Threshold Properties in Degenerate Distributed Feedback Lasing

arXiv:2508.15955 · physics.optics · Submitted 2025-08-21 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: We're looking at the paper: "Threshold Properties in Degenerate Distributed Feedback Lasing".

Mira: Here's the gist of the paper. We advance the concept of degenerate distributed feedback (DDFB) lasing in a double grating photonic structure that operates near a degenerate band edge (DBE) to achieve a robust single-frequency lasing regime.

Kai: The DDFB laser is very attractive for various applications including communications, sensing, and spectroscopy.

Mira: Mechanism of Degeneracy The DDFB lasing mechanism leads to single-frequency lasing mode operation through a degeneracy between four different Bloch propagating and evanescent eigenmodes (whereas a DFB laser generally uses two propagating modes in the longitudinal grating).

Kai: This regime is associated with the formation of a degenerate band edge (DBE) in the Bloch dispersion relation of the waveguide.

Paper summary: Mira: So looking back at Threshold Properties in Degenerate Distributed Feedback Lasing by Herrero-Parareda, Furman, and Capolino, the authors are basically showing that you can advance the concept of degenerate distributed feedback lasing by using a double grating structure near a DBE.

Kai: They're emphasizing that this specific setup leads to four different Bloch eigenmodes becoming degenerate at the band edge because it's an exceptional point of fourth order.

Lev: And for the listener, what this means is that instead of just looking at two modes, you have these four modes interacting in a way that creates a robust single-frequency lasing regime.

Kai: The main implication is that this configuration allows for single-frequency lasing mode using a mirrorless cavity with minimal device footprint.

Mira: They are showing this path to achieving very low power requirements for these kinds of lasers, especially in long-range spectral communications, sensing, and spectroscopy applications.

Lev: And they show the scaling laws for quality factor scaling as N to the fifth power and lasing threshold scaling as one over N to the fifth power.

Kai: The paper says that these results are impressive because they demonstrate how leveraging regular band edge effects can enhance lasing efficiency, but this time they implemented it in a realistic double grating photonic structure.

Mira: And so while the authors admit the anomalous scaling laws are limited by fabrication tolerances, the overall result is that this DDFB laser may offer several advantages over traditional DFB lasers due to synchronized oscillation of the four degenerate waveguide modes.

Lev: So in simple terms, this paper proposes a method to build mirrorless cavities that can have much higher quality factors and much lower lasing thresholds than comparable mirrorless distributed feedback lasers.

Conclusion: Kai: So we're wrapping up this look at Threshold Properties in Degenerate Distributed Feedback Lasing by Herrero-Parareda, Furman, and Capolino.

Mira: Basically, they're talking about how you can get a very stable single-frequency laser mode using this double grating setup near a degenerate band edge.

Kai: They found that the key is getting four modes to line up at that band edge—it’s an exceptional point of fourth order—which makes the lasing much more robust.

Lev: From what I see, they are showing that even without mirrors, you can get a quality factor scaling with the fifth power of the length.

Mira: That's a big thing because it means your cavity gets much better at holding light as it gets longer than in a standard design where it scales with the third power.

Kai: And they also showed that because of this four-mode degeneracy, the lasing threshold drops off like one over N to the fifth power when you add gain.

Lev: That inverse fifth power scaling is what we need to hear if we want this to work on real hardware because it means a much lower power input is needed.

Mira: But they also have those caveats, right? They say that these specific scaling laws are really dependent on the fabrication tolerances and any small defects in the structure.

Kai: True, so while the theory looks fantastic for long-range sensing or spectroscopy, you can't just build this and expect perfect results without tight control over every single unit cell.

Lev: Yeah, so they've shown a path to mirrorless cavities that are more resilient to termination issues than traditional DFB lasers.

Mira: It really highlights how leveraging those regular band edge effects can give us better light-matter interaction for applications where stability is everything.

Kai: It opens the door for building lasers in communications and sensing that could be much smaller and less power hungry than what we're used to right now.

Albert Herrero-Parareda, Nathaniel Furman, Filippo Capolino

University of California, Irvine

physics.optics

Submitted: 2025-08-21

Updated: 2026-11-15

Comments: 13 pages, 8 figures

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 92/100

The gist: We advance the concept of degenerate distributed feedback (DDFB) lasing in a double grating photonic structure that operates near a degenerate band edge (DBE) to achieve a robust single-frequency…

