Fluid drags on a sphere at finite Reynolds number--a classical problem examined afresh

arXiv:2610.00334 · physics.flu-dyn · Submitted 2026-09-29 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: We're looking at the paper: "Fluid drags on a sphere at finite Reynolds number--a classical problem examined afresh".

Mira: Here's the gist of the paper. Evaluating the drag coefficient Cd for a sphere moving in a fluid at finite Reynolds number Re has become a classical research subject in fluid dynamics, with publications appearing continuously by numerous authors over the years due to the unavailability of closed-form mathematical solutions To date, mathematical formulas for calculating Cd as a function of Re can only be obtained by correlation curve-fitting to experimental data The present study focuses on examining the accuracy of Klyachko’s 1934 formula for Cd(Re) with two common fractions as fitting parameters, which could enable closed-form integration of a simplified equation governing rectilinear motion of aerosol spheres The computed values of root-mean-square relative error from recently developed formulas show reasonable accuracy of the Klyachko formula for Re ≤ 1000 and its extension to Re < 3 × 10 5 as a piecewise continuous function Hence, a few demonstrative examples are presented using the extended Klyachko formula in the study of rectilinear acceleration, the calculation of the terminal velocity of aerosol spheres, and so forth, to shed fresh light on how this classical problem can be studied.

Kai: Pruning redundant reasoning tokens The paper addresses the long-standing issue where closed-form analytical solutions for flow around rigid and fluid spheres are limited to very low values of the Reynolds number Knowledge about the situation at higher Reynolds numbers must resort to experimental measurements, numerical computations, as well as approximations based on boundary-layer theory The drag coefficient Cd is often presented as a graph versus Re known as the ”Rayleigh curve” or “standard drag curve” (Clift, Grace, and Weber, 1978).

Mira: Despite tremendous efforts by generations after generations of mathematically talented scientists, closed-form analytical solutions for flow around rigid and fluid spheres are effectively limited to very low values of the Reynolds number.

Kai: Comparison of Cd(Re) with a reference formula The study compares the extended Klyachko formula (1) with recently developed correlation formulas, such as those by Brown and Lawler (2003) or others, using the root-mean-square relative error (RMSRE) Table 1 presents the values of RMSRE (2) with f(x) for the Cd(Re) in (1) and the reference function F(x) for the correlation formulas by recent authors, integrated from Re = 0.01 to Re = 1000, 900, 800, and 500 as well as Re = 10 cubed to Re = 2 × 10 5 Apparently, for the interval of Rem ≤ Re < Rem where Rem is chosen as 900 in the modified formula (3), the RMSRE values are consistently lowest for (1) versus the correlation formula of Cheng (2009).

Title and authors: Kai: So Mira we're looking at this paper today titled Fluid drags on a sphere at finite Reynolds number--a classical problem examined afresh. It sounds like they are taking an old problem in fluid dynamics and trying to look at it with fresh eyes.

Mira: Yeah, the authors are trying to address the fact that for a long time we've only had these correlation curves to figure out the drag coefficient Cd as a function of Reynolds number Re. They say this study focuses on testing Klyachko’s one thousand nine hundred thirty-four formula with two common fractions as fitting parameters because that might let them get a closed-form integration for the equation governing rectilinear motion of aerosol spheres <ref:2610.00334#pg1,with two common fractions as fitting parameters>.

Lev: From an engineering standpoint, having a closed-form solution for rectilinear motion is really useful, especially when you're dealing with aerosol particles where gravity might be ignored. It means you can actually solve the differential equations instead of relying on fitting data to a curve.

Kai: Exactly, Lev. The paper says that they computed the root-mean-square relative error from recently developed formulas shows reasonable accuracy for Klyachko's formula for Reynolds numbers less than or equal to one thousand and its extension up to three times ten five as a piecewise continuous function <ref:2610.00334#pg1,root-mean-square relative error from recently developed formulas>.

Mira: That means it seems like this Klyachko formula is pretty solid up to that point, but they also show where the error gets bigger, especially near the drag crisis around three times ten five.

Lev: That's important because if you're building hardware for real applications, you need to know exactly where the assumptions of these formulas start to break down.

Kai: And they use this Klyachko formula in a few demonstrative examples, like studying rectilinear acceleration and calculating the terminal velocity of aerosol spheres just to show how it works in practice.

Mira: It’s also useful because they use it to derive equations for the rectilinear motion of a spherical particle under quasistatic drag, which is a pretty neat analytical solution similar to what Serafini and Putnam did back in one thousand nine hundred fifty-four or Putnam in one thousand nine hundred sixty-one <ref:2610.00334#pg1>.

Lev: That analytical solution for the velocity u would be much better than just using an empirical formula because it gives you a function of time t directly, showing how fast it accelerates.

Kai: And then there's the terminal settling velocity calculation too, where they use force balance to find that velocity based on a given Cd and density. They show how you can calculate non-dimensional parameters like d star and u star as functions of Reynolds number Re using equations like one twenty-six ten point zero zero three three four page one of that work reads Fluid drag on a sphere at finite Reynolds number--a classical problem examined afresh.

Title and authors: Mira: So the main improvement here is quantitatively understanding how good or bad this extended Klyachko formula actually is for real applications, showing it's accurate for Re less than one thousand or even better, less than nine hundred.

Lev: That level of accuracy for the lower Reynolds number range is what makes it viable for practical modeling in aerosol studies.

Kai: And they show that the RMSRE values are consistently lowest for this formula versus other correlation formulas in the lower Reynolds number range, and acceptable for real-world applications especially when Re is less than one thousand <ref:2610.00334#pg1>.

Mira: So the main contribution is that it establishes a reliable formula for Cd(Re) and then uses it to create closed-form analytical solutions for rectilinear acceleration when gravity is ignored.

Lev: That closed-form solution for the acceleration of an aerosol sphere across the range zero to three times ten five is pretty significant because it moves us away from just relying on whatever curve you fit to experimental data.

