio helps lower those losses.
Lev: But then there’s this part about stability, right? The cycling data shows that things change over time. What’s the trade-off they found between having high initial performance and keeping it stable over many cycles?
Kai: They observed a clear trade-off depending on the dye composition. Samples with a grass jelly leaf rich composition, specifically one to three and one to two ratios of mangosteen peel to grass jelly leaf, started with the highest efficiencies and kept more of that initial performance across several cycles six <ref:2509.26622#pg1>.
Mira: That’s interesting because it means the structure they got at those specific ratios is inherently more stable photochemically than the balanced one six <ref:2509.26622#pg1>. They found that the one to one mixture showed a very rapid collapse in power conversion efficiency after only a few cycles six <ref:2509.26622#pg1>.
Lev: Rapid collapse sounds bad for practical applications. It suggests that whatever mechanism is causing that failure in the one to one mix, it’s pretty sensitive. Are we talking about photobleaching or something else?
Title and authors: Kai: The mechanistic interpretation points toward a couple of things: photobleaching and molecular degradation, which reduces light absorption over time six <ref:2509.26622#pg1>. Plus, dye desorption from the titanium dioxide surface is another factor where weaker binding lets the dyes wash away into the electrolyte and causes a rapid loss of active dye coverage six <ref:2509.26622#pg1>.
Mira: So it’s not just one failure mode; it’s a combination of things happening at once. The authors suggest that optimizing a natural-dye DSSC requires balancing that initial high performance with long-term photochemical and interfacial stability six <ref:2509.26622#pg1>. It shows you can't just pick the best number on paper and assume it lasts.
Lev: That makes sense for real hardware. We’re building things to run reliably, not just hit a peak efficiency in a lab measurement. So, what is the big picture implication of finding this three point five zero percent PCE using natural dyes <ref:2509.26622#pg2>?
Kai: The main thing is that it shows the potential of these natural dye combinations as low-cost and environmentally friendly sensitizers for solar energy applications two <ref:2509.26622#pg1>. It proves that you can get performance comparable to some synthetic methods, but with materials that are much cheaper and less harmful.
Mira: And the synergy—broadening the absorption across complementary regions—is key. It suggests we should really focus on finding these natural dye pairs that complement each other well for future solar cell design two <ref:2509.26622#pg1>.
Lev: For me, it means that if we want to make real hardware using these dyes, we need to focus our effort not just on the highest initial efficiency, but on the ones that show better retention in cycling tests six <ref:2509.26622#pg1>. That’s where the real engineering work is needed.
Kai: So, to wrap up this paper on "Effect of Mangosteen Peel (Garcinia mangostana L.) and Grass Jelly Leaf (Cyclea barbata L. Miers) Natural Dye Mixing Ratio on the Optical, Morphological, and Photovoltaic Properties of Dye-Sensitized Solar Cells (DSSC)," we see that a three to one ratio gives three point five zero percent PCE two <ref:2509.26622#pg2,on the Optical, Morphological, and Photovoltaic Properties of>.
Mira: And we see that the key is balancing spectral coverage and initial efficiency with long-term stability, especially looking at those GJL-rich compositions which retain performance better over cycles six <ref:2509.26622#pg1>.
Lev: And from an engineering standpoint, it confirms that optimizing a natural-dye DSSC requires balancing spectral coverage and initial PCE with long-term photochemical and interfacial stability six <ref:2509.26622#pg1>. That’s what matters when you move from the lab to the real world.
The paper's summary: Kai: So we just talked about how mixing mangosteen peel and grass jelly leaf dyes can actually make a dye-sensitized solar cell perform better than either one alone, hitting a power conversion efficiency of three point five zero percent when you use that three to one ratio two.
Mira: Right. And the real story here is not just that it's more efficient, but why the way they blend those two different natural sources works so well optically. It’s about how they cover the light spectrum better than if you just used one dye.
Lev: From an error correction standpoint, if we think about this like a system with noisy channels, combining two different types of noise sources—the UV blue from the mangosteen and the red from the grass jelly—to cover a wider band is analogous to having more diverse inputs for your measurement.
Kai: Exactly. The paper shows that mangosteen peel handles those shorter wavelengths, say three hundred fifty to four hundred fifty nanometers, while grass jelly leaves handle those longer wavelengths, around six fifty to seven hundred nanometers two.
