Feedback suppression in 405 nm superluminescent diodes via engineered scattering

arXiv:2504.04272 · physics.optics · Submitted 2025-04-05 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: I'm Kai.

Mira: And I'm Mira, here with Lev.

Kai: We're looking at the paper: "Feedback suppression in 405 nm superluminescent diodes via engineered scattering".

Mira: Here's the gist of the paper. Superluminescent diodes are electrically pumped semiconductor devices in which light emission is produced by the amplified spontaneous emission (ASE) obtained along a waveguide <ref:2504.04272#pg2> The paper proposes and demonstrates the introduction of scattering defects in the device’s waveguide as a method for feedback inhibition <ref:2504.04272#pg2> This novel fabrication approach involves performing pulsed laser ablation on a commercial 405 nm GaN laser diode to create a superluminescent diode with good performances for low coherence applications <ref:2504.04272#pg2>.

Kai: Device Modification The modification process involved controlled pulsed laser ablation of the ridge waveguide of a commercially available GaN LD to introduce scattering defects <ref:2504.04272#pg2> The ablation was performed using a mode-locked, frequency-doubled (532 nm) Nd:YAG laser with specific parameters <ref:2504.04272#pg2>.

Mira: The resulting modified LD exhibited several key structural features <ref:2504.04272#pg2>: 1.

Kai: The device featured a narrow ridge waveguide, about 8 μm in width <ref:2504.04272#pg2>.

Title and authors: Kai: They bored a pit into the metallic contact on top of the ridge and dug a pit into the ridge waveguide with rough walls and irregular features >

Lev: They also measured some divergence angles for those beam profiles along parallel and orthogonal directions, finding them to be eleven point six degrees and thirty four point five degrees respectively >

The paper's summary: Kai: We've covered the setup and some of the initial measurements. Now let's focus on what they summarize in this paper, which is basically about introducing scattering defects into the light amplification path to break a feedback loop. It’s a novel way to suppress lasing action without needing complex external designs.

Mira: Right, so they are arguing that scattering elements can be a practical tool for feedback and lasing suppression in optical cavities, which is something that hasn't been reported much before >

Lev: The paper claims the added value of this method is its simplicity because it can be performed after completing the fabrication of a commercial diode and doesn't require standard fabrication techniques >

Kai: This directly addresses the limitations we talked about earlier, like needing very low reflection coefficients for anti-reflection coatings or dealing with loss compensation in absorber sections >

Mira: They are showing that this approach avoids optical feedback and lasing action while keeping the original diode mirrors untouched, which is a key point because it simplifies things for making these devices >

Lev: From an engineering standpoint, this simplicity means you don't have to worry about the complex steps of achieving perfect anti-reflection coatings or managing loss compensation in absorbers >

The paper's improvements: Kai: The primary improvement they suggest is that fabrication of superluminescent diodes can be simplified by using pulsed laser ablation of a commercial LD to introduce scattering defects into the optical waveguide >

Mira: That’s the mechanism. By introducing these scattering defects, you create a disordered cavity, and this leads to peaks that are randomly distributed in frequency and mode competition, causing them to vary with current >

Lev: The paper states that this behavior is characteristic of disordered cavities rather than the periodic modulation you see in an ordinary Fabry-Perot cavity >

Kai: And they also showed that the loss of spatial coherence is quantified by the speckle contrast C, where a narrower distribution indicates a lower degree of spatial coherence >

Mira: They link this to how spectral narrowing from twelve nanometers to five point seven nanometers as current varies is attributed to losses added by the modification process from pulsed laser ablation >

Lev: So the performance improvements are directly linked to those scattering walls and irregular features in the optical waveguide, leading to peaks that are randomly distributed in frequency and mode competition that vary with current >

Conclusion: Kai: So to wrap up on this paper, they propose a new method for fabricating GaN SLD by introducing scattering defects into the light amplification path to break the feedback loop >

Mira: They demonstrate that scattering elements can be a practical tool for feedback and lasing suppression in optical cavities, which has been scarcely reported to date >

Lev: The added value is its simplicity because it can be performed after completion of the fabrication process of a commercial LD and does not require the adoption of standard fabrication techniques >

Kai: It suggests that this approach will help the development of novel techniques for SLD fabrication due to its simple implementation >

Mira: This method is important because it’s about overcoming limitations of conventional methods for suppressing optical feedback in SLDs >

Lev: For real hardware, this is important because you can just add these defects without having to overhaul the whole fabrication process >

Kai: That's our look at this paper on Feedback suppression in four hundred five nm superluminescent diodes via engineered scattering <ref:2504.04272#pg1,Feedback suppression in 405 nm superluminescent diodes via engineered scattering>. It’s a method that leverages simple laser ablation to get a better result for low coherence applications.

