Cavitation near the oscillating piezoelectric plate in water

arXiv:1711.05234 · physics.flu-dyn · Submitted 2017-11-14 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: I'm Kai.

Mira: And I'm Mira, here with Lev.

Kai: We're looking at the paper: "Cavitation near the oscillating piezoelectric plate in water".

Mira: Here's the gist of the paper. Cavitation near the oscillating piezoelectric plate in water proposes a method to create a thin layer of liquid filled with bubbles near a wall using ultrasonic vibrations and shows that cavitation develops under certain conditions It is known that gas bubbles on the surface bounding a fluid flow can change the coefficient of friction and affect the parameters of the boundary layer Such bubbles are intensely formed in the liquid as a result of cavitation in areas of negative pressure In this paper, we propose a method for generating cavitation in the near-wall region We will show that cavitation can be generated in the boundary layer near the wall by performing ultrasonic vibrations Such oscillations can be excited, for example, by a piezoelectric plate glued to the wall bounding a liquid Vibrations and Sound Wave Generation Consider generation of sound in water caused by transverse vibrations of an immersed flat plate In the linear approximation without damping, equations describing the oscillations of a liquid can be written in the form

4: Assuming the plate vibrations to be harmonic a(t) = a sin(ωt) = 0, from the no-slip condition it follows from (1) that ρ',P',u' ∝ cos(ωt - kx), where s k = ω / c The corresponding amplitudes of the normal velocity and pressure of the liquid on the oscillating boundary are 0 u = ωa and 0 P c a = ρ s Bubble Nucleation Mechanism It is known that cavitation can occur in the rarefaction regions of a sound wave An expression for the nucleation rate in the negative pressure region is as follows

9: Assuming the "Lorentzian" dependence of the surface tension coefficient σ on the bubble radius Rb

9: From (5) we find the value of the bubble radius Rcr at which Wb reaches a maximum at fixed value of P- It follows from (5) that appeared cavitation bubble grows indefinitely at Rb > Rcr, and it collapses when Rb < Rcr Cavitation Bubble Dynamics and Work Estimation The first term on the right-hand side of (11) corresponds to the time dependence of the pressure of the acoustic wave, the second to the surface tension forces with the assumed "Lorentzian" dependence of the surface tension coefficient on the bubble radius (3) In this case, we neglect the second term on the right-hand side of (11) From (7) follows the estimate for the number of the cavitation pores that appeared in the unit of volume The estimate (9) is a more accurate estimate of the total number of bubbles has the form

9: The power emitted per unit surface of the piezoelectric plate to maintain bubble saturation density in the near-wall region  (W/m2) can be estimated by knowing the energy density in a sound wave Ws in the vicinity of the oscillating wall We have shown that ultrasound generated by oscillating piezoelectric plates placed on a surface bounded by a liquid flow can be a source of cavitation in the boundary layer In turn, following the works

1-3: , it can be expected that the emerging cavitation vapor bubbles will lead to a significant decrease in the coefficient of friction Future experimental studies and further development of the theory will make possible to apply this approach practical applications Page 9 --- The estimate (20) is an upper limit, since we neglect the change in the mechanical properties of the liquid due to a large number of bubbles rising The present work is of a qualitative, evaluative nature and does not claim to describe accurately the processes of cavitation bubble expansion, fusion and motion induced in a liquid by the oscillations of the plate with the pressure amplitude P0 > Pcr We have shown that ultrasound generated by oscillating piezoelectric plates placed on a surface bounded by a liquid flow can be a source of cavitation in the boundary layer In turn, following the works

1-3: , it can be expected that the emerging cavitation vapor bubbles will lead to a significant decrease in the coefficient of friction Future experimental studies and further development of the theory will make possible to apply this approach practical applications Page 8 --- The estimate (20) is an upper limit, since we neglect the change in the mechanical properties of the liquid due to a large number of bubbles rising The present work is of a qualitative, evaluative nature and does not claim to describe accurately the processes of cavitation bubble expansion, fusion and motion induced in a liquid by the oscillations of the plate with the pressure amplitude P0 > Pcr We have shown that ultrasound generated by oscillating piezoelectric plates placed on a surface bounded by a liquid flow can be a source of cavitation in the boundary layer In turn, following the works

