Electrostatic control of Li+ density and transport rate in double-gated van der Waals devices

arXiv:2608.23227 · cond-mat.mes-hall, physics.chem-ph · Submitted 2026-08-24 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Quantum Radio. Generated commentary on the latest quantum physics and condensed matter papers.

Kai: I'm Kai.

Mira: And I'm Mira, here with Lev.

Kai: We're looking at the paper: "Electrostatic control of Li+ density and transport rate in double-gated van der Waals devices".

Mira: Here's the gist of the paper. Ion transport in crystalline hosts is controlled by an applied potential that simultaneously sets ionic distribution and transport rate, restricting operation to a one-dimensional control space <ref:2608.23227#pg2> Here we show that the transport rate of Li+ ions in double-gated van der Waals devices can be modulated while the system occupies fixed ionic-density states <ref:2608.23227#pg2>.

Kai: The devices sustain over 1,000 switching cycles and function as hybrid ionic–electronic transistors capable of logic operations and memory retention, with ON/OFF ratios exceeding two orders of magnitude <ref:2608.23227#pg2>.

Mira: This work demonstrates a two-dimensional control space for ions intercalated in layered materials <ref:2608.23227#pg2>.

Kai: Device Architecture and Control Mechanism The research utilizes mechanically exfoliated few-layer graphene (FLG) or MoS2 stacked on a <50 nm thick hexagonal boron nitride (hBN) flake with a circular hole, forming a radially symmetric channel connecting two electrolyte reservoirs <ref:2608.23227#pg2>.

Paper summary: Kai: So we're wrapping up this look at "Electrostatic control of Li+ density and transport rate in double-gated van der Waals devices." The paper shows that by using two gate voltages, Vb and Vt, we can set the charge density and the electrochemical potential drop separately across a channel <ref:2608.23227#pg1>.

Mira: It really boils down to how applying a potential lets you dial in both where the lithium ions sit and how fast they move through these layered materials <ref:2608.23227#pg1>.

Kai: They showed these devices can switch over a thousand times without breaking down, and they operate as hybrid ionic–electronic transistors with huge ON/OFF ratios >

Lev: That's good because for real hardware, we need stability and high fidelity in those switching cycles <ref:2608.23227#pg1>.

Mira: The main point here is that you can modulate the transport rate while keeping the system at fixed ionic density states, which is a key finding for understanding how these materials work <ref:2608.23227#pg1>.

Lev: That’s useful because it points toward charge storage architectures that exploit this new way of accelerating ion movement <ref:2608.23227#pg1>.

Mira: And the paper gives us an estimate for the effective mobility, which seems to match what we see in other two-dimensional devices <ref:2608.23227#pg1>.

Lev: And they showed how differential gate tilts actually induce net ion flow, which is a specific mechanism we need to model when we try to build this on real hardware <ref:2608.23227#pg1>.

Mira: So the authors are demonstrating that this control over transport and density is achievable in these van der Waals systems >

Kai: And it opens up a whole new avenue for designing information-processing elements using ions, not just simple memory <ref:2608.23227#pg1>.

Lev: The challenge now is figuring out how to implement this level of control reliably on physical devices, considering the thermal activation energy involved <ref:2608.23227#pg1>.

Conclusion: Kai: So we're wrapping up this look at "Electrostatic control of Li+ density and transport rate in double-gated van der Waals devices."

Mira: It really boils down to how applying a potential lets you dial in both where the lithium ions are located and how fast they move through these layered materials.

Kai: The authors are showing us that by using two gate voltages, Vb and Vt, we can set the charge density and the electrochemical potential drop separately across a channel.

Lev: That means we're talking about a two-dimensional control space for ions intercalated in layered materials. It’s not just one setting anymore.

Mira: Exactly, so this isn't just a simple on or off switch; you have more degrees of freedom to tune the system, like the sigma V and delta V variables <ref:2608.23227#pg1>.

Kai: They showed these devices can switch over a thousand times without breaking down, and they operate as hybrid ionic–electronic transistors with huge ON/OFF ratios > one hundred.