Key concepts

Degenerate Band Edge (DBE)
The DBE is a special point in the waveguide's dispersion relation where four different Bloch eigenmodes become degenerate. This degeneracy forms a fourth-order exceptional point of degeneracy (EPD). Operating near this edge allows for unique lasing properties, as it involves four modes rather than the two modes typical in standard DFB lasers.
Degenerate Distributed Feedback (DDFB) Lasing
This is a lasing scheme achieved by exploiting the DBE. Instead of relying on two propagating modes like a standard DFB laser, the DDFB structure supports four different propagating and evanescent eigenmodes that become degenerate. This four-mode degeneracy enhances light-matter interaction, resulting in better performance metrics.
Quality Factor Scaling
The quality factor (Q) of the DDFB cavity scales with the fifth power of the double grating length (Q $\propto$ N$^5$). In contrast, a comparable DFB cavity's Q scales with the third power (N$^3$). This much faster scaling indicates that DDFB cavities are inherently more stable and have higher energy storage capabilities.
Lasing Threshold Scaling
The lasing threshold ($\alpha_{D,th}$) for the DDFB cavity scales inversely with the fifth power of the length ($\alpha_{D,th} \propto 1/N^5$). This ultralow threshold is due to the enhanced interaction between the four degenerate modes and gain, showing that lasing near this DBE resonance is significantly more efficient than near RBE resonances.

Terminology

Summary

We advance the concept of degenerate distributed feedback (DDFB) lasing in a double grating photonic structure that operates near a degenerate band edge (DBE) to achieve a robust single-frequency lasing regime. p. 0

Where the paper says it

1 Advancements in Degenerate Distributed Feedback Lasing Albert Herrero-Parareda , Nathaniel Furman , and Filippo Capolino Abstract—We advance the concept of degenerate distributed feedback (DDFB) lasing in a double grating photonic structure that operates near a degenerate band edge (DBE) to achieve a robust single-frequency lasing regime. The DBE is an exceptional point of degeneracy (EPD) of fourth order involving four coalescing Bloch eigenmodes.

The DDFB laser is very attractive for various applications including communications, sensing, and spectroscopy. p. 0
Where the paper says it

The work proposed here shows a path to single-frequency lasing mode using a mirrorless cavity with minimal device footprint. The DDFB laser is very attractive for various applications including communications, sensing, and spectroscopy.

p. 0
Where the paper says it

The work proposed here shows a path to single-frequency lasing mode using a mirrorless cavity with minimal device footprint. The DDFB laser is very attractive for various applications including communications, sensing, and spectroscopy.

Mechanism of Degeneracy

The DDFB lasing mechanism leads to single-frequency lasing mode operation through a degeneracy between four different Bloch propagating and evanescent eigenmodes (whereas a DFB laser generally uses two propagating modes in the longitudinal grating). This regime is associated with the formation of a degenerate band edge (DBE) in the Bloch dispersion relation of the waveguide. p. 0

Where the paper says it

lasing mode operation through a degeneracy between four different Bloch propagating and evanescent eigenmodes (whereas a DFB laser generally uses two propagating modes in the longitudinal grating). This regime, which is associated with the formation of a degenerate band edge (DBE) in the Bloch dispersion relation of the waveguide [10], [11], [12], [13], [14], [15], [16], [17], is characterized by vanishing group velocity, enhanced field amplitude [18], and enhanced local density of states [15].

The DBE is a fourth-order exceptional point of degeneracy (EPD) involving four coalescing Bloch eigenmodes. p. 0
Where the paper says it

1 Advancements in Degenerate Distributed Feedback Lasing Albert Herrero-Parareda , Nathaniel Furman , and Filippo Capolino Abstract—We advance the concept of degenerate distributed feedback (DDFB) lasing in a double grating photonic structure that operates near a degenerate band edge (DBE) to achieve a robust single-frequency lasing regime. The DBE is an exceptional point of degeneracy (EPD) of fourth order involving four coalescing Bloch eigenmodes.

EPDs in photonic systems can exist in the presence of balanced gain and loss, as in PT-symmetric systems. p. 0
Where the paper says it

EPDs are points in the parameter space of a system where the eigenvalues and eigenvectors collapse, or coalesce, on each other [19], [20]. EPDs in photonic systems can exist in the presence of balanced gain and loss, as in PT-symmetric systems [21], [22], and also in lossless and gainless structures as shown in [10], [11], even though the authors did not use the term EPD, and in [16], [23].

Performance Scaling with Length

The DDFB photonic cavity operating close to the DBE frequency is shown to display a large quality factor that scales with the fifth power of the cavity length. Upon the inclusion of gain, the DDFB cavity displays a low lasing threshold with an exceptional scaling as the inverse of the fifth power of the double grating length, i. p. 0

Where the paper says it

A DDFB photonic cavity operating close to the DBE frequency is shown to display a large quality factor that scales with the fifth power of the cavity length. Upon the inclusion of gain, the DDFB cavity displays a low lasing threshold with the exceptional scaling as the inverse of the fifth power of the double grating length, i.

e., αD,th ∝ 1/N5. p. 0
Where the paper says it

Upon the inclusion of gain, the DDFB cavity displays a low lasing threshold with the exceptional scaling as the inverse of the fifth power of the double grating length, i. , αD,th ∝ 1/N5 , where N is the number of waveguide unit cells making the mirrorless cavity.

