Electrical Control over Volatile Mott Switching through Non-Volatile Memory Effects

arXiv:2607.28787 · cond-mat.mtrl-sci · Submitted 2026-07-30 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.

Kai: We're looking at the paper: "Electrical Control over Volatile Mott Switching through Non-Volatile Memory Effects".

Mira: Here's the gist of the paper. Electrical Control over Volatile Mott Switching through Non-Volatile Memory Effects shows that volatile switching in vanadium oxides can be strongly affected by non-volatile processes associated with the creation and annihilation of the conducting filament, giving rise to pronounced memory effects where initial switching voltage substantially exceeds that of subsequent cycles <ref:2607.28787#pg2> The authors identify two distinct mechanisms underlying this behavior in different thermal regimes <ref:2607.28787#pg4> Material Properties and Switching Dynamics Vanadium Dioxide (VO2) and Vanadium Sesquioxide (V2O3) are Mott insulators that undergo an Insulator-to-Metal Transition (IMT) at approximately 340K and approximately 160K, respectively, which manifests as an orders-of-magnitude reduction in their electrical resistance <ref:2607.28787#pg3> These transitions provide the physical basis for their Volatile Resistive Switching (VRS) behavior, making them promising candidates for threshold-switching devices <ref:2607.28787#pg2> In V2O3 the transition involves a change in resistivity of up to 6 orders-of-magnitude, coupled with a structural and magnetic transformation <ref:2607.28787#pg2> Below the critical temperature (approximately 160 K), V2O3 is in an insulating antiferromagnetic monoclinic phase, while above this temperature it transforms into a metallic paramagnetic rhombohedral phase <ref:2607.28787#pg3> In VO2 the IMT is characterized by up to 4 orders of magnitude change in resistivity, coupled with a structural transition from a low-temperature insulating monoclinic phase to a high-temperature metallic rutile phase <ref:2607.28787#pg2> Mechanisms of Memory Effects The paper identifies two distinct types of memory effects observed in V2O3 and VO2 devices, which occur in different temperature regimes and originate from different physical mechanisms <ref:2607.28787#pg4> 1.

Kai: In the phase-coexistence regime, V2O3 exhibits a memory effect that is distinct from the conventional memory effect associated with the heating and cooling branches of the hysteresis loop <ref:2607.28787#pg5> This behavior suggests that the initial switching event redistributes metallic and insulating domains in a manner which is more conducive to filament formation than the initial domain configuration, and this effect is reversible and can be erased by thermal cycling <ref:2607.28787#pg6> 2.

Mira: At lower temperatures, in both materials, there is an intermediate regime where no clear memory effect is observed, but upon further cooling in the fully insulating state, both V2O3 and VO2 exhibit a similar memory effect where the initial switching voltage is higher than in subsequent switching events <ref:2607.28787#pg4> The authors attribute this low-temperature memory effect to mild electroforming, where defect formation and/or migration is induced by the combination of a high electric field and current surge due to the initial switching event <ref:2607.28787#pg4> Characterization of Switching Processes The study utilizes several experimental techniques, including Resistance vs.

Kai: Temperature (R(T)) Measurements and Current vs.

Paper summary: Mira: Thinking about the title, "Electrical Control over Volatile Mott Switching through Non-Volatile Memory Effects", it really emphasizes that we aren't just looking at the switching event itself, but how those non-volatile memory effects control it <ref:2607.28787#pg1>.

Kai: Exactly. They’ve shown that what happens non-volatily—the creation and annihilation of the conducting filament—has a huge influence on the volatile switching behavior <ref:2607.28787#pg1>.

Lev: So, when we look at the results, they've identified two distinct physical mechanisms causing this memory effect: one being spatial redistribution in V2O3 in its phase coexistence regime, and the other being a defect-mediated effect at lower temperatures <ref:2607.28787#pg6>.

Mira: These mechanisms operate under different thermal regimes, which is important because it dictates how you can control the switching voltage through post-fabrication tuning <ref:2607.28787#pg5>.

Kai: What this means simply for us is that we can use defect introduction to tune resistive switching electronics, and this isn't just confined to vanadium oxides; it suggests a pathway for tunable resistive-switching devices <ref:2607.28787#pg6>.

Conclusion: Kai: So, this paper is about controlling switching in these vanadium oxides using memory effects that aren't volatile at all <ref:2607.28787#pg1>.

Mira: Right, it focuses on how non-volatile processes, like the filament forming and breaking, actually dictate how the material switches electricity <ref:2607.28787#pg1>.

Lev: We’re seeing this happen in both vanadium dioxide and sesquioxide materials across different temperatures <ref:2607.28787#pg4>.

Kai: The authors found these memory effects are tied to two different physics, one happening in phase coexistence and another at lower temperatures <ref:2607.28787#pg4>.

Mira: That means the initial state of the material really matters for how it switches later, and that initial state is set by these non-volatile events <ref:2607.28787#pg5>.

