How do sub-bandgap reflectors affect the performance of photovoltaic modules?

summary

The gist

Sub-bandgap reflectors (SBR) can reduce the temperature of photovoltaic (PV) modules by reflecting the near-infrared region of the solar spectrum with photon energies smaller than the electronic…

In short

Sub-bandgap reflectors (SBRs) reflect near-infrared light to reduce PV module temperature, potentially increasing annual energy yield by 1.0% to 2.4%. While instantaneous efficiency doesn't improve much, SBRs can extend module lifetime by reducing degradation over 30 years. Non-ideal reflectors show losses that can negate the yield gain.

Key concepts

Sub-bandgap Reflector (SBR)
An SBR reflects near-infrared solar light whose energy is less than the cell's electronic bandgap. This reflection keeps the module cooler, which helps slow down physical degradation over time, even if it slightly reduces immediate power output.
Annual Energy Yield (AEY)
This measures the total energy a PV module produces over a year. An ideal SBR is expected to moderately increase this yield for both open-rack and close-roof mounted modules, depending on the specific mounting configuration.
Degradation Modeling
The paper uses an Arrhenius approach to model how temperature affects PV module degradation. A cooler operating temperature slows down the degradation rate, which can significantly extend the module's operational lifetime over decades.
Non-Ideal SBR Effects
If an SBR is imperfect, it causes losses by partially reflecting light outside the intended bandgap. These losses in current density can counteract any potential energy yield gains, resulting in a net loss for open-rack modules.

Terminology used across episodes

This episode discusses

The paper

How do sub-bandgap reflectors affect the performance of photovoltaic modules? · Read on arXiv

Department Optics for Solar Energy, Helmholtz-Zentrum Berlin für Materialien und Energie GmbH · Computational Nano Optics, Zuse Institute Berlin · Andlinger Center for Energy and the Environment, Princeton University Department of Civil and Environmental Engineering, Princeton University Department of Electrical and Computer Engineering, School of Architecture at Princeton University

Sub-bandgap reflectors (SBR) can reduce the temperature of photovoltaic (PV) modules by reflecting the near-infrared region of the solar spectrum with photon energies smaller than the electronic bandgap of the solar cell absorber material. We consider an ideal SBR, which reflects 100% of non-harvestable low-energy photons but does not alter the reflectivity of the PV module for usable high-energy photons, and estimate how reducing the module temperature with the SBR affects the annual and the cumulative energy yield of silicon PV modules for six locations in North America and Europe. An ideal SBR would increase the annual energy yield between 0.9% and 1.4% for open-rack mounted modules and between 1.5% and 2.3% for close-roof mounted PV modules. Whether a non-ideal SBR provides a benefit in actual deployments strongly depends on the location and the optical properties of the coating. Beyond effects on the instantaneous power conversion efficiency and hence the annual energy yield, reducing the temperature by an SBR might also reduce the degradation and increase the overall lifetime of the PV module. By describing degradation using a simple Arrhenius approach with typical activation energies between 0.4 eV and 0.8 eV, we find that an ideal SBR increases the cumulative energy yield over 30 years between 2.2% and 4.0% for an open-rack mounted PV module in Princeton, New Jersey, USA.

DOI: 10.1039/D6SE00463F

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: We're looking at the paper: "How do sub-bandgap reflectors affect the performance of photovoltaic modules?".

Mira: Here's the gist of the paper. Sub-bandgap reflectors (SBR) can reduce the temperature of photovoltaic (PV) modules by reflecting the near-infrared region of the solar spectrum with photon energies smaller than the electronic bandgap of the solar cell absorber material The ideal SBR would increase the annual energy yield between 1.0% and 1.5% for open-rack mounted modules and between 1.6% and 2.4% for close-roof mounted PV modules Whether a non-ideal SBR provides a benefit in actual deployments strongly depends on the location and the optical properties of the coating Beyond effects on the instantaneous power conversion efficiency and hence the annual energy yield, reducing the temperature by a SBR might also reduce the degradation and increase the overall lifetime of the PV module Impact on Annual Energy Yield The study estimates that an ideal SBR would moderately increase the annual energy yield (AEY) between 1.0% and 1.5% for open-rack mounted modules and between 1.6% and 2.4% for close-roof mounted PV modules.