The quality factors of the lossless and gainless DFB and DDFB cavities are shown in Figure 4 for different numbers of unit cells N. p. 3
Where the paper says it

The amplitude of the excited mode at the input port is scaled such that the total power carried by that mode equals 1 W. The quality factors of the lossless and gainless DFB and DDFB cavities are shown in Figure 4 for different numbers of unit cells N.

Both quality factors have the same period. p. 3
Where the paper says it

The dashed lines of the same color are the fitting functions that show the asymptotic N5 scaling of the DBE quality factor QD with DDFB waveguide length (orange) and the N3 scaling of the RBE quality factor QR with DFB waveguide length (blue). Both devices have the same period.

Lasing Threshold Comparison

The lasing threshold at the DBE resonance is significantly lower than those associated with the nearest RBE resonances. For N = 60, the lasing threshold at the DBE resonance is αD,th = 505 dB/cm, while that near the RBE resonance is αth = 2390 dB/cm. p. 6

Where the paper says it

3), we computed the lasing thresholds at the nearest resonances to the two exceptional points for N = 60 and N = 120 of the same structure. For N = 60, the lasing threshold at the DBE resonance (the closest one to the DBE frequency) is αD,th = 505 dB/cm, while that near the RBE resonance (closest to the RBE frequency) is αth = 2390 dB/cm, resulting in a 4.

The asymptotic lasing threshold law for the DDFB cavity is αD,th ∝ N −5. p. 7
Where the paper says it

(8) The anomalous αD,th ∝ N −5 threshold scaling law and the QD ∝ N5 asymptotic scaling of the quality factor shown in Figure 4 are bounded by the presence of defects and fabrication tolerances [17]. Figure 8 depicts the lasing thresholds of the DDFB (orange dots) and the DFB (blue dots) cavities with the same length N = 60 as a function of Γ as defined in Eq.

Advantages of the DDFB Design

The resulting frozen mode in the DDFB cavity exhibits comparatively larger field amplitude enhancement and group delay compared to the RBE-associated slow wave resonance. The quality factor of the DDFB cavity is larger than that of the DFB cavity for any N. p. 4

Where the paper says it

The observed N5 and N3 asymptotic scaling laws are consistent with the literature for both degeneracies [18], [14], [15], [16], [17], [24]. Besides the two completely different scaling laws, we also observe that the quality factor of the DDFB cavity is larger than that of the DFB cavity for any N, owing to the exceptional four-mode degeneracy.

This result demonstrates that the DBE-associated frozen mode regime experiences greater impedance mismatch at the cavity terminations compared to the RBE-associated resonance of the DFB design. p. 4
Where the paper says it

Besides the two completely different scaling laws, we also observe that the quality factor of the DDFB cavity is larger than that of the DFB cavity for any N, owing to the exceptional four-mode degeneracy. This result demonstrates that the DBE-associated frozen mode regime in the DDFB design experiences greater impedance mismatch at the cavity terminations compared to the RBE-associated resonance of the DFB design.

p. 4
Where the paper says it

Besides the two completely different scaling laws, we also observe that the quality factor of the DDFB cavity is larger than that of the DFB cavity for any N, owing to the exceptional four-mode degeneracy. This result demonstrates that the DBE-associated frozen mode regime in the DDFB design experiences greater impedance mismatch at the cavity terminations compared to the RBE-associated resonance of the DFB design.

Conclusion

In summary, mirrorless DDFB cavities display much larger quality factors and much lower lasing thresholds than comparable mirrorless DFB cavities of the same length. The quality factor and lasing thresholds of the DDFB cavity scale with waveguide length as the fifth power and inverse fifth power, respectively. p. 7

Where the paper says it

In summary, we have shown that mirrorless DDFB cavities display much larger quality factors and much lower lasing thresholds than comparable mirrorless DFB cavities of the same length. The quality factor and lasing thresholds of the DDFB cavity scale with waveguide length as the fifth power and inverse fifth power, respectively.

The anomalous αD,th ∝ N −5 threshold scaling law and the QD ∝ N5 asymptotic scaling of the quality factor shown in Figure 4 are bounded by the presence of defects and fabrication tolerances. p. 7
Where the paper says it

Indeed, when the trends are established for large-enough N, the ratio of the thresholds between the two cavities decreases asymptotically as αD,th αR,th ∼ a c 1 N2 . (8) The anomalous αD,th ∝ N −5 threshold scaling law and the QD ∝ N5 asymptotic scaling of the quality factor shown in Figure 4 are bounded by the presence of defects and fabrication tolerances [17].

p. 7
Where the paper says it

Indeed, when the trends are established for large-enough N, the ratio of the thresholds between the two cavities decreases asymptotically as αD,th αR,th ∼ a c 1 N2 . (8) The anomalous αD,th ∝ N −5 threshold scaling law and the QD ∝ N5 asymptotic scaling of the quality factor shown in Figure 4 are bounded by the presence of defects and fabrication tolerances [17].

