SiC-BN composites with extreme thermal and environmental stability

arXiv:2611.17283 · cond-mat.mtrl-sci · Submitted 2026-11-12 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.

Kai: We're looking at the paper: "SiC-BN composites with extreme thermal and environmental stability".

Mira: Here's the gist of the paper. Ceramic materials capable of maintaining structural integrity under extreme mechanical, thermal, and oxidative environments are essential for applications ranging from space exploration to energy and industrial processing The paper shows that spark plasma sintered composites containing equal weight fractions of hexagonal silicon carbide (6HSiC) and boron nitride (h-BN) exhibit exceptional stability under extreme high-temperature oxidizing conditions and unusually stable temperature-independent thermal conductivity across a broad temperature range Material Synthesis and Characterization The SiC-BN ceramic composites were fabricated via spark plasma sintering (SPS) using 6H-SiC (particle size: 100 nm) and h-BN (particle size: 800 nm) powders The resulting disk has a density of 1.85 g/cm3 and exhibits both the 6H-SiC (JCPDS: 00-022-1273) and h-BN (JCPDS: 00-009-0012) phases Microstructural evaluation reveals pores in the bulk with a pore density of 1.65% Cross-sectional field emission scanning electron microscopy (FESEM) shows both grains and pores Electron probe micro-analysis (EPMA) confirms the presence of elements with obtained wt% of 32.93% (Si), 24.38% (C), 12.56% (B), 27.89% (N), and 2.34% (O) Thermal Transport Stability The effective thermal conductivity of the SiC-BN composite exhibits temperature-independent behavior across a broad range Measurements using lock-in infrared thermography (LIT) show that the effective thermal conductivity remains essentially constant from 25 to 600 °C Steady-state temperature differential radiometry (SSTDR) measurements from 1000 to 1600 °C yield a temperature-independent behavior within the experimental uncertainty This stability is attributed to the complex network of SiC and hBN nanograins, grain boundaries, interfaces, and pores which introduce additional scattering and resistances that suppress temperature-dependent increases in intrinsic anharmonic scattering Extreme Environment Performance The composite withstands prolonged heating and thermal-cycling at surface temperatures reaching >1500 °C under high-velocity oxygen-fuel torch exposure in air Pure 6H-SiC and h-BN rapidly fracture or erode under the same conditions The composite retains its structure at ≥1500 °C without any mass loss or visible microcrack formation after a 6-minute continuous torch exposure Thermal cycling tests demonstrate excellent thermal-shock resistance during temperature drops from 1500 to 300 °C without crack formation Interfacial Stability and Mechanical Properties ReaxFF molecular dynamics simulations reveal thermally driven interfacial reconstruction, forming a Si-N/C-B-rich bonding network, which enhances the interfacial cohesion at elevated temperatures The C-on-B interface exhibits the highest reconstruction-onset temperature, indicating higher resistance to thermally induced interfacial reconstruction Mechanical properties show that the Young’s modulus (E) and hardness (H) are largely retained at 800 °C Fracture toughness is estimated to be 2.02 MPa·m1/2 Thermal Stress Mitigation Mechanism The superior thermal stability of the composite arises from a synergistic interaction between the two phases that mitigates the weaknesses of each material individually The 6H-SiC provides high mechanical strength, while h-BN contributes to thermal-shock resistance by accommodating strain during rapid heating Furthermore, porosity plays a key role in enhancing thermal stability as pores slow down heat transfer into the bulk and minimize temperature differentials that lead to crack formation The low coefficient of thermal expansion (CTE) of 2.9×10−6 /°C further limits thermally-induced strain This lightweight, easily machinable ceramic composite will be a promising structural material in extreme environment applications The composite's lightweight nature, stable thermal transport, and thermal-shock resistance make it useful in aerospace propulsion, combustion engines, and advanced manufacturing related high-temperature structural components It addresses the critical gap by enabling precise manufacturing with design flexibility and stable thermal transport References Wyatt, B.

Kai: C., Nemani, S.

Mira: K., Hilmas, G.

Kai: E., Opila, E.

Title and authors: Kai: The paper we're discussing is "SiC-BN composites with extreme thermal and environmental stability." It’s about creating a new type of ceramic that can handle really tough conditions.