Kai: And they also demonstrate how you can use this extended Klyachko formula to calculate the spherical particle diameter and terminal settling velocity as functions of Reynolds number, getting results that agree well with Brown and Lawler's or Cheng's correlation formulas.

Mira: It sounds like a solid foundation for using this formula in things like modeling the dynamical process of an aerosol sphere accelerating toward its terminal velocity, which they compare to solutions for water droplets falling in air when deformations are negligible.

Lev: That comparison with Wang and Pruppacher's work from one thousand nine hundred seventy-seven adds some nice context to how these analytical solutions hold up when compared against other classical fluid dynamics results <ref:2610.00334#pg1>.

Kai: So, essentially, the paper shows that this older formula isn't just a historical curiosity; it’s accurate enough for many practical scenarios and it can be used to derive useful analytical tools for motion modeling.

Mira: It really bridges the gap between classical theory and modern data fitting by providing a formula with known accuracy bounds in specific regimes, which is what we need when we're trying to make sense of complex fluid flows.

Lev: And the fact that they can derive equations for rectilinear acceleration just by ignoring gravity shows how much useful physics you can extract even from simplified systems.

Kai: Before we wrap up, Lev, what does this mean for running this on real hardware? What are the overheads when you try to implement these derived solutions?

Title and authors: Lev: Implementing that closed-form solution means you're dealing with a system where the time evolution t is directly related to the particle’s velocity, so you need a fast way to compute that integral over time. The main overhead would be in accurately calculating the function of Reynolds number Re itself, which involves those fitting parameters.

Mira: And for me, I'd say it really depends on whether you need that extreme precision or if the reasonable accuracy they show is enough for your specific theoretical model. They clearly flag that its accuracy is best for Reynolds numbers below nine hundred and ten thousand five as a piecewise function.

Kai: It’s a good balance, then, using this formula where it’s most accurate while still getting the benefit of an analytical solution instead of just fitting noise to experimental points.

Lev: Yeah, and for the particle diameter calculation using equation one twenty-six ten point zero zero three three four page one of that work reads Fluid drag on a sphere at finite Reynolds number--a classical problem examined afresh, you can easily calculate d star as a function of Re for all Reynolds numbers below nine hundred.

Mira: That's good because it means you don't have to change your entire model structure just because you move the Reynolds number slightly within that range.

Kai: So to wrap up, this paper on Fluid drags on a sphere at finite Reynolds number--a classical problem examined afresh shows that Klyachko’s formula has reasonable accuracy for Re less than or equal to one thousand and its extension up to three times ten five as a piecewise continuous function <ref:2610.00334#pg1,on a sphere at finite Reynolds number--a classical problem examined afresh>.

Mira: It also provides closed-form analytical solutions for rectilinear motion when gravity is ignored, which is useful for aerosol particles, and they demonstrate that the root-mean-square relative error from this formula is consistently lowest in the lower Reynolds number range compared to some newer correlation formulas.

Lev: And they show you can calculate the terminal settling velocity as functions of Re, and they have these demonstrations for acceleration and terminal velocity that align well with other relevant data from Wang and Pruppacher in one thousand nine hundred seventy-seven <ref:2610.00334#pg1>.

Kai: It’s a solid piece of work that takes a classical problem, checks its accuracy against modern methods, and shows how you can get analytical solutions for motion when you strip away some complexity like gravity.

Mira: It's a good way to study the classical problem of aerosol dynamics by providing tools that are both mathematically tractable and empirically validated in certain regimes.

The paper's summary: Kai: So we've been looking at how this study takes that old problem of drag on a sphere and looks at it again using Klyachko's formula. Now, let's just take a moment to look at their summary of what they actually did there.

Mira: Okay, so the core idea is they are testing if Klyachko’s one thousand nine hundred thirty-four formula works as well as the newer correlation formulas we use today when the Reynolds number gets bigger. They found that for low Reynolds numbers, say below a thousand, this older formula is actually quite accurate.

Lev: But Mira, what's the catch? What are they saying about those higher Reynolds numbers where things usually get messy?

Mira: They admit that while it's reasonable below a thousand and even extending up to three times ten five as a piecewise continuous function, the error starts to climb noticeably when you get into the drag crisis region. That's where things get tricky for aerosol dynamics.

Kai: So what does that actually mean for someone working on something like a simulation or an experimental setup?

Lev: It means if you're modeling something at high Reynolds numbers, you can't just plug in Klyachko’s formula and expect perfect results; you need to be careful about where the pieces of the function change.

Mira: Exactly. The paper uses this Klyachko formula to derive a closed-form analytical solution for how a sphere accelerates when gravity is ignored, which is useful for aerosol particles that aren't falling under gravity anyway.

Kai: That's neat, getting an analytical solution instead of just some curve you have to fit to experimental data.

Lev: It’s useful because you get a function of time directly, like how fast the velocity changes with time, rather than having to calculate it through some complex integral every single step.

Mira: And they also show how you can use this formula to calculate things like the particle diameter and the terminal settling velocity based on force balance using a given drag coefficient.

Kai: So, in short, they've shown that this classic formula is reliable enough for many practical applications in aerosol studies as long as you stay below a thousand Reynolds number or be smart about how you use the extension.

Lev: It bridges the gap between the old theory and what we need for modern simulations because it gives us a way to get an exact solution where other methods might just give you an approximation.

Mira: And that accuracy is consistent with comparing it against newer correlation formulas, especially when you look at those lower Reynolds number regimes.

Kai: It’s a good piece of work for taking this classical problem and showing it still has analytical potential for motion modeling.

Lev: It sets a benchmark for how these older equations can still be useful tools in the toolkit, even if they aren't the most sophisticated correlation formulas available today.

The paper's improvements: Tom: So we've talked about how this study tests Klyachko’s formula for accuracy, but now let's look at what they suggest improving about the original problem description itself.

Kai: The paper points out that while the core math is classical, it needs to be framed in a way that helps with these new analytical solutions, especially when you try to apply it to things like aerosol particles.

Mira: They suggest focusing on how you handle those specific parameter choices in the Klyachko formula—those two common fractions they used as fitting parameters—because that's what actually unlocks the closed-form integration for rectilinear motion.