The DDFB laser is potentially very attractive for various applications where these features are important, including long-range spectral communications, sensing, spectroscopy, and more. p. 8
Where the paper says it

Indeed, we have shown that the DBE resonance consistently has a lower lasing threshold than RBE resonances, indicating that lasing near the four-way degeneracy is preferred. These features of the DDFB lasing mechanism make the DDFB laser potentially very attractive for various applications where these features are important, including long-range spectral communications, sensing, spectroscopy, and more.

Pruning redundant reasoning tokens

The DDFB photonic structure advanced here features a double grating configuration where a standard grating is coupled with another grating. The second grating is obtained after performing a mirror operation with respect to the x, z plane and a translation s in the z direction. p. 1

Where the paper says it

DOUBLE GRATING DISTRIBUTED FEEDBACK WAVEGUIDE The DDFB photonic structure advanced here features a double grating configuration where a standard grating is coupled with another grating. The second grating is obtained after performing a mirror operation with respect to the x, z plane and a translation s in the z direction.

The waves in each optical grating couple with the waves in the other grating, forming a coupled double grating structure that supports four modes (when considering both directions). p. 1
Where the paper says it

The second grating is obtained after performing a mirror operation with respect to the x, z plane and a translation s in the z direction. The waves in each optical grating couple with the waves in the other grating, forming a coupled double grating structure that supports four modes (when considering both directions).

How the training signal is built

The modal dispersion relation of the longitudinal modes in the infinitely long double grating structure is obtained by modeling one unit cell of the waveguide in the eigenmode solver of CST Studio Suite with phase-shift periodic boundary conditions for a unit cell. The tapering is performed by adding two cells at either end of the structure whose corrugation height decreases by h/3 consecutively. p. 1

Where the paper says it

The two oppositelyfacing gratings are shifted by a distance s along z to break mirror symmetry, enabling the occurrence of the DBE that has a very flat band in the dispersion diagram provided by Eq. The tapering is performed by adding two cells at either end of the structure whose corrugation height decreases by h/3 consecutively.

This tapering aims to reduce radiation losses caused by abrupt changes at the edges of the cavity and potentially improve coupling with external waveguides. p. 1
Where the paper says it

To slightly mitigate the abrupt discontinuities at the cavity terminations, and also to partially decrease radiation induced by an abrupt change in waveguide periodicity [33], [34], we taper the last two unit cells on each side by reducing the corrugation height h by one-third, as shown in Fig. This tapering aims to reduce radiation losses caused by abrupt changes at the edges of the cavity and potentially improve coupling with external waveguides.

Where the gains come from

The gain region includes the cladding between the two gratings, which increases the interaction between the waves and the gain medium. The conversion between the bulk gain coefficient αg (in units of dB/cm) and the gain in terms of the imaginary part of a refractive index at an angular frequency ω is approximated by n′′g(ω) ≈ −αg(100/8. p. 6

Where the paper says it

The gain region includes the cladding between the two gratings, which increases the interaction between the waves and the gain medium [7]. The conversion between the bulk gain coefficient αg (in units of dB/cm) and the gain in terms of the imaginary part of a refractive index at an angular frequency ω is approximated by n ′′ g (ω) ≈ −αg(100/8.

686)(c0/ω). p. 6
Where the paper says it

The conversion between the bulk gain coefficient αg (in units of dB/cm) and the gain in terms of the imaginary part of a refractive index at an angular frequency ω is approximated by n ′′ g (ω) ≈ −αg(100/8. 686)(c0/ω) where c0 is the speed of light in vacuum.

The complex permittivity of the cladding, ε is written as ε = ε′ − jε′′, so its imaginary part is −ε′′ = Im(n2) = −2nbn′''g.

The resonance closest to the DBE frequency becomes closer and closer to the DBE frequency when increasing the cavity length, following the asymptotic law fr,D ∼ fD − hD 2π/N d 4. The smaller the flatness parameter hD is, the closer the DBE resonance frequency is to the DBE frequency. p. 3

Where the paper says it

The angle φ represents a reflection phase of each propagating mode at the edges of the cavity, where also the evanescent waves are strongly excited [13]. The smaller the flatness parameter hD is, the closer the DBE resonance frequency is to the DBE frequency.