Mira: Yeah, the authors are a big team including folks from Rice University, Stony Brook University, and Penn State. They are tackling how to make ceramics that stay strong when they get super hot or exposed to harsh chemicals.

Kai: It really seems like the synergy between the two phases—the 6H-SiC providing mechanical strength and the h-BN contributing to thermal shock resistance—is what makes this composite so good at handling these extreme environments compared to using either material alone <ref:2611.17283#pg3>.

The paper's summary: Kai: So, the core of this paper, "SiC-BN composites with extreme thermal and environmental stability," is about showing that these specific spark plasma sintered composites are remarkably stable under high heat and oxidation compared to their pure components.

Mira: Basically, they demonstrated that when you combine equal weight fractions of hexagonal silicon carbide and boron nitride, you get exceptional stability under extreme high-temperature oxidizing conditions and an unusually stable temperature independent thermal conductivity across a broad temperature range.

Lev: So it’s not just the individual components being tough; it's the way they are combined that creates this new level of performance.

Kai: That means we can use this as a structural material in extreme conditions, which is what the graphical abstract suggests, making it promising for applications where things have to be reliable and lightweight.

Mira: They’re specifically highlighting the lightweight and machinable nature of this material as key selling points because they believe it addresses a critical gap by enabling precise manufacturing with design flexibility and stable thermal transport.

Lev: So, the implication is that we can start thinking about this for things like aerospace propulsion or combustion engines where thermal management is a real issue.

Kai: And they’re showing that their approach isn't just about surviving; it’s about having stable properties across a wide temperature spectrum, which is what makes it useful structurally.

Mira: They are also detailing how the microstructure—the pores and interfaces—plays a critical role in mitigating thermal stress through heat flux mapping, while ReaxFF simulations reveal that thermally driven interfacial reconstruction forms a silicon nitrogen boron carbon rich bonding network that boosts cohesion at high temperatures.

Lev: So the paper is telling us that structural stability isn't just about the bulk material; it’s about understanding how all those tiny micro features work together to manage stress and bonding under heat.

Kai: That's a deep dive into the mechanics of how these composites achieve their performance characteristics, which is what makes this paper genuinely interesting.

Mira: The fact that they are linking thermal transport stability to the complex nanostructure is what gives the results a lot of depth beyond just saying "it works."

Lev: I see. So they’re not just giving us a material that works; they're explaining *why* it works by connecting the microscopic features to the macroscopic stability.

Kai: It’s about showing that you can use computational tools to build a better understanding of these complex ceramic systems than was previously possible.

Mira: I think this moves us closer to being able to design materials for extreme environments with more certainty because we’re not just guessing at the behavior, we have the data on how it happens.

Lev: It’s moving from just empirical testing toward a more predictive science in this area of materials science.

The paper's improvements: Kai: Moving into what the authors suggest for future work, they are pushing to improve predictive modeling by integrating ReaxFF molecular dynamics simulations to predict that thermally driven interfacial reconstruction and the formation of a silicon nitrogen boron carbon rich bonding network at elevated temperatures.

Mira: They also propose training AI models on temperature regimes where the effective thermal conductivity exhibits this temperature independent behavior so we can reliably estimate bulk heat transport across a broad range, specifically from twenty-five to six hundred degrees Celsius.

Lev: That’s a big leap for simulation tools because predicting that constant conductivity across such a wide range is something that would be incredibly useful for engineering design.

Kai: They also suggest developing robust finite element analysis modules capable of incorporating microstructure resolved models that account for intrinsic porosity mitigating thermal stress and thermally driven interfacial reconstruction, which lets the AI simulate complex heat flux distributions and predict failure mechanisms like those seen in the SiC-BN composite.

Mira: And they propose refining surface degradation prediction by utilizing post impact characterization data, such as EPMA compositional maps showing the formation of a silicon dioxide rich top layer, to anticipate material response after extreme kinetic events like high velocity oxygen fuel torch impact tests.

Kai: And they suggest optimizing interfacial bond stability prediction by training models on ReaxFF simulation results to identify that the carbon on boron interface exhibits the highest reconstruction onset temperature, allowing AI to prioritize or design composite architectures that maximize resistance to thermally induced interfacial reconstruction in extreme conditions.