Lev: I mean, from a hardware standpoint, if you can get an analytical solution for acceleration instead of just relying on numerical integration over time, that’s a huge reduction in computational overhead.

Kai: Right, it means you can solve the differential equations directly rather than running a lot of iterative steps to find the velocity at every tiny moment.

Mira: They are basically saying that by simplifying the way we set up those initial conditions and how we choose our fitting constants, we can make this classical problem much more tractable for real-world modeling.

Lev: That’s what I need; if it simplifies the dynamics, it means your error correction routines won't have to work as hard to keep up with the physics.

Kai: It seems they aren't trying to reinvent fluid dynamics, just making sure that when we use these old equations for things like aerosol trajectories, we’re using the best possible mathematical framework available.

Mira: Exactly. The implication is that this isn't just a historical curiosity; it’s a validated tool for deriving analytical solutions for motion problems where gravity is ignored or simplified.

Lev: And they show how you can then use those derived functions to calculate things like the particle diameter and terminal settling velocity as simple functions of the Reynolds number.

Kai: So, the main suggestion is to refine the mathematical structure around Klyachko’s work so it smoothly connects with these new analytical frameworks.

Mira: And that refinement is what allows them to demonstrate those good agreements with more sophisticated correlation formulas in specific ranges.

Lev: It's about building a bridge between the old, established equations and the modern, high-fidelity data fitting methods.

Conclusion: Kai: So we’ve covered how this study tests Klyachko’s formula for accuracy and looks at what they suggest improving about the original problem description itself. Now, let's look at their final summary of what they actually found there.

Mira: They basically conclude that the extended Klyachko formula is quite reliable for low Reynolds numbers, meaning below a thousand, and it can be extended as a piecewise continuous function up to three times ten five.

Lev: That means for anyone building hardware or running simulations in that lower range, you have a pretty solid analytical tool to rely on.

Kai: They also highlighted that the root-mean-square relative error from this formula is consistently the lowest compared to some newer correlation formulas in those lower Reynolds number ranges.

Mira: That’s important because it shows this classical approach still has real predictive power when you stick to those specific conditions.

Lev: I need to hear that they can derive closed-form analytical solutions for rectilinear motion when gravity is ignored, especially for aerosol particles.

Kai: And they do, which is a big deal because it lets you solve the differential equations directly instead of running many iterative steps.

Mira: They also showed you how to calculate the particle diameter and terminal settling velocity as functions of Reynolds number using force balance equations.

Lev: So, for someone building a model, it’s useful because these derived functions give you concrete results for those physical quantities based on the Reynolds number input.

Kai: It seems like the big implication is that this paper validates using Klyachko's formula as a reliable starting point for motion modeling in aerosol dynamics within its defined limits.

Mira: And it gives us a way to get analytical solutions for acceleration that are comparable to other relevant data, like what Wang and Pruppacher found in one thousand nine hundred seventy-seven.

Lev: It’s good validation because it links this old Russian paper to current results in the field, giving us more confidence in using these types of equations.

Kai: So, the final word on this paper is that it gives us a mathematically tractable way to study aerosol dynamics by providing tools that are both accurate and analytical.

Mira: It’s a good reminder that classical problems still have significant utility when you look at them through the lens of modern error analysis.

Lev: It shows how much useful physics you can extract from these foundational equations even when you strip away complexities like gravity.

OXCBO Research

physics.flu-dyn

Submitted: 2026-09-29

Updated: 2026-11-15

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 77/100

The gist: Evaluating the drag coefficient Cd for a sphere moving in a fluid at finite Reynolds number Re has become a classical research subject in fluid dynamics…

Key concepts

Drag Coefficient (Cd)
This measures the resistance a fluid exerts on a sphere moving through it. It is crucial in fluid dynamics because it dictates how much force is needed to move the object at a certain speed, and its value changes significantly as the flow speed (Reynolds number) increases.
Reynolds Number (Re)
Re is a dimensionless number that represents the ratio of inertial forces to viscous forces in a fluid. It tells scientists whether fluid motion will be smooth or turbulent, which directly affects how much drag a sphere experiences at high speeds.
Rectilinear Motion
This refers to the straight-line movement of an object, like an aerosol sphere falling through air. The paper seeks analytical solutions for this motion under simplified conditions where only drag is the primary force acting on the particle.

Terminology

Summary

Evaluating the drag coefficient Cd for a sphere moving in a fluid at finite Reynolds number Re has become a classical research subject in fluid dynamics, with publications appearing continuously by numerous authors over the years due to the unavailability of closed-form mathematical solutions To date, mathematical formulas for calculating Cd as a function of Re can only be obtained by correlation curve-fitting to experimental data The present study focuses on examining the accuracy of Klyachko’s 1934 formula for Cd(Re) with two common fractions as fitting parameters, which could enable closed-form integration of a simplified equation governing rectilinear motion of aerosol spheres The computed values of root-mean-square relative error from recently developed formulas show reasonable accuracy of the Klyachko formula for Re ≤ 1000 and its extension to Re < 3 × 10 5 as a piecewise continuous function Hence, a few demonstrative examples are presented using the extended Klyachko formula in the study of rectilinear acceleration, the calculation of the terminal velocity of aerosol spheres, and so forth, to shed fresh light on how this classical problem can be studied. p. 0

Where the paper says it

The present study focuses on examining the accuracy of Klyachko’s 1934 formula for Cd(Re) with two common fractions as fitting parameters, which could enable closed-form integration of a simplified equation governing rectilinear motion of aerosol spheres. The computed values of root-mean-square relative error from recently developed formulas show reasonable accuracy of the Klyachko formula for Re ≤ 1000 and its extension to Re < 3 × 105 as a piecewise continuous function, with the possibility of significant improvement through a slight modification.