1-3: , it can be expected that the emerging cavitation vapor bubbles will lead to a significant decrease in the coefficient of friction Future experimental studies and further development of the theory will make possible to apply this approach practical applications Page 7 --- The estimate (9) is a more accurate estimate of the total number of bubbles has the form

9: The corresponding change in pressure in the liquid is: P = csδρ = Vcrnbcs ρ Page 6 --- The estimate (8) is a more accurate estimate of the total number of bubbles has the form

9: The corresponding change in pressure in the liquid is: P = csδρ = Vcrnbcs ρ Page 5 --- The corresponding change in pressure in the liquid is: P = csδρ = Vcrnbcs ρ Page 4 --- The corresponding change in pressure in the liquid is: P = csδρ = Vcrnbcs ρ Page 3 --- The corresponding change in pressure in the liquid is: P = csδρ = Vcrnbcs ρ Page 2 --- The corresponding amplitudes of the normal velocity and pressure of the liquid on the oscillating boundary are 0 u = ωa and 0 P c a = ρ s Page 1 --- It is known that gas bubbles on the surface bounding a fluid flow can change the coefficient of friction and affect the parameters of the boundary layer In this paper, we propose a method that allows us to create, in the near-wall region, a thin layer of liquid filled with bubbles It will be shown that if there is an oscillating piezoelectric plate on the surface bounding a liquid, then, under certain conditions, cavitation develops in the boundary layer The relationship between the parameters of cavitation and the characteristics of the piezoelectric plate oscillations is obtained Page 9 --- The estimate (8) is a more accurate estimate of the total number of bubbles has the form

9: The corresponding change in pressure in the liquid is: P = csδρ = Vcrnbcs ρ Page 8 --- The estimate (9) is a more accurate estimate of the total number of bubbles has the form

9: The corresponding change in pressure in the liquid is: P = csδρ = Vcrnbcs ρ Page 7 --- The estimate (8) is a more accurate estimate of the total number of bubbles has the form

9: The corresponding change in pressure in the liquid is: P = csδρ = Vcrnbcs ρ

Title and authors: Kai: So, we're looking at this paper, "Cavitation near the oscillating piezoelectric plate in water." It sounds like they are proposing a way to use ultrasonic vibrations from a plate attached to a wall to create a thin layer of liquid filled with bubbles right next to that wall.

Mira: Exactly. The main idea here is showing that if you have these specific conditions, cavitation can develop right in the boundary layer near the surface where the plate is vibrating, and they are finding the relationship between those cavitation parameters and how much the piezoelectric plate is oscillating.

Lev: It sounds like a mechanism for generating liquid filled with bubbles using ultrasonic vibrations from a piezoelectric plate on a surface, which seems to be what we need to figure out how to model for real hardware.

Kai: Right. The paper sets up the physics by considering transverse vibrations of an immersed flat plate in water and describing the resulting perturbations in density, pressure, and fluid velocity according to equation one.

Mira: And they are using that setup to show that when the plate vibrates harmonically, like a sine wave at frequency omega t, you get these oscillations in density perturbation and pressure perturbation that depend on cosine of omega t minus k x.

Lev: That cosine dependence means the pressure field oscillates with space and time, which is key because cavitation happens in areas of negative pressure.

Kai: So, they move on to the nucleation mechanism, showing how cavitation can occur in these rarefaction regions of a sound wave using an expression for the nucleation rate.

Mira: They assume a "Lorentzian" dependence for the surface tension coefficient on the bubble radius, and from that they find a critical bubble radius, Rcr, where the energy of bubble formation reaches a maximum at a fixed negative pressure.

Lev: So they're saying that if the bubble radius is larger than this critical radius Rcr, it will grow indefinitely until it collapses when it gets smaller than Rcr.