Mira: It sounds like they are focusing on using these advanced simulations and AI not just for confirmation, but for genuine prediction of material behavior under novel stresses.

Lev: That’s the right direction because if we can get those models accurate enough, we can start designing materials that perform reliably where they need to go.

Conclusion: Kai: So, wrapping up the paper on "SiC-BN composites with extreme thermal and environmental stability," the main point is that this composite material shows exceptional stability under high heat and oxidation compared to pure components.

Mira: They showed that combining these two materials yields structural integrity in extreme conditions, which is what makes it a promising candidate for applications where things have to be reliable and lightweight.

Kai: This work opens up avenues for designing ceramic composites for aerospace propulsion or combustion engines where thermal management is a critical challenge because they have this material that shows stability under punishing conditions.

Mira: I think we can start using this as a foundation to design structural components with more certainty, moving from just guessing at the behavior to having data on how it actually happens.

Lev: If we can get those predictive models accurate enough, then we can start designing materials that perform reliably where they need to go.

Kai: We're looking forward to seeing what these new computational approaches can achieve next with this SiC-BN composite material.

Abhijit Biswas, *Eugenio Garcia-Granados, *Saman Zare, *Mozhdeh Mirakhory, JungHun Park, Shuvodeep De, Jessica Reyes3, Hunter B. Schonfeld3, Noah A. Burke7, William Riffe7, Michael S. Lafferty3, Sudaice Kazibwe8, Maryam Amiri1, Shreyasi Chattopadhyay1, Mingrui Xu1, Gelu Costin9, Tanguy Terlier10, Jianhua Li12, Ching-Wu Chu8, Liangzi Deng8, Bharat K. Jasthi13, Manoj Tripathi14, Venkataramana Gadhamshetty14, Gi-Dong Sim5, Kathy Lu15, Adri C. T. van Duin4,16,17, Patrick E. Hopkins3,7, Michael S. Lafferty3, *Sanjay Sampath2 and *Pulickel M Ajayan*, Abhijit Biswas@rice.edu; phopkins@virginia.edu; sanjay.sampath@stonybrook.edu; ajayan@rice.edu

Department of Materials Science and NanoEngineering, Rice University · Center for Thermal Spray Research, Stony Brook University · Department of Mechanical and Aerospace Engineering, University of Virginia · Department of Mechanical Engineering, The Pennsylvania State University · Korea Advanced Institute of Science and Technology · Ingram School of Engineering, Texas State University · Department of Materials Science and Engineering, University of Virginia Department 7 · Department of Physics and Texas Center for Superconductivity (TcSUH) University of Houston Department 8 · Department of Earth, Environmental and Planetary Sciences, Rice University Department 9 · SIMS Laboratory Shared Equipment Authority Rice University Department 10 Chemical & Biomolecular Engineering Rice University Department 11 Shared Equipment Authority Rice University Department 12 South Dakota School of Mines & Technology Department 13 Civil & Environmental Engineering South Dakota School of Mines & Technology Department 14 Materials and Metallurgical Engineering South Dakota School of Mines & Technology · Department of Mechanical and Materials Engineering University of Alabama at Birmingham

cond-mat.mtrl-sci

Submitted: 2026-11-12

Updated: 2026-11-12

Comments: 76 Pages, 4 Main Figures, 30 SI Figures, 8 Tables, Authors version, Comments are welcome

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 83/100

The gist: Ceramic materials capable of maintaining structural integrity under extreme mechanical, thermal, and oxidative environments are essential for applications ranging from space exploration to energy and…

Key concepts

Spark Plasma Sintering (SPS)
This is a manufacturing technique used to create dense ceramic materials quickly. It uses pulsed direct current combined with pressure and heat simultaneously. In this study, SPS was used to combine 6H-SiC and h-BN powders into a solid disk with high density (~1.85 g/cm3), which is crucial for achieving the desired microstructure.
Temperature-Independent Thermal Conductivity
The composite material maintains a constant rate of heat transfer even when exposed to very high temperatures (up to 600°C) and extremely high temperatures (up to 1600°C). This stability is due to the complex network of SiC and h-BN nanograins, grain boundaries, and pores, which scatter phonons effectively. This property is vital for reliable thermal management in extreme environments.
Thermally Driven Interfacial Reconstruction
Molecular dynamics simulations revealed that at high temperatures, the interface between silicon carbide (SiC) and boron nitride (BN) chemically changes. This process forms a new, stronger bonding network rich in Si-N and C-B bonds. This reconstruction significantly improves the material's cohesion and resistance to thermal damage at elevated temperatures.
Synergistic Thermal Stress Mitigation
The composite's superior performance comes from how the two phases work together. 6H-SiC provides high mechanical strength, while h-BN helps absorb strain during rapid heating. Furthermore, internal pores slow down heat transfer and minimize temperature differences that cause cracks, creating a robust system against thermal shock.