Pruning redundant reasoning tokens

The paper addresses the long-standing issue where closed-form analytical solutions for flow around rigid and fluid spheres are limited to very low values of the Reynolds number Knowledge about the situation at higher Reynolds numbers must resort to experimental measurements, numerical computations, as well as approximations based on boundary-layer theory The drag coefficient Cd is often presented as a graph versus Re known as the ”Rayleigh curve” or “standard drag curve” (Clift, Grace, and Weber, 1978). Despite tremendous efforts by generations after generations of mathematically talented scientists, closed-form analytical solutions for flow around rigid and fluid spheres are effectively limited to very low values of the Reynolds number. p. 1

Where the paper says it

Besides its theoretical convenience for the in-depth mathematical study of drag, boundary layer separation, and turbulence, the problem of a spherical body moving in a fluid often appears in a myriad of natural processes and engineering applications (Fuchs, 1964; Clift, Grace, and Weber, 1978; Pruppacher and Klett, 1997). Despite the tremendous efforts by generations after generations of mathematically talented scientists, closed-form analytical solutions for flow around rigid and fluid spheres are effectively limited to very low values of the Reynolds number, Re ≡ ud/ν (where d denotes the sphere’s diameter, u and ν the relative velocity and kinematic viscosity of the surrounding fluid).

Comparison of Cd(Re) with a reference formula

The study compares the extended Klyachko formula (1) with recently developed correlation formulas, such as those by Brown and Lawler (2003) or others, using the root-mean-square relative error (RMSRE) Table 1 presents the values of RMSRE (2) with f(x) for the Cd(Re) in (1) and the reference function F(x) for the correlation formulas by recent authors, integrated from Re = 0.01 to Re = 1000, 900, 800, and 500 as well as Re = 10 cubed to Re = 2 × 10 5 Apparently, for the interval of Rem ≤ Re < Rem where Rem is chosen as 900 in the modified formula (3), the RMSRE values are consistently lowest for (1) versus the correlation formula of Cheng (2009). p. 4

Where the paper says it

01 < Re < 1000, the RMSRE value is consistently lowest for (1) versus the correlation formula of Cheng (2009), while the differences between (1) and all three correlation formulas of Brown and Lawler (2003), Cheng (2009), and Barati, Neyshabouri, and Ahmadi (2014) have RMSRE values less than 5%. Most of the differences appear to come from the interval of 800 < Re < 1000.

However, for 10 cubed < Re < 2 × 10 5, the RMSRE values for Cd = 0. p. 4
Where the paper says it

2 Comparison of Cd(Re) with a reference formula To measure the difference (or “error”) between the extended Klyachko formula (1) and a recently developed correlation formula, such as that of Brown and Lawler (2003) or others, the root-mean-square relative error (RMSRE): RMSRE = s 1 b − a Z b a f(x) − F(x) F(x) 2 dx , (2) is used here, where f(x) denotes the test function and F(x) the reference function. Table 1 presents the values of RMSRE (2) with f(x) for the Cd(Re) in (1) and the reference function F(x) for the correlation formulas by recent authors (Brown and Lawler, 2003; Cheng, 2009; Barati, Neyshabouri, and Ahmadi, 2014), integrated from Re = 0.

424 versus those of the sophisticated correlation formulas are slightly over 10%, coming mostly from the interval of Rem = 900 ≤ Re < 3 × 10 5 (as Cd approaches the so-called drag crisis). p. 4
Where the paper says it

424 versus those of the sophisticated correlation formulas are slightly over 10%, coming mostly from the interval of 105 < Re < 2 × 105 (as Cd approaches the so-called drag crisis). It should be noted that table 1 also reveals the fact that a significant reduction of the RMSRE values can be achieved by simply moving the upper limit of the Klyachko formula in (1) from Rem = 1000 to 900, for a modified formula with improved accuracy (espectially for Re > 1000 up to Re ∼ 3 × 105 ), Cd(Re) =    24 Re 1 + 1 6 Re2/3 , for 0 < Re < Rem = 900 4(6 + Re2/3 m )/Rem ≈ 0.

Particle rectlinear acceleration

The paper derives equations for the rectilinear motion of a spherical particle under quasistatic drag as the only dominant force controlling its motion For the case of quasistatic drag as the only dominant force controlling the rectilinear motion of a spherical particle (with particle density ρp and velocity u(t)), Newton’s law of motion based on Eq. (1) can be written as du˜dt˜=−3ρ(6+Re 2/3m)ρp/Remu 2≈0. p. 6

Where the paper says it

Re Dra g C o efficie nt Figure 1: Graphic comparison between Eq. (1) and more recent correlation formulas for drag coefficient (Brown and Lawler, 2003; Barati, Neyshabouri, and Ahmadi, 2014) on (3) for the “initial particle Reynolds number” Re0 ≡ u(0)d/ν < 3 × 105 can be written as du˜ dt˜ =    − 3ρ(6+Re 2/3 m ) ρp Rem u˜ 2 ≈ 0.

331ρ/ρp u squared, for 900 ≤ Re0u Rem = 900, a straightforward integration of (4a) for u˜(0) = 1 yields u˜(t˜)=1+0. p. 6
Where the paper says it

For the case of Re0 > Rem = 900, a straightforward integration of (4a) for u˜(0) = 1 yields u˜(t˜) = 1 + 0. 331ρ ρp t˜ −1 , for t˜≤ t˜m = ρp 0.

331ρ/ρp t˜−1, for t˜≤ t˜m=ρp/0. p. 6
Where the paper says it

(1) and more recent correlation formulas for drag coefficient (Brown and Lawler, 2003; Barati, Neyshabouri, and Ahmadi, 2014) on (3) for the “initial particle Reynolds number” Re0 ≡ u(0)d/ν < 3 × 105 can be written as du˜ dt˜ =    − 3ρ(6+Re 2/3 m ) ρp Rem u˜ 2 ≈ 0. 331ρ ρp u˜ 2 , for 900 ≤ Re0u <˜ 3 × 105 , − 18 ρ Re0 ρp 1 + Re 2/3 0 6 u˜ 2/3 !