Kai: This small increase can be rapidly negated in case of a non-ideal SBR with reduced transmissivity in the spectral solar cell absorption regime.

Mira: The results show that even small irradiance losses counterbalance the gain in energy yield leading to a net loss, which is more severe for open-rack mounted modules.

Kai: Effect of Non-Ideal Reflectors When considering non-ideal SBRs, the non-ideality corresponds to a loss in current density.

Title and authors: Kai: So we're looking at this paper called "How do sub-bandgap reflectors affect the performance of photovoltaic modules?" and it’s about using these things to actually cool down solar panels.

Mira: Right, it looks like the authors are proposing that sub-bandgap reflectors, or SBRs, can reduce the temperature of photovoltaic modules by reflecting those near-infrared photons that have energy smaller than the electronic bandgap of the solar cell material.

Lev: From an engineering standpoint, this means we're talking about a passive way to manage heat dissipation right at the surface of the module.

Kai: The paper suggests an ideal SBR could increase the annual energy yield between one point zero percent and one point five percent for open-rack mounted modules and between one point six percent and two point four percent for close-roof mounted PV modules <ref:2604.20757#pg3>.

Mira: That's a pretty modest boost in the annual energy yield, but it depends heavily on whether the reflector is ideal or not, and where you deploy it <ref:2604.20757#pg3>.

Lev: The authors point out that even if you use a non-ideal reflector with less transmissivity in the solar cell absorption regime, those small losses can actually counteract the gain in energy yield, leading to a net loss <ref:2604.20757#pg2>.

Kai: It seems like they're also looking at how this impacts the long-term stability of these modules, beyond just the immediate power conversion efficiency and annual energy yield.

Mira: That’s interesting because reducing the operating temperature might also reduce degradation and increase the overall lifetime of the PV module <ref:2604.20757#pg2>.

Lev: If we look at a simple Arrhenius approach, an ideal SBR could increase the cumulative energy yield over thirty years between two point two percent and four point zero percent for an open-rack mounted PV module in Princeton, New Jersey, USA <ref:2604.20757#pg3>.

Kai: That's a significant potential gain over a three-decade lifespan, especially when you consider the activation energies between zero point four eV and zero point eight eV <ref:2604.20757#pg3>.

Mira: But we have to be careful about those temperature coefficients they use, like beta V being negative zero point four percent per Kelvin and beta J being plus zero point zero zero three percent per Kelvin <ref:2604.20757#pg3>.

Lev: And the paper also looks at how mounting situation matters, showing that for close-roof mounted modules, the annual energy yield with an SBR is always less than the reference yield for open-rack mounted PV modules because the temperature of those close-roof modules is generally higher <ref:2604.20757#pg3>.

Kai: That’s a key detail for deployment—the physical setup dictates whether you see a benefit or not <ref:2604.20757#pg3>.

Mira: And when we look at the spectral data, using the fixed AM1 point 5 spectrum, the overall energy yield is estimated to be slightly lower, which they say is in agreement with a larger average value for spectral data <ref:2604.20757#pg3>.

Lev: They also note that even when spectral data is available, the relative change in energy yield between PV modules with and without an ideal SBR is a bit larger than when spectral data is used <ref:2604.20757#pg3>.

Kai: So, the paper seems to settle on a point about instantaneous efficiency not being significantly affected by the SBR itself, especially for perovskite solar cells where the temperature coefficients are quite small <ref:2604.20757#pg3>.

Mira: True, but they still argue that SBRs might reduce degradation and hence increase the lifetime of PV modules <ref:2604.20757#pg2>.