Terminology

Summary

Ceramic materials capable of maintaining structural integrity under extreme mechanical, thermal, and oxidative environments are essential for applications ranging from space exploration to energy and industrial processing The paper shows that spark plasma sintered composites containing equal weight fractions of hexagonal silicon carbide (6HSiC) and boron nitride (h-BN) exhibit exceptional stability under extreme high-temperature oxidizing conditions and unusually stable temperature-independent thermal conductivity across a broad temperature range

Material Synthesis and Characterization

The SiC-BN ceramic composites were fabricated via spark plasma sintering (SPS) using 6H-SiC (particle size: 100 nm) and h-BN (particle size: 800 nm) powders The resulting disk has a density of 1.85 g/cm3 and exhibits both the 6H-SiC (JCPDS: 00-022-1273) and h-BN (JCPDS: 00-009-0012) phases Microstructural evaluation reveals pores in the bulk with a pore density of 1. p. 4

Where the paper says it

1a) with a density of ~1. We performed X-ray diffraction (XRD) upto 1000 °C, showing both the 6H-SiC (JCPDS: 00- 022-1273) and h-BN (JCPDS: 00-009-0012) phases and their phase stability (Fig.

65% Cross-sectional field emission scanning electron microscopy (FESEM) shows both grains and pores Electron probe micro-analysis (EPMA) confirms the presence of elements with obtained wt% of 32. p. 4
Where the paper says it

Cross-sectional field emission scanning electron microscopy (FESEM) shows both grains, and also the pores (Fig. Electron probe micro-analysis (EPMA) backscattered electron (BSE) image and its wavelength dispersive spectrometry (WDS) compositional map (Supplementary Fig.

93% (Si), 24.38% (C), 12.56% (B), 27.89% (N), and 2.34% (O)

Thermal Transport Stability

The effective thermal conductivity of the SiC-BN composite exhibits temperature-independent behavior across a broad range Measurements using lock-in infrared thermography (LIT) show that the effective thermal conductivity remains essentially constant from 25 to 600 °C Steady-state temperature differential radiometry (SSTDR) measurements from 1000 to 1600 °C yield a temperature-independent behavior within the experimental uncertainty This stability is attributed to the complex network of SiC and hBN nanograins, grain boundaries, interfaces, and pores which introduce additional scattering and resistances that suppress temperature-dependent increases in intrinsic anharmonic scattering

Extreme Environment Performance

The composite withstands prolonged heating and thermal-cycling at surface temperatures reaching >1500 °C under high-velocity oxygen-fuel torch exposure in air Pure 6H-SiC and h-BN rapidly fracture or erode under the same conditions The composite retains its structure at ≥1500 °C without any mass loss or visible microcrack formation after a 6-minute continuous torch exposure Thermal cycling tests demonstrate excellent thermal-shock resistance during temperature drops from 1500 to 300 °C without crack formation

Interfacial Stability and Mechanical Properties

ReaxFF molecular dynamics simulations reveal thermally driven interfacial reconstruction, forming a Si-N/C-B-rich bonding network, which enhances the interfacial cohesion at elevated temperatures The C-on-B interface exhibits the highest reconstruction-onset temperature, indicating higher resistance to thermally induced interfacial reconstruction Mechanical properties show that the Young’s modulus (E) and hardness (H) are largely retained at 800 °C Fracture toughness is estimated to be 2.02 MPa·m1/2