Lev: That's good because for real hardware, we need stability and high fidelity in those switching cycles. We have to worry about the error correction overhead when you get that many cycles done <ref:2608.23227#pg1>.

Mira: The main point here is that you can modulate the transport rate while keeping the system at fixed ionic density states, which is a key finding for understanding how these materials work <ref:2608.23227#pg1>.

Kai: It suggests a new way to accelerate ionic transport that doesn't just rely on a single applied potential setting.

Lev: That’s useful because it points toward charge storage architectures that exploit this new way of accelerating ion movement <ref:2608.23227#pg1>.

Mira: And the paper gives us an order-of-magnitude estimate for the effective mobility, which seems to align with what we’ve seen in other two-dimensional devices <ref:2608.23227#pg1>.

Kai: So the big picture here is that double gating gives us a more versatile tool for manipulating these ion systems.

Lev: And they showed how differential gate tilts actually induce net ion flow, which is a specific mechanism we need to model when we try to build this on real hardware <ref:2608.23227#pg1>.

Mira: So the authors are demonstrating that this control over transport and density is achievable in these van der Waals systems.

Kai: And it opens up a whole new avenue for designing information-processing elements using ions, not just simple memory <ref:2608.23227#pg1>.

Lev: The challenge now is figuring out how to implement this level of control reliably on physical devices, considering the thermal activation energy involved <ref:2608.23227#pg1>.

Mira: So we're looking at a paper that shows how you can use electrostatic control to set the density and speed of lithium ion flow in layered materials <ref:2608.23227#pg1>.

E. Hoenig, X. Zhang, C. Li, J. Tong, G. Chen, L. Chen, D. Domaretskiy

Department of Physics and Astronomy, University of Manchester · National Graphene Institute, University of Manchester, UK

cond-mat.mes-hall, physics.chem-ph

Submitted: 2026-08-24

Updated: 2026-08-27

Journal ref: Nano Letters (2026)

DOI: 10.1021/acs.nanolett.6c02610

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 90/100

The gist: Ion transport in crystalline hosts is controlled by an applied potential that simultaneously sets ionic distribution and transport rate…

Key concepts

Double Gating Control Space
This refers to using two independent gate voltages (Vt and Vb) to control a 2D space. The sum ($\Sigma$V) controls the charge density across the channel, while the difference ($\Delta$V) controls the electrochemical potential drop. This allows for precise, simultaneous tuning of ion distribution and movement.
Ionic Current Hysteresis
The ionic current shows a 'hysteresis' effect where its value depends on its past history. Plateaus in this current correspond to specific, stable ionic-density states that are balanced by the electronic charge. This behavior is crucial for reliable switching and memory operations.
Electronic-Ionic Coupling
The electronic signal at the interface has two parts: smooth electrostatic doping and discrete charge changes during ion intercalation/deintercalation. Analyzing this balance helps determine the ionic density, revealing specific Li+ concentrations (e.g., nLi $\approx$ 6x10$^{13}$ cm$^{-2}$) corresponding to different current plateaus.

Terminology

Summary

Ion transport in crystalline hosts is controlled by an applied potential that simultaneously sets ionic distribution and transport rate, restricting operation to a one-dimensional control space <ref:2608. p. 0

Where the paper says it

Lozada-Hidalgo1,2 1Department of Physics and Astronomy, University of Manchester, Manchester, UK 2National Graphene Institute, University of Manchester, Manchester, UK 3Departamento de Física, Universidade Federal do Ceará, Fortaleza, Brazil 4School of Physics and Optoelectronic Engineering, Nanjing University of Information Science and Technology, Nanjing 210044, China. 5Departement Fysica, Universiteit Antwerpen, Antwerp, Belgium Abstract Ion transport in crystalline hosts is controlled by an applied potential that simultaneously sets ionic distribution and transport rate, restricting operation to a one-dimensional control space.