331ρ Re0−Rem/Rem. p. 6
Where the paper says it

(1) and more recent correlation formulas for drag coefficient (Brown and Lawler, 2003; Barati, Neyshabouri, and Ahmadi, 2014) on (3) for the “initial particle Reynolds number” Re0 ≡ u(0)d/ν < 3 × 105 can be written as du˜ dt˜ =    − 3ρ(6+Re 2/3 m ) ρp Rem u˜ 2 ≈ 0. 331ρ ρp u˜ 2 , for 900 ≤ Re0u <˜ 3 × 105 , − 18 ρ Re0 ρp 1 + Re 2/3 0 6 u˜ 2/3 !

Then, for t >˜t̃m, it turns out that (4b) can be rearranged as d/u 2/3 dt˜=12 ρRe0 ρp u-2/3+Re 2/3m, which yields an analytical solution for u˜(t̃)<u˜(t̃m)=Rem/Re0, similar to that shown by Serafini (1954) and Putnam (1961). p. 6
Where the paper says it

(5) Then, for t >˜ t˜m, it turns out (though may not be immediately obvious) that (4b) can be rearranged as d u˜ −2/3 dt˜ = 12 ρ Re0 ρp u˜ −2/3 + Re 2/3 0 6 ! , which yields an analytical solution for u˜(t˜) < u˜(t˜m) = Rem/Re0, similar to that shown by

Particle terminal settling velocity

With a given Cd(Re) for a sphere moving in a fluid, the terminal velocity u of a spherical particle with density ρp settling under the influence of gravity can be readily calculated based on force balance The relationship is expressed as 3Re 2Cd/4=d 3g/(ρp-1) or 3Re 2Cd/4=d 3gν-2/(ρp-1), where g denotes gravitational acceleration. If the particle diameter and velocity are nondimensionalized as d∗ = d gν-2 ρp/ρ−1 1/3=3CdRe 2/4 1/3 and u∗ = u gν / (ρp-1-1/3=4Re 3Cd 1/3, we have u∗ × d∗ = Re as suggested by Brown and Lawler (2003). p. 8

Where the paper says it

Noteworthy here is that 3Re2Cd/4 is the Archimedes number (also called the Best number), while Re2Cd is known as the Davies number, often used by atmospheric scientists in studying the terminal velocity of water droplets in air (Davies, 1945; Beard, 1976). If the particle diameter and velocity are nondimensionalized as d ∗ = d g ν 2 ρp ρ − 1 1/3 = 3CdRe2 4 1/3 and (11a) u ∗ = u gν ρp ρ − 1 −1/3 = 4Re 3Cd 1/3 , (11b) we have u ∗ × d ∗ = Re as suggested by Brown and Lawler (2003).

With Cd given by (1) or (3), d∗ and u∗ can be easily calculated as functions of Re, as d∗(Re)=Re 18+3Re 2/3 1/3, for 0 < Re < Rem and then u∗(Re)=Re/d∗(Re). p. 9
Where the paper says it

With Cd given by (1) or (3), d ∗ and u ∗ can be easily calcultated as functions of Re, as d ∗ (Re) =    Re 18 + 3Re2/3 1/3 , for 0 < Re < Rem 18+3Re 2/3 m Rem 1/3 Re2/3 , for Rem ≤ Re < 3 × 105 , andthen u ∗ (Re) = Re/d∗ (Re) , (12) where we have Rem = 1000 for (1), if so chosen, and Rem = 900 for (3). However, most authors present curve-fitting formulas for directly calculting the terminal velocity from a given particle size, namely, u ∗ (d ∗ ) (Brown and Lawler, 2003; Cheng, 2009).

Where the gains come from

The primary contribution of this work is to quantitatively understand how good (or bad) the extended Klyachko formula can be for practical applications, showing that it exhibits reasonable accuracy for Re < 1000 or better yet, Re < 900. This accuracy is demonstrated by comparing it with more recent correlation formulas, where RMSRE values are consistently lowest in the lower Reynolds number range and acceptable for practical real-world applications especially for Re < 1000. p. 5

Where the paper says it

Thus, the accuracy of (3) can be quite acceptable. In view of numerical differences among various available correlation formulas and the noisiness of experimental data, the comparison between (1) and recently developed “more accurate” correlation formulas appears quite reasonable for practical real-world applications, especially for Re < 1000.

Furthermore, the extended Klyachko formula enables the derivation of closed-form analytical solutions to govern rectilinear acceleration when gravity is ignored, which is useful for aerosol particles. p. 3
Where the paper says it

The mathematical function of (1) for 0 < Re < 1000, though significantly nonlinear, was shown to enable the derivation of a closed-form analytical solution to the differential equation governing the rectilinear motion of a sphere in a fluid (Serafini, 1954; Putnam, 1961), when forces other than the drag are negligible, such as situations often encountered with aerosol particles (Fuchs, 1964). A closed-form analytical solution in fluid dynamics of a moving sphere is generally considered intractable, and highly appreciated for its mathematical elegance even though it is useful only for special circumstances in a limited interval of Re values.

Summary

The results indicate quantitatively rather insignificant differences between the extended Klyachko formula Cd(Re) and other apparently more sophisticated correlation formulas for Re < 1000 (or, better yet, for Re < 900). Once the confidence is established for its reasonable accuracy, the extended Klyko formula Cd(Re) is briefly shown to yield closedform analytical solutions covering the applicable range of 0 < Re < 3 × 10 5 for the study of rectilinear acceleration of aerosol spheres when gravity can be ignored. p. 0

Where the paper says it

The computed values of root-mean-square relative error from recently developed formulas show reasonable accuracy of the Klyachko formula for Re ≤ 1000 and its extension to Re < 3 × 105 as a piecewise continuous function, with the possibility of significant improvement through a slight modification. Hence, a few demonstrative examples are presented using the extended Klyachko formula in the study of rectilinear acceleration, the calculation of the terminal velocity of aerosol spheres, and so forth, to shed fresh light on how this classical problem can be studied.