Thermal Stress Mitigation Mechanism

The superior thermal stability of the composite arises from a synergistic interaction between the two phases that mitigates the weaknesses of each material individually The 6H-SiC provides high mechanical strength, while h-BN contributes to thermal-shock resistance by accommodating strain during rapid heating Furthermore, porosity plays a key role in enhancing thermal stability as pores slow down heat transfer into the bulk and minimize temperature differentials that lead to crack formation The low coefficient of thermal expansion (CTE) of 2.9×10−6 /°C further limits thermally-induced strain

Conclusion and Application Potential

This lightweight, easily machinable ceramic composite will be a promising structural material in extreme environment applications The composite's lightweight nature, stable thermal transport, and thermal-shock resistance make it useful in aerospace propulsion, combustion engines, and advanced manufacturing related high-temperature structural components It addresses the critical gap by enabling precise manufacturing with design flexibility and stable thermal transport

References

Wyatt, B. C., Nemani, S. K., Hilmas, G. E., Opila, E. J. & Anasori, B. Ultra-high temperature ceramics for extreme environments Fahrenholtz, W. p. 3

Where the paper says it

4 Main Ceramics capable of maintaining structural integrity under extreme mechanical, thermal, and oxidative environments are essential for applications, ranging from space exploration to energy and industrial processing1–6 . Monolithic ultrahigh-temperature ceramics are key to many high-performance systems owing to their chemical stability 2000 °C, yet their ability to endure such extreme conditions remains a persistent limitation7–9 .

G. & Hilmas, G. E. Ultra-high temperature ceramics: Materials for extreme environments Nisar, A. p. 3
Where the paper says it

4 Main Ceramics capable of maintaining structural integrity under extreme mechanical, thermal, and oxidative environments are essential for applications, ranging from space exploration to energy and industrial processing1–6 . Monolithic ultrahigh-temperature ceramics are key to many high-performance systems owing to their chemical stability 2000 °C, yet their ability to endure such extreme conditions remains a persistent limitation7–9 .

, Hassan, R., Agarwal, A. & Balani, K. Ultra-high temperature ceramics: Aspiration to overcome challenges in thermal protection systems Eswarappa Prameela, S. p. 3
Where the paper says it

4 Main Ceramics capable of maintaining structural integrity under extreme mechanical, thermal, and oxidative environments are essential for applications, ranging from space exploration to energy and industrial processing1–6 . Monolithic ultrahigh-temperature ceramics are key to many high-performance systems owing to their chemical stability 2000 °C, yet their ability to endure such extreme conditions remains a persistent limitation7–9 .

et al. Materials for extreme environments Uyanna, O. p. 3
Where the paper says it

Furthermore, steep thermal gradients, chemically aggressive environments, and high mechanical loading induces thermal stress, promoting surface ablation and microstructural degradation, ultimately leading to catastrophic failures 7,10 . Composite ceramic materials offer a compelling pathway to overcome these limitations by integrating multiple phases across length scales, as they can decouple and redistribute thermal and mechanical loads, enabling enhanced thermal-shock resistance, oxidation, and erosion.

& Najafi, H. Thermal protection systems for space vehicles: A review on technology development, current challenges and future prospects Padture N. p. 3
Where the paper says it

4 Main Ceramics capable of maintaining structural integrity under extreme mechanical, thermal, and oxidative environments are essential for applications, ranging from space exploration to energy and industrial processing1–6 . Monolithic ultrahigh-temperature ceramics are key to many high-performance systems owing to their chemical stability 2000 °C, yet their ability to endure such extreme conditions remains a persistent limitation7–9 .

P. et al. Thermal Barrier Coatings for Gas-Turbine Engine Applications Wuchina, E. p. 2
Where the paper says it

3 Abstract Ceramic materials that maintain structural integrity and resist thermal-shock under extreme conditions are critical for many applications. Here we show that spark plasma sintered composites containing equal weight fractions of hexagonal silicon carbide (6HSiC) and boron nitride (h-BN) exhibit exceptional stability under extreme high-temperature oxidizing conditions and unusually stable temperature-independent thermal conductivity across a broad temperature range.

, Opila, E., Opeka, M., Fahrenholtz, B. & Talmy, I. UHTCs: Ultra-High Temperature Ceramic Materials for Extreme Environment Applications Govender, S. p. 2
Where the paper says it

3 Abstract Ceramic materials that maintain structural integrity and resist thermal-shock under extreme conditions are critical for many applications. Here we show that spark plasma sintered composites containing equal weight fractions of hexagonal silicon carbide (6HSiC) and boron nitride (h-BN) exhibit exceptional stability under extreme high-temperature oxidizing conditions and unusually stable temperature-independent thermal conductivity across a broad temperature range.