23227#pg2> Here we show that the transport rate of Li+ ions in double-gated van der Waals devices can be modulated while the system occupies fixed ionic-density states <ref:2608. p. 0
Where the paper says it

5Departement Fysica, Universiteit Antwerpen, Antwerp, Belgium Abstract Ion transport in crystalline hosts is controlled by an applied potential that simultaneously sets ionic distribution and transport rate, restricting operation to a one-dimensional control space. Here we show that the transport rate of Li⁺ ions in double-gated van der Waals devices can be modulated while the system occupies fixed ionic-density states.

23227#pg2>. The devices sustain over 1,000 switching cycles and function as hybrid ionic–electronic transistors capable of logic operations and memory retention, with ON/OFF ratios exceeding two orders of magnitude <ref:2608. p. 0
Where the paper says it

The ionic current exhibits pronounced hysteresis, with plateaus marking discrete ionic-density states balanced by electronic charge, while an independently tuneable electrochemical-potential drop controls the ionic transport rate. The devices sustain over 1,000 switching cycles and function as hybrid ionic– electronic transistors capable of logic operations and memory retention, with ON/OFF ratios exceeding two orders of magnitude.

23227#pg2>. This work demonstrates a two-dimensional control space for ions intercalated in layered materials <ref:2608. p. 0
Where the paper says it

The devices sustain over 1,000 switching cycles and function as hybrid ionic– electronic transistors capable of logic operations and memory retention, with ON/OFF ratios exceeding two orders of magnitude. This work demonstrates a two-dimensional control space for ions intercalated in layered materials.

23227#pg2>.

Device Architecture and Control Mechanism

The research utilizes mechanically exfoliated few-layer graphene (FLG) or MoS2 stacked on a <50 nm thick hexagonal boron nitride (hBN) flake with a circular hole, forming a radially symmetric channel connecting two electrolyte reservoirs <ref:2608.23227#pg2>. Two independent gate voltages, Vt and Vb, are applied to the devices to achieve independent control of the potential on each device-electrolyte interface <ref:2608. p. 1

Where the paper says it

Two gate voltages, Vt and Vb (top and bottom, respectively), were applied to the devices. This enabled independent control of the potential on each device-electrolyte interface, which was monitored with a Pt wire pseudoreference electrode (Fig.

23227#pg2>. The control variables are defined as the sum and difference of the gate voltages, ΣV = Vb + Vt and ΔV = Vb – Vt, which control charge density and electrochemical potential drop along the channel, respectively <ref:2608. p. 1
Where the paper says it

We set the control variables as the sum and difference of the gate voltages, ΣV = Vb + Vt and ΔV = Vb – Vt, following the standard protocol for double-gated devices33 . We adopt this convention and later show that these two variables control the charge density in the device and the electrochemical potential drop of Li+ ions along the channel, respectively.

23227#pg2>.

Ionic Transport Dynamics

The ionic current exhibits pronounced hysteresis with plateaus marking discrete ionic-density states balanced by electronic charge <ref:2608.23227#pg2>. The magnitude and qualitative form of the ionic-current response were preserved across multiple cycles and across 14 different devices, sustaining >1,000 ON/OFF cycles without degradation <ref:2608. p. 1

Where the paper says it

These features were reproducible across multiple cycles of a device and across 14 different devices (Fig. The magnitude and qualitative form of the ionic-current response were also preserved when scanning rate was varied by more than an order of magnitude (Fig.

23227#pg2>. The transport occurs along the 2D interface, confirmed by measurements on reference devices with channel edges blocked by SU-8 seal <ref:2608. p. 1
Where the paper says it

Overall, the ionic response displayed a hysteresis loop with an ON-OFF ratio of ≈10², and devices could sustain >1,000 of such ON-OFF cycles without degradation (Fig. To confirm that the transport occurs along the 2D interface, we measured reference devices with channel edges blocked by the SU-8

23227#pg2>. Furthermore, the plateau currents scale linearly with ΔV for a fixed density stage, confirming that ΔV linearly sets the transport rate at each fixed density stage <ref:2608. p. 0
Where the paper says it

5Departement Fysica, Universiteit Antwerpen, Antwerp, Belgium Abstract Ion transport in crystalline hosts is controlled by an applied potential that simultaneously sets ionic distribution and transport rate, restricting operation to a one-dimensional control space. Here we show that the transport rate of Li⁺ ions in double-gated van der Waals devices can be modulated while the system occupies fixed ionic-density states.