Similarly, for the DFB cavity, the resonance closest to the RBE frequency is known as the “RBE resonance” with associated frequency fr,R ∼ fR − hR(π/2)/(N d) 2. p. 3
Where the paper says it

(Note that the asymptotic formula reported in [24], [16], [17], [23], [39] should have included also the term φ). Similarly, for the DFB cavity, the resonance closest to the RBE frequency is known as the “RBE resonance” with associated frequency fr,R ∼ fR − hR(π/2)/(N d) 2 .

The lasing threshold is obtained using full-wave electromagnetic simulations. To determine the lasing threshold of a finite-length DDFB cavity, we gradually increase the gain while monitoring the cavity field for unstable behavior. p. 6

Where the paper says it

Considering that the DBE quality factor scales asymptotically as QD ∼ N5 for increasingly large N [18], [14], [15], [16], [24], and that typically αth ∝ 1/Q [48], we anticipate the lasing threshold calculated at the DBE resonance exhibits an asymptotic scaling with waveguide length such that αD,th ∼ N −5 , consistent with the literature [15], [23]. To determine the lasing threshold of a finite-length DDFB cavity, we gradually increase the gain while monitoring the cavity field for unstable behavior.

This is done by tracking the poles of the S21 transmission parameter at the DBE resonance. p. 6
Where the paper says it

To determine the lasing threshold of a finite-length DDFB cavity, we gradually increase the gain while monitoring the cavity field for unstable behavior. This is done by tracking the poles of the S21 transmission parameter at the DBE resonance, as previously shown in Appendix A of [49], Appendix B of [50] or in [51] for other kinds of exceptional degeneracies.

The trend for the lasing thresholds versus DFB cavity length is established in a similar manner, leading to the fitting function αf it R,th(N) = 1/(cN3 + d). p. 7
Where the paper says it

This result shows that the lasing threshold follows the expected asymptotic scaling αD,th ∝ 1/(aN5 ) for large N. The trend for the lasing thresholds versus DFB cavity length is established in a similar manner, leading to the fitting function α f it R,th(N) = 1/(cN3 + d), (7) with c = 2.

The main implications of these trends are twofold. p. 7
Where the paper says it

Since the N −3 term dominates after N = 101, this result shows the asymptotic scaling threshold αR,th ∝ 1/(cN3 ) for large N. The main implications of these trends are twofold.

The DDFB cavity does not require waveguide reflectivity at its terminations. Even with vanishing reflectivity, the DDFB cavity has a Q comparable with that of the DFB cavity with higher reflectivity. p. 4

Where the paper says it

The DDFB cavity does not require waveguide reflectivity at its terminations. Even with vanishing reflectivity, the DDFB cavity has a Q comparable with that of the DFB cavity with higher reflectivity.

The quality factor of the DDFB cavity is more resilient to perturbations of its terminations than the DFB cavity. p. 6
Where the paper says it

7 the numerical burden, but their difference is even stronger for larger N, owing to the N4 and N2 asymptotic trends for field enhancement at DBE and RBE resonances, respectively, as shown in Ref. Additionally, the quality factor of the DDFB cavity is more resilient to perturbations of the reflectivity of its terminations than the quality factor of the DFB cavity.

The four-mode degeneracy responsible for the DDFB lasing mechanism displays an enhanced interaction with the gain medium, which results in a low lasing threshold that scales as the inverse fifth power with waveguide length. p. 8

Where the paper says it

Indeed, we have shown that the DDFB cavity exhibits a quality factor that scales as the fifth power of the double grating length, compared to the third power scaling of a comparable DFB cavity, and that it supports larger intracavity field amplitudes for the same length and quality factor. The four-mode degeneracy responsible for the DDFB lasing mechanism displays an enhanced interaction with the gain medium, which results in a low lasing threshold that scales as the inverse fifth power with waveguide length, clearly indicating a different lasing mechanism than in conventional lasers.

Indeed, we have shown that the DBE resonance consistently has a lower lasing threshold than RBE resonances, indicating that lasing near the four-way degeneracy is preferred. p. 8
Where the paper says it

The four-mode degeneracy responsible for the DDFB lasing mechanism displays an enhanced interaction with the gain medium, which results in a low lasing threshold that scales as the inverse fifth power with waveguide length, clearly indicating a different lasing mechanism than in conventional lasers. Indeed, we have shown that the DBE resonance consistently has a lower lasing threshold than RBE resonances, indicating that lasing near the four-way degeneracy is preferred.

p. 8
Where the paper says it

The four-mode degeneracy responsible for the DDFB lasing mechanism displays an enhanced interaction with the gain medium, which results in a low lasing threshold that scales as the inverse fifth power with waveguide length, clearly indicating a different lasing mechanism than in conventional lasers. Indeed, we have shown that the DBE resonance consistently has a lower lasing threshold than RBE resonances, indicating that lasing near the four-way degeneracy is preferred.