& Friedrich, H. B. Monoliths: A Review of the Basics, Preparation Methods and Their Relevance to Oxidation Zeng, Y. p. 2
Where the paper says it

Under high-velocity oxygen-fuel torch exposure in air, it withstands prolonged heating and thermal-cycling at surface temperatures reaching >1500 °C, whereas pure 6H-SiC and h-BN rapidly fractures or erodes. Microstructural evaluation shows the formation of a multi-phase surface silica layer that further protects the material from oxidation.

et al. Ablation-resistant carbide Zr0. p. 3
Where the paper says it

Their highdensity, brittleness with limited machinability, restricts their use in complex, and weightsensitive designs. Furthermore, steep thermal gradients, chemically aggressive environments, and high mechanical loading induces thermal stress, promoting surface ablation and microstructural degradation, ultimately leading to catastrophic failures 7,10 .

8Ti0.2C0.74B0.26 for oxidizing environments up to 3,000 °C Bale, H. p. 2
Where the paper says it

3 Abstract Ceramic materials that maintain structural integrity and resist thermal-shock under extreme conditions are critical for many applications. Here we show that spark plasma sintered composites containing equal weight fractions of hexagonal silicon carbide (6HSiC) and boron nitride (h-BN) exhibit exceptional stability under extreme high-temperature oxidizing conditions and unusually stable temperature-independent thermal conductivity across a broad temperature range.

A. et al. Real-time quantitative imaging of failure events in materials under load at temperatures above 1,600 °C Squire, T. p. 7
Where the paper says it

From 25 to 600 °C, the LIT measurements yield 𝑘𝑒𝑓𝑓 of ~8. The central values increase modestly at lower temperatures and then remain nearly unchanged through 600 °C, within the experimental uncertainty.

H. & Marschall, J. Material property requirements for analysis and design of UHTC components in hypersonic applications Dong, Y. p. 3
Where the paper says it

hypersonic vehicle skins and leading edges, propulsion components, and advanced manufacturing, materials are not required to endure the absolute highest temperatures, but rather to reliably survive applicationrelevant thermal conditions, while offering structural integrity, low-density, and ease of fabrication15–18 . Therefore, lightweight ceramic composites that can address this critical gap by enabling precise manufacturing with design flexibility, stable thermal transport with excellent thermal-shock resistance, would be more suitable as extreme condition materials where efficiency and adaptability are as important as thermal endurance18–20 .

, Wang, E., You, Y., Yin, C. Thermal Protection System and Thermal Management for Combined-Cycle Engine: Review and Prospects Zhang Q. p. 3
Where the paper says it

During prolonged highvelocity oxygen-fuel (HVOF) torch exposure as well as thermal-cycling, the composite retains its structure at 1500 °C, whereas pure 6H-SiC and h-BN undergo catastrophic fracture or rapid erosion. Combined microstructural evaluation, finite element analyses,

et al. Review of Lightweight, High-Temperature Thermal Insulation Materials for Aerospace Wang, X. p. 0
Where the paper says it