Lev: If we can control those non-volatile processes, we can tune the switching voltage or power over a wider temperature range <ref:2607.28787#pg5>.

Kai: It suggests that defect introduction might be a way to achieve that tuning because the memory effect at low temperatures is linked to defects forming <ref:2607.28787#pg4>.

Mira: That’s what we need to keep in mind when thinking about building more reliable switching devices, because controlling those defects gives us a new handle on the electronics <ref:2607.28787#pg6>.

Lev: It opens up the idea that we can move away from just aggressive switching events toward a controlled sequence of gradual forming steps <ref:2607.28787#pg6>.

Kai: So, it’s about using memory effects to make the switching process predictable instead of random <ref:2607.28787#pg1>.

Mira: Exactly, moving from a purely stochastic event to one where we can introduce controlled modifications through those non-volatile states <ref:2607.28787#pg6>.

Lev: And the big thing is that this defect mechanism isn't just for vanadium oxides; it points toward other Mott insulators like niobium dioxide <ref:2607.28787#pg6>.

Amihai Kronman, Gil Levi, Yoav Kalcheim

Department of Materials Science and Engineering, Technion - Israel Institute of Technology

cond-mat.mtrl-sci

Submitted: 2026-07-30

Updated: 2026-11-04

Comments: 22 pages, 8 figures, 12 supplementary pages, 7 supplementary figures; Acknowledgements section updated

License: http://creativecommons.org/licenses/by-sa/4.0/

Importance score: 85/100

The gist: Electrical Control over Volatile Mott Switching through Non-Volatile Memory Effects shows that volatile switching in vanadium oxides can be strongly affected by non-volatile processes associated with…

Key concepts

Volatile Resistive Switching (VRS)
This is the process where a material changes its electrical resistance from insulating to metallic states based on temperature or electric field. In vanadium oxides, this transition involves a structural change that drastically alters conductivity, making them useful for memory devices.
Memory Effects
These are persistent changes in device behavior after an initial operation, such as switching. The paper identifies two types: one related to how the material's domains rearrange itself during the first switch, and another caused by creating defects that permanently alter the material's properties for future switches.
Insulator-to-Metal Transition (IMT)
This is a critical change in vanadium oxides where they switch from an insulating state to a metallic state. This transition occurs at specific temperatures (like 340K for VO2) and involves significant changes in electrical resistance, which is the basis for their switching behavior.

Terminology

Summary

Electrical Control over Volatile Mott Switching through Non-Volatile Memory Effects shows that volatile switching in vanadium oxides can be strongly affected by non-volatile processes associated with the creation and annihilation of the conducting filament, giving rise to pronounced memory effects where initial switching voltage substantially exceeds that of subsequent cycles <ref:2607. p. 0

Where the paper says it

Here, we show that the volatile switching in these materials can be strongly affected by non-volatile processes associated with the creation and annihilation of the conducting filament. These processes give rise to pronounced memory effects in which the initial switching voltage substantially exceeds that of subsequent cycles.

28787#pg2> The authors identify two distinct mechanisms underlying this behavior in different thermal regimes <ref:2607. p. 0
Where the paper says it

These processes give rise to pronounced memory effects in which the initial switching voltage substantially exceeds that of subsequent cycles. We identify two distinct mechanisms underlying this behavior in different thermal regimes.

28787#pg4>

Material Properties and Switching Dynamics

Vanadium Dioxide (VO2) and Vanadium Sesquioxide (V2O3) are Mott insulators that undergo an Insulator-to-Metal Transition (IMT) at approximately 340K and approximately 160K, respectively, which manifests as an orders-of-magnitude reduction in their electrical resistance <ref:2607.28787#pg3> These transitions provide the physical basis for their Volatile Resistive Switching (VRS) behavior, making them promising candidates for threshold-switching devices <ref:2607. p. 0

Where the paper says it

Electrical Control over Volatile Mott Switching through Non-Volatile Memory Effects Amihai Kronman†,1 , Gil Levi†,1 , and Yoav Kalcheim1 1Department of Materials Science and Engineering, Technion - Israel Institute of Technology, Haifa, Israel ABSTRACT Vanadium Dioxide (VO2) and Vanadium Sesquioxide (V2O3) are Mott insulators that undergo an Insulator-to-Metal Transition (IMT) at ∼340K and ∼160K, respectively, manifested as an orders-ofmagnitude reduction in their electrical resistance. These transitions provide the physical basis for their Volatile Resistive Switching (VRS) behavior, making them promising candidates for threshold-switching devices.

28787#pg2> In V2O3 the transition involves a change in resistivity of up to 6 orders-of-magnitude, coupled with a structural and magnetic transformation <ref:2607. p. 1
Where the paper says it

These vanadium oxides are prototypical correlated electron materials that exhibit an IMT accompanied by a several orders-of-magnitude changes in resistivity [24], making them ideal materials for IMT-based resistive switching devices. In V2O3 the transition involves a change in resistivity of up to 6 orders-of-magnitude, coupled with a structural and magnetic transformation [25].

