XPCS-Echo and broad relaxation measurements using a bunch-mode data acquisition scheme
Listen
Radio episode about this paper
Transcript
Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.
Kai: I'm Kai.
Mira: And I'm Mira, here with Lev.
Kai: We're looking at the paper: "XPCS-Echo and broad relaxation measurements using a bunch-mode data acquisition scheme".
Paper summary: Mira: So, wrapping up this paper "XPCS-Echo and broad relaxation measurements using a bunch-mode data acquisition scheme", the main point is that by implementing the bunch-mode data acquisition scheme with an aperiodic Fibonacci sequence, they can probe nonaffine deformations and yielding behavior in soft viscoelastic materials under oscillatory shear using XPCS.
Kai: And they achieved this by overcoming the hardware constraints of conventional XPCS measurements, which usually limit the lag time tau you can sample in one shot by centering bunches at echo peaks > Page two <ref:2609.02645#pg1>.
Lev: So, what’s the big implication here for researchers who are trying to study complex soft matter? Are we actually looking at a way to get better data for those systems than we had before?
Mira: It means you can get much broader time scale access with less X-ray dose and less data volume than the old methods, which is especially useful when studying things like supercooled liquids or glasses > Page two <ref:2609.02645#pg1>.
Kai: And they confirm that this method can be extended beyond XPCS to other dynamic scattering methods like Differential Dynamic Microscopy or multispeckle DLS > Page two <ref:2609.02645#pg1>. The flexibility of bunch-mode acquisition might open up new possibilities for designing measurement schemes adapted to a broad range of dynamical processes > Page two <ref:2609.02645#pg1>.
Lev: That sounds promising because if you can adapt this core idea, it opens the door for designing customized measurement schemes for systems with very specific dynamic behaviors, like those exhibiting aging or nonstationary dynamics where bunches are triggered by real-time feedback from correlation statistics > Page two <ref:2609.02645#pg1>.
Kai: It’s about getting a much better view of what's happening in these materials under shear, using this new approach described in "XPCS-Echo and broad relaxation measurements using a bunch-mode data acquisition scheme" > Page one <ref:2609.02645#pg1,XPCS-Echo and broad relaxation measurements using a bunch-mode data acquisition>.
Conclusion: Kai: So we’ve seen how they used this bunch-mode approach to get these long time scales in XPCS measurements for soft materials under shear.
Mira: It basically means they’re using these echoes, those signals that come back when the sample moves periodically, to get a much wider window of time than before.
Kai: They really pushed the limits on how long they could observe without needing way more X-ray dose or massive amounts of data to cover that time range.
Lev: For us on real hardware, that reduction in data volume is huge because it means less storage and fewer complex processing steps to handle when we try to run these kinds of measurements.
Mira: The authors are showing that this method works for systems like supercooled liquids or gels where the dynamics are spread out over a very wide range of time scales.
Kai: It’s interesting how they used that Fibonacci sequence sampling to cover all those different time scales efficiently in one go, instead of having to take tons of separate measurements.
Lev: I do have to point out though, they admitted that this fast acquisition can be sparse when you’re looking at systems that relax really slowly or have nonergodic behavior.
Mira: Exactly, the paper notes they used a specific sequence because it seems to fit the ensemble averaging requirement for these particular gels they studied.
Kai: So the authors are claiming this bunch-mode acquisition is a way to quantitatively extract those dynamical parameters of how these materials deform under shear.
Lev: And what’s cool is that they showed you can actually get a solid analytical expression describing those echoes, which means you can use the data to calculate things directly.
Mira: It opens up a new toolkit for probing systems under small amplitude or low frequency oscillatory shear, which is something we haven't been able to do quite as well before with these techniques.
Kai: This protocol they used isn’t just for X-ray correlation spectroscopy; they suggest it can be adapted to other dynamic scattering methods too, like DDM or DLS.
Lev: That flexibility is a big deal because it means this concept isn't just stuck in one instrument; it could be a general way to sample dynamics across different types of setups.
