Contact mechanics and friction of soft materials: an apparatus combining multi-axes dynamical actuation/measurement and in situ/in operando visualisation

summary

The gist

Contact mechanics and friction of soft materials: an apparatus combining multi-axes dynamical actuation/measurement and in situ/in operando visualisation introduces an apparatus dedicated to studying…

In short

A new apparatus was developed to study contact mechanics and friction of soft materials by combining multi-axis dynamic actuation with in situ visualization. It allows simultaneous actuation along five degrees of freedom, real-time monitoring of displacements and forces, and optical imaging of the contact interface. This enables a broader range of scientific challenges than existing single instruments.

Key concepts

Multi-axes dynamical actuation
This refers to the apparatus's ability to move a soft sample along five independent directions simultaneously. It uses various stages like piezoelectric translation and goniometers, allowing precise control over motion in x, y, z, and rotation angles (thetaX/thetaY). This high degree of freedom is crucial for complex contact studies.
In situ/in operando visualization
This capability means the apparatus can image the contact interface while it is actively being tested or acted upon. A high-resolution camera and motorized zoom lens allow researchers to see what is happening at the microscopic level during a dynamic experiment, providing real-time visual feedback on contact phenomena.
Closed-loop control modes
The system can operate in three control modes: open-loop (no feedback), constant normal force mode, or constant normal indentation mode. The closed-loop modes allow the system to maintain a specific force or indentation, which is essential for controlled friction experiments and accurately measuring contact forces.
FPGA-based data processing
A Field-Programmable Gate Array (FPGA) is used for high-speed, deterministic calculations. It acquires raw sensor data from the force and displacement sensors at a high rate (3 kHz), multiplies them by matrices to calculate force and displacement vectors, ensuring accurate feedback for the closed-loop control system.

Terminology used across episodes

This episode discusses

The paper

Contact mechanics and friction of soft materials: an apparatus combining multi-axes dynamical actuation/measurement and in situ/in operando visualisation · Read on arXiv

CNRS Ecole Centrale de Lyon Department of Science and Technology, University of Lyon 1 Institute for Materials and Liquids, Université Lyon 1

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: We're looking at the paper: "Contact mechanics and friction of soft materials".

Mira: Here's the gist of the paper. Contact mechanics and friction of soft materials: an apparatus combining multi-axes dynamical actuation/measurement and in situ/in operando visualisation introduces an apparatus dedicated to studying contact mechanics and friction of soft materials which enables simultaneous actuation along five degrees of freedom with in situ / in operando optical monitoring Apparatus Capabilities The apparatus is designed to enable a broader range of soft-contact–related scientific challenges than any single apparatus currently available in the literature It features (i) potentially dynamic actuation along five independent degrees of freedom simultaneously, with three control modes (no feedback, imposed normal force, or imposed indentation) It also includes (ii) real-time monitoring of the six displacements/rotations of one of the two solids in contact and (iii) measurement of the six components of the forces/torques applied at the contact and (iv) in situ / in operando imaging of the contact interface.