The DDFB cavity displays larger field amplitudes than the DFB cavity even when their loaded Q factors are the same. p. 7
Where the paper says it

A related discussion in [15] regarding the local density of states distribution within the cavity for the DBE and RBE cases supports these claims. Additionally, we have shown that the DDFB cavity displays larger field amplitudes than the DFB cavity even when their loaded Q factors are the same.

p. 7
Where the paper says it

A related discussion in [15] regarding the local density of states distribution within the cavity for the DBE and RBE cases supports these claims. Additionally, we have shown that the DDFB cavity displays larger field amplitudes than the DFB cavity even when their loaded Q factors are the same.

The authors are thankful to DS SIMULIA for providing CST Studio Suite. N. Furman acknowledges partial support from NSF-AFRL Internship Award No. p. 8

Where the paper says it

ACKNOWLEDGMENT The authors are thankful to DS SIMULIA for providing CST Studio Suite. Furman acknowledges partial support from NSF-AFRL Internship Award No.

ECCS-2030029. p. 8
Where the paper says it

Furman acknowledges partial support from NSF-AFRL Internship Award No. ECCS-2030029.

The paper is organized as follows: Section II defines the double grating design, following the approach outlined in [9]. p. 1
Where the paper says it

An analogous concept has been introduced at radio frequency in [27], [28] and experimentally demonstrated in [29]. This paper is organized as follows: Section II defines the double grating design, following the approach outlined in [9].

p. 1
Where the paper says it

An analogous concept has been introduced at radio frequency in [27], [28] and experimentally demonstrated in [29]. This paper is organized as follows: Section II defines the double grating design, following the approach outlined in [9].

In Section III, we introduce the design considerations and parameters for the waveguide to support a DBE in its modal dispersion relation and investigate its performance without gain. p. 1
Where the paper says it

This paper is organized as follows: Section II defines the double grating design, following the approach outlined in [9]. In Section III, we introduce the design considerations and parameters for the waveguide to support a DBE in its modal dispersion relation and investigate its performance without gain.

p. 1
Where the paper says it

This paper is organized as follows: Section II defines the double grating design, following the approach outlined in [9]. In Section III, we introduce the design considerations and parameters for the waveguide to support a DBE in its modal dispersion relation and investigate its performance without gain.

Section IV provides the inverse fifth power scaling of the lasing threshold with cavity length when gain is introduced in the double grating, and how the lasing threshold depends on the reflection coefficient at the two cavity terminations. p. 1
Where the paper says it

In Section III, we introduce the design considerations and parameters for the waveguide to support a DBE in its modal dispersion relation and investigate its performance without gain. Section IV provides the inverse fifth power scaling of the lasing threshold with cavity length when gain is introduced in the double grating, and how the lasing threshold depends on the reflection coefficient at the two cavity terminations.

p. 1
Where the paper says it

In Section III, we introduce the design considerations and parameters for the waveguide to support a DBE in its modal dispersion relation and investigate its performance without gain. Section IV provides the inverse fifth power scaling of the lasing threshold with cavity length when gain is introduced in the double grating, and how the lasing threshold depends on the reflection coefficient at the two cavity terminations.

The results are summarized in Section V. p. 1
Where the paper says it

The performance of a future DDFB laser compared to that of a comparable DFB laser is discussed throughout the paper. The results are summarized in Section V.

p. 1
Where the paper says it

The performance of a future DDFB laser compared to that of a comparable DFB laser is discussed throughout the paper. The results are summarized in Section V.

p. 1
Where the paper says it

The performance of a future DDFB laser compared to that of a comparable DFB laser is discussed throughout the paper. The results are summarized in Section V.

The work proposed here shows a path to single-frequency lasing mode using a mirrorless cavity with minimal device footprint. p. 0
Where the paper says it

, αD,th ∝ 1/N5 , where N is the number of waveguide unit cells making the mirrorless cavity. The work proposed here shows a path to single-frequency lasing mode using a mirrorless cavity with minimal device footprint.

The DDFB laser is very attractive for various applications including communications, sensing, and spectroscopy. The fundamental concept of leveraging regular band edge effects to enhance lasing efficiency was analyzed in [26]. p. 1
Where the paper says it

We additionally show that a DFB waveguide with the same structure and similar dimensions, supporting only a standing wave Bloch-mode degeneracy at a comparable frequency, exhibits a quality factor scaling as the cube of waveguide length and a lasing threshold scaling inversely with the cube of the length. The fundamental concept of leveraging regular band edge effects to enhance lasing efficiency was analyzed in [26].