ANDREA MARTíNEZ PACHECO, ANTONIO CONSOLI, CEFE LóPEZ

Instituto de Ciencia de Materiales de Madrid (ICMM) · Escuela de Ingeniería de Fuenlabrada (EIF), Universidad Rey Juan Carlos (URJC)

physics.optics

Submitted: 2025-04-05

Updated: 2025-04-05

DOI: 10.1088/2515-7647/ae42a5

License: http://arxiv.org/licenses/nonexclusive-distrib/1.0/

Importance score: 76/100

The gist: Superluminescent diodes are electrically pumped semiconductor devices in which light emission is produced by the amplified spontaneous emission (ASE) obtained along a waveguide <ref:2504.04272#pg2>…

Key concepts

Superluminescent Diodes (SLDs)
These are light sources that produce light through amplified spontaneous emission along a waveguide. They are valued for their low coherence, making them useful for applications like optical coherence tomography and displays where precise light control is needed.
Scattering Defects
These are intentional pits and irregular features created in the device's waveguide using pulsed laser ablation. These defects disrupt the light path, which is used here to break the optical feedback loop that causes lasing in standard devices.
Spatial Coherence (Speckle Contrast C)
This measures how consistent the light pattern is across space. A lower speckle contrast value indicates lower spatial coherence, meaning the light produced by this modified diode is less uniform and more suitable for certain low-coherence applications.

Terminology

Summary

Superluminescent diodes are electrically pumped semiconductor devices in which light emission is produced by the amplified spontaneous emission (ASE) obtained along a waveguide <ref:2504. p. 004272#pg2> The paper proposes and demonstrates the introduction of scattering defects in the device’s waveguide as a method for feedback inhibition <ref:2504. p. 004272#pg2> This novel fabrication approach involves performing pulsed laser ablation on a commercial 405 nm GaN laser diode to create a superluminescent diode with good performances for low coherence applications <ref:2504. p. 004272#pg2>.

Device Modification

The modification process involved controlled pulsed laser ablation of the ridge waveguide of a commercially available GaN LD to introduce scattering defects <ref:2504.04272#pg2> The ablation was performed using a mode-locked, frequency-doubled (532 nm) Nd:YAG laser with specific parameters <ref:2504. p. 104272#pg2>.

The resulting modified LD exhibited several key structural features <ref:2504. p. 204272#pg2>:

  1. The device featured a narrow ridge waveguide, about 8 μm in width <ref:2504. p. 104272#pg2>.

  2. A Fabry-Perot (FP) cavity length of 790 μm was present <ref:2504. p. 104272#pg2>.

  3. The ablation process created a pit into the ridge waveguide with rough walls and irregular features <ref:2504. p. 104272#pg2>.

The maximum output power measured for the modified device was 2 mW at 350 mA <ref:2504. p. 104272#pg2>.

Emission Characteristics

Spectral measurements revealed significant changes in emission properties after modification <ref:2504.04272#pg2>

- The central wavelength of emission blue-shifted from 406.65 nm to 402. p. 115 nm when current was varied between 20 mA to 350 mA <ref:2504. p. 104272#pg2>. This shift is attributed to the band filling effect caused by increasing carrier density in the ASE regime <ref:2504. p. 104272#pg2>. The full width at half maximum (FWHM) of the emission spectra narrowed from 12 nm to 5. p. 17 nm as current increased <ref:2504. p. 104272#pg2>. The spectral profiles consisted of bell-shaped curves with few nanometers width and superimposed narrow peaks not to be mistaken for noise, understood as ASE with residual modes from the disordered cavity formed after ablation <ref:2504. p. 104272#pg2>. 3D profile measurements showed divergence angles of 11. p. 06 ° and 34.5 ° along the parallel and perpendicular directions, respectively, which is a small increase with respect to the original LD <ref:2504. p. 204272#pg2>. The speckle contrast was reduced for the SLD compared to the original LD, resulting in lower spatial coherence <ref:2504. p. 204272#pg2>. A narrower distribution of the probability density function was observed for the SLD, indicating a lower degree of spatial coherence with C. p. 2 The speckle contrast C was greater in the LD than in the SLD for all values, which is understood as a lower degree of spatial coherence in the fabricated device <ref:2504. p. 204272#pg2>. 3. CONCLUSIONS

A new method for the fabrication of GaN SLD is proposed and demonstrated by introducing scattering defects into the light amplification path to break the feedback loop <ref:2504.04272#pg2>. The approach demonstrates that scattering elements can be a practical tool for feedback and lasing suppression in optical cavities, which has been scarcely reported to date <ref:2504. p. 204272#pg2>. The added value of this method is its simplicity, as it can be performed after completion of the fabrication process of a commercial LD and does not require the adoption of standard fabrication techniques <ref:2504. p. 304272#pg2>. The research suggests that this approach will help the development of novel techniques for SLD fabrication due to its simple implementation <ref:2504. p. 204272#pg2>.

