A solid-solution approach for room-temperature bulk plasticity in KTa1-xNbxO3

arXiv:2608.26678 · cond-mat.mtrl-sci · Submitted 2026-08-27 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.

Kai: I'm Kai.

Mira: And I'm Mira, here with Lev.

Kai: We're looking at the paper: "A solid-solution approach for room-temperature bulk plasticity in KTa1-xNbxO3".

Mira: Here's the gist of the paper. Dislocations are being engineered into perovskite oxides to harvest versatile functional properties <ref:2608.26678#pg2> One major bottleneck, however, persists: perovskite oxides that can be engineered with dislocations, particularly via mechanical deformation at room temperature in bulk scale, have so far been limited to only three materials: SrTiO3 (2001, Brunner et al.), KNbO3 (2016, Mark et al.), and KTaO3 (2024, Fang & Zhang et al.) <ref:2608.26678#pg2>.

Kai: Here, we propose a simple and effective approach by using solid solution to significantly extend the range of materials <ref:2608.26678#pg2>.

Mira: Material Scope and Hypothesis The study focuses on KTa1-xNbxO3 (0<x<1) perovskite oxides for their bulk plasticity at room temperature <ref:2608.26678#pg2>.

Kai: The system involves substituting the B-site in the center of the perovskite unit cell with either Ta5+ or Nb5+ in a statistical distribution, which does not influence the species and concentration of charges in KTN <ref:2608.26678#pg2>.

Paper summary: Kai: So, wrapping up this paper, "A solid-solution approach for room-temperature bulk plasticity in KTa1-xNbxO3," the authors show that potassium tantalate niobate with an niobium fraction from zero to zero point five can exhibit bulk plasticity at room temperature.

Mira: They are using a solid solution method to find these materials, and they've shown it extends the range of materials we can study for this type of engineering.

Lev: The implication is that we have a new strategy for finding candidate oxides that could be used to engineer dislocations in devices, moving beyond the initial set of three examples.

Kai: This paves the road toward dislocation-engineered functional ceramics, which was previously limited by only those three perovskites.

Mira: It suggests that we can use controlled solid solution mixing to actively discover new oxides with desirable bulk plasticity characteristics for room temperature deformation.

Conclusion: Kai: So we're wrapping up this look at "A solid-solution approach for room-temperature bulk plasticity in KTa1 minus x Niobium Oxide." Basically, they’re showing how you can make these materials move in bulk at room temperature by just changing the recipe with solid solution.

Mira: That’s right. The authors are looking at potassium tantalate niobate with an atomic niobium fraction up to one point five, and they found that this mixing works for plastic deformation.

Lev: From my side, it means they’ve managed to find a way to make these materials actually move under load without needing extreme temperatures or pressures. That’s a huge hurdle for us when we think about building real devices.

Kai: It opens up a whole new set of candidates for what we can engineer at the dislocation level in future ceramics, moving past those few materials they mentioned before like strontium titanate and niobium oxide.

Mira: Exactly. The focus here isn't just on getting the plastic deformation, it’s on how that solid solution affects the room temperature stable phases, which changes based on how much niobium you put in there.

Lev: But we have to keep an eye on those structural defects they mentioned during growth because that’s what they think is actually blocking the dislocation motion and giving them that higher yield stress of around three hundred megapascals.

Kai: So, it’s not just about the mix; it seems like the way these materials are grown might be just as important as the substitution itself for getting those functional properties we want.

Mira: Right. It shows that using solid solution to tune these perovskites is a viable path for discovering new materials with bulk plasticity characteristics at room temperature.

Lev: What this means for me is that if we can predict which niobium concentration will create the best structure, we could narrow down the search space significantly before we even start growing crystals.