Kai: And they estimate the total number of cavitation pores that appear in a unit volume, which is given by equation nine, and they also have a more accurate estimate for the total number of bubbles.

Mira: That accuracy comes from considering how the surface tension coefficient depends on the bubble radius, and they find that this gives us an estimate for the power emitted per unit surface of that piezoelectric plate needed to maintain a certain bubble saturation density in that near-wall region.

Lev: It’s interesting to see them linking the acoustic wave energy density in the vicinity of the oscillating wall to this power estimate, which suggests how much input energy is required.

Kai: So, they conclude by saying that ultrasound generated by these oscillating piezoelectric plates can indeed be a source of cavitation in the boundary layer, and they expect these emerging vapor bubbles to lead to a significant decrease in the coefficient of friction.

Mira: They stress that this is an estimate based on certain assumptions, and they also point out their limitation: the estimate for power per unit surface is an upper limit because they neglect how the mechanical properties of the liquid change when there's a large number of bubbles rising.

Lev: That’s a fair caveat. The paper admits it’s more qualitative, evaluative work regarding bubble expansion and motion, not a detailed description of those processes when the pressure amplitude is greater than Pcr.

Kai: So, the big implication for me as someone who works with hardware is that this gives us a way to design these plates and their vibrations to intentionally induce cavitation near surfaces.

Mira: And for theory, it connects the plate's oscillation characteristics directly to the resulting cavitation phenomena in a fluid flow.

Lev: For real hardware, it tells us what kind of energy density you need and what those estimates actually look like when you try to run them on a system that can handle that level of complexity.

Kai: Well, looking at the findings from this paper, we see it’s a solid starting point for exploring active flow control methods using acoustic sources.

Mira: It really lays out the pathway: vibrate the plate, get negative pressure waves, and if those waves are intense enough, you get cavitation bubbles that reduce friction.

Lev: It means if we can model the power estimate they give us accurately, we might be able to design a system that achieves drag reduction without needing massive amounts of energy input.

Kai: So the next step is definitely experimental validation to see if we can actually build this setup and measure those friction coefficient changes.

Mira: And theoretically, they need to refine those assumptions about surface tension dependence and saturation effects for a more precise model.

Lev: I think the focus moving forward should be on how much computational overhead it takes to simulate the dynamics of these growing and collapsing bubbles accurately in a real fluid environment.

Kai: So that’s where we head next, looking at how these concepts fit into the larger picture of fluid-structure interaction.

The paper's summary: Kai: So, this paper is basically saying that if you stick an oscillating piezoelectric plate into water, it can actually create these tiny bubbles right in the layer of fluid right against that plate’s surface.

Mira: Exactly, and it’s not just some random noise; they show that under certain conditions—when the vibrations hit a specific frequency—that negative pressure region gets strong enough to start cavitation.

Lev: So what they actually do is take those ultrasonic vibrations from the plate, which creates a pressure wave in the water right near it.

Kai: Right, and that pressure wave drops below a certain level, causing bubbles to form. It’s like making a small vacuum bubble where there was just liquid.

Mira: And they model how these bubbles grow because of surface tension. They find a critical radius where the bubble stops growing and starts collapsing.

Lev: From an engineering standpoint, it means we can predict how many of these tiny pores will appear in a certain volume based on the plate’s vibration strength.

Kai: And they put a real limit on that, showing that to keep this bubbling happening all over the wall surface, you need a certain amount of power emitted by that piezoelectric plate.

Mira: They say this power estimate is an upper limit because it doesn't account for how the liquid itself changes when you have thousands of these bubbles floating around.

Lev: That’s a key caveat, right? It means the number they get is a theoretical maximum, not necessarily what you’ll see in a real test setup with high bubble densities.

Kai: But the big implication is that if you can control those plate vibrations precisely, these vapor bubbles could actually reduce friction in fluid flows.

Mira: That’s what they're pointing toward—using this controlled cavitation to thin out the boundary layer and cut drag.

