Explicit dispersion relations for elastic waves in extremely deformed soft matter with application to nearly incompressible and auxetic materials
Listen
Radio episode about this paper
Transcript
Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.
Kai: I'm Kai.
Mira: And I'm Mira, here with Lev.
Kai: We're looking at the paper: "Explicit dispersion relations for elastic waves in extremely deformed soft matter with application to nearly incompressible and auxetic materials".
Mira: Here's the gist of the paper. Explicit dispersion relations for elastic waves in extremely deformed soft matter with application to nearly incompressible and auxetic materials is derived by means of superimposed on large deformations Bloch wave analysis frequently used for investigation of elastic wave propagation The availability of the explicit dispersion relations is important for designing mechanotunable acoustic metamaterials Moreover, the information may greatly benefit non-invasive medical diagnostic techniques by providing the important information on dependence of elastic wave propagation on prestress/pre-strain conditions, which is a common state of biological tissues By application of the derived explicit expressions, we show the role of deformation in wave propagation in soft media undergoing finite deformations Moreover, we extent the analysis to a class of exotic metamaterials characterize by negative Poisson’s ratio (NPR) behaviour Analysis of Material Response The study analyzes the propagation of elastic waves in soft materials subjected to finite deformations.
Kai: For nearly incompressible materials, transverse wave velocities exhibit strong dependence on direction of propagation and initial strain state whereas the longitudinal component is not affected significantly until extreme levels of deformations are attained.
Mira: For highly compressible materials, both pressure and shear wave velocities depend strongly on initial deformation and direction of propagation.
Kai: When compression is applied, longitudinal wave velocity decreases in positive bulk modulus materials, and increases for negative bulk modulus materials; this is regardless the direction of wave prorogation.
Paper summary: Kai: So we started by looking at how wave propagation changes when you subject these soft materials to finite deformations. The core idea here is deriving explicit dispersion relations using superimposed Bloch wave analysis for large deformations <ref:1501.00134#pg1>.
Mira: The paper then applies these derived relations to two key areas: nearly incompressible materials, like biological tissues and polymers, and negative Poisson’s ratio or auxetic materials <ref:1501.00134#pg2>.
Lev: So the main claim is that for these systems, the transverse wave velocities are strongly dependent on direction of propagation and initial strain state <ref:1501.00134#pg3>.
Kai: And for highly compressible materials, both pressure and shear wave velocities depend strongly on both initial deformation and direction of propagation <ref:1501.00134#pg2>. When compression is applied, the longitudinal wave velocity changes depending on the material's bulk modulus <ref:1501.00134#pg2>.
Mira: The methodology involves introducing the deformation gradient F of X and t, and using an approximation of the Arruda-Boyce model, specifically the Gent model for stiffening effects <ref:1501.00134#pg2>.
Lev: The Gent model is used because it neatly covers how polymer chains or collagen fibers get stiffer as deformation increases, and it shows that at a certain level of deformation, the energy function becomes unbounded <ref:1501.00134#pg2>.
Kai: When they look at a finitely deformed neo-Hookean material, they find an acoustic tensor Q of n equals a one n tensor n plus two(I minus n tensor n) with specific definitions for the components a one and a two <ref:1501.00134#pg2>.
Mira: This leads directly to the phase velocities for the pressure wave cpw equals p a one over rho and shear wave velocity csw equals p a two over rho, which simplify to known relations in small deformation limits <ref:1501.00134#pg2>.
Lev: So we see that even when things simplify back to known forms, the underlying structure of the finite deformation still dictates the behavior through those a one and a two terms <ref:1501.00134#pg2>.
Kai: They then show how these relations apply differently depending on whether you're dealing with nearly incompressible or highly compressible materials <ref:1501.00134#pg3>.
Mira: And specifically, for auxetic materials with negative Poisson’s ratio, they observe that the pressure wave velocity increases in any direction of propagation n when the material undergoes compression <ref:1501.00134#pg3>.
Lev: That specific directional effect on the pressure wave is a key result we need to consider if we are building hardware for auxetic phononic crystals <ref:1501.00134#pg3>.
Conclusion: Kai: So wrapping up this paper, the authors derived explicit dispersion relations for finitely deformed materials <ref:1501.00134#pg2>. They showed that deformation has a significant role in wave propagation in both nearly incompressible and extreme auxetic materials <ref:1501.00134#pg2>.
Mira: The implication is that these explicit relations can guide the design of mechanotunable acoustic metamaterials and phononic crystals with a wide range of constituent properties <ref:1501.00134#pg2>.
Lev: So for real hardware, it means we can engineer regions with extreme variations in local phononic properties to create various acoustic effects <ref:1501.00134#pg2>.