23227#pg2>.

Electronic-Ionic Coupling Analysis

The electronic charge density at the FLG/hBN interface has two contributions: smooth electrostatic doping and charge introduced in stepwise intercalation events <ref:2608.23227#pg2>. The electronic signal exhibits balanced charge–discharge events during the intercalation–deintercalation cycle that are independent of ΔV <ref:2608. p. 3

Where the paper says it

S8 and Section S4). These findings demonstrate that the electronic signal exhibits balanced charge– discharge events during the intercalation–deintercalation cycle controlled by ΣV that are independent of ΔV.

23227#pg2>. This balance allows for an estimate of the ionic density from the electronic charge-discharge analysis, revealing nLi ≈ 6x1013 cm−2 at the highest plateau <ref:2608. p. 3
Where the paper says it

This balance allows for an estimate of the ionic density from the electronic charge-discharge analysis in Fig. This reveals nLi ≈ 6x1013 cm-2 at the highest plateau, decreasing in steps of ΔnLi ≈ 2x1013 cm-2 until the interface is discharged (Section S4).

23227#pg2>.

Performance Advantages and Applications

Double gating offers two key performance advantages over single-voltage controlled architectures: enhanced ON-OFF cyclability, sustaining >1,000 cycles without degradation <ref:2608.23227#pg2>, and control of transport by tuning the electrochemical potential drop rather than relying solely on a single applied potential <ref:2608. p. 5

Where the paper says it

S5), double-gated devices can sustain >1,000 cycles without degradation. Second, double gating enables control of transport by tuning the electrochemical potential drop along the channel, rather than relying solely on a single applied potential.

23227#pg2>. This approach could enable future charge storage architectures that exploit this new way of accelerating ionic transport <ref:2608. p. 5
Where the paper says it

In single-gate controlled devices, faster ion transport often requires higher operating potentials, which can induce parasitic side reactions or even device failure23 . Our findings suggest that double gating could enable future charge storage architectures that exploit this new way of accelerating ionic transport.

23227#pg2>. The devices are demonstrated as information-processing elements, functioning as ionic transistors and programmable memory devices <ref:2608. p. 5
Where the paper says it

To illustrate the robust control over intercalation enabled by our devices, we operate them as information-processing elements (Fig. In the first mode, they function as ionic transistors.

23227#pg2>.

Theoretical Modeling and Mobility Estimation

The geometric proportionality factor for the ionic current is given by A = 2π ln(r2/r1), leading to the compact form i = AenLiµΔV <ref:2608.23227#pg2>. The effective mobility µ incorporates a thermally activated factor, exp(-Ea/kBT), where Ea ≈ 0. p. 5

Where the paper says it

6 constant (Section S5) and µ the effective mobility of Li+ . The latter term incorporates a thermally activated factor, exp(-Ea/kT), where Ea = 0.

6 ± 0.2 eV for FLG and 0. p. 1
Where the paper says it

This enables direct mapping of Li⁺ transport as a function of ionic density and electrochemical potential drop along the channel and allows transport to be accelerated without necessarily increasing the potential of the ion-supplying reservoir. Results Our devices consist of mechanically exfoliated few-layer graphene (FLG) or MoS2, stacked on a <50 nm thick hexagonal boron nitride (hBN) flake with a circular hole 3–5 µm in diameter (Fig.

7 ± 0.1 eV for MoS2 devices <ref:2608. p. 0
Where the paper says it

Here we show that the transport rate of Li⁺ ions in double-gated van der Waals devices can be modulated while the system occupies fixed ionic-density states. We measure the ionic current along the van der Waals interfaces between hexagonal boron nitride and graphene or MoS2 while simultaneously monitoring the in-plane electronic response.