Then, a demonstration of using the extended Klyko formula is presented for conveniently calculating the spherical particle diameter and terminal settling velocity as functions of Re, yielding results in good agreement with recent correlation formulas of Brown and Lawler (2003) and Cheng (2009). p. 9
Where the paper says it

Table 2 and figure 2 exemplify tabulated values of d ∗ , u ∗ generated based on (12) for Rem = 1000 in comparison with the correlation formulas of Brown and Lawler (2003) and Cheng (2009), and the corresponding graph of u ∗ versus d ∗ . Again not surpringly, the results of d ∗ (Re) given by (12) for Rem = 1000, based on as a slightly less accurate Cd(Re) formula (1), are still in reasonable agreement with those of more recent correlation formulas.

As expected, the dynamical process of an aerosol sphere accelerating toward its terminal velocity can also be described by solutions of ordinary differential equations based on the extended Klyko formula, with comparable results to such relevant data of Wang and Pruppacher (1977) for water droplet falling in air when droplet deformations are negligible. p. 9
Where the paper says it

Again not surpringly, the results of d ∗ (Re) given by (12) for Rem = 1000, based on as a slightly less accurate Cd(Re) formula (1), are still in reasonable agreement with those of more recent correlation formulas. One of the most studied cases of terminal velocity is a water droplet falling in air, with 1

These demonstrative examples are expected to enhance confidence in the extended Klyachko formula for conveniently studying the classical problem of aerosol (sphere) dynamics, among other applications. p. 0
Where the paper says it

Hence, a few demonstrative examples are presented using the extended Klyachko formula in the study of rectilinear acceleration, the calculation of the terminal velocity of aerosol spheres, and so forth, to shed fresh light on how this classical problem can be studied. Keywords: Sphere in fluid, drag coefficient, correlation formula, extended Klyachko formula, accuracy comparison, rectilinear motion 1 arXiv:2610.

The derived closed-form analytical formulas can also be applied in modern CFD code development and validation. p. 7
Where the paper says it

(In other words, the formula of Schiller and Naumann (1933), though very similar to that of Klyachko in mathematical form but with an exponent β slightly deviating from 2/3, cannot facilitate a closed-form integration in a rigorous sense. ) By integrating u˜(t˜) given by (5) from 0 to t˜(if t˜≤ t˜m for Re0 > Rem) and (6) from t˜m to t˜ (when t >˜ t˜m), the particle flight distance (in units of d) as a function of flight time can also be derived as z˜(t˜) =    ρp 0.

Acknowledgments

The author would like to thank Prof. Rodney Kubesh (of St. Cloud State University) for helpful discussions and Prof. Carlos Ramírez (of University of Puerto Rico) for providing a copy of the original 1934 Russian article by Klyachko. p. 0

Where the paper says it

The consequence is the coexistence of various formulas with different mathematical fitting functions and an increasing number of fitting parameters. The present study focuses on examining the accuracy of Klyachko’s 1934 formula for Cd(Re) with two common fractions as fitting parameters, which could enable closed-form integration of a simplified equation governing rectilinear motion of aerosol spheres.

Funding

None

Ethics declarations

The author has no conflicts to declare

ORCID iD

James Q Feng 0000-0003-4041-3179

References

Amsden, A A, P J O’Rourke, and T D Butler (1989). KIVA-II: A computer program for chemically reactive flos with sprays. p. 3

Where the paper says it

What has been implemented in the computational fluid dynamics (CFD) software package OpenFOAM® for the “sphere drag” calculation is in terms of a piecewise continuous function Cd(Re) =    24 Re 1 + 1 6Re2/3 , for 0 < Re < Rem = 1000 24 Rem 1 + 1 6Re2/3 m = 0. 424 , for Re ≥ Rem = 1000 , (1) following the KIVA-II work of Amsden, O’Rourke, and Butler (1989) (which would actually be invalid beyond Re ∼ 3 × 105 when the abrupt “drag crisis” occurs).

Tech. rep. LA-11560-MS; ON: DE89012805. Los Alamos National Lab

Beard, K V (1976). “Terminal velocity and shape of cloud and precipation drops aloft”. p. 0

Where the paper says it

The computed values of root-mean-square relative error from recently developed formulas show reasonable accuracy of the Klyachko formula for Re ≤ 1000 and its extension to Re < 3 × 105 as a piecewise continuous function, with the possibility of significant improvement through a slight modification. Hence, a few demonstrative examples are presented using the extended Klyachko formula in the study of rectilinear acceleration, the calculation of the terminal velocity of aerosol spheres, and so forth, to shed fresh light on how this classical problem can be studied.

J. Atmos. Sci. 33.5, pp. 851–864

Brown, P P and D F Lawler (2003). “Sphere drag and setting velocity revisited”. p. 0

Where the paper says it

Hence, a few demonstrative examples are presented using the extended Klyachko formula in the study of rectilinear acceleration, the calculation of the terminal velocity of aerosol spheres, and so forth, to shed fresh light on how this classical problem can be studied. Keywords: Sphere in fluid, drag coefficient, correlation formula, extended Klyachko formula, accuracy comparison, rectilinear motion 1 arXiv:2610.

J. Environ. Eng. 129.3, pp. 222–231

Cheng, N-S (2009). “Comparison of formulas for drag coefficient and settling velocity of spherical particles”. p. 8

Where the paper says it

, the terminal velocity due to gravity is much smaller than the sphere velocity magnitude of interest, as in the study of dust particles in dust-recollecting devices (Klyachko, 1934), droplet impingement onto an airfoil (Serafini, 1954), fuel droplet spray in a combustion chamber (Putnam, 1961; Amsden, O’Rourke, and Butler, 1989), among others. 4 Particle terminal settling velocity With a given Cd(Re) for a sphere moving in a fluid, the terminal velocity u of a spherical particle with density ρp settling under the influence of gravity can be readily calculated based on force balance: πd2ρu2Cd 8 = πd3 (ρp − ρ)g 6 or 3Re2Cd 4 = d 3 g ν 2 ρp ρ − 1 , (10) where g denotes gravitational acceleration.