Institute for Applied Materials, Karlsruhe Institute of Technology · Department of Mechanical and Energy Engineering, Southern University of Science and Technology Department of Surface and Plasma Science, Faculty of Mathematics and Physics, Charles University Department 4 Advanced Materials Institute Qilu University of Technology Shandong Academy of Sciences

cond-mat.mtrl-sci

Submitted: 2026-08-27

Updated: 2026-08-27

Comments: 10 pages, 4 figures

Journal ref: Journal of the American Ceramic Society, 2026

DOI: 10.1111/jace.71417

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 77/100

The gist: Dislocations are being engineered into perovskite oxides to harvest versatile functional properties <ref:2608.26678#pg2> One major bottleneck, however, persists…

Key concepts

Dislocations
Dislocations are line defects within a crystal structure that allow materials to deform plastically without fracturing. Engineering these defects in perovskite oxides is the goal of this research, as it can be used to create materials with desired functional properties.
Solid Solution
This technique involves replacing some of the B-site atoms (Ta5+ or Nb5+) in a perovskite structure with another element. The study uses this substitution in KTa1-xNbxO3 to systematically explore how changing the composition affects the material's physical properties, specifically its ability to deform.
Yield Stress
Yield stress is the minimum stress required to cause permanent, plastic deformation in a material. The study measured this value for different KTa1-xNbxO3 compositions and found that KTN0.3 has a significantly higher yield stress (~300 MPa) than pure materials, indicating enhanced bulk plasticity.
Bulk Plasticity
Bulk plasticity refers to the material's ability to undergo permanent deformation when subjected to mechanical stress across its entire volume, rather than just surface effects. The study validated this by performing uniaxial compression tests and observing slip traces under indentation.

Terminology

Summary

Dislocations are being engineered into perovskite oxides to harvest versatile functional properties <ref:2608. p. 0

Where the paper says it

1 A solid-solution approach for room-temperature bulk plasticity in KTa1-xNbxO3 Alexander Frisch1 , Jiawen Zhang2 , Martin Setvin3 , Xuping Wang4 , Wenjun Lu2* , Xufei Fang1* 1 Institute for Applied Materials, Karlsruhe Institute of Technology, 76131 Karlsruhe, Germany 2Department of Mechanical and Energy Engineering, Southern University of Science and Technology, 518055 Shenzhen, China 3Department of Surface and Plasma Science, Faculty of Mathematics and Physics, Charles University, 18000 Prague, Czech Republic 4Advanced Materials Institute, Qilu University of Technology (Shandong Academy of Sciences), 250014 Jinan, China “The Tao produced One; One produced Two; Two produced Three; Three produced Infinity. ” Tao Te Ching, by Lao-tsu Abstract: Dislocations are being engineered into perovskite oxides to harvest versatile functional properties.

26678#pg2> One major bottleneck, however, persists: perovskite oxides that can be engineered with dislocations, particularly via mechanical deformation at room temperature in bulk scale, have so far been limited to only three materials: SrTiO3 (2001, Brunner et al. p. 0
Where the paper says it

” Tao Te Ching, by Lao-tsu Abstract: Dislocations are being engineered into perovskite oxides to harvest versatile functional properties. One major bottleneck, however, persists: perovskite oxides that can be engineered with dislocations, particularly via mechanical deformation at room temperature in bulk scale, have so far been limited to only three materials: SrTiO3 (2001, Brunner et al.

), KNbO3 (2016, Mark et al. p. 0
Where the paper says it

One major bottleneck, however, persists: perovskite oxides that can be engineered with dislocations, particularly via mechanical deformation at room temperature in bulk scale, have so far been limited to only three materials: SrTiO3 (2001, Brunner et al. ), KNbO3 (2016, Mark et al.

), and KTaO3 (2024, Fang & Zhang et al. p. 0
Where the paper says it

), KNbO3 (2016, Mark et al. ), and KTaO3 (2024, Fang & Zhang et al.

) <ref:2608.26678#pg2>. Here, we propose a simple and effective approach by using solid solution to significantly extend the range of materials <ref:2608. p. 0
Where the paper says it

), and KTaO3 (2024, Fang & Zhang et al. Here, we propose a simple and effective approach by using solid solution to significantly extend the range of materials.

26678#pg2>.