Lev: So, to summarize the improvements they suggest: one is designing SBRs with production costs that justify those modest expected gains in efficiency and lifetime <ref:2604.20757#pg3>.

Kai: And another big suggestion is that thermal management with SBRs should be investigated in large PV plants and urban environments <ref:2604.20757#pg3>.

Mira: That moves the discussion from just the panel level to a much larger system scale, which is where I see the real potential for this research <ref:2604.20757#pg3>.

Lev: I think for real hardware, we need to figure out how robust these temperature reductions are when you run them under actual operational stress <ref:2604.20757#pg3>.

Kai: So, to wrap up this segment, the paper on "How do sub-bandgap reflectors affect the performance of photovoltaic modules?" shows that while instantaneous efficiency doesn't change much, they could boost annual energy yield by up to two point four percent for close-roof modules and significantly increase the thirty-year cumulative yield by up to four point zero percent for open-rack modules <ref:2604.20757#pg3>.

Mira: The implication is that SBRs might be a worthwhile technology if we can make them cost-effective enough to deploy widely <ref:2604.20757#pg3>.

Lev: We also see the need for better modeling of how degradation rate changes based on temperature reduction, which would give us more concrete numbers for real hardware design <ref:2604.20757#pg3>.

Kai: Next up, we're going to look at how the study handles the practical implementation details and model setup behind these findings.

The paper's summary: Kai: So, we're looking at how these sub-bandgap reflectors, or SBRs, actually work in this paper and what they promise for solar panels <ref:2604.20757#pg1>.

Mira: Basically, the idea is that if you put a reflector on the panel that only reflects light with energy smaller than the silicon bandgap, you cool it down because those photons don't get through to generate electricity <ref:2604.20757#pg1>.

Lev: From an error-correction standpoint, we’re seeing this as a way to manage the temperature fluctuations that really stress the cell material <ref:2604.20757#pg1>.

Kai: The paper then looks at how much better this is for energy output, and it says an ideal reflector could increase the annual energy yield by about one point five percent for open-rack modules and even more for close-roof ones <ref:2604.20757#pg1>.

Mira: But they immediately bring up the catch—that this gain is small, and it's totally dependent on the exact location and the specific coating properties of that reflector <ref:2604.20757#pg1>.

Lev: And then they point out that if you use a non-ideal reflector, where it loses some light for wavelengths shorter than the silicon bandgap, those losses can actually cancel out most of the benefit, leading to a net loss <ref:2604.20757#pg1>.

Kai: So, even with imperfect hardware, the paper suggests that you don't get a guaranteed boost in energy yield just from adding a reflector <ref:2604.20757#pg1>.

Mira: That’s because the instantaneous power conversion efficiency doesn't change much, especially for perovskite cells where their temperature coefficients are very small, between negative zero point four percent per Kelvin and negative zero point one seven percent per Kelvin <ref:2604.20757#pg1>.

Lev: Exactly. So the real value they find is in the long term, when you look at degradation and lifetime extension instead of just a single day's output <ref:2604.20757#pg1>.

Kai: They use an Arrhenius approach to model this, and for an open-rack module in Princeton, New Jersey, they estimate that an ideal SBR could increase the cumulative energy yield over thirty years by between two point two percent and four point zero percent <ref:2604.20757#pg1>.

Mira: That gain depends heavily on the activation energy of the degradation process, which is modeled here as being between zero point four electron volts and zero point eight electron volts <ref:2604.20757#pg1>.

Lev: If we take that lifetime increase seriously, we're talking about a substantial boost to the reliability of these modules over a long period <ref:2604.20757#pg1>.

Kai: The paper also highlights a difference based on mounting type, saying that for close-roof modules, the annual energy yield with an SBR is always less than the reference yield for open-rack ones because those close-roof panels run hotter generally <ref:2604.20757#pg1>.

Mira: That really emphasizes that deployment context matters more than just having a theoretical ideal reflector <ref:2604.20757#pg1>.