Powder Technol. 189, pp. 395–398

Clift, R, J R Grace, and M E Weber (1978). Bubbles, Drops, and Particles

Davies, C D (1945). “Definitive equations for fluid resistance of spheres”. p. 0

Where the paper says it

Hence, a few demonstrative examples are presented using the extended Klyachko formula in the study of rectilinear acceleration, the calculation of the terminal velocity of aerosol spheres, and so forth, to shed fresh light on how this classical problem can be studied. Keywords: Sphere in fluid, drag coefficient, correlation formula, extended Klyachko formula, accuracy comparison, rectilinear motion 1 arXiv:2610.

Proc. Phys. Soc. London A57.4, pp. 259–270

Fuchs, N A (1964). The Mechanics of Aerosols

Goossens, W R A (2019). “Review of the empirical correlations for the drag coefficient of rigid spheres”. p. 1

Where the paper says it

Besides its theoretical convenience for the in-depth mathematical study of drag, boundary layer separation, and turbulence, the problem of a spherical body moving in a fluid often appears in a myriad of natural processes and engineering applications (Fuchs, 1964; Clift, Grace, and Weber, 1978; Pruppacher and Klett, 1997). Despite the tremendous efforts by generations after generations of mathematically talented scientists, closed-form analytical solutions for flow around rigid and fluid spheres are effectively limited to very low values of the Reynolds number, Re ≡ ud/ν (where d denotes the sphere’s diameter, u and ν the relative velocity and kinematic viscosity of the surrounding fluid).

Chemical Engineering Science 168, pp. p. 1
Where the paper says it

1 Introduction As a fundamental canonical problem in fluid mechanics, flow past a sphere has been studied by numerous authors and discussed in well-known subject-matter books (Lamb, 1932; Schlichting, 1955; Landau and Lifshitz, 1959; Fuchs, 1964; Clift, Grace, and Weber, 1978; Pruppacher and Klett, 1997). Besides its theoretical convenience for the in-depth mathematical study of drag, boundary layer separation, and turbulence, the problem of a spherical body moving in a fluid often appears in a myriad of natural processes and engineering applications (Fuchs, 1964; Clift, Grace, and Weber, 1978; Pruppacher and Klett, 1997).

339–343

Gunn, R and G D Kinzer (1949). “The terminal velocity of fall for water droplets in stagnant air”. p. 8

Where the paper says it

4 Particle terminal settling velocity With a given Cd(Re) for a sphere moving in a fluid, the terminal velocity u of a spherical particle with density ρp settling under the influence of gravity can be readily calculated based on force balance: πd2ρu2Cd 8 = πd3 (ρp − ρ)g 6 or 3Re2Cd 4 = d 3 g ν 2 ρp ρ − 1 , (10) where g denotes gravitational acceleration. Noteworthy here is that 3Re2Cd/4 is the Archimedes number (also called the Best number), while Re2Cd is known as the Davies number, often used by atmospheric scientists in studying the terminal velocity of water droplets in air (Davies, 1945; Beard, 1976).

Journal of Meteorology 6, pp. 243–248

Hasadi, Y M F El and J T Padding (2023). “Do logarithmic terms exist in the drag coefficient of a single sphere at high Reynolds numbers? p. 1

Where the paper says it

Knowledge about the situation at higher Reynolds numbers must resort to experimental measurements, numerical computations, as well as approximations based on boundary-layer theory (Clift, Grace, and Weber, 1978). Dictated by the laws of physics, a sphere (or any object of another shape) will experience a drag force—as the surface integral over its whole surface of all stresses arising from the relative fluid flow—whenever there is a relative motion of it in the surrounding fluid (Landau and Lifshitz, 1959).

” Chemical Engineering Science 168, p. p. 1
Where the paper says it

1 Introduction As a fundamental canonical problem in fluid mechanics, flow past a sphere has been studied by numerous authors and discussed in well-known subject-matter books (Lamb, 1932; Schlichting, 1955; Landau and Lifshitz, 1959; Fuchs, 1964; Clift, Grace, and Weber, 1978; Pruppacher and Klett, 1997). Besides its theoretical convenience for the in-depth mathematical study of drag, boundary layer separation, and turbulence, the problem of a spherical body moving in a fluid often appears in a myriad of natural processes and engineering applications (Fuchs, 1964; Clift, Grace, and Weber, 1978; Pruppacher and Klett, 1997).

118195

Klyachko, L S (1934). “Equations of motion of dust particles in dust-collecting devices”

Kramer, O J I, P J de Moel, S K R Raaghav, E T Baars, W H van Vugt, W-P Breugem, J T Padding, and J P van der Hoek (2021). “Can terminal settling velocity and drag of natural particles in water ever be predicted accurately? p. 8

Where the paper says it

, the terminal velocity due to gravity is much smaller than the sphere velocity magnitude of interest, as in the study of dust particles in dust-recollecting devices (Klyachko, 1934), droplet impingement onto an airfoil (Serafini, 1954), fuel droplet spray in a combustion chamber (Putnam, 1961; Amsden, O’Rourke, and Butler, 1989), among others. 4 Particle terminal settling velocity With a given Cd(Re) for a sphere moving in a fluid, the terminal velocity u of a spherical particle with density ρp settling under the influence of gravity can be readily calculated based on force balance: πd2ρu2Cd 8 = πd3 (ρp − ρ)g 6 or 3Re2Cd 4 = d 3 g ν 2 ρp ρ − 1 , (10) where g denotes gravitational acceleration.

” Drinking Water Engineering and Science 14. p. 1
Where the paper says it

1 Introduction As a fundamental canonical problem in fluid mechanics, flow past a sphere has been studied by numerous authors and discussed in well-known subject-matter books (Lamb, 1932; Schlichting, 1955; Landau and Lifshitz, 1959; Fuchs, 1964; Clift, Grace, and Weber, 1978; Pruppacher and Klett, 1997). Besides its theoretical convenience for the in-depth mathematical study of drag, boundary layer separation, and turbulence, the problem of a spherical body moving in a fluid often appears in a myriad of natural processes and engineering applications (Fuchs, 1964; Clift, Grace, and Weber, 1978; Pruppacher and Klett, 1997).