Ajayan1 * AFFILIATIONS 1Department of Materials Science and Nanoengineering, Rice University, Houston, TX, 77005, USA 2Center for Thermal Spray Research, Stony Brook University, 130 Heavy Engineering Bldg. , Stony Brook, NY 11794-2275, USA 3Department of Mechanical and Aerospace Engineering, University of Virginia, Charlottesville, VA 22904, USA 4Department of Mechanical Engineering, The Pennsylvania State University, University Park, PA 16802, USA 5Department of Mechanical Engineering, Korea Advanced Institute of Science and Technology, 291, Daehak-ro, Yuseong-gu, Daejeon 34141, Republic of Korea 6 Ingram School of Engineering, Texas State University, San Marcos, TX, 78666-4684, USA 7Department of Materials Science and Engineering, University of Virginia, Charlottesville, VA 22904, USA 8Department of Physics and Texas Center for Superconductivity (TcSUH), University of Houston, Houston, TX, 77004, USA 9Department of Earth, Environmental and Planetary Sciences, Rice University, Houston, TX, 77005, USA 10SIMS Laboratory, Shared Equipment Authority, Rice University, Houston, TX, 77005, USA 11Department of Chemical & Biomolecular Engineering, Rice University, Houston, TX, 77005, USA 12Shared Equipment Authority, Rice University, Houston, TX, 77005, USA 13Department of Materials and Metallurgical Engineering, South Dakota School of Mines & Technology, 501 East Saint Joseph St, Rapid City, SD 57701, USA 14Civil & Environmental Engineering, South Dakota School of Mines & Technology, Rapid City, SD 57701, USA 15Department of Mechanical and Materials Engineering, University of Alabama at Birmingham, Birmingham, AL, 35294, USA 16Department of Chemical Engineering, The Pennsylvania State University, University Park, PA 16802, USA 17Department of Materials Science and Engineering, The Pennsylvania State University, University Park, PA 16802, USA 18Department of Physics, University of Virginia, Charlottesville, VA 22904, USA These authors contributed equally: Eugenio Garcia-Granados, Saman Zare, Mozhdeh Mirakhory, JungHun Park, Shuvodeep De *Corresponding authors: abhijit.

, Qiao, G. & Jin, Z. Fabrication of Machinable Silicon Carbide-Boron Nitride Ceramic Nanocomposites Fenetaud, P. p. 2
Where the paper says it

This lightweight, easily machinable ceramic composite will be a promising structural material in extreme environment applications. Keywords: Composite, silicon carbide, boron nitride, impact, thermal stability

& Jacques, S. SiC/SiC ceramic matrix composites with BN interphase produced by gas phase routes: An overview Yang, Z. p. 6
Where the paper says it

1: Characterization of sintered SiC-BN composites. a, Temperature-dependent XRD pattern in air showing the Bragg reflections of 6H-SiC and h-BN phase, respectively, demonstrating the phase stability.

-H. et al. Oxidation resistance of hot-pressed SiC–BN composites Kim, K. p. 7
Where the paper says it

The measured 𝑘𝑒𝑓𝑓 by using SSTDR (steady-state temperature differential radiometry) from ~1000 to 1560 °C, also shows temperature-independent behavior within experimental uncertainty, demonstrating stable thermal transport across this hightemperature regime. For comparison, the thermal conductivities of spark plasma sintered h-BN (SPS h-BN), single crystal SiC (SC-SiC), and hot-pressed SiC (HP-SiC) are shown.

J., Cho, T.-Y., Kim, Y.-W., Nishimura, T. & Narimatsu, E. Electrical and thermal properties of silicon carbide–boron nitride composites prepared without sintering additives Kultayeva, S. p. 2
Where the paper says it

3 Abstract Ceramic materials that maintain structural integrity and resist thermal-shock under extreme conditions are critical for many applications. Here we show that spark plasma sintered composites containing equal weight fractions of hexagonal silicon carbide (6HSiC) and boron nitride (h-BN) exhibit exceptional stability under extreme high-temperature oxidizing conditions and unusually stable temperature-independent thermal conductivity across a broad temperature range.

, Kim, Y.-W. & Song, I.-H. Influence of sintering atmosphere and BN additives on microstructure and properties of porous SiC ceramics van Duin, A. C. T., Dasgupta, S., Lorant, F. & Goddard, W. A. ReaxFF: A Reactive Force Field for Hydrocarbons Senftle, T. p. 4
Where the paper says it

1h and Supplementary Fig. Although the interface is not atomically smooth, the reactive force-field (ReaxFF)26,27 molecular dynamics simulations reveals that at ambient conditions Si-on-N is the most stable interface with the lowest formation energy (Supplementary Fig.

P. et al. The ReaxFF reactive force-field: development, applications and future directions Lu, J. p. 4
Where the paper says it

1h and Supplementary Fig. Although the interface is not atomically smooth, the reactive force-field (ReaxFF)26,27 molecular dynamics simulations reveals that at ambient conditions Si-on-N is the most stable interface with the lowest formation energy (Supplementary Fig.

et al. Molecular dynamics simulation of the temperature effect on ideal mechanical properties of SiC/BN interface for SiCf/SiC composites Schonfeld, H. p. 4
Where the paper says it

5 and temperature-dependent ReaxFF molecular dynamics simulations show: (a) formation of a mixed-phase surface silica layer, (b) porosity mitigating thermal stress, and (c) thermally-driven interfacial reconstruction with the formation of a Si-N/C-B-rich bonding network, contributing synergistically to its structural integrity. This shows the potential of SiC-BN composite as a robust structural material in extreme environments.