Lev: So, the whole point is not that SBRs are a magic fix for efficiency right now, but rather they might be useful for extending module lifetime if we can design them affordably and get them into large plants or urban settings <ref:2604.20757#pg1>.

Kai: Right, so the focus shifts from making the panel more efficient to making it last longer under real-world conditions, which is where my work on thermal management really comes in <ref:2604.20757#pg1>.

The paper's improvements: Tom: So, we're looking at what the authors suggest as improvements they want to see from these sub-bandgap reflectors <ref:2604.20757#pg1>.

Kai: They aren't just happy with the small efficiency gains; they’re pushing for the design and fabrication of these SBRs to have production costs that actually justify those modest expected gains in efficiency and lifetime <ref:2604.20757#pg1>.

Mira: That makes sense, because if it's too expensive, it just sits on a shelf while you wait for the degradation benefits <ref:2604.20757#pg1>.

Lev: I agree, the cost-benefit analysis is crucial for any real deployment of this kind of material science stuff <ref:2604.20757#pg1>.

Kai: And another big thing they suggest is that thermal management with these SBRs should be investigated not just on small panels but in large PV plants and urban environments where heat buildup is really an issue <ref:2604.20757#pg1>.

Mira: It’s a good shift from just looking at the panel as an isolated unit to thinking about how it fits into the whole system architecture <ref:2604.20757#pg1>.

Lev: And they also want better modeling of degradation based on temperature reduction, which means we need more concrete numbers for how much longer a module actually lasts when it’s cooled down <ref:2604.20757#pg1>.

Kai: So, the goal is to move beyond just saying "it might be better" and start designing something that actually performs well and lasts long under operational stress <ref:2604.20757#pg1>.

Mira: It seems like the paper’s main point is that SBRs aren't a magic fix for instantaneous power, but they could be useful for extending module lifetime if we can design them affordably and get them into large plants or urban settings <ref:2604.20757#pg1>.

Lev: Yeah, the implication is that we need to focus our error-correction research on how these temperature changes translate into concrete increases in operational reliability over thirty years <ref:2604.20757#pg1>.

Kai: So, while the efficiency numbers are small, the potential for a longer lifespan under real conditions is what's really driving the next steps for this research <ref:2604.20757#pg1>.

Conclusion: Kai: So we're wrapping up this look at "How do sub-bandgap reflectors affect the performance of photovoltaic modules?" and summarizing what we found <ref:2604.20757#pg1>.

Mira: Basically, the main thing is that while an ideal reflector could add a small boost to annual energy yield, it’s not a big deal for the immediate power output <ref:2604.20757#pg1>.

Lev: That means we're looking at a trade-off between marginal efficiency gain and potentially significant lifetime extension, which is what really matters for real hardware <ref:2604.20757#pg1>.

Kai: Right, so the paper shows that the most interesting part isn't just the energy yield number itself, but how this passive cooling mechanism might help reduce degradation over thirty years <ref:2604.20757#pg1>.

Mira: That longevity boost depends on those activation energies we talked about earlier, between zero point four electron volts and zero point eight electron volts <ref:2604.20757#pg1>.

Lev: If that lifetime extension is real, it means the engineering focus has to shift towards designing these reflectors cheaply enough for widespread use <ref:2604.20757#pg1>.

Kai: So, the conclusion is that SBRs aren't a magic fix for efficiency right now, but they might be useful for extending module lifetime if we can design them affordably and get them into large plants or urban settings <ref:2604.20757#pg1>.

Mira: Exactly, so the real world application is less about maximizing instantaneous power conversion efficiency and more about managing the thermal environment of massive PV arrays <ref:2604.20757#pg1>.

Lev: And we need that better modeling of degradation based on temperature reduction to give us a solid basis for hardware design <ref:2604.20757#pg1>.

Kai: We’re going to keep this paper in mind as we look at how these thermal management techniques integrate with larger energy systems next time <ref:2604.20757#pg1>.

More episodes

← Home