Effect of Mangosteen Peel (Garcinia mangostana L.) and Grass Jelly Leaf (Cyclea barbata L. Miers) Natural Dye Mixing Ratio on the Optical, Morphological, and Photovoltaic Properties of Dye-Sensitized Solar Cells (DSSC)
summary
The gist
Dye-sensitized solar cells (DSSCs) are promising low-cost and environmentally friendly photovoltaic devices, especially when utilizing natural sensitizers.
In short
This study tested mixing ratios of natural dyes from mangosteen peel (MP) and grass jelly leaves (GJL) in dye-sensitized solar cells (DSSCs). The 1:3 MP:GJL ratio achieved the highest power conversion efficiency of 3.50%, showing a synergistic effect that broadens light absorption across UV-blue and red spectra. Morphological analysis revealed that the 1:1, 1:2, and 1:3 ratios offered optimal film integrity.
Key concepts
- Dye-Sensitized Solar Cells (DSSCs)
- These are low-cost solar cells that use natural dyes to capture sunlight. The dye absorbs light energy and injects electrons into a semiconductor material (like TiO2), which then generate electricity when an external circuit is connected.
- Synergistic Effect
- This occurs when combining two different substances creates a result greater than the sum of their individual effects. In this study, mixing MP and GJL dyes broadened the light spectrum they could absorb, leading to a higher overall efficiency (PCE) in the solar cell.
- Photovoltaic Performance Metrics
- These are measurements used to evaluate how well a solar cell works. Key metrics include Power Conversion Efficiency (PCE), which measures how much sunlight is converted into electricity, and current density ($J_{sc}$), which reflects the number of electrons collected from the absorbed light.
Terminology used across episodes
This episode discusses
- Effect of Mangosteen Peel (Garcinia mangostana L.) and Grass Jelly Leaf (Cyclea barbata L. Miers) Natural Dye Mixing Ratio on the Optical, Morphological, and Photovoltaic Properties of Dye-Sensitized Solar Cells (DSSC) · Paper Radio
The paper
Effect of Mangosteen Peel (Garcinia mangostana L.) and Grass Jelly Leaf (Cyclea barbata L. Miers) Natural Dye Mixing Ratio on the Optical, Morphological, and Photovoltaic Properties of Dye-Sensitized Solar Cells (DSSC) · Read on arXiv
Eka Nurfani, Haifa Salsabila, Dwiky I. Bakhtiar, Wahyu S. Sipahutar, M Alvien Ghifari, Rishal Asri, Meqorry Yusfi, Tarmizi Taher, Aditya Rianjanu, Robi Kurniawan
Department of Materials Engineering, Institut Teknologi Sumatera, South Lampung 35365, Indonesia · Department of Chemistry, Faculty of Sciences, Institut Teknologi Sumatera, South Lampung 35365, Indonesia · Department of Energy System Engineering, Faculty of Industrial Technology, Institut Teknologi Sumatera, South Lampung 35365 · Department of Physics, Faculty of Mathematics and Natural Sciences, Universitas Andalas · Department of Environmental Engineering, Faculty of Infrastructure and Regional Technology, Institut Teknologi Sumatera, South Lampung 35365 · Center for Green and Sustainable Materials, Institut Teknologi Sumatera
Transcript
Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.
Kai: We're looking at the paper: "Effect of Mangosteen Peel (Garcinia mangostana L.) and Grass Jelly Leaf (Cyclea barbata L. Miers) Natural Dye Mixing Ratio on the Optical, Morphological, and Photovoltaic Properties of Dye-Sensitized Solar Cells (DSSC)".
Mira: Here's the gist of the paper. Dye-sensitized solar cells (DSSCs) are promising low-cost and environmentally friendly photovoltaic devices, especially when utilizing natural sensitizers.
Kai: This study explores the effect of concentration ratios of natural dyes extracted from mangosteen peel (MP) and grass jelly leaves (GJL) on the optical, morphological, and photovoltaic properties of DSSCs.
Mira: The composite dye with a 1:3 (MP:GJL) ratio yielded the highest PCE of 3.50%, demonstrating the synergistic effect of combining these natural sensitizers to broaden the light absorption spectrum.
Kai: Synergistic Optical Properties The UV-Vis absorption spectra showed that MP contributes to the UV-blue region (350-450), while GJL contributes to the red region (650-700 nm).
Title and authors: Kai: So we're looking at this paper right now, "Effect of Mangosteen Peel (Garcinia mangostana L.) and Grass Jelly Leaf (Cyclea barbata L. Miers) Natural Dye Mixing Ratio on the Optical, Morphological, and Photovoltaic Properties of Dye-Sensitized Solar Cells (DSSC)." It's about using natural dyes from mangosteen peel and grass jelly leaves to make these low-cost solar cells.