European Synchrotron Radiation Facility (ESRF) · Laboratoire de Physique CNRS
cond-mat.soft
Submitted: 2026-09-02
Updated: 2026-11-17
Journal ref: Photon Science (2026)
DOI: 10.1021/photonsci.6c00073
License: http://arxiv.org/licenses/nonexclusive-distrib/1.0/
The gist: Echoes observed in the intensity-intensity autocorrelation functions [g2(q, τ)] is a powerful method for probing nonaffine deformations and yielding behavior of soft viscoelastic materials subjected…
Key concepts
- Intensity-Intensity Autocorrelation Function [g2(q, τ)]
- This function measures how the scattered X-ray intensity at a specific momentum (q) correlates with itself after a time delay (τ). In soft materials, observing echoes in this function reveals nonaffine deformations and the material's viscoelastic response to oscillatory shear.
- Bunch-Mode Data Acquisition
- This is a new data collection scheme where X-ray detector frames are centered around echo peaks, and bunches are placed in an aperiodic Fibonacci sequence. This method overcomes limitations of multispeckle measurements by allowing for long time spans with significantly fewer frames and lower X-ray dose.
- Nonaffine Deformations
- These refer to the local structural rearrangements or displacements within a material that are not simply uniform elastic deformations. In this context, the faster damping of echoes in g2(q, τ) is used to signify nonaffine contributions caused by oscillatory shear and eventual yielding.
Terminology
Summary
Echoes observed in the intensity-intensity autocorrelation functions [g2(q, τ)] is a powerful method for probing nonaffine deformations and yielding behavior of soft viscoelastic materials subjected to an oscillatory shear <ref:2609. p. 002645#pg2> The bunch-mode data acquisition scheme alleviates constraints imposed by multispeckle X-ray photon correlation spectroscopy (XPCS) measurements by implementing frames centered at echo peaks and placing bunches in an aperiodic Fibonacci sequence <ref:2609. p. 002645#pg9> This method allows for measuring g2(q, τ) over a long time span with orders of magnitude lesser number of frames <ref:2609. p. 002645#pg2>
Introduction to the XPCS-Echo Method
The light scattering-Echo (LS-Echo) method extends Photon Correlation Spectroscopy (PCS) to probe samples subjected to oscillatory motion or deformation <ref:2609.02645#pg2> For a perfectly elastic sample, periodic echoes can be observed in the intensity-intensity autocorrelation function [g2(q, τ)] that do not decay with time while the viscoelasticity is manifested by a gradual damping of echo peaks <ref:2609. p. 002645#pg2> The damping profile of the echo peaks contains information on nonaffine contributions such as that due to Brownian diffusion <ref:2609. p. 002645#pg2> XPCS can overcome the shortcomings of LS-Echo by allowing investigation of optically opaque samples and enabling multispeckle and direction-dependent analysis <ref:2609. p. 002645#pg2> The bunch-mode correlation method is distinct from those approaches involving multi-τ correlator and quasi-logarithmic time grid sampling <ref:2609. p. 102645#pg2>
Experimental Setup and Data Acquisition
The experiment utilized two colloidal systems: sterically-stabilized PMMA latex particles in cis-decalin and stearyl silica particles in n-dodecane, corresponding to repulsive colloidal glassy and attractive gel states <ref:2609.02645#pg3> The oscillatory shear was applied using a Haake RheoStress 6000 rheometer equipped with a capillary coaxial shear cell <ref:2609. p. 102645#pg2> XPCS measurements were conducted at the TRUSAXS instrument of the ESRF, covering a scattering vector range of 1. p. 17 × 10−3 nm−1 ≤ q ≤ 1 × 10−1 nm−1 <ref:2609. p. 002645#pg4> Bunch generation was achieved using the MAESTRIO device to gate the X-ray detector, with bunches centered around the maximum of the shear deformation γ <ref:2609. p. 102645#pg4>