Material Scope and Hypothesis

The study focuses on KTa1-xNbxO3 (0<x<1) perovskite oxides for their bulk plasticity at room temperature <ref:2608.26678#pg2>. The system involves substituting the B-site in the center of the perovskite unit cell with either Ta5+ or Nb5+ in a statistical distribution, which does not influence the species and concentration of charges in KTN <ref:2608. p. 1

Where the paper says it

The resulting material system is potassium tantalate niobate (KTa1- xNbxO3, KTN; 0<x<1) [19-22], in which the B-site in the center of the perovskite unit cell is occupied by either Ta5+ or Nb5+ in a statistical distribution, as depicted in Figure 1A. As both ions carry the same charge state, substituting them for each other does not influence the species and concentration of charges in KTN.

26678#pg2>. Changes in the room-temperature stable phases are expected based on Nb concentration <ref:2608. p. 1
Where the paper says it

As both ions carry the same charge state, substituting them for each other does not influence the species and concentration of charges in KTN. Nevertheless, changes in the room-temperature stable phases are to be expected [23].

26678#pg2>. For instance, pure KTO is cubic at room temperature while pure KNO is orthorhombic <ref:2608. p. 1
Where the paper says it

Nevertheless, changes in the room-temperature stable phases are to be expected [23]. At room temperature, pure KTO is cubic while pure KNO is orthorhombic.

26678#pg2>.

Experimental Workflow Validation

A closed-loop validation workflow was constructed to test the hypothesis of bulk plasticity in KTa1-xNbxO3 <ref:2608.26678#pg2>. This workflow includes crystal growth, Brinell indentation, bulk compression, and transmission electron microscopy characterization <ref:2608. p. 0

Where the paper says it

Here, we propose a simple and effective approach by using solid solution to significantly extend the range of materials. We showcase KTa1-xNbxO3 (0<x<1) perovskite oxides for their bulk plasticity at room temperature by constructing a closedloop validation workflow that includes crystal growth, Brinell indentation, bulk compression, and transmission electron microscopy characterization.

26678#pg2>. The initial tests involve meso-scale Brinell indentation and scratching to indicate bulk plasticity <ref:2608. p. 1
Where the paper says it

It is expected that the yield stress of the KTN system shall be located within the two ends, if no solid solution hardening is present (Figure 1B, dashed line). In this rapid communication, we test our working hypothesis on KTN crystals with different Nb concentration by beginning with the meso-scale Brinell indentation [25] and scratching [13] tests, which have been proved as an effective method to indicate bulk plasticity.

26678#pg2>. To complete the testing loop, uniaxial bulk compression tests are performed to obtain the yield stress and macroscale plastic strain <ref:2608. p. 1
Where the paper says it

In this rapid communication, we test our working hypothesis on KTN crystals with different Nb concentration by beginning with the meso-scale Brinell indentation [25] and scratching [13] tests, which have been proved as an effective method to indicate bulk plasticity. Then, to complete the testing loop, uniaxial bulk compression tests are performed on available KTN crystals to obtain

26678#pg2>.

Plastic Deformation Analysis

Indentation imprints captured by laser confocal microscopy reveal crystallographic cross-hatched patterns which are slip traces due to plastic deformation <ref:2608.26678#pg2>. These slip traces are arranged vertically and horizontally on the (001) surfaces, corresponding to the activated 110 slip systems at room temperature for KTO [18] and KNO [17] <ref:2608. p. 3

Where the paper says it

The resulting crystallographic cross-hatched patterns in Figure 2B-D are the slip traces due to plastic deformation. The slip traces are arranged vertically and horizontally on the (001) surfaces, corresponding to the activated {110}<110> slip systems at room temperature, same for KTO [18] and KNO [17].

26678#pg2>. For KTN0.5, which is tetragonal, a typical ferroelectric domain pattern is observed around the indentation imprint <ref:2608. p. 3
Where the paper says it

5 is of the tetragonal phase and shows a typical ferroelectric domain pattern (strips indicated by the white arrows in Figure 2D). Around the indentation imprint (white dashed circle), domain fragmentation around the slip traces (vertical and horizontal lines as in the case of KTN0.

26678#pg2>.

Yield Stress Implications

The yield stress of ~300 MPa for KTN0.3 exceeds both the yield stress of ~270 MPa for pure KTO and ~60 MPa for pure KNO <ref:2608.26678#pg2>. This higher value is not necessarily attributed to solid solution hardening because the ionic radii of Ta5+ and Nb5+ do not differ significantly <ref:2608. p. 4

Where the paper says it

Normally a large difference between the ionic radii would cause lattice distortion to hinder the motion of dislocations, therefore increasing the yield stress [32]. As the ionic radii for Ta5+ and Nb5+ do not differ, negligible lattice distortion is expected to contribute to solid solution hardening.