Where the gains come from

The performance improvements are directly linked to the introduction of scattering walls and irregular features into the optical waveguide <ref:2504.04272#pg2>. The resulting disordered cavity leads to peaks that are randomly distributed in frequency and mode competition, causing them to vary with current <ref:2504. p. 204272#pg2>. This behavior is characteristic of disordered cavities rather than the periodic modulation seen in an ordinary FP cavity <ref:2504. p. 204272#pg2>. The loss of spatial coherence is quantified by the speckle contrast C, where a narrower distribution indicates a lower degree of spatial coherence <ref:2504. p. 204272#pg2>. The spectral narrowing from 12 nm to 5. p. 17 nm is attributed to the losses added by the modification process by pulsed laser ablation <ref:2504. p. 104272#pg2>.

Pruning redundant reasoning tokens

The paper focuses on overcoming the limitations of conventional methods for suppressing optical feedback in SLDs <ref:2504.04272#pg2>. Conventional approaches include anti-reflection coatings, bending or tilting the waveguide, adding an absorber section, or roughening the facet surface <ref:2504. p. 004272#pg2>. The authors argue that these methods present challenges such as requiring very low reflection coefficients for anti-reflection coatings or being unsuitable for high injection currents due to loss compensation in absorber sections <ref:2504. p. 004272#pg2>. The proposed method is novel because it introduces scattering defects via pulsed laser ablation of the ridge waveguide, avoiding optical feedback and lasing action while keeping the original LD mirrors untouched <ref:2504. p. 004272#pg2>.

How the training signal is built

The device modification procedure was detailed as follows <ref:2504.04272#pg2>:

  1. The original GaN LD, Ushio HL40053MG, was opened for inspection and modification <ref:2504. p. 104272#pg2>.

  2. A mode-locked, frequency-doubled (532 nm) Nd:YAG laser was used to perform controlled pulsed laser ablation on the ridge waveguide <ref:2504. p. 104272#pg2>.

  3. The pulsed laser delivered 80 μJ of pulse energy with a diameter of 18 μm, located about 50 μm from the back mirror <ref:2504. p. 104272#pg2>.

The characterization involved measuring output power with a calibrated photodiode and spectral measurements using a spectrometer connected to an optical fiber <ref:2504. p. 104272#pg2>. The emission profiles were recorded with a CMOS camera for beam characterization <ref:2504. p. 204272#pg2>.

References

  1. H. Lu, O. Alkhazragi, Y. p. 3 Wang, N. Almaymoni, W. p. 3 Yan, W. H. Gunawan, H. p. 3 Lin, T.-Y. Park, T.-Y., K., and B., Low-coherence semiconductor light sources: devices and applications, npj Nanophotonics 1, 9 (2024) <ref:2504.04272#pg2>.

  2. S. Stanczyk, A. p. 3 Kafar, D. Schiavon, S. p. 3, T., and P., Edge Emitting Laser Diodes and Superluminescent Diodes, in Nitride Semiconductor Technology (2020) <ref:2504.04272#pg2>.

  3. F. Kopp, C. Eichler, A. p. 3 Lell, S., J., B., C., T., U., and U., Blue superluminescent light-emitting diodes with output power above 100mW for picoprojection, Jpn. J. Appl. Phys. 52, (2013) <ref:2504. p. 304272#pg2>.

  4. M. Rossetti, A. p. 3, A., M., C., N., M., D., and C., RGB Superluminescent Diodes for AR MicroDisplays, in Digest of Technical Papers - SID International Symposium (2018), Vol. 49 <ref:2504.04272#pg2>.

  5. R. A. Costa, M., Skaf, L., A. S., D., J., C., D., and M., Retinal assessment using optical coherence tomography, Prog. Retin. Eye Res. 25, (2006) <ref:2504. p. 304272#pg2>.

  6. A. A. Alatawi, J. p. 3 A Holguin-Lerma, C. p. 3, H., K., C., S., R., A M Albadri, A Y Alyamani, T. p. 3 K Ng, and B S Ooi, High-power blue superluminescent diode for high CRI lighting and high-speed visible light communication, Opt. Express 26, (2018) <ref:2504. p. 304272#pg2>.