Mira: And the crucial assumption they make is that these two natural extracts don't have any weird chemical interactions when mixed. They just add up their absorption strengths without messing up each other’s fundamental way of absorbing light. That's a big part of why this approach is appealing for using natural materials two.
Lev: That assumption is key for us because if there was a reaction, we’d have to model the kinetics of that reaction, which adds complexity and uncertainty to the whole device modeling process.
Kai: The resulting composite dye then broadens the overall light-harvesting window across more of the visible spectrum. It moves it from being just one color specialist to being more panchromatic, which is what we want for a solar absorber two.
Mira: And that optical broadening leads directly into what they call morphological optimization. They look at how the physical film looks under different ratios, and they found that the balanced mixtures—like one to one and three to one—show a very uniform structure with no cracks six.
Lev: That uniformity is what we need for charge transfer. If you have a cracked film or patchy dye coverage, you get poor electron injection and high recombination losses, which would destroy your open circuit voltage two.
Kai: So the paper concludes that the three to one ratio gives the best initial power conversion efficiency of three point five zero percent because it optimizes both light absorption and charge collection simultaneously two.
Mira: But then they introduce a stability curve. They show that while high ratios give you great initial performance, they also look at how fast things break down over ten cycles six. They found that the grass jelly leaf rich compositions have better long-term retention than the perfectly balanced one to one mixture six.
Lev: That means we can’t just optimize for peak performance and forget about durability. We have to model the degradation mechanisms, like photobleaching or dye desorption from the titanium dioxide surface, because that's what causes those cycles to drop off rapidly in some configurations six.
Kai: So, the paper is showing that blending natural dyes is a promising route for low-cost cells, but we still have to figure out how to make them last. That sets up the next part of our discussion on stability modeling.
The paper's improvements: Kai: So we just covered how mixing those two natural dyes gives you a three point five zero percent efficiency at that three to one ratio two. And now we're looking at what the authors suggest they should actually *do* with this information for real-world hardware.
Mira: They aren't just stopping there with the numbers; they are proposing a way to predict exactly which ratio will give you the best power conversion efficiency, which is something we can use to guide material formulation in a lab two.
Lev: That makes sense because right now, trying every single ratio by hand is too time-consuming when you're building real hardware. Predicting the optimal combination based on the input ratios lets us skip a lot of trial and error for us, right?
Kai: They also suggest creating a system that can predict the morphological outcomes. If we know which ratio gives you that uniform nanoporous structure we talked about, we can design the synthesis process to aim for that specific physical shape instead of just hoping it happens by accident two.
Mira: That prediction needs to be based on the assumption that those structural improvements at one to one and three to one ratios correlate directly with better charge injection and less recombination losses into the electrolyte two.
Lev: We need a stability assessment module too, something that models photobleaching and molecular degradation over time during cycling, like what they saw in Figure six six. That’s how we move from a high initial efficiency measurement to knowing if it will actually run for months on a solar panel two.
Kai: So the implied improvement is moving away from just optimizing for peak power conversion efficiency and instead balancing that spectral coverage and initial performance with long-term photochemical and interfacial stability two.
Mira: That's the big conceptual shift they're pointing toward. It tells us that in natural dye systems, you can’t just pick the highest number on paper; you have to find the compositional window that maximizes both properties simultaneously two.
Lev: For our hardware work, this means our next step should be developing a predictive model for those MP to GJL ratios so we can design robust cells from the start instead of just testing a few fixed mixes two.
Kai: Exactly. It shows that using natural dye combinations is viable, but it requires us to treat the material formulation as an optimization problem balancing absorption and longevity two.
Conclusion: Kai: So we’re wrapping up on this paper about "Effect of Mangosteen Peel (Garcinia mangostana L.) and Grass Jelly Leaf (Cyclea barbata L. Miers) Natural Dye Mixing Ratio on the Optical, Morphological, and Photovoltaic Properties of Dye-Sensitized Solar Cells (DSSC)" by summarizing everything we just talked about.
Mira: Basically, the main point is that mixing those two natural dyes works synergistically to broaden the light absorption spectrum, leading to a higher power conversion efficiency of three point five zero percent at that three to one ratio.
Lev: It’s interesting how they found that while high ratios give you good initial performance, the stability drops quickly in some configurations because of things like dye desorption from the titanium dioxide surface six.