26678#pg2>. Instead, the presence of structural defects induced during crystal growth is suggested as a factor that can effectively block dislocation motion to increase the yield stress <ref:2608. p. 4
Where the paper says it

It is unclear at this stage what these strips are, but given the fact that these strips persist during the following-up deformation process, they are immobile and not ferroelectric domains, but most likely some structural defects induced during the crystal growth, which remains a common challenge in growing KTNO crystals [33]. These structural defects can effectively block dislocation motion to increase the yield stress.

26678#pg2>.

Conclusion

The work demonstrates that solid-solution perovskite oxides, potassium tantalate niobate, with an Nb fraction (atomic) up to 0.5 can be plastically deformed in bulk at room temperature <ref:2608. p. 1

Where the paper says it

For perovskite oxides, which are of particular interest here, there have been so far only three materials reported to exhibit bulk plasticity mediated by dislocations at room temperature, namely, strontium titanate (SrTiO3, STO) in 2001 [16], potassium niobate in 2016 (KNbO3, KNO) [17], and potassium tantalate in 2024 (KTaO3, KTO) [18]. The question remains open: are there more perovskite oxides that can be plastically deformed in bulk at room temperature?

26678#pg2>. These findings open the path for active discovery of more plastically deformable oxides via the solid-solution approach <ref:2608. p. 6
Where the paper says it

The results suggest an infinite possibility of the composition KTa1-xNbxO3 (0<x<1) shall possess roomtemperature bulk plasticity, provided that the crystals can be synthesized, as no classic solid solution hardening was observed. These findings open the path for active discovery of more plastically deformable oxides via the solid-solution approach, and pave the road towards dislocation-engineered functional ceramics besides the previously reported but limited number of perovskite oxides (SrTiO3, KNbO3, and KTaO3).

26678#pg2>. The results pave the road towards dislocation-engineered functional ceramics besides the previously reported but limited number of perovskite oxides (SrTiO3, KNbO3, and KTaO3) <ref:2608. p. 6
Where the paper says it

The results suggest an infinite possibility of the composition KTa1-xNbxO3 (0<x<1) shall possess roomtemperature bulk plasticity, provided that the crystals can be synthesized, as no classic solid solution hardening was observed. These findings open the path for active discovery of more plastically deformable oxides via the solid-solution approach, and pave the road towards dislocation-engineered functional ceramics besides the previously reported but limited number of perovskite oxides (SrTiO3, KNbO3, and KTaO3).

26678#pg2>.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved AI can perform predictive modeling of room-temperature bulk plasticity across solid solution series KTa1-xNbxO3 (0<x<1) by integrating crystal growth data with mechanical testing results from Brinell indentation and bulk compression.

  2. The improved system can evaluate the feasibility of dislocation-tuned functionality for perovskite oxides beyond the three previously reported materials by systematically assessing material compositions based on the observed yield stress range.

  3. The AI can establish a closedloop validation workflow combining crystal growth, Brinell indentation, bulk compression, and transmission electron microscopy characterization to reliably confirm bulk plasticity in solid solution systems.

Abstract

Dislocations are being engineered into perovskite oxides to harvest versatile functional properties. One major bottleneck, however, persists: perovskite oxides that can be engineered with dislocations, particularly via mechanical deformation at room temperature in bulk scale, have so far been limited to only three materials: SrTiO3 (2001, Brunner et al.), KNbO3 (2016, Mark et al.), and KTaO3 (2024, Fang & Zhang et al.). Here, we propose a simple and effective approach by using solid solution to significantly extend the range of materials. We showcase KTa1-xNbxO3 (0<x<1) perovskite oxides for their bulk plasticity at room temperature by constructing a closed-loop validation workflow that includes crystal growth, Brinell indentation, bulk compression, and transmission electron microscopy characterization. Our findings are expected to unlock the materials toolbox for dislocation-tuned functionality of perovskite oxides.

Related papers