Lev: So, the next step for us is figuring out how much real-world power you need to put into that plate to make these bubbles actually do that drag reduction effect.

The paper's improvements: Kai: So, the authors look at where their model falls short and suggest some ways to make it more accurate for real work.

Mira: They point out that their original power estimate is an upper limit because they ignored how the liquid’s mechanical properties change when you have a huge number of bubbles rising.

Lev: That makes sense, right? If you have a lot of bubbles, the whole water system changes, and your simple estimate won't hold up anymore.

Kai: Exactly. They suggest that if we can incorporate those changes into the model, we get a more realistic look at how many bubbles actually form.

Mira: And they propose using an AI system to predict those bubble nucleation rates by including parameters from equation two, which links the rate to that negative pressure and the bubble volume through some complex exponential relationship with Boltzmann and Planck constants.

Lev: That sounds like a lot of computational work, but if it gets us closer to reality on how fast those bubbles appear under specific sound wave conditions, it’s worth the overhead.

Kai: They also suggest modeling the total number of cavitation pores using equation nine in a way that accounts for saturation effects over time, which gives a better prediction than models that just assume there are infinite bubbles.

Mira: Plus, they have an idea to use AI to calculate the characteristic time it takes for pressure to equilibrate, which depends on the oscillation frequency and that critical radius we talked about earlier.

Lev: Knowing that timing helps when you’re trying to design a system where you need that negative pressure region to become significant enough for bubble generation, so that’s a practical gain.

Kai: Then they suggest using AI to estimate the work done by the negative pressure creating those bubbles in a unit volume, which gives us a quantitative measure of the energy available under different sound wave amplitudes.

Mira: And finally, they propose an AI system to calculate the power emitted per unit surface needed to maintain that saturation density, which is what we need for optimizing that piezoelectric plate design.

Lev: That final estimate sounds like something we could actually use to tune a physical prototype and see if we get the desired drag reduction effect on a real setup.

Kai: So, they’re essentially pushing the work toward using AI to move from a simple theoretical estimate to something that can actually guide hardware design.

Conclusion: Kai: So, to wrap up this talk on "Cavitation near the oscillating piezoelectric plate in water," we’ve seen that using ultrasonic vibrations from a plate attached to a surface can indeed create bubbles in the liquid right next to it.

Mira: It shows that if you get the pressure right, those vapor bubbles can form and potentially cut down on friction in fluid flows, which is what they're hoping for.

Lev: From my side, I just see this as a solid theoretical starting point showing the mechanism, but we still need to figure out how much real-world power you actually need to pump into that plate to make it work reliably.

Kai: Right, and their suggestion to use AI tools for predicting bubble nucleation rates and saturation effects is what makes this paper really interesting for us working with actual hardware.

Mira: It moves the discussion past just a simple equation and toward a system where you can actually design the plate parameters to get the desired drag reduction effect.

Lev: I agree, that shift from a static estimate to an AI-guided optimization is what makes this relevant for error correction in real systems, because we need those models to run on actual hardware.

Kai: So, the main implication is that this approach opens up a new way to actively control fluid boundaries using ultrasonic energy sources.

Mira: It’s a proof of concept showing that acoustic energy can be targeted to create nanoscale features in liquids near solid surfaces, which is something we need to keep exploring.

Lev: We'll definitely look at how these kinds of localized phenomena interact with larger fluid dynamics problems next.

M. N. Shneider, M. Pekker

Department of Mechanical and Aerospace Engineering, Princeton University · The George Washington University

physics.flu-dyn

Submitted: 2017-11-14

Updated: 2026-11-10

License: http://arxiv.org/licenses/nonexclusive-distrib/1.0/

Importance score: 74/100

The gist: Cavitation near the oscillating piezoelectric plate in water proposes a method to create a thin layer of liquid filled with bubbles near a wall using ultrasonic vibrations and shows that cavitation…