Kai: Structural Components and Sensing The structure involves a supporting table, guiding rods, top plate, a 6-axes force/torque sensor, sample holders (upper and lower), goniometers for rotation, piezoelectric translation stage for vertical motion along z, and linear/piezoelectric translation stages for x-y translations The lower sample holder is placed on top of a stack of motorised actuators which includes a high precision xy linear servomotor translation stage enabling translations along x and y axes in the range ±50 mm On top of this stage is a laboratory-made high-load high-stroke capacity piezoelectric translation stage enabling high precision motion of amplitude up to 900 μm along the z axis Between this piezoelectric table and the lower sample holder is a double stepper-motorised goniometer enabling rotations of the lower around the x and y axes in the range ±10°, with a repeatability better than 0.01° per axis The top plate is equipped with a high-resolution camera for contact imaging and a motorised zoom lens, allowing monitoring from above Data Processing Architecture The overall architecture of the real-time software involves acquiring raw outputs from the force sensor via six 24-bit delta-sigma analog-to-digital converters, multiplying by a 6×6 force matrix Kf to get the force vector Simultaneously, the raw outputs from the displacement sensor are acquired through two NI9401 acquisition counters and multiplied by a 6×6 displacement matrix Kd to get the relevant displacement vector To perform these matrix multiplications at a sufficiently high rate for closed-loop control, a field-programmable gate array (FPGA, NI-CRIO 9037) is used to execute calculations at 3 kHz with deterministic timing Control and Dynamic Excitation The closed-loop control function generates the drive signal for the vertical position of the piezoelectric actuator via a 24-bit digital-to-analog converter, operating in three modes: open-loop mode (no feedback), closed-loop constant normal force mode, or closed-loop constant normal indentation mode Furthermore, a sinusoidal numerical signal can be added to the PID loop output to impose a known dynamic excitation on the tribological contact The response to such excitation is extracted from raw signals using a two-phase lockin amplifier, yielding scalars Xω and Yω which determine the amplitude Sω and phase shift θ of the sine component at angular frequency ω Experimental Validation Examples Experiments illustrate capabilities such as sample alignment using custom multi-axes motions to compensate for rotation-induced translations The instrument also allows for well-controlled friction experiments under either constant force or constant displacement thanks to FPGA-implemented closed-loop control Finally, vibration-based detection of first contact is possible by adding a sinusoidal vibration with an amplitude 100 nm at 6 Hz and using lock-in detection to extract the force component at that frequency The developed instrument enables actuating a solid sample with complex kinematics involving five degrees of freedom with nanometer/microradian resolution over strokes as large as 20 mm along x and y, 0.9 mm along z and 20° in θX and θY The first solid can be brought into contact with another one with virtually no size limitation on the thickness of the solids It has potential to be leveraged as a versatile actuation, measurement and visualisation platform to investigate other phenomena from adhesive tape peeling to solid-liquid adhesion Acknowledgments This work was supported by the LABEX iMUST (ANR10-LABX-0064) of Université de Lyon It was also supported by ANR through grants ANR-18-CE08-0011- 01 (project PROMETAF), ANR-21-CE06-0048- 57 (project WEEL) and ANR-22-CE06-0013-- 59 (project CLOSER)> The authors are indebted to the Carnot institute Ingénierie@Lyon, labelled by the French National Research Agency (ANR), for its support and funding> Bibliography The bibliography lists numerous references related to contact mechanics, friction of soft materials, and related experimental techniques.

Mira: The list includes works on adhesion in soft contacts and dynamic indentation methods.

Kai: References The references cited include foundational work on tribology and contact mechanics such as those by Worobets and Wannop and studies on viscoelastic contacts and studies on adhesion.

Paper summary: Kai: This paper, "Contact mechanics and friction of soft materials: an apparatus combining multi-axes dynamical actuation/measurement and in situ/in operando visualisation," introduces a new apparatus dedicated to studying the contact mechanics and friction of soft materials.

Mira: Right. The core thesis is that existing setups only allow for a few degrees of freedom when acting on a contact, but this system allows you to act on the contact with five degrees of freedom simultaneously while visualizing it in situ during the process.

Mira: The conclusion of this paper, "Contact mechanics and friction of soft materials: an apparatus

Conclusion: Kai: So, to wrap up this piece on contact mechanics and friction of soft materials, we’re looking at this apparatus that combines multi-axes dynamical actuation with optical monitoring.

Mira: Exactly. The authors are Matthieu Guibert, Antoine Aymard, Cristobal Oliver, Thibaut Durand, Baptiste Boulet, Djibril Gabriel Kashala, Antoine Mille, Mathieu Leocmach and Loïc Vanel. They put together a system that integrates actuation with measurement in a way that was really hard to get for soft materials before.

Kai: What this means simply is they built a machine that lets you study how soft things touch by moving them in five different directions at the same time while watching everything happen right there, in situ.

Mira: It’s about using that level of control to see how things like adhesive tape peels or how solid and liquid materials stick together by having that dynamical control and the ability to observe it all up close.

Kai: That level of resolution they’re talking about—nanometer or microradian—over motions as big as twenty millimeters along x and y, zero point nine millimeters along z, and twenty degrees in theta x and theta y—that’s a lot of precision.

Mira: It opens up new ways to look at contact because you can impose these complex motions on the sample while you're simultaneously measuring the forces and displacements.

Kai: So it really shifts the focus from just studying a single point of contact to understanding how those large, complex movements affect friction across a whole area of soft material.

Mira: It’s moving us toward seeing those microscopic interactions in a way that was previously totally out of reach with existing tools.

More episodes

← Home