Mira: Yeah, it’s interesting because it looks at how mixing those two different sources affects everything: the light they absorb, how the film physically looks, and ultimately, how well they convert sunlight into electricity. We're talking about a real look at using natural materials instead of expensive synthetic dyes three <ref:2509.26622#pg1>.
Lev: I’m curious about what you mean by "everything," Mira. When you say optical properties and morphology, are we talking about the light absorption spectrum and the physical structure of the film, right? Because for us in hardware, those details matter a lot for how efficiently electrons get in and out.
Kai: Exactly. The paper looks at how different ratios of these two dyes change which colors of light they absorb best. It shows that mangosteen peel is good for the UV-blue part, like three hundred fifty to four hundred fifty nanometers, and grass jelly leaves handle the red region around six hundred fifty to seven hundred nanometers <ref:2509.26622#pg2>.
Mira: And the key finding there is that mixing them doesn't cause any major chemical changes between the dyes themselves. They just add up their absorption strengths, which is what makes this composite dye work better than either one alone two <ref:2509.26622#pg1>.
Lev: That's a relief for stability, because if they were reacting chemically, we’d have to worry about some nasty degradation during the cell fabrication process. But what about the actual performance numbers? What were the baseline efficiencies they got from just using mangosteen peel and just using grass jelly leaves individually?
Kai: The paper states that when you use just the mangosteen peel dye, you get a power conversion efficiency of two point seven five percent, and if you only use the grass jelly leaf dye, it's two point one two percent two <ref:2509.26622#pg1>. That gives us a baseline to compare against.
Mira: And then they test various volume ratios of the mix: they test three to one, two to one, one to one, two to one again at a different ratio, and finally three to one again for the best results two <ref:2509.26622#pg1>.
Lev: So what’s the headline number for this entire study? What is the best power conversion efficiency they actually achieved in this setup?
Title and authors: Kai: The composite dye with a three to one ratio of mangosteen peel to grass jelly leaf yielded the highest power conversion efficiency at three point five zero percent two <ref:2509.26622#pg2,The composite dye with a>. That's significantly higher than either natural dye alone, which is what they were comparing against.
Mira: That three point five zero percent number is really tied to that synergistic effect where you broaden the light absorption spectrum across both UV-blue and red regions two <ref:2509.26622#pg2,broaden the light absorption spectrum>. It’s not just additive performance; it’s something better because of the combination.
Lev: From an engineering standpoint, what does that improved light absorption mean for the actual device structure? Does it suggest something about how well these hybrid dyes stick to the titanium dioxide layer?
Kai: The paper points out that at the three to one ratio, you see a very uniform and homogenous nanoporous structure in the mixed-dye sample two <ref:2509.26622#pg1>. They found this suggests enhanced interfacial compatibility between these hybrid natural dyes and the titanium dioxide layer.
Mira: I agree. That better physical structure is what we want because it means better charge injection into the conduction band and less chance for charge recombination losses, which is a big issue in these devices two <ref:2509.26622#pg1>. It implies the optimized morphology at that ratio helps lower those losses.
Lev: But then there’s this part about stability, right? The cycling data shows that things change over time. What’s the trade-off they found between having high initial performance and keeping it stable over many cycles?
Kai: They observed a clear trade-off depending on the dye composition. Samples with a grass jelly leaf rich composition, specifically one to three and one to two ratios of mangosteen peel to grass jelly leaf, started with the highest efficiencies and kept more of that initial performance across several cycles six <ref:2509.26622#pg1>.
Mira: That’s interesting because it means the structure they got at those specific ratios is inherently more stable photochemically than the balanced one six <ref:2509.26622#pg1>. They found that the one to one mixture showed a very rapid collapse in power conversion efficiency after only a few cycles six <ref:2509.26622#pg1>.
Lev: Rapid collapse sounds bad for practical applications. It suggests that whatever mechanism is causing that failure in the one to one mix, it’s pretty sensitive. Are we talking about photobleaching or something else?
Title and authors: Kai: The mechanistic interpretation points toward a couple of things: photobleaching and molecular degradation, which reduces light absorption over time six <ref:2509.26622#pg1>. Plus, dye desorption from the titanium dioxide surface is another factor where weaker binding lets the dyes wash away into the electrolyte and causes a rapid loss of active dye coverage six <ref:2509.26622#pg1>.