Here, however, as in [9], we implement the DBE in a realistic double grating photonic structure. p. 1
Where the paper says it

A preliminary concept of the DBE laser was published in [23] based on an ideal coupled mode theory, ideal gain mechanism, and without specifying a realistic structure at optical frequencies. Here, however, as in [9], we implement the DBE in a realistic double grating photonic structure, combining the DFB mechanism with the degenerate mode.

The results are summarized in Section V. The DDFB laser may offer several advantages over traditional DFB lasers due to the synchronized oscillation of the four degenerate waveguide modes. p. 1
Where the paper says it

Consequently, a DDFB laser shows promise in lowpower optical telecommunication systems. In summary, the DDFB laser may offer several advantages over traditional DFB lasers due to the synchronized oscillation of the four degenerate waveguide modes.

These advantages include enhanced light-matter interactions, narrower line width, reduced lasing threshold, and increased resilience to external perturbations. p. 1
Where the paper says it

In summary, the DDFB laser may offer several advantages over traditional DFB lasers due to the synchronized oscillation of the four degenerate waveguide modes. These advantages include enhanced light-matter interactions, narrower line width, reduced lasing threshold, and increased resilience to external perturbations.

The DDFB laser is anticipated to achieve lasing with a lower lasing threshold without mirrors and to be more resilient to perturbations of its terminations than the DFB laser. p. 4
Where the paper says it

This result demonstrates that the DBE-associated frozen mode regime in the DDFB design experiences greater impedance mismatch at the cavity terminations compared to the RBE-associated resonance of the DFB design. Consequently, the DDFB laser is anticipated to achieve lasing with a lower lasing threshold without mirrors and to be more resilient to perturbations of its terminations than the DFB laser.

The paper is organized as follows: Section II defines the double grating design, following the approach outlined in [9]. In Section III, we introduce the design considerations and parameters for the waveguide to support a DBE in its modal dispersion relation and investigate its performance without gain. Section IV provides the inverse fifth power scaling of the lasing threshold with cavity length when gain is introduced in the double grating, and how the lasing threshold depends on the reflection coefficient at the two cavity terminations. The results are summarized in Section V.

We have advanced the concept of a degenerate distributed feedback (DDFB) lasing scheme for a cavity that operates in proximity to a DBE that is a special exceptional point of order four in a lossless and gainless multimode waveguide. The optical DDFB double grating is designed to have a degeneracy involving four propagating and evanescent optical modes, providing a degenerate distributed feedback. p. 8

Where the paper says it

CONCLUSION We have advanced the concept of a degenerate distributed feedback (DDFB) lasing scheme for a cavity that operates in proximity to a DBE that is a special exceptional point of order four in a lossless and gainless multimode waveguide. The optical DDFB double grating is designed to have a degeneracy involving four propagating and evanescent optical modes, providing a degenerate distributed feedback.

Consequently, for large N, a DDFB cavity exhibits a large quality factor, an ultralow lasing threshold, and a large stability to perturbations of its terminations. p. 8
Where the paper says it

The optical DDFB double grating is designed to have a degeneracy involving four propagating and evanescent optical modes, providing a degenerate distributed feedback. Consequently, for large N, a DDFB cavity exhibits a large quality factor, an ultralow lasing threshold, and a large stability to perturbations of its terminations.

Indeed, we have shown that the DDFB cavity exhibits a quality factor that scales as the fifth power of the double grating length, compared to the third power scaling of a comparable DFB cavity. p. 8
Where the paper says it

Consequently, for large N, a DDFB cavity exhibits a large quality factor, an ultralow lasing threshold, and a large stability to perturbations of its terminations. Indeed, we have shown that the DDFB cavity exhibits a quality factor that scales as the fifth power of the double grating length, compared to the third power scaling of a comparable DFB cavity, and that it supports larger intracavity field amplitudes for the same length and quality factor.

The four-mode degeneracy responsible for the DDFB lasing mechanism displays an enhanced interaction with the gain medium, which results in a low lasing threshold that scales as the inverse fifth power with waveguide length. Indeed, we have shown that the DBE resonance consistently has a lower lasing threshold than RBE resonances, indicating that lasing near the four-way degeneracy is preferred. The DDFB cavity displays larger field amplitudes than the DFB cavity even when their loaded Q factors are the same.

The quality factor of the DDFB cavity is larger than that of the DFB cavity for any N. This result demonstrates that the DBE-associated frozen mode regime experiences greater impedance mismatch at the cavity terminations compared to the RBE-associated resonance of the DFB design. The strong mismatch occurs because at the DBE resonance both the coalescing propagating and evanescent modes together are necessary to satisfy the boundary conditions at the two edges of the cavity. p. 4

Where the paper says it

Consequently, the DDFB laser is anticipated to achieve lasing with a lower lasing threshold without mirrors and to be more resilient to perturbations of its terminations than the DFB laser. This strong mismatch occurs because at the DBE resonance both the coalescing propagating and evanescent modes together are necessary to satisfy the boundary conditions at the two edges of the cavity.