Kai: And the authors suggest that optimizing a natural-dye DSSC requires balancing that initial high performance with long-term photochemical and interfacial stability two.
Mira: That suggests we can't just chase the highest PCE number, but we have to look at how the material behaves over ten cycles six, especially those GJL rich compositions which showed better retention than the balanced one two.
Lev: I just want to say that for our error correction work, seeing that trade-off between instantaneous performance and operational stability is a really good lesson for designing any real hardware two.
Kai: It proves that using natural dye combinations is a viable path for low-cost cells, but we still have to figure out how to make them last through real use two.
Mira: And the synergy in light harvesting across those UV-blue and red regions really opens up ideas for designing future solar absorbers two.
Lev: We’re going to need models that predict that stability better than what they showed here, which is where the next set of studies on degradation mechanisms comes in.
Eka Nurfani, Haifa Salsabila, Dwiky I. Bakhtiar, Wahyu S. Sipahutar, M Alvien Ghifari, Rishal Asri, Meqorry Yusfi, Tarmizi Taher, Aditya Rianjanu, Robi Kurniawan
Department of Materials Engineering, Institut Teknologi Sumatera, South Lampung 35365, Indonesia · Department of Chemistry, Faculty of Sciences, Institut Teknologi Sumatera, South Lampung 35365, Indonesia · Department of Energy System Engineering, Faculty of Industrial Technology, Institut Teknologi Sumatera, South Lampung 35365 · Department of Physics, Faculty of Mathematics and Natural Sciences, Universitas Andalas · Department of Environmental Engineering, Faculty of Infrastructure and Regional Technology, Institut Teknologi Sumatera, South Lampung 35365 · Center for Green and Sustainable Materials, Institut Teknologi Sumatera
cond-mat.mtrl-sci
Submitted: 2025-09-30
Updated: 2026-11-14
Comments: v2: revised version (title and abstract revised). Power conversion efficiencies are now reported as apparent (relative) values, because the input power was estimated photometrically rather than with a calibrated AM1.5G source. 29 pages, 8 figures, 1 table
License: http://arxiv.org/licenses/nonexclusive-distrib/1.0/
Importance score: 72/100
The gist: Dye-sensitized solar cells (DSSCs) are promising low-cost and environmentally friendly photovoltaic devices, especially when utilizing natural sensitizers.
Key concepts
- Dye-Sensitized Solar Cells (DSSCs)
- These are low-cost solar cells that use natural dyes to capture sunlight. The dye absorbs light energy and injects electrons into a semiconductor material (like TiO2), which then generate electricity when an external circuit is connected.
- Synergistic Effect
- This occurs when combining two different substances creates a result greater than the sum of their individual effects. In this study, mixing MP and GJL dyes broadened the light spectrum they could absorb, leading to a higher overall efficiency (PCE) in the solar cell.
- Photovoltaic Performance Metrics
- These are measurements used to evaluate how well a solar cell works. Key metrics include Power Conversion Efficiency (PCE), which measures how much sunlight is converted into electricity, and current density ($J_{sc}$), which reflects the number of electrons collected from the absorbed light.