Mira: So it’s not just one failure mode; it’s a combination of things happening at once. The authors suggest that optimizing a natural-dye DSSC requires balancing that initial high performance with long-term photochemical and interfacial stability six <ref:2509.26622#pg1>. It shows you can't just pick the best number on paper and assume it lasts.
Lev: That makes sense for real hardware. We’re building things to run reliably, not just hit a peak efficiency in a lab measurement. So, what is the big picture implication of finding this three point five zero percent PCE using natural dyes <ref:2509.26622#pg2>?
Kai: The main thing is that it shows the potential of these natural dye combinations as low-cost and environmentally friendly sensitizers for solar energy applications two <ref:2509.26622#pg1>. It proves that you can get performance comparable to some synthetic methods, but with materials that are much cheaper and less harmful.
Mira: And the synergy—broadening the absorption across complementary regions—is key. It suggests we should really focus on finding these natural dye pairs that complement each other well for future solar cell design two <ref:2509.26622#pg1>.
Lev: For me, it means that if we want to make real hardware using these dyes, we need to focus our effort not just on the highest initial efficiency, but on the ones that show better retention in cycling tests six <ref:2509.26622#pg1>. That’s where the real engineering work is needed.
Kai: So, to wrap up this paper on "Effect of Mangosteen Peel (Garcinia mangostana L.) and Grass Jelly Leaf (Cyclea barbata L. Miers) Natural Dye Mixing Ratio on the Optical, Morphological, and Photovoltaic Properties of Dye-Sensitized Solar Cells (DSSC)," we see that a three to one ratio gives three point five zero percent PCE two <ref:2509.26622#pg2,on the Optical, Morphological, and Photovoltaic Properties of>.
Mira: And we see that the key is balancing spectral coverage and initial efficiency with long-term stability, especially looking at those GJL-rich compositions which retain performance better over cycles six <ref:2509.26622#pg1>.
Lev: And from an engineering standpoint, it confirms that optimizing a natural-dye DSSC requires balancing spectral coverage and initial PCE with long-term photochemical and interfacial stability six <ref:2509.26622#pg1>. That’s what matters when you move from the lab to the real world.
The paper's summary: Kai: So we just talked about how mixing mangosteen peel and grass jelly leaf dyes can actually make a dye-sensitized solar cell perform better than either one alone, hitting a power conversion efficiency of three point five zero percent when you use that three to one ratio two.
Mira: Right. And the real story here is not just that it's more efficient, but why the way they blend those two different natural sources works so well optically. It’s about how they cover the light spectrum better than if you just used one dye.
Lev: From an error correction standpoint, if we think about this like a system with noisy channels, combining two different types of noise sources—the UV blue from the mangosteen and the red from the grass jelly—to cover a wider band is analogous to having more diverse inputs for your measurement.
Kai: Exactly. The paper shows that mangosteen peel handles those shorter wavelengths, say three hundred fifty to four hundred fifty nanometers, while grass jelly leaves handle those longer wavelengths, around six fifty to seven hundred nanometers two.
Mira: And the crucial assumption they make is that these two natural extracts don't have any weird chemical interactions when mixed. They just add up their absorption strengths without messing up each other’s fundamental way of absorbing light. That's a big part of why this approach is appealing for using natural materials two.
Lev: That assumption is key for us because if there was a reaction, we’d have to model the kinetics of that reaction, which adds complexity and uncertainty to the whole device modeling process.
Kai: The resulting composite dye then broadens the overall light-harvesting window across more of the visible spectrum. It moves it from being just one color specialist to being more panchromatic, which is what we want for a solar absorber two.
Mira: And that optical broadening leads directly into what they call morphological optimization. They look at how the physical film looks under different ratios, and they found that the balanced mixtures—like one to one and three to one—show a very uniform structure with no cracks six.
Lev: That uniformity is what we need for charge transfer. If you have a cracked film or patchy dye coverage, you get poor electron injection and high recombination losses, which would destroy your open circuit voltage two.
Kai: So the paper concludes that the three to one ratio gives the best initial power conversion efficiency of three point five zero percent because it optimizes both light absorption and charge collection simultaneously two.
Mira: But then they introduce a stability curve. They show that while high ratios give you great initial performance, they also look at how fast things break down over ten cycles six. They found that the grass jelly leaf rich compositions have better long-term retention than the perfectly balanced one to one mixture six.
Lev: That means we can’t just optimize for peak performance and forget about durability. We have to model the degradation mechanisms, like photobleaching or dye desorption from the titanium dioxide surface, because that's what causes those cycles to drop off rapidly in some configurations six.