Key concepts

Cavitation
Cavitation is the formation and subsequent collapse of gas bubbles in a liquid caused by rapid changes in pressure. In this context, it happens when ultrasonic vibrations create areas of very low (negative) pressure, causing water molecules to vaporize into bubbles.
Piezoelectric Plate Oscillation
A piezoelectric plate is a material that generates an electric charge when subjected to mechanical stress (like vibration), and conversely, it changes shape when an electric field is applied. When this plate vibrates, it generates sound waves in the water, which are the source of the necessary pressure fluctuations for bubble formation.
Boundary Layer
The boundary layer is a thin region of fluid immediately adjacent to a solid surface where viscous effects are significant. The paper focuses on how ultrasonic vibrations from the plate can induce cavitation specifically within this thin layer near the wall, affecting fluid flow properties.

Terminology

Summary

Cavitation near the oscillating piezoelectric plate in water proposes a method to create a thin layer of liquid filled with bubbles near a wall using ultrasonic vibrations and shows that cavitation develops under certain conditions

Introduction to Cavitation Control

It is known that gas bubbles on the surface bounding a fluid flow can change the coefficient of friction and affect the parameters of the boundary layer Such bubbles are intensely formed in the liquid as a result of cavitation in areas of negative pressure In this paper, we propose a method for generating cavitation in the near-wall region We will show that cavitation can be generated in the boundary layer near the wall by performing ultrasonic vibrations Such oscillations can be excited, for example, by a piezoelectric plate glued to the wall bounding a liquid

Vibrations and Sound Wave Generation

Consider generation of sound in water caused by transverse vibrations of an immersed flat plate In the linear approximation without damping, equations describing the oscillations of a liquid can be written in the form [4] Assuming the plate vibrations to be harmonic a(t) = a sin(ωt) = 0, from the no-slip condition it follows from (1) that ρ',P',u' ∝ cos(ωt - kx), where s k = ω / c The corresponding amplitudes of the normal velocity and pressure of the liquid on the oscillating boundary are 0 u = ωa and 0 P c a = ρ s

Bubble Nucleation Mechanism

It is known that cavitation can occur in the rarefaction regions of a sound wave An expression for the nucleation rate in the negative pressure region is as follows [9] Assuming the Lorentzian dependence of the surface tension coefficient σ on the bubble radius Rb [9] From (5) we find the value of the bubble radius Rcr at which Wb reaches a maximum at fixed value of P- It follows from (5) that appeared cavitation bubble grows indefinitely at Rb > Rcr, and it collapses when Rb < Rcr

Cavitation Bubble Dynamics and Work Estimation

The first term on the right-hand side of (11) corresponds to the time dependence of the pressure of the acoustic wave, the second to the surface tension forces with the assumed Lorentzian dependence of the surface tension coefficient on the bubble radius (3) In this case, we neglect the second term on the right-hand side of (11) From (7) follows the estimate for the number of the cavitation pores that appeared in the unit of volume The estimate (9) is a more accurate estimate of the total number of bubbles has the form [9] The power emitted per unit surface of the piezoelectric plate to maintain bubble saturation density in the near-wall region  (W/m2) can be estimated by knowing the energy density in a sound wave Ws in the vicinity of the oscillating wall

Conclusion and Application Potential

We have shown that ultrasound generated by oscillating piezoelectric plates placed on a surface bounded by a liquid flow can be a source of cavitation in the boundary layer In turn, following the works [1-3], it can be expected that the emerging cavitation vapor bubbles will lead to a significant decrease in the coefficient of friction Future experimental studies and further development of the theory will make possible to apply this approach practical applications

--- Page 9 ---

The estimate (20) is an upper limit, since we neglect the change in the mechanical properties of the liquid due to a large number of bubbles rising The present work is of a qualitative, evaluative nature and does not claim to describe accurately the processes of cavitation bubble expansion, fusion and motion induced in a liquid by the oscillations of the plate with the pressure amplitude P0 > Pcr We have shown that ultrasound generated by oscillating piezoelectric plates placed on a surface bounded by a liquid flow can be a source of cavitation in the boundary layer In turn, following the works [1-3], it can be expected that the emerging cavitation vapor bubbles will lead to a significant decrease in the coefficient of friction Future experimental studies and further development of the theory will make possible to apply this approach practical applications