Terminology
Summary
Dye-sensitized solar cells (DSSCs) are promising low-cost and environmentally friendly photovoltaic devices, especially when utilizing natural sensitizers. p. 1 This study explores the effect of concentration ratios of natural dyes extracted from mangosteen peel (MP) and grass jelly leaves (GJL) on the optical, morphological, and photovoltaic properties of DSSCs. p. 1 The composite dye with a 1:3 (MP:GJL) ratio yielded the highest PCE of 3. p. 1 p. 1 p. 150%, demonstrating the synergistic effect of combining these natural sensitizers to broaden the light absorption spectrum. p. 1 p. 1 p. 1
Synergistic Optical Properties
The UV-Vis absorption spectra showed that MP contributes to the UV-blue region (350-450), while GJL contributes to the red region (650-700 nm). The mixing process successfully combines the optical properties of both extracts without significant chemical interaction that would alter their fundamental absorption characteristics. p. 8 As the volume ratio of GJL to MP increases (from 3:1 to 1:3), a clear trend is observed where the intensity of the chlorophyll-related peak in the red region increases progressively, while the intensity of the anthocyanin peak in the blue region decreases accordingly. p. 8 This blending strategy effectively broadens the overall light-harvesting window across the visible spectrum, creating a more panchromatic sensitizer. p. 9
Morphological Optimization
Significant morphological variations were observed across the different ratios of MP to GJL natural dyes. The MP-rich compositions (3:1 and 2:1) exhibit pronounced cracking and poor film continuity, characteristic of excessive interfacial stress during drying. In contrast, the balanced 1:1 ratio shows a homogeneous, crack-free morphology with uniform dye coverage, indicating favourable interfacial compatibility and suggesting efficient charge transfer with minimal recombination losses. The mixed-dye sample demonstrates a uniform and homogenous nanoporous structure, suggesting enhanced interfacial compatibility between the hybrid natural dyes and the TiO2 layer. p. 8
Photovoltaic Performance Metrics
The power conversion efficiency (PCE) of MP and GJL dyes is 2.75% and 2.12%, respectively. The composite dye with a 1:3 (MP:GJL) ratio yielded the highest PCE of 3.50%, demonstrating the synergistic effect of combining these natural sensitizers to broaden the light absorption spectrum. This enhancement suggests a synergistic effect between the two natural dyes, where the complementary light absorption spectra and improved dye loading may contribute to enhanced charge generation and collection. p. 1
Cycling Stability Analysis
Two essential and experimentally relevant observations emerge from the data regarding cycling. Samples with a GJL-rich composition (1:3 and 1:2 MP:GJL) begin with the highest efficiencies and retain a larger fraction of their initial performance across cycles, whereas the 1:1 mixture exhibits a very rapid collapse in PCE after only a few cycles. This indicates a clear trade-off between instantaneous performance and operational stability that depends intensely on dye composition. p. 8
Conclusion
This study demonstrates that blending natural dyes from mangosteen peel (MP) and grass jelly leaves (GJL) significantly enhances the performance of dye-sensitized solar cells (DSSCs). The 1:3 (MP:GJL) ratio achieved the highest power conversion efficiency of 3. p. 9 p. 950%, outperforming either dye alone (MP: 2. p. 0 p. 075%, GJL: 2. p. 1 p. 112%). This improvement is attributed to the synergistic effect that broadens light absorption across complementary UV-blue and red spectra. p. 9 p. 9 These findings highlight the great potential of natural dye combinations as low-cost, environmentally friendly sensitizers for solar energy applications. p. 1 Future work should focus on improving the long-term stability of these bio-sensitized solar cells. p. 0
REFERENCE
B
Pruning redundant reasoning tokens
The abstract states that dye solutions were prepared at a fixed concentration of 0.6 g/mL, with the MP:GJL volume ratio varied at 3:1, 2:1, 1:1, 1:2, and 1:3. p. 1 The currentvoltage (J-V) analysis showed that the power conversion efficiency (PCE) of MP and GJL dyes is 2. p. 175% and 2.12%. The composite dye with a 1:3 (MP:GJL) ratio yielded the highest PCE of 3.50%, demonstrating the synergistic effect of combining these natural sensitizers to broaden the light absorption spectrum.