Kai: The authors focused on showing that the local distribution of strain field in these engineered materials can induce those extreme variations of local phononic properties <ref:1501.00134#pg2>.
Mira: It's about using the
Pavel Galich, Stephan Rudykh
Faculty of Aerospace Engineering, Technion - Israel Institute of Technology
cond-mat.soft
Submitted: 2014-12-31
Updated: 2014-12-31
Comments: 6 figures
DOI: 10.1016/j.eml.2015.06.003
License: http://arxiv.org/licenses/nonexclusive-distrib/1.0/
Importance score: 91/100
The gist: Explicit dispersion relations for elastic waves in extremely deformed soft matter with application to nearly incompressible and auxetic materials is derived by means of superimposed on large…
Key concepts
- Finite Deformations
- This describes analyzing material behavior when it is stretched or compressed beyond small, linear limits. The analysis uses a deformation gradient to model the change in shape over time, capturing non-linear effects like chain stiffening or fiber straightening that occur in soft materials.
- Auxetic Materials
- These are exotic materials characterized by a negative Poisson's ratio, meaning they get thicker when stretched instead of thinner. The paper examines their unique wave propagation behavior, showing how their negative bulk modulus affects pressure and shear wave velocities differently than conventional materials.
- Dispersion Relations
- These are mathematical equations that relate the frequency of a wave to its wavelength and the material's properties. The paper derives these explicit relations for deformed materials, allowing engineers to predict exactly how waves will travel through these complex structures.
- Strain-Energy Density Function (Gent Model)
- This is a mathematical model used to describe how energy stored in a material changes when it is deformed. The Gent model specifically accounts for the stiffening effects in polymers or biological tissues, showing that as deformation increases, the material becomes much stiffer.
Terminology
Summary
Explicit dispersion relations for elastic waves in extremely deformed soft matter with application to nearly incompressible and auxetic materials is derived by means of superimposed on large deformations Bloch wave analysis frequently used for investigation of elastic wave propagation The availability of the explicit dispersion relations is important for designing mechanotunable acoustic metamaterials Moreover, the information may greatly benefit non-invasive medical diagnostic techniques by providing the important information on dependence of elastic wave propagation on prestress/pre-strain conditions, which is a common state of biological tissues By application of the derived explicit expressions, we show the role of deformation in wave propagation in soft media undergoing finite deformations Moreover, we extent the analysis to a class of exotic metamaterials characterize by negative Poisson’s ratio (NPR) behaviour
Analysis of Material Response
The study analyzes the propagation of elastic waves in soft materials subjected to finite deformations. For nearly incompressible materials, transverse wave velocities exhibit strong dependence on direction of propagation and initial strain state whereas the longitudinal component is not affected significantly until extreme levels of deformations are attained. p. 0 For highly compressible materials, both pressure and shear wave velocities depend strongly on initial deformation and direction of propagation. p. 0 When compression is applied, longitudinal wave velocity decreases in positive bulk modulus materials, and increases for negative bulk modulus materials; this is regardless the direction of wave prorogation. p. 0 The authors demonstrate that finite deformations influence elastic wave propagation through combinations of induced effective compressibility and stiffness. p. 0 p. 0
Modeling Finite Deformations
To analyze the finitely deformed state, the deformation gradient F(X, t) = ∇X ⊗ x(X, t) is introduced. To account for finite deformation non-linear effects as well as material nonlinearity, the wave propagation is analyzed in terms of infinitesimal plane waves superimposed on a finitely deformed state. p. 0 To account for the stiffening effects due to finite extensibility of polymer chains or collective straightening of collagen fibers in biological tissues, the strain-energy density function corresponding to an approximation of Arruda-Boyce model, namely the Gent model, is used. p. 0 This model neatly covers the stiffening of the material with deformation; as the deformation attends the level of I1 = 3 +Jm, the energy function becomes unbounded and a dramatic increase in stress occurs. p. 0 Clearly, when Jm → ∞, the strain-energy function reduces to the neo-Hookean one. p. 0
Dispersion Relations and Wave Types