23227#pg2>. An order-of-magnitude estimate of the effective mobility is derived as µ ≈ (A e nLi)−1 ∂i/∂ΔV ≈ 1x10−4 cm2 V−1 s−1 <ref:2608. p. 5
Where the paper says it

2 eV, reflects the barrier for Li+ entry into the channel. An order-of-magnitude estimate of the effective mobility can thus be derived from the transport data as: µ = (A e nLi) -1 ∂i/∂ΔV ≈ 1x10-4 cm2 V -1 s -1 for all plateaus.

23227#pg2>. The estimated Li+ density and mobility are in reasonable agreement with previous reports for Li+ transport in 2D devices <ref:2608. p. 5
Where the paper says it

We find that the estimated Li+ density and mobility are in reasonable agreement with previous reports for Li+ transport in 2D devices15,28,32 (Section S5). Taken together, these observations demonstrate that double-gated devices enable transistor-like control of Li⁺ transport in van der Waals devices.

23227#pg2>.

Conclusion on Control Space

The consistent charge balance (Δn0 ≈ Δn1 + Δn2 + Δn3) and the independence of the total charge across the full ΔV range tested indicate that, within our resolution, the total Li+ occupancy set at each ΣV-defined stage is not measurably altered by ΔV <ref:2608.23227#pg2>. The resulting ionic current i is proportional to the difference in electrochemical potential defined by the two gates, Δµ̃ = e ΔV, allowing transport to be described phenomenologically using a drift–diffusion model along a 2D channel <ref:2608. p. 4

Where the paper says it

The resulting ionic current, i, on the other hand, is proportional to the difference in the electrochemical potential defined by the two gates, Δµ̃. This allows describing the transport phenomenologically using a drift–diffusion model along a 2D channel: i = A nLi µ Δµ̃, where A is a unitless device geometry 2 0 1 2 3 0 1 2 3Ionic Current (nA) SV (V) 3 2 0 1 2 3 0.

23227#pg2>. The work demonstrates that double-gated devices enable transistor-like control of Li+ transport in van der Waals devices <ref:2608. p. 5
Where the paper says it

We find that the estimated Li+ density and mobility are in reasonable agreement with previous reports for Li+ transport in 2D devices15,28,32 (Section S5). Taken together, these observations demonstrate that double-gated devices enable transistor-like control of Li⁺ transport in van der Waals devices.

23227#pg2>.

Supporting Information Details

Device fabrication involved defining apertures by photolithography and RIE, followed by transfer onto the hBN/SiNx substrate <ref:2608.23227#pg2>. Electrolyte characterization showed that the bulk electrolyte does not limit ion transport in our devices <ref:2608. p. 7

Where the paper says it

8 Supporting Information Methods (sections S1 to S7) including device fabrication, measurement protocols and theoretical description of Li+ transport. Figures S1 to S12, showing device schematics and images, additional device and electrolyte characterization, reproducibility and theoretical results (PDF).

23227#pg2>. The analysis of discrete intercalation states is based on four allowed Li+ densities, nLi = l × ΔnLi, with ΔnLi ≈ 2x1013 cm−2 and l = 0, 1, 2, 3 <ref:2608. p. 3
Where the paper says it

This balance allows for an estimate of the ionic density from the electronic charge-discharge analysis in Fig. This reveals nLi ≈ 6x1013 cm-2 at the highest plateau, decreasing in steps of ΔnLi ≈ 2x1013 cm-2 until the interface is discharged (Section S4).

23227#pg2>. The analysis of the Gibbs free energy shows that intercalation threshold corresponds to a line in the (ΣV, ΔV)–plane given by ΣV = 2Vb − ΔV <ref:2608. p. 1
Where the paper says it

1b shows the typical ionic current response, i, of FLG and MoS2 devices at fixed ΔV for ΣV > 0, such that the devices were electron doped. At low ΣV, the current remained within the background level (<10 pA), but beyond a threshold, which depended on the crystal (FLG or MoS2), it rose sharply, sometimes displaying closely spaced jumps, before reaching a plateau.