Kai: So, the paper is showing that blending natural dyes is a promising route for low-cost cells, but we still have to figure out how to make them last. That sets up the next part of our discussion on stability modeling.
The paper's improvements: Kai: So we just covered how mixing those two natural dyes gives you a three point five zero percent efficiency at that three to one ratio two. And now we're looking at what the authors suggest they should actually *do* with this information for real-world hardware.
Mira: They aren't just stopping there with the numbers; they are proposing a way to predict exactly which ratio will give you the best power conversion efficiency, which is something we can use to guide material formulation in a lab two.
Lev: That makes sense because right now, trying every single ratio by hand is too time-consuming when you're building real hardware. Predicting the optimal combination based on the input ratios lets us skip a lot of trial and error for us, right?
Kai: They also suggest creating a system that can predict the morphological outcomes. If we know which ratio gives you that uniform nanoporous structure we talked about, we can design the synthesis process to aim for that specific physical shape instead of just hoping it happens by accident two.
Mira: That prediction needs to be based on the assumption that those structural improvements at one to one and three to one ratios correlate directly with better charge injection and less recombination losses into the electrolyte two.
Lev: We need a stability assessment module too, something that models photobleaching and molecular degradation over time during cycling, like what they saw in Figure six six. That’s how we move from a high initial efficiency measurement to knowing if it will actually run for months on a solar panel two.
Kai: So the implied improvement is moving away from just optimizing for peak power conversion efficiency and instead balancing that spectral coverage and initial performance with long-term photochemical and interfacial stability two.
Mira: That's the big conceptual shift they're pointing toward. It tells us that in natural dye systems, you can’t just pick the highest number on paper; you have to find the compositional window that maximizes both properties simultaneously two.
Lev: For our hardware work, this means our next step should be developing a predictive model for those MP to GJL ratios so we can design robust cells from the start instead of just testing a few fixed mixes two.
Kai: Exactly. It shows that using natural dye combinations is viable, but it requires us to treat the material formulation as an optimization problem balancing absorption and longevity two.
Conclusion: Kai: So we’re wrapping up on this paper about "Effect of Mangosteen Peel (Garcinia mangostana L.) and Grass Jelly Leaf (Cyclea barbata L. Miers) Natural Dye Mixing Ratio on the Optical, Morphological, and Photovoltaic Properties of Dye-Sensitized Solar Cells (DSSC)" by summarizing everything we just talked about.
Mira: Basically, the main point is that mixing those two natural dyes works synergistically to broaden the light absorption spectrum, leading to a higher power conversion efficiency of three point five zero percent at that three to one ratio.
Lev: It’s interesting how they found that while high ratios give you good initial performance, the stability drops quickly in some configurations because of things like dye desorption from the titanium dioxide surface six.
Kai: And the authors suggest that optimizing a natural-dye DSSC requires balancing that initial high performance with long-term photochemical and interfacial stability two.
Mira: That suggests we can't just chase the highest PCE number, but we have to look at how the material behaves over ten cycles six, especially those GJL rich compositions which showed better retention than the balanced one two.
Lev: I just want to say that for our error correction work, seeing that trade-off between instantaneous performance and operational stability is a really good lesson for designing any real hardware two.
Kai: It proves that using natural dye combinations is a viable path for low-cost cells, but we still have to figure out how to make them last through real use two.
Mira: And the synergy in light harvesting across those UV-blue and red regions really opens up ideas for designing future solar absorbers two.
Lev: We’re going to need models that predict that stability better than what they showed here, which is where the next set of studies on degradation mechanisms comes in.
More episodes
- 2610.32678-Probing the limits of materials design via a comprehensive crystal database of 14.6 million structures with 140 properties
- 2610.33595-Native-oxide-driven layer asymmetry, two-step switching and exchange bias in Co/Ir/Co trilayers
- 2503.19572-Spin models from nonlinear cellular automata
- 2606.23350-Irreversibility Enhances Quantum-Enhanced Markov-Chain Monte Carlo
- 2608.02744-Two-Parameter Ansatz for the Violation of Eigenstate Thermalization
- 2210.00806-Low- and high-energy localization landscapes for tight-binding Hamiltonians in two-dimensional lattices
- 2409.09625-Selective switch for band-edge alignments in pentagonal CdSeTe monolayer: Atom-valley locking
- 2606.20168-Norms, overlaps and Yangian descendants for the Haldane-Shastry spin chain
- 2512.19503-Strain-induced splitting of the CCDW-NCCDW phase transition in 1T-TaS 2
- 2307.12638-Strong localization of microwaves beyond two dimensions in aperiodic Vogel spirals