The acoustic tensor for a finitely deformed neo-Hookean material takes the form Q(n) = a1n ⊗ n + a2(I − n ⊗ n). Consequently, there always exist one longitudinal (pressure) and two transverse (shear) waves for any direction of propagation n. p. 1 p. 1 Phase velocities of these waves can be calculated as cpw = p a1/ρ and csw = p a2/ρ. p. 1 p. 1 In the limit of small deformations the results reduce to the well known relations cpw = p (K + 4µ/3)/ρ and csw = µ/ρ. p. 1 p. 1
Application to Specific Material Classes
For nearly incompressible materials (K/µ 1 and λ˜ 'λ-1/2), the dependence of the pressure wave velocity on the direction of propagation and initial stress state is relatively weak. However, the velocities of shear waves depend strongly on the direction of propagation and the deformation state. p. 1 In contrast to nearly incompressible materials, for highly compressible matter, the velocity of pressure wave depends strongly on the direction of propagation and initial stress state. p. 1 Remarkably, if K/µ varies in the vicinity of 2/3 which corresponds to Poisson’s ratio ν in the vicinity of 0, then the velocities of pressure and shear waves are not influenced by the initial stress-strain state. p. 1
Auxetic Material Behavior
The analysis extends to auxetic materials with negative bulk modulus, examining material behavior when −1/3 < K/µ < 0. An example for an auxetic material with K/µ = −0. p. 13 is shown in FIG. p. 1 3 for pressure (a) and shear phase velocities (b). p. 1 We observe that the velocity of the pressure wave increases in any direction of propagation n when the material undergoes compression. p. 1 Moreover, the velocity of the pressure wave increases significantly and has maximum when wave vector n lies in the plane orthogonal to the axis of compression. p. 1 Secondly, velocities of shear waves (FIG. p. 1 3 (b)) decrease considerably for all directions of propagations n in contrast to the effect of deformation observed in nearly incompressible materials. p. 1
Conclusion and Outlook
The authors derived the explicit dispersion relations for finitely deformed materials and demonstrated the significant role of deformation on elastic wave propagation on examples of both nearly incompressible and extreme auxetic materials. These findings may guide further design of mechanotunable acoustic metamaterials and phononic crystals with a large range of constituent properties. p. 3 p. 3 The local distribution of strain field in these engineered materials can be used to induce regions with extreme variation of the local phononic properties to give rise to various acoustic effects. p. 3 p. 3
References
The references cited are M. Biot, “The influence of initial stress on elastic waves,” J. p. 3 Appl. Phys. 11, 522 (1940), C. p. 3 Truesdell and W. p. 3 Noll, The Non-Linear Field Theories of Mechanics, 3rd ed. p. 3, edited by S. p. 3 S. Antman (Springer, 1965), A. p. 3 Norris, “Propagation of plane waves in a pre-stressed elastic medium,” J. p. 3 Acoust. Soc. Am 74, 1642 (1983), R. p. 3 Ogden, Non-Linear elastic deformations (Dover Publications, 1984), M. p. 3 S. Kushwaha, P. p. 3 Halevi, L. Dobrzynski, and B. p. 3 DjafariRouhani, “Acoustic band structure of periodic elastic composites,” Phys. p. 3 Rev. Lett. 71, 2022 (1993), V. p. 3 K. Ignatovich and L. p. 3 T. N. Phan, “Those wonderful elastic waves,” Am. p. 3 J. Phys. 77, 1162 (2009), R. p. 3 Ogden and B. p. 3 Sighn, “Propagation of waves in an incompressible transversally isotripic elastic solid with initial stress: Biot revisited,” Journal of Mechanics of Materials and Structures 6, 453–477 (2011), M. p. 3 Shams, M. Destrade, and R. p. 3 Ogden, “Initial stresses in elastic solids: Constitutive laws and acoustoelasticity,” Wave Motion 48, 552–567 (2011), W. p. 3 Parnell, A. p. 3 N. Norris, and T. p. 3 Shearer, “Employing pre-stress to generate finite cloaks for antiplane elastic waves,” Appl. p. 3 Phys. Lett. 100, 171907 (2012), K. p. 3 E. Evans and K. p. 3 L. Alderson, “Auxetic materials: the positive side of being negative,” Engineering Science and Education Journal 9, 148–154 (2000), B. p. 3 D. Caddock and K. p. 3 E. Evans, “Negative poissons ratios and strain-dependent mechanical properties in arterial prostheses,” Biomaterials 16, 1109–1115 (1995), S. p. 3 Babaee, J. Shim, J. Weaver, E. Chen, N. Patel, and K. p. 3 Bertoldi, “3d soft metamaterials with negative poissons ratio,” Adv. p. 3 Mater. 25, 5044–5049 (2013), Y. p. 3 Wang and R. p. 1 Lakes, “Composites with inclusions of negative bulk modulus: Extreme damping and negative poissons ratio,” Journal of Composite Materials 39, 1645–1657 (2005), N. p. 4 Gaspar, C. W. Smith, and K. p. 4 E. Evans, “Effect of heterogeneity on the elastic properties of auxetic materials,” J. p. 4 Appl Phys 94, 6143 (2003), L. p. 4 Chen, C. Liu, J. Wang, W. Zhang, C. Hu, and S. Fan, “Auxetic materials with large negative poissons ratios based on highly oriented carbon nanotube structures,” Appl Phys Lett 94, 253111 (2009), K. p. 4 Bertoldi, P. p. 3 Reis, S. Willshaw, and T. p. 4 Mullin, “Negative poissons ratio behavior induced by an elastic instability,” Adv. p. 4 Mater 22, 361–366 (2010), T. p. 4 Still, M. Oudich, G. K. Auerhammer, D. p. 4 Vlassopoulos, B. p. 4 Djafari-Rouhani, G. p. 4 Fytas, and P. p. 4 Sheng, “Soft silicone rubber in phononic structures: Correct elastic moduli,” Phys Rev B 88, 094102 (2013), P. p. 4 J. Beltramo, D. p. 4 Schneider, G. p. 4 Fytas, and E. p. 4 M. Furst, “Anisotropic hypersonic phonon propagation in films of aligned ellipsoids,” Phys Rev Lett 113, 205503 (2014). p. 4