23227#pg2>. The ionic current is described by a drift-diffusion model for radial geometry: i = 2π ln(r2/r1)−1 enLi µLi ΔV exp(-Ea/kBT) <ref:2608. p. 4
Where the paper says it

The resulting ionic current, i, on the other hand, is proportional to the difference in the electrochemical potential defined by the two gates, Δµ̃. This allows describing the transport phenomenologically using a drift–diffusion model along a 2D channel: i = A nLi µ Δµ̃, where A is a unitless device geometry 2 0 1 2 3 0 1 2 3Ionic Current (nA) SV (V) 3 2 0 1 2 3 0.

23227#pg2>. The energy profile of Li+ in double-gated devices shows that the differential gate tilts the energy profile of the channel, inducing net ion flow <ref:2608. p. 1
Where the paper says it

We set the control variables as the sum and difference of the gate voltages, ΣV = Vb + Vt and ΔV = Vb – Vt, following the standard protocol for double-gated devices33 . We adopt this convention and later show that these two variables control the charge density in the device and the electrochemical potential drop of Li+ ions along the channel, respectively.

23227#pg2>. The system is ON (OFF) when a high (low) pulse is applied to ΣV, charging (discharging) Li+ ions <ref:2608. p. 6
Where the paper says it

ΣV and ΔV are set as the digital WRITE and analogue READ inputs, respectively. The schematic shows that the system is ON (OFF) when a high (low) pulse is applied to ΣV, charging (discharging) Li+ ions (shown as grey spheres) in the hBN/FLG interface (shown as planes).

23227#pg2>. The WRITE signal sets the device into an intermediate, history dependent state <ref:2608. p. 5
Where the paper says it

The associated electronic responses provide a secondary signal that tracks the intercalation–deintercalation events, superimposed with a volatile component that follows the WRITE voltage pulses. In MoS₂, this volatile response drives the device fully into an insulating state during the OFF pulse.

23227#pg2>.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Enhanced ionic transport modeling allows AI systems to predict Li+ density and transport rate simultaneously, enabling a two-dimensional control space for ions intercalated in layered materials. This capability permits designing charge storage architectures that exploit double gating for transistor-like control of Li+ transport.

  2. Development of hybrid ionic–electronic transistors enables logic operations and memory retention with ON/OFF ratios exceeding two orders of magnitude, allowing AI systems to function as programmable information-processing elements. These devices can be used as ionic transistors where ionic current is switched ON or OFF via the sum gate voltage while the difference gate voltage continuously tunes the current magnitude for analog readout.

  3. Integration of non-volatile ionic memory with volatile electronic responses allows AI systems to construct programmable memory devices for neuromorphic computing. This enables creating devices where the associated electronic responses provide a secondary signal that tracks the intercalation–deintercalation events, superimposed with a volatile component that follows the WRITE voltage pulses.

Abstract

Ion transport in crystalline hosts is controlled by an applied potential that simultaneously sets ionic distribution and transport rate, restricting operation to a one-dimensional control space. Here we show that the transport rate of Li+ ions in double-gated van der Waals devices can be modulated while the system occupies fixed ionic-density states. We measure the ionic current along the van der Waals interfaces between hexagonal boron nitride and graphene or MoS2 while simultaneously monitoring the in-plane electronic response. The ionic current exhibits pronounced hysteresis, with plateaus marking discrete ionic-density states balanced by electronic charge, while an independently tuneable electrochemical-potential drop controls the ionic transport rate. The devices sustain over 1,000 switching cycles and function as hybrid ionic-electronic transistors capable of logic operations and memory retention, with ON/OFF ratios exceeding two orders of magnitude. This work demonstrates a two-dimensional control space for ions intercalated in layered materials.

Related papers