Modeling Dynamical Contributions
The field-field autocorrelation function g1(q, τ)2 is modeled by factorizing contributions from Brownian diffusion, flow field effects, and decorrelation due to particle transit <ref:2609.02645#pg5> The Brownian motion term exhibits an exponential decay given by g1,D(q, τ)2 = exp−2Dq2τ <ref:2609. p. 302645#pg6> The flow field contribution is described by g1,F(t, τ)2 = sinc2h qπ cos(ψ)γLsinωt + ωτ/2 sinωτ/2 i <ref:2609. p. 302645#pg8> For higher shear rates and beam sizes, the term g1,T (q, τ) is important and given by g1,T (q, τ) = Z L0 exp −γ 2x squared sin2ωτ/2 σ 2y dx <ref:2609. p. 302645#pg9>
Results of the Bunch-Mode Acquisition
In XPCS-Echo measurements, echoes appear when the sample returns to its initial position due to periodic oscillatory motion <ref:2609.02645#pg2> The faster damping of echoes with increasing γ signifies nonaffine deformations induced by oscillatory shear and eventual yielding <ref:2609. p. 402645#pg2> For undamped echoes in a perfectly elastic sample, the bunch-mode acquisition significantly reduces the required number of frames while maintaining high time resolution <ref:2609. p. 502645#pg2> The aperiodic Fibonacci sequence was found to fulfill the requirement for sufficient temporal overlap in covering a broad range in lag time τ <ref:2609. p. 202645#pg4>
Conclusion and Future Directions
The bunch-mode acquisition colossally extends the accessible lag time range while significantly reducing the data volume and cumulative X-ray dose <ref:2609.02645#pg2> This approach is particularly well suited for systems exhibiting dynamics over a wide range of time scales like supercooled liquids, glasses and gels <ref:2609. p. 902645#pg2> Attention must be paid for ensuring an adequate level of ensemble averaging when determining the delays between the bunches <ref:2609. p. 902645#pg9> The protocol can be readily extended beyond XPCS to other dynamic scattering methods such as Differential Dynamic Microscopy (DDM) and multispeckle DLS <ref:2609. p. 902645#pg2> Adaptive bunch acquisition could be implemented for systems exhibiting aging or non-stationary dynamics where bunches are triggered based on real-time feedback from correlation statistics <ref:2609. p. 902645#pg2> The aperiodic Fibonacci sequence appears to fulfill the requirement for ensemble averaging for the systems studied here <ref:2609. p. 902645#pg9>
Data Availability and Acknowledgments
The original data sets used for the presented analysis are available at https://doi.org/10.15151/esrf-dc-2494118285 <ref:2609. p. 0 p. 002645#pg4> The ESRF is gratefully acknowledged for the provision of synchrotron beam time and financial resources <ref:2609.02645#pg4> ID02 beamline staff is thanked for technical support <ref:2609. p. 102645#pg4> R. Hino, T. Le Caer, M. Perez, S. Petitdemange and M. Sztucki are acknowledged for MAESTRIO device development and software integration <ref:2609. p. 102645#pg4> The software tools employed for the data processing can be found at https://gitlab.esrf.fr/id02/id02xpcs <ref:2609. p. 0 p. 002645#pg4> The authors state there is no conflict of interest to declare <ref:2609.02645#pg4> The authors contributed to the research as follows: WC, TG and TN designed the project; All authors participated in the research; WC, TN and YC carried out the experiments; WC programmed the correlator to compute g2(q, τ) in the bunch-mode acquisition and developed a model to fit the echoes; WC, TN and YC analyzed the data <ref:2609.02645#pg4> The paper includes references [1] through [42] <ref:2609. p. 002645#pg4>
Data Availability
The original data sets used for the presented analysis are available at https://doi.org/10.15151/esrf-dc-2494118285 <ref:2609.02645#pg4> The software tools employed for the data processing can be found at https://gitlab.esrf.fr/id02/id02xpcs <ref:2609.02645#pg4>
Author Contributions