--- Page 6 ---
The acoustic tensor takes the form Q(n) = a1n ⊗ n + a2(I − n ⊗ n), (3) where the unit vector n defines the direction of propagation of the wave; n ⊗ n is the projection on the direction n; (I − n ⊗ n) is the projection on the plane normal to n. a1 = (K − 2µ/3)J + µJ−1 (1 + n· B ·n) and a2 = µJ−1 (n·B·n). p. 1 Consequently, there always exist one longitudinal (pressure) and two transverse (shear) waves for any direction of propagation n. Phase velocities of these waves can be calculated as cpw = p a1/ρ and csw = p a2/ρ. In the limit of small deformations the results reduce to the well known relations cpw = p (K + 4µ/3)/ρ and csw = µ/ρ.
Wave Velocity Dependence
For nearly incompressible materials, the dependence of the pressure wave velocity on the direction of propagation and initial stress state is relatively weak. However, the velocities of shear waves depend strongly on the direction of propagation and the deformation state (FIG. p. 1 1). In particular, we observe prominent minima and maxima of the velocities when waves propagate along the principal directions. p. 1 In contrast to nearly incompressible materials, for highly compressible matter, the velocity of pressure wave depends strongly on the direction of propagation and initial stress state (see FIG. p. 1 2 (a)). More specifically the velocity of pressure wave increases when material is stretched and decreases when it is compressed. p. 1
Stiffening Effects in Deformed Media
When compression is applied, longitudinal wave velocity decreases in positive bulk modulus materials, and increases for negative bulk modulus materials; this is regardless the direction of wave prorogation. The authors demonstrate that finite deformations influence elastic wave propagation through combinations of induced effective compressibility and stiffness. In the Gent material model, if wave vector n lies in one of the planes of orthotropy then we always have one pure transverse (shear) wave with the velocity csw = p a2Jm/(ρξ). p. 2 For waves propagating along principal directions in Gent material, we have only pure modes. p. 2 At these extreme deformations, the stiffening effect manifests in a significant increase o the effective shear modulus, which becomes comparable with the bulk modulus. p. 3
Summary of Findings
The explicit dispersion relations for finitely deformed materials and demonstrated the significant role of deformation on elastic wave propagation on examples of both nearly incompressible and extreme auxetic materials. These findings may guide further design of mechanotunable acoustic metamaterials and phononic crystals with a large range of constituent properties. The local distribution of strain field in these engineered materials can be used to induce regions with extreme variation of the local phononic properties to give rise to various acoustic effects.
Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.
Improvements for AI systems
-
Enhanced modeling of soft matter wave propagation allows AI systems to design mechanotunable acoustic metamaterials by explicitly designing dispersion relations for finitely deformed materials, as derived in equations (7) and (8).
-
Improved material characterization enables AI systems to predict the local distribution of strain field in engineered materials, allowing them to induce regions with extreme variation of local phononic properties for various acoustic effects.
-
The explicit dependence of wave velocities on initial stress state and direction allows AI systems to provide non-invasive medical diagnostic techniques by incorporating prestress/pre-strain conditions common in biological tissues.
-
AI systems can analyze the stiffening effects described by the Gent material model, enabling them to predict dramatic changes in longitudinal wave velocity when extreme deformations are attained, as shown in FIG 5.
-
The derived explicit dispersion relations can be used by AI systems to design phononic crystals and acoustic metamaterials with a large range of constituent properties, leveraging the findings for tunable acoustic/phononic metamaterials.
Related papers
- Coarse-graining dense, deformable active particles
- Three-body corrections to the Brownian viscosity of hard spheres without hydrodynamic interactions
- Thin active nematohydrodynamic layers: asymptotic theories and instabilities
- Origins of suppressed self-diffusion of nanoscale constituents of a complex liquid
- Soft material mechanical property degradation at high strain rates
- Avalanche criticality emerges by thermal fluctuation in a quiescent glass