This phenomenon results in having propagating modes with large magnitude causing the field enhancement at the interior of the cavity, away from the terminations. p. 4
Where the paper says it

Since they have almost coincident polarization states because of the four-wave degeneracy [18], [43], both types of waves have to be large to reconstruct the field at the terminations. This phenomenon results in having propagating modes with large magnitude causing the field enhancement at the interior of the cavity, away from the terminations.

The quality factors of the DDFB and DFB cavities can be controlled to some degree by resorting to the concept of waveguide impedance. Figure 6 shows that the loaded Q-factor of the DDFB cavity is tailored by adjusting the waveguide reflectivities Γ of its terminations. p. 5

Where the paper says it

6: Electric field amplitudes inside the passive (a) DDFB and (b) DFB cavities with N = 60, evaluated at their respective structured resonances as a function of the loaded Q-factor of the cavity. The loaded Q-factor is tailored by adjusting the waveguide reflectivities Γ of the terminations.

The DDFB cavity necessitates lower waveguide reflectivities to have a Q of the same value as that of the DFB cavity. p. 5
Where the paper says it

than a DFB cavity of the same length, displaying a larger scaling power with waveguide length (QD ∼ N5 as opposed to QR ∼ N3 ). When the reflectivity of their terminations is tailored, the DDFB cavity necessitates lower waveguide reflectivities to have a Q of the same value as that of the DFB cavity.

The quality factor and lasing thresholds of the DDFB cavity scale with waveguide length as the fifth power and inverse fifth power, respectively. The DFB cavity, in contrast, scales as N3 and N −3 instead. p. 7

Where the paper says it

The quality factor and lasing thresholds of the DDFB cavity scale with waveguide length as the fifth power and inverse fifth power, respectively. In the DFB cavity, they scale as N3 and N −3 instead.

The ratio of the thresholds between the two cavities decreases asymptotically as αD,th/αR,th ∼ a/c 1/N2. p. 7
Where the paper says it

This suggests possibilities for device miniaturization and reduced power consumption. Indeed, when the trends are established for large-enough N, the ratio of the thresholds between the two cavities decreases asymptotically as αD,th αR,th ∼ a c 1 N2 .

The anomalous αD,th ∝ N −5 threshold scaling law and the QD ∝ N5 asymptotic scaling of the quality factor shown in Figure 4 are bounded by the presence of defects and fabrication tolerances.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved AI system can design mirrorless DDFB lasers with minimal device footprint by leveraging a degenerate distributed feedback (DDFB) lasing scheme for a cavity that operates in proximity to a DBE that is a special exceptional point of order four in a lossless and gainless multimode waveguide.

  2. Improved AI system can predict the scaling laws for quality factor and lasing threshold with high accuracy, specifically predicting that the DDFB cavity exhibits a quality factor that scales as the fifth power of the double grating length, compared to the third power scaling of a comparable DFB cavity.

  3. Improved AI system can optimize gain requirements for lasing by calculating thresholds based on specific resonance types, showing that the lasing threshold at the DBE resonance is significantly lower than those associated with the nearest RBE.

  4. Improved AI system can predict and quantify field enhancement in photonic cavities, demonstrating that the maximum field enhancement in a cavity with a DBE is generally larger than that of a comparable cavity with an RBE having the same Q factor, length, and analogous topologies.

  5. Improved AI system can assess the robustness of laser performance against fabrication variations by showing that the DDFB cavity displays significantly more resilience to perturbations of its terminations than the DFB cavity.

Abstract

We investigate threshold properties in degenerate distributed feedback (DDFB) lasing in a double-grating photonic structure that operates near a degenerate band edge (DBE) with the potential to support robust single-frequency lasing. The DBE is an exceptional point degeneracy (EPD) of fourth order involving four coalescing Bloch eigenmodes. We also provide an analytical demonstration that, for a four-mode system, a quartic flat Bloch dispersion implies the coalescence of the four eigenvectors into a single eigendirection, without explicitly calculating them. Unlike previous studies based on coupled-mode theory, here the realistic double grating is studied using a full-wave method. A DDFB photonic cavity operating close to the DBE frequency is shown to display a large quality factor that scales with the fifth power of the cavity length. Upon the inclusion of gain, the DDFB cavity displays a low lasing threshold with the exceptional scaling as the inverse of the fifth power of the double-grating length, i.e., α D,th proportional to 1/N 5, where N is the number of waveguide unit cells making the mirrorless cavity. These results suggest the potential for compact, single-frequency lasing using a mirrorless cavity with minimal device footprint. The DDFB laser is very attractive for various applications including communications, sensing, and spectroscopy.

Sources

Related papers