How the training signal is built
The UV-Vis absorption spectra showed that MP contributes to the UV-blue region (350-450), while GJL contributes to the red region (650-700 nm). The pure MP dye (3:0) shows the strongest absorption related to anthocyanin and -mangostin compared to GJL. p. 8 Conversely, the spectrum for the pure GJL dye (0:3) displays a prominent absorption peak related to chlorophyll. p. 8 The spectra of the blended dyes consistently show two distinct absorption features corresponding to both parental dyes. p. 8
Where the gains come from
The optimal morphological integrity observed at the 1:1, 1:2, and 1:3 MP:GJL ratios implies a synergistic interaction between the two dye types, which is expected to correlate with enhanced photovoltaic performance in corresponding DSSC devices. The mixed-dye photoanode demonstrates a uniform and homogenous nanoporous structure, suggesting enhanced interfacial compatibility between the hybrid natural dyes and the TiO2 layer. p. 8 This optimized morphology is anticipated to facilitate efficient charge injection and reduce recombination, thereby contributing to improved photovoltaic performance in the corresponding DSSCs. p. 9 The higher efficiency observed at the 1:3 MP:GJL ratio can be attributed to enhanced Jsc and stable Voc, suggesting that the synergistic dye interaction improves both photon absorption and charge collection, while also mitigating recombination losses. p. 9 The balanced ratio likely promotes better dye adsorption onto the TiO2 surface, leading to higher dye loading and more efficient electron injection into the conduction band. p. 8
The I-V characteristics also provide insight into the working principles of the DSSCs, since several photovoltaic parameters can be extracted from these curves. The overall power conversion efficiency (PCE) is determined by the interplay of Jsc, Voc, and FF (see Table 1). p. 1 The variation in photocurrent density directly influences the overall photovoltaic performance, which is summarized in Figure 5b. p. 9
The short-circuit current density (Jsc) reflects the number of photogenerated electrons injected from the excited dye molecules into the TiO2 conduction band. The open-circuit voltage (Voc) correspond to the potential difference between the quasi-Fermi level of electrons in TiO2 and the redox potential of the electrolyte, which can be influenced by the dye/electrolyte interface and charge recombination dynamics. p. 7 The slope of the I-V curves near Voc is related to series resistance and recombination losses, affecting the fill factor (FF). p. 7
The drop in efficiency at 0:3 (2.12 ± 0.46%) indicates that an excess of GJL may not favor efficient charge transfer, possibly due to the weaker binding affinity of GJL molecules than MP, leading to reduced dye anchoring stability on the TiO2 surface. Overall, these results emphasize that the synergistic combination of MP and GJL dyes, particularly at the 1:3 ratio, enhances light absorption and charge collection efficiency. p. 8 p. 8 This finding demonstrates the importance of optimizing natural dye mixtures to achieve superior DSSC performance compared to single-dye systems. p. 3 p. 3 p. 3
The current–voltage (I-V) characteristics and the corresponding power conversion efficiencies (PCEs) of DSSCs are shown at different volume ratios. The efficiency values range from 2. p. 612% to 3.50%, with the highest PCE obtained at the 1:3 MP:GJL ratio (3. p. 150 ± 0.19%). On the contrary, using single dyes (3:0 or 0:3 ratios) results in comparatively lower efficiencies (2. p. 775 ± 0.31% and 2.12 ± 0.46%, respectively).
The drop in efficiency at 0:3 (2.12 ± 0.46%) indicates that an excess of GJL may not favor efficient charge transfer, possibly due to the weaker binding affinity of GJL molecules than MP, leading to reduced dye anchoring stability on the TiO2 surface. Overall, these results emphasize that the synergistic combination of MP and GJL dyes, particularly at the 1:3 ratio, enhances light absorption and charge collection efficiency. This finding demonstrates the importance of optimizing natural dye mixtures to achieve superior DSSC performance compared to single-dye systems.
The manuscript emphasizes that optimizing a natural-dye DSSC requires balancing spectral coverage and initial PCE with long-term photochemical and interfacial stability. p. 3 The compositional window that maximizes one property may not maximize the other. p. 3 p. 3 The manuscript emphasizes that optimizing a natural-dye DSSC requires balancing spectral coverage and initial PCE with long-term photochemical and interfacial stability.
Figure 6 shows the evolution of power conversion efficiency (PCE) over ten consecutive cycles for DSSCs sensitized with mixed mangosteen peel (MP) and grass-jelly leaves (GJL) dyes at five different volume ratios. Two essential and experimentally relevant observations emerge from the data. p. 5 First, the samples with a GJL-rich composition (1:3 and 1:2 MP:GJL) begin with the highest efficiencies and retain a larger fraction of their initial performance across cycles, whereas the 1:1 mixture exhibits a very rapid collapse in PCE after only a few cycles. Second, MP-dominant samples (3:1 and 2:1) show intermediate behaviour: moderate initial efficiencies and a steady, but less abrupt, decay with cycling. These trends indicate a clear trade-off between instantaneous performance and operational stability that depends intensely on dye composition. p. 6
A mechanistic interpretation that is consistent with the observed trends involves several interrelated processes. These processes include photobleaching and molecular degradation [31], which reduces light absorption and thus photocurrent over repeated illumination. p. 9 Dye desorption from the TiO2 surface [32] is another process, where weaker binding promotes progressive desorption into the electrolyte and rapid loss of active dye coverage. An imbalance between electron injection and dye regeneration will increase recombination losses during cycling [33]. p. 2 These processes explain why some mixtures (e. p. 4g., 1:3) deliver high initial PCE and better retention (suggesting relatively photostable chromophores and/or stronger surface anchoring).