B. et al. Closing the ultrahigh temperature metrology gap: Non-contact thermal conductivity (k) and spectral emittance (ɛλ) of molybdenum up to 3200 K Cahill D. p. 3
Where the paper says it

4 Main Ceramics capable of maintaining structural integrity under extreme mechanical, thermal, and oxidative environments are essential for applications, ranging from space exploration to energy and industrial processing1–6 . Monolithic ultrahigh-temperature ceramics are key to many high-performance systems owing to their chemical stability 2000 °C, yet their ability to endure such extreme conditions remains a persistent limitation7–9 .

G. et al. Nanoscale thermal transport. p. 3
Where the paper says it

hypersonic vehicle skins and leading edges, propulsion components, and advanced manufacturing, materials are not required to endure the absolute highest temperatures, but rather to reliably survive applicationrelevant thermal conditions, while offering structural integrity, low-density, and ease of fabrication15–18 . Therefore, lightweight ceramic composites that can address this critical gap by enabling precise manufacturing with design flexibility, stable thermal transport with excellent thermal-shock resistance, would be more suitable as extreme condition materials where efficiency and adaptability are as important as thermal endurance18–20 .

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved predictive modeling of extreme environment material performance by integrating ReaxFF molecular dynamics simulations to predict thermally driven interfacial reconstruction and the formation of a Si-N/C-B-rich bonding network at elevated temperatures. This allows AI systems to accurately forecast structural integrity under conditions like high-velocity oxygen-fuel torch exposure.

  2. Enhanced thermal conductivity prediction capability by training AI models on temperature regimes where the effective thermal conductivity keff exhibits temperature-independent behavior. This enables the system to reliably estimate bulk heat transport across a broad range, specifically from 25 to 1600 degrees Celsius, which is crucial for structural material design.

  3. Development of a robust finite element analysis (FEA) module capable of incorporating microstructure-resolved models that account for intrinsic porosity mitigat[ing] thermal stress and thermally-driven interfacial reconstruction. This allows the AI to simulate complex heat flux distributions and predict failure mechanisms, such as those observed in the SiC-BN composite.

  4. Refined surface degradation prediction by utilizing post-impact characterization data, such as EPMA compositional maps showing the formation of a SiO2-rich top layer, to anticipate material response after extreme kinetic events like HVOF torch impact tests. This enables AI to predict the formation of protective surface layers and their subsequent thermal stability during thermal cycling.

  5. Optimization of interfacial bond stability prediction by training models on ReaxFF simulation results, identifying that the C-on-B interface exhibits the highest reconstruction-onset temperature. This allows AI to prioritize or design composite architectures that maximize resistance to thermally induced interfacial reconstruction in extreme conditions.

Abstract

Ceramic materials that maintain structural integrity and resist thermal-shock under extreme conditions are critical for many applications. Here we show that spark plasma sintered composites containing equal weight fractions of hexagonal silicon carbide (6H-SiC) and boron nitride (h-BN) exhibit exceptional stability under extreme high-temperature oxidizing conditions and unusually stable temperature-independent thermal conductivity across a broad temperature range. Under high-velocity oxygen-fuel torch exposure in air, it withstands prolonged heating and thermal-cycling at surface temperatures reaching >1500 °C, whereas pure 6H-SiC and h-BN rapidly fractures or erodes. Microstructural evaluation shows the formation of a multi-phase surface silica layer that further protects the material from oxidation. Finite-element analysis heat-flux map shows that intrinsic porosity mitigates thermal stress, while ReaxFF molecular dynamics simulations reveal thermally driven interfacial reconstruction and the formation of a Si-N/C-B-rich bonding network, enhancing the interfacial cohesion at elevated temperatures. This lightweight, easily machinable ceramic composite will be a promising structural material in extreme environment applications.

Sources

Related papers