--- Page 8 ---

The estimate (20) is an upper limit, since we neglect the change in the mechanical properties of the liquid due to a large number of bubbles rising The present work is of a qualitative, evaluative nature and does not claim to describe accurately the processes of cavitation bubble expansion, fusion and motion induced in a liquid by the oscillations of the plate with the pressure amplitude P0 > Pcr We have shown that ultrasound generated by oscillating piezoelectric plates placed on a surface bounded by a liquid flow can be a source of cavitation in the boundary layer In turn, following the works [1-3], it can be expected that the emerging cavitation vapor bubbles will lead to a significant decrease in the coefficient of friction Future experimental studies and further development of the theory will make possible to apply this approach practical applications

--- Page 7 ---

The estimate (9) is a more accurate estimate of the total number of bubbles has the form [9] The corresponding change in pressure in the liquid is: P = csδρ = Vcrnbcs ρ

--- Page 6 ---

The estimate (8) is a more accurate estimate of the total number of bubbles has the form [9] The corresponding change in pressure in the liquid is: P = csδρ = Vcrnbcs ρ

--- Page 5 ---

The corresponding change in pressure in the liquid is: P = csδρ = Vcrnbcs ρ

--- Page 4 ---

The corresponding change in pressure in the liquid is: P = csδρ = Vcrnbcs ρ

--- Page 3 ---

The corresponding change in pressure in the liquid is: P = csδρ = Vcrnbcs ρ

--- Page 2 ---

The corresponding amplitudes of the normal velocity and pressure of the liquid on the oscillating boundary are 0 u = ωa and 0 P c a = ρ s

--- Page 1 ---

It is known that gas bubbles on the surface bounding a fluid flow can change the coefficient of friction and affect the parameters of the boundary layer In this paper, we propose a method that allows us to create, in the near-wall region, a thin layer of liquid filled with bubbles It will be shown that if there is an oscillating piezoelectric plate on the surface bounding a liquid, then, under certain conditions, cavitation develops in the boundary layer The relationship between the parameters of cavitation and the characteristics of the piezoelectric plate oscillations is obtained

--- Page 9 ---

The estimate (8) is a more accurate estimate of the total number of bubbles has the form [9] The corresponding change in pressure in the liquid is: P = csδρ = Vcrnbcs ρ

--- Page 8 ---

The estimate (9) is a more accurate estimate of the total number of bubbles has the form [9] The corresponding change in pressure in the liquid is: P = csδρ = Vcrnbcs ρ

--- Page 7 ---

The estimate (8) is a more accurate estimate of the total number of bubbles has the form [9] The corresponding change in pressure in the liquid is: P = csδρ = Vcrnbcs ρ

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved AI systems can predict cavitation bubble nucleation rates by incorporating parameters from equation (2), which relates nucleation rate to negative pressure and bubble volume through a complex exponential relationship involving Boltzmann and Planck constants. This allows for more accurate estimation of when cavitation microbubbles will appear under specific acoustic conditions.

  2. The system can model the time evolution of nanopore number density using equation (9) to account for saturation effects, providing a more realistic prediction of bubble formation over time than models without saturation, as shown by comparing curves in Figure 2.

  3. AI systems can calculate the characteristic time of pressure equilibration using equation (10), which depends on oscillation frequency and critical radius, enabling precise timing for when the negative pressure region becomes significant enough for bubble generation.

  4. The system can estimate the work done by negative pressure creating bubbles in a unit volume using equation (14), providing a quantitative measure of the energy available for cavitation processes under various sound wave amplitudes.

  5. AI systems can calculate the power emitted per unit surface of the piezoelectric plate to maintain bubble saturation density using equation (20), allowing for design optimization of piezoelectric plate frequencies and amplitudes to achieve desired drag reduction effects.

Related papers