These processes explain why some mixtures (e.g., 1:3) deliver high initial PCE and better retention (suggesting relatively photostable chromophores and/or stronger surface anchoring). In contrast, other mixtures (notably 1:1) are prone to rapid failure. p. 2 This suggests that optimizing a natural-dye DSSC requires balancing spectral coverage and initial PCE with long-term photochemical and interfacial stability. p. 3 The compositional window that maximizes one property may not maximize the other.
The study demonstrates that blending natural dyes from mangosteen peel (MP) and grass jelly leaves (GJL) significantly enhances the performance of dye-sensitized solar cells (DSSCs). The 1:3 (MP:GJL) ratio achieved the highest power conversion efficiency of 3.50%, outperforming either dye alone (MP: 2.75%, GJL: 2.12%). This improvement is attributed to the synergistic effect that broadens light absorption across complementary UV-blue and red spectra.
These findings highlight the great potential of natural dye combinations as low-cost, environmentally friendly sensitizers for solar energy applications. The synergistic combination of MP and GJL dyes, particularly at the 1:3 ratio, enhances light absorption and charge collection efficiency. p. 9 This finding demonstrates the importance of optimizing natural dye mixtures to achieve superior DSSC performance compared to single-dye systems.
The data availability statement states that the datasets generated during and/or analyzed during the current study are available from the corresponding author. The conflict of interest declares that there are no conflicts of interest. All authors contributed to the submitted manuscript. p. 0 EN contributes to conceptualization, methodology design, resources, writing of original drafts, supervision, and funding acquisition. p. 3 HS and DIB contribute to conducting research and visualization. p. 3 WSS contributes to the supervision and review of the original draft. p. 6 MAG and RA contribute to the resources. p. 2 TT and AR contribute to resources and review of original drafts. p. 6 MY and RK contribute to resource and funding acquisition. EN thanks Institut Teknologi Sumatera (Itera) for supporting this research via “Riset Kolaborasi Indonesia (RKI) 2025” scheme with contract no. p. 0 1998by/IT9.2.1/PT.01.03/2025.
The references list includes [1] Muzayanah IFU, Lean HH, Hartono D, Indraswari KD, Partama R. Population density and energy consumption: A study in Indonesian provinces. p. 2 The references list includes [3] Ballif C, Haug F-J, Boccard M, Verlinden PJ, Hahn G. Status and perspectives of crystalline silicon photovoltaics in research and industry. p. 2 The references list includes [4] Chopra KL, Paulson PD, Dutta V. Thin-film solar cells: an overview. p. 2 The references list includes [7] Wu C-G. Ruthenium-based complex dyes for dye-sensitized solar cells. p. 0 The references list includes [8] Yadav S, Tiwari KS, Gupta C, Tiwari MK, Khan A, Sonkar SP. A brief review on natural dyes, pigments: Recent advances and future perspectives. p. 2
Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.
Improvements for AI systems
-
Develop predictive models for DSSC performance based on MP:GJL ratios to identify optimal combinations for maximizing power conversion efficiency, as indicated by
The composite dye with a 1:3 (MP:GJL) ratio yielded the highest PCE of 3.50%.
-
Create a system capable of predicting morphological outcomes, specifically identifying the
optimal morphological integrity observed at the 1:1, 1:2, and 1:3 MP:GJL ratios
to guide material formulation for better charge transfer. -
Implement a stability assessment module that predicts long-term operational lifetime by modeling the
photobleaching and molecular degradation
anddye desorption from the TiO2 surface
processes during cycling, as discussed in Figure 6 analysis.
Related papers
- Structural contribution to light-induced gap suppression in Ta 2 NiSe 5
- Anatomy of fast current-induced skyrmion motion in synthetic antiferromagnets
- Magnetic control of an exciton-polariton condensate in a van der Waals magnet
- High-pressure elastic properties of GeO2 polymorphs up to 120 GPa
- Decoupling Strain-Rate Sensitivity and Deformation Length Scale Effects in Neutron-Irradiated Tungsten: A Coupled Nano-Indentation, HR-EBSD and Crystal Plasticity Study
- Magnetism modulation in Co3Sn2S2 by current-assisted domain wall motion