WC, TG and TN designed the project; All authors participated in the research; WC, TN and YC carried out the experiments; WC programmed the correlator to compute g2(q, τ) in the bunch-mode acquisition and developed a model to fit the echoes; WC, TN and YC analyzed the data <ref:2609.02645#pg4>
Conflicts of Interest
There is no conflict of interest to declare <ref:2609.02645#pg4>
The results presented above demonstrate that XPCS-Echo measurements using a linear acquisition sequence enabled quantitative extraction of the dynamical parameters of a dense colloidal suspension subjected to an oscillatory deformation <ref:2609.02645#pg2> This approach becomes insufficient at lower frequencies and weaker deformations where very long measurements are required to cross the yield point <ref:2609. p. 502645#pg2> The bunch-mode acquisition is beneficial for covering a broad range of time scales with lower X-ray dose and data volume <ref:2609. p. 7 p. 702645#pg2> However, it suffers from the sparse sampling of TTCF which is an issue when investigating slowly relaxing nonergodic systems <ref:2609. p. 702645#pg9> The aperiodic Fibonacci sequence is a reasonable compromise to address the ensemble averaging issue for the systems studied here <ref:2609. p. 702645#pg9> The measured echoes in g2(q, τ) can be described quantitatively by an analytical expression <ref:2609. p. 9 p. 902645#pg2> This method will be useful for probing systems subjected to small amplitude and low frequency oscillatory shear or any other periodic motion <ref:2609. p. 9 p. 902645#pg2> The protocol of bunch-mode acquisition can be readily extended beyond XPCS to other dynamic scattering methods such as Differential Dynamic Microscopy (DDM) and multispeckle DLS <ref:2609. p. 9 p. 902645#pg2> The flexibility of bunch-mode acquisition may open up new possibilities for designing customized measurement schemes adapted to a broad range of dynamical processes <ref:2609. p. 9 p. 902645#pg2> The authors confirm the results presented above demonstrate that XPCS-Echo measurements using a linear acquisition sequence enabled quantitative extraction of the dynamical parameters of a dense colloidal suspension subjected to an oscillatory deformation <ref:2609. p. 502645#pg2> This approach becomes insufficient at lower frequencies and weaker deformations <ref:2609. p. 502645#pg2> The bunch-mode acquisition is beneficial for covering a broad range of time scales with lower X-ray dose and data volume <ref:2609.02645#pg2> However, it suffers from the sparse sampling of TTCF <ref:2609. p. 702645#pg9> The aperiodic Fibonacci sequence appears to fulfill this requirement for ensemble averaging for the systems studied here <ref:2609. p. 902645#pg9> The measured echoes in g2(q, τ) can be described quantitatively by an analytical expression <ref:2609.02645#pg2> This method will be useful for probing systems subjected to small amplitude and low frequency oscillatory shear or any other periodic motion <ref:2609.02645#pg2> The protocol of bunch-mode acquisition can be readily extended beyond XPCS to other dynamic scattering methods such as Differential Dynamic Microscopy (DDM) and multispeckle DLS <ref:2609.02645#pg2> The flexibility of bunch-mode acquisition may open up new possibilities for designing customized measurement schemes adapted to a broad range of dynamical processes <ref:2609.02645#pg2>
Figure 7
Figure 7 displays the normalized ultrasmall-angle X-ray scattering (USAXS) profiles from the stearyl silica suspension in the hard-sphere repulsive and short-range attractive gel states <ref:2609.02645#pg4> The inset depicts diffusive dynamics of the particles described by Eq. p. 6(5) with D ≃2.2 µm2s at 40 oC <ref:2609. p. 002645#pg4>
Figure 8
Figure 8 shows a comparison of g2(q, τ) functions from the stearyl silica suspension in the clustered state measured using the conventional linearly spaced frames (continuous lines) and by means of the bunch-mode (symbols) <ref:2609.02645#pg4> The X-ray dose for the latter was five times lower <ref:2609. p. 702645#pg4>