1

Lamb, H (1932). Hydrodynamics (6th Edition)

Landau, L D and E M Lifshitz (1959). Fluid Mechanics

Lapple, C E and C B Shepherd (1940). “Calculation of Particle Trajectories”

Michaelides, E E (2026). “The equation of motion of particles in fluids—An historical perspective”

Pruppacher, H R and J D Klett (1997). Microphysics of Clouds and Precipitation (revised and enlarged edition)

Putnam, A (1961). “Integratable form of droplet drag coefficient”

Ramirez, C A (2017). “Summary of frictional drag coefficient relationships for spheres: Evolving solution strategies applied to an old problem” Chem. p. 0

Where the paper says it

Hence, a few demonstrative examples are presented using the extended Klyachko formula in the study of rectilinear acceleration, the calculation of the terminal velocity of aerosol spheres, and so forth, to shed fresh light on how this classical problem can be studied. Keywords: Sphere in fluid, drag coefficient, correlation formula, extended Klyachko formula, accuracy comparison, rectilinear motion 1 arXiv:2610.

Eng. Sci. 168, pp. 339–343

Schiller, L and A Naumann (1933). “Uber die grundlegenden Berechnungen bei der Schw-erkraftaufbereitung (On the fundamental calculations in gravity separation)”

Schlichting, H (1955). Boundary-Layer Theory

Serafini, J S (1954). Impingement of water droplets on wedges and double-wedge airfoils at supersonic speeds. p. 8

Where the paper says it

4 Particle terminal settling velocity With a given Cd(Re) for a sphere moving in a fluid, the terminal velocity u of a spherical particle with density ρp settling under the influence of gravity can be readily calculated based on force balance: πd2ρu2Cd 8 = πd3 (ρp − ρ)g 6 or 3Re2Cd 4 = d 3 g ν 2 ρp ρ − 1 , (10) where g denotes gravitational acceleration. Noteworthy here is that 3Re2Cd/4 is the Archimedes number (also called the Best number), while Re2Cd is known as the Davies number, often used by atmospheric scientists in studying the terminal velocity of water droplets in air (Davies, 1945; Beard, 1976).

Tech. rep. NASA-TP-1159

Wang, P K and H R Pruppacher (1977). “Acceleration to terminal velocity of cloud and raindrops” J. p. 0

Where the paper says it

The computed values of root-mean-square relative error from recently developed formulas show reasonable accuracy of the Klyachko formula for Re ≤ 1000 and its extension to Re < 3 × 105 as a piecewise continuous function, with the possibility of significant improvement through a slight modification. Hence, a few demonstrative examples are presented using the extended Klyachko formula in the study of rectilinear acceleration, the calculation of the terminal velocity of aerosol spheres, and so forth, to shed fresh light on how this classical problem can be studied.

Appl. Meteor. 16

Zigrang, D J and N D Sylvester (1981). “An explicit equation for particle settling velocities in solid-liquid systems” AIChE J. p. 8

Where the paper says it

, the terminal velocity due to gravity is much smaller than the sphere velocity magnitude of interest, as in the study of dust particles in dust-recollecting devices (Klyachko, 1934), droplet impingement onto an airfoil (Serafini, 1954), fuel droplet spray in a combustion chamber (Putnam, 1961; Amsden, O’Rourke, and Butler, 1989), among others. 4 Particle terminal settling velocity With a given Cd(Re) for a sphere moving in a fluid, the terminal velocity u of a spherical particle with density ρp settling under the influence of gravity can be readily calculated based on force balance: πd2ρu2Cd 8 = πd3 (ρp − ρ)g 6 or 3Re2Cd 4 = d 3 g ν 2 ρp ρ − 1 , (10) where g denotes gravitational acceleration.

27.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved drag coefficient prediction for aerosol spheres: The AI system can now calculate root-mean-square relative error (RMSRE) between Klyachko's extended formula and modern correlation formulas to quantitatively determine if a simplified piecewise continuous function, like equation (3), provides "reasonable accuracy of the Klyachko formula for Re <= 1000."

  2. Closed-form analytical solution derivation: The system can derive a closed-form analytical solution to the differential equation governing the rectilinear motion of a sphere in a fluid when forces other than drag are negligible, specifically for situations often encountered with aerosol particles.

  3. Terminal settling velocity calculation: The AI can calculate the particle terminal velocity u based on force balance using equation (10), and determine the non-dimensional parameters d star and u star as functions of Re using equation (12).

  4. Predictive modeling for particle motion: The system can predict the flight distance (in units of d) as a function of flight time by integrating the derived analytical solutions, providing results for z(t) that agree well with experimental data like those from Gunn and Kinzer (1949).

  5. High-accuracy terminal velocity estimation: By using equation (17), the system can calculate the stop distance (or the maximum achievable flight distance) z infinity, which is useful for evaluating the required free fall length in an experimental setup.

Abstract

Evaluating the drag coefficient Cd for a sphere moving in a fluid at finite Reynolds number Re has become a classical research subject in fluid dynamics, with publications appearing continuously by numerous authors over the years due to the unavailability of closed-form mathematical solutions. To date, mathematical formulas for calculating Cd as a function of Re can only be obtained by correlation curve fitting to experimental data. The consequence is the coexistence of various formulas with different mathematical fitting functions and an increasing number of fitting parameters. The present study focuses on examining the accuracy of Klyachko's 1934 formula for Cd with two common fractions as fitting parameters, which could enable closed form integration of a simplified equation governing rectilinear motion of aerosol spheres. The computed values of root-mean-square relative error from recently developed formulas show reasonable accuracy of the Klyachko formula for Re less than 1000 and its extension to Re less than 2e5 as a piecewise continuous function, with the possibility of significant improvement through a slight modification. Hence, a few demonstrative examples are presented using the extended Klyachko formula in the study of rectilinear acceleration, the calculation of the terminal velocity of aerosol spheres, and so forth, to shed fresh light on how this classical problem can be studied.

Related papers