  7. M. Dong, S., Y., J., C., D., S., W., Y Hou, Z Li, J Zhang, J Shi, N Chi, and C Shen, High-Speed GaN-Based 405 nm Violet Superluminescent Diode with Tilted Facet for Visible Light Communications, Phys. Status Solidi Appl. p. 3 p. 3 Mater. Sci. 221, (2024) <ref:2504. p. 304272#pg2>.

  8. J Nayak, Fiber-optic gyroscopes: From design to production [Invited], Appl. Opt. 50, (2011) <ref:2504. p. 304272#pg2>.

  9. G R Goldberg, A Boldin, S M L Andersson, P Ivanov, N Ozaki, R J E Taylor, D T D Childs, K M Groom, K L Kennedy. p. 3, and R A Hogg, Gallium Nitride Superluminescent Light Emitting Diodes for Optical Coherence Tomography Applications, IEEE J. Sel. Top. Quantum Electron. p. 3 23, (2017) <ref:2504. p. 304272#pg2>.

  10. E Feltin, A Castiglia, G Cosendey, L Sulmoni, J F Carlin, N Grandjean, M Rossetti, J Dorsaz, V Laino, M Duelk. p. 3, and C Vélez. p. 3, Broadband blue superluminescent light-emitting diodes based on GaN, Appl. Phys. Lett. 95, 16–18 (2009) <ref:2504. p. 004272#pg2>.

  11. M T Hardy, K M Kelchner, Y Da Lin, P S Hsu, K Fujito, H Ohta, J S Speck. p. 3, S Nakamura. p. 3, and S P DenBaars. p. 3, m-plane GaN-based blue superluminescent diodes fabricated using selective chemical wet etching, Appl. Phys. Express 2, 1–3 (2009) <ref:2504. p. 304272#pg2>.

  12. A Kafar, S Stanczyk, D Schiavon, T Suski, and P Perlin. p. 3 p. 3 p. 3 p. 3, Review—Review on Optimization and Current Status of (Al,In)GaN Superluminescent Diodes, ECS J. Solid State Sci. p. 3 Technol. 9, (2020) <ref:2504. p. 304272#pg2>.

  13. N Feng, M Lu, S Sun, A Liu, X Chai, X Bai, J Hu., and Y Zhang. p. 3, LightEmitting Device Based on Amplified Spontaneous Emission, Laser Photonics Rev. 17, (2023) <ref:2504. p. 304272#pg2>.

  14. K Holc, Ł Marona, R Czernecki, M Boćkowski, T Suski, S Najda. p. 3, and P Perlin., Temperature dependence of superluminescence in InGaNbased superluminescent light emitting diode structures, J. Appl. Phys. 108, (2010) <ref:2504. p. 304272#pg2>.

  15. C Shen, C Lee, T K Ng, S Nakamura, J S Speck. p. 3, S P DenBaars. p. 3, A Y Alyamani, M M El-desouki, and B S Ooi. p. 3 p. 3, High-speed 405-nm superluminescent diode (SLD) with 807-MHz modulation bandwidth, Opt. Express 24, (2016) <ref:2504. p. 304272#pg2>.

  16. A Kafar, S Stańczyk, S Grzanka, R Czernecki, M Leszczyński, T Suski. p. 3, and P Perlin., Cavity suppression in nitride based superluminescent diodes, J. Appl. Phys. 111, (2012) <ref:2504. p. 304272#pg2>.

  17. D Marcuse, Reflection Loss of Laser Mode from Tilted End Mirror, J Light. Technol. 7, (1989) <ref:2504.04272#pg2>.

  18. G A Alphonse, Design of high-power superluminescent diodes with low spectral modulation, in Test and Measurement Applications of Optoelectronic Devices (2002), Vol. 4648 <ref:2504.04272#pg2>.

  19. A Kafar, S Stańczyk, P Wis̈niewski, T Oto, I Makarowa, G Targowski, T Suski. p. 3, and P Perlin., Design and optimization of InGaN superluminescent diodes, Phys. Status Solidi Appl. Mater. Sci. 212, (2015) <ref:2504. p. 304272#pg2>.

  20. C Shen, T K Ng, J T Leonard, A Pourhashemi, S Nakamura, S P DenBaars. p. 3, J S Speck., A Y Alyamani, M M El-desouki, and B S Ooi., High-brightness semipolar (2021¯) blue InGaN/GaN superluminescent diodes for droop-free solid-state lighting and visible-light communications, Opt. Lett. 41, (2016) <ref:2504. p. 304272#pg2>.