Figure 9
Figure 9 shows very slowly relaxing g2(q, τ) from the stearyl silica suspension in the deeply clustered state measured using the bunch-mode acquisition (symbols) <ref:2609.02645#pg4> The continuous lines are modeling in terms of the two-step relaxation in Eq. p. 6 p. 6(17) <ref:2609. p. 0 p. 002645#pg4> Notice the colossally large time range probed in a single acquisition <ref:2609. p. 9 p. 902645#pg4>
Figure 10
Figure 10 presents the q-dependence of the parameters ⟨τ1⟩, ⟨τ2⟩ and α from the analysis presented in Fig. 9 (with β1 ≃0. p. 6 p. 67 and β2 ≃0. p. 6 p. 63) <ref:2609. p. 0 p. 002645#pg4> Notice the scaling factors associated to ⟨τ1⟩ and ⟨τ2⟩, with the latter five −6 orders of magnitude larger <ref:2609. p. 7 p. 702645#pg4> The fast relaxation time constant scales as, ⟨τ1⟩ ∼ q−2 and the corresponding D ≃0. p. 7 p. 77 µm2s is much smaller than in the repulsive state <ref:2609. p. 7 p. 702645#pg4> The slow relaxation time constant varies as, ⟨τ2⟩ ∼ q−3 until the q range corresponding to the interparticle distance and below which it became nearly q independent <ref:2609. p. 7 p. 702645#pg4>
Figure 11
Figure 11 shows normalized USAXS profiles from the stearyl silica suspension in the hard-sphere repulsive and short-range attractive gel states <ref:2609.02645#pg4> The inset depicts the g2(q, τ) traces in the hard-sphere region indicating the diffusive dynamics with D ≃2. p. 62 µm2s <ref:2609. p. 002645#pg4>
Figure 13
Figure 13 shows very slowly relaxing g2(q, τ) from the stearyl silica suspension in the deeply clustered state measured using the bunch-mode acquisition (symbols) <ref:2609.02645#pg4> The continuous lines are modeling in terms of the two-step relaxation in Eq.(17) <ref:2609.02645#pg4> Notice the colossally large time range probed in a single acquisition <ref:2609.02645#pg4>
Figure 10 presents the q-dependence of the parameters ⟨τ1⟩, ⟨τ2⟩ and α from the analysis presented in Fig. 9 (with β1 ≃0.7 and β2 ≃0.3) <ref:2609.02645#pg4> Notice the scaling factors associated to ⟨τ1⟩ and ⟨τ2⟩, with the latter five −6 orders of magnitude larger <ref:2609.02645#pg4> The fast relaxation time constant scales as, ⟨τ1⟩ ∼ q−2 and the corresponding D ≃0.7 µm2s is much smaller than in the repulsive state <ref:2609.02645#pg4> The slow relaxation time constant varies as, ⟨τ2⟩ ∼ q−3 until the q range corresponding to the interparticle distance and below which it became nearly q independent <ref:2609.
Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.
Improvements for AI systems
-
Adaptive bunch acquisition systems can be implemented for systems exhibiting aging or non-stationary dynamics by triggering or spacing bunches based on real-time feedback from correlation statistics, pinning measurements where dynamic changes are most significant.
-
Phase-tracking acquisition can be used to study cyclic but anharmonic or multi-frequency driven systems where the driving force is not perfectly periodic, allowing a modified echo scheme to lock onto dynamically evolving phases to reconstruct complex time-dependent structural memory.
-
The resulting improved AI system can quantitatively extract the dynamical parameters of a dense colloidal suspension subjected to oscillatory deformation of relatively high frequency using XPCS-Echo measurements.
Sources
Related papers
- Coarse-graining dense, deformable active particles
- Three-body corrections to the Brownian viscosity of hard spheres without hydrodynamic interactions
- Thin active nematohydrodynamic layers: asymptotic theories and instabilities
- Origins of suppressed self-diffusion of nanoscale constituents of a complex liquid
- Soft material mechanical property degradation at high strain rates
- Avalanche criticality emerges by thermal fluctuation in a quiescent glass