  21. A Kafar, S Stanczyk, G Targowski, T Suski, and P Perlin. p. 3, Gain saturation in InGaN superluminescent diodes, Gall. Nitride Mater. p. 3 Devices IX 8986, 89860P (2014) <ref:2504. p. 304272#pg2>.

  22. R Cahill, P P Maaskant, M Akhter, and B Corbett. p. 3, High power surface emitting InGaN superluminescent light-emitting diodes, Appl. Phys. Lett. 115, (2019) <ref:2504. p. 304272#pg2>.

  23. Fundamentals of semiconductor lasers, Springer Ser. Opt. Sci. 93, (2014) <ref:2504. p. 304272#pg2>.

  24. A Consoli, N Caselli, and C López. p. 3, Electrically driven random lasing from a modified Fabry–Pérot laser diode, Nat. Photonics 16, 219–225 (2022) <ref:2504. p. 304272#pg2>.

  25. A Consoli, P D García, and C López. p. 3, Tuning the emission properties.

  26. The data that support the plots within this paper are available from the corresponding authors upon reasonable request <ref:2504. p. 304272#pg2>.

--- Page 1 ---

Feedback suppression in 405 nm superluminescent diodes via engineered scattering <ref:2504.04272#pg2> ANDREA MARTÍNEZ PACHECO, ANTONIO CONSOLI, CEFE LÓPEZ <ref:2504. p. 004272#pg2>.

Superluminescent diodes are promising devices for applications in which low coherence, high efficiency, small footprint and good optoelectronic integration are required Blue emitting superluminescent diodes with good performances and easy fabrication process are sought for next generation solid state lighting devices, micro-projectors and displays. p. 0

These devices are laser diodes in which the optical feedback is inhibited, and lasing action avoided. p. 0

Conventional fabrication processes minimize optical feedback by ad-hoc designs, e. p. 0g., anti-reflection coating, tilted waveguide or absorber sections, requiring specific fabrication steps. p. 0

In this work, we propose and demonstrate the introduction of scattering defects in the device’s waveguide as a method for feedback inhibition. p. 0

By performing pulsed laser ablation on a commercial 405 nm GaN laser diode we demonstrate a superluminescent diode, featuring a maximum output power of 2 mW and a spectral width of 5. p. 07 nm.

--- Page 2 ---

A. Device modification

The original device is a commercially available GaN LD emitting at 405 nm (Ushio HL40053MG).

The LD threshold current is 90 mA and maximum output power of 300 mW at 400 mA. p. 1

The LD is mounted on a metallic L-shaped holder fabricated ad-hoc which allows imaging the top surface of the dice, observing the FP cavity from above. p. 1

The modification procedure consisted of controlled pulsed laser ablation of the ridge waveguide which is accessible from above the device. p. 1

The ablation process was performed by using a mode-locked, frequency-doubled (532 nm) Nd:YAG laser with specific parameters. p. 1

The pulsed laser delivered 2 pulses with pulse energy of 80 μJ, and diameter 18 μm, located at about 50 μm from the back mirror. p. 1

In Fig. 1a, a top view of the modified LD is provided. p. 1

The LD has a narrow (about 8 μm) ridge waveguide (dim, narrow, long, rectangle at the bottom of the top electrode patch) and a Fabry-Perot (FP) cavity length of 790 μm. p. 1

The ablation process bored a hole into the metallic contact on top of the ridge and dug a pit into the ridge waveguide, with rough walls and irregular features. p. 1

The 3D profile of the ablated region has been obtained by optical profilometry. p. 1

Transverse (x-axis) and longitudinal (y-axis) cross sections are shown in Fig. p. 1 1d and 1e, respectively. p. 1

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Fabrication of superluminescent diodes can be simplified by using pulsed laser ablation of a commercial LD to introduce scattering defects into the optical waveguide. This method avoids complex fabrication steps like anti-reflection coating, tilted waveguide or absorber sections, which are often challenging in real structures.

  2. The improved AI system can design novel low coherence applications, such as pico-projectors [3], displays [4], optical coherence tomography (OCT) [5], visible light communications [6,7] and fiber optic gyroscopes [8], by leveraging the demonstrated performance of the new SLDs.

  3. The system can predict emission properties by modeling gain dependence using a simple expression of the gain g(I), which is defined as g(I) = 1 – exp(g0·I), allowing for better control over spectral characteristics, such as observing a spectral narrowing from 12 nm to 5.7 nm with current variation.

  4. The system can assess spatial coherence by calculating the speckle contrast C, where C gives direct information regarding the number of modes creating the pattern, N = C–2 [26], enabling it to quantify the reduction in spatial coherence achieved by processing compared to original LDs.

Related papers