28787#pg2> Below the critical temperature (approximately 160 K), V2O3 is in an insulating antiferromagnetic monoclinic phase, while above this temperature it transforms into a metallic paramagnetic rhombohedral phase <ref:2607. p. 1
Where the paper says it

In V2O3 the transition involves a change in resistivity of up to 6 orders-of-magnitude, coupled with a structural and magnetic transformation [25]. Below the critical temperature (∼160 K), V2O3 is in an insulating antiferromagnetic monoclinic phase, while above this temperature it transforms into a metallic paramagnetic rhombohedral phase [26, 27].

28787#pg3> In VO2 the IMT is characterized by up to 4 orders of magnitude change in resistivity, coupled with a structural transition from a low-temperature insulating monoclinic phase to a high-temperature metallic rutile phase <ref:2607. p. 1
Where the paper says it

Below the critical temperature (∼160 K), V2O3 is in an insulating antiferromagnetic monoclinic phase, while above this temperature it transforms into a metallic paramagnetic rhombohedral phase [26, 27]. In VO2 the IMT is characterized by up to 4 orders of magnitude change in resistivity, coupled with a structural transition from a low-temperature insulating monoclinic phase to a high-temperature metallic rutile phase [28–30].

28787#pg2>

Mechanisms of Memory Effects

The paper identifies two distinct types of memory effects observed in V2O3 and VO2 devices, which occur in different temperature regimes and originate from different physical mechanisms <ref:2607.28787#pg4> 1. In the phase-coexistence regime, V2O3 exhibits a memory effect that is distinct from the conventional memory effect associated with the heating and cooling branches of the hysteresis loop <ref:2607. p. 2

Where the paper says it

We identify two distinct types of memory effects, which occur in different temperature regimes and originate from different physical mechanisms. Within the phase-coexistence regime, V2O3 exhibits a memory effect that is distinct from the conventional memory effect associated with the heating and cooling branches of the hysteresis loop.

28787#pg5> This behavior suggests that the initial switching event redistributes metallic and insulating domains in a manner which is more conducive to filament formation than the initial domain configuration, and this effect is reversible and can be erased by thermal cycling <ref:2607. p. 2
Where the paper says it

This behavior suggests that the initial switching event redistributes the metallic and insulating domains in a manner which is more conducive to filament formation than the initial domain configuration. The effect is reversible and can be erased by thermal cycling (i.

28787#pg6> 2. At lower temperatures, in both materials, there is an intermediate regime where no clear memory effect is observed, but upon further cooling in the fully insulating state, both V2O3 and VO2 exhibit a similar memory effect where the initial switching voltage is higher than in subsequent switching events <ref:2607. p. 2
Where the paper says it

At lower temperatures, in both materials, we identify an intermediate regime in which the IV sweeps are highly repeatable, and no clear memory effect is observed. Upon further cooling in the fully insulating state, both V2O3 and VO2 exhibit a similar memory effect where the initial switching voltage is higher than in subsequent switching events.

28787#pg4> The authors attribute this low-temperature memory effect to mild electroforming, where defect formation and/or migration is induced by the combination of a high electric field and current surge due to the initial switching event <ref:2607. p. 2
Where the paper says it

However, unlike the phase-coexistence memory, this memory effect is not erased by thermal cycling. We attribute this low-temperature memory effect to mild electroforming, where defect formation and/or migration is induced by the combination of a high electric field and current surge due to the initial switching event.

28787#pg4>

Characterization of Switching Processes

The study utilizes several experimental techniques, including Resistance vs. Temperature (R(T)) Measurements and Current vs. p. 3

Where the paper says it

Electrical transport measurements Resistance vs. Temperature (R(T)) Measurements and Current vs.

Voltage (IV) measurements using an internal resistor to suppress current surges following the IMT <ref:2607. p. 2
Where the paper says it

Each device is composed of a small gap of ∼4µm between the electrodes, and two larger gaps in the middle of each electrode (Figure 1 inset). The larger gaps act as internal resistors that suppress current surges following the IMT, thereby protecting the device.

28787#pg5> The inclusion of an internal resistor can substantially reduce the surge-induced damage, as shown by estimating the equivalent heating in terms of temperature increase <ref:2607.28787#pg6> For a V2O3 device with an internal resistor, the estimated equivalent heating is approximately 1K <ref:2607. p. 3
Where the paper says it

When using an external resistor, the parasitic capacitance of the wiring between the resistor and the device is large enough to cause permanent damage to the device as well (See supplementary section S3). To circumvent this, we incorporated an internal series resistor into the device geometry (as indicated by the arrows in the inset of Figure 1) which consists of a significantly larger gap of the same oxide (V2O3 and VO2).

28787#pg6> This demonstrates that catastrophic device failure is avoided when using an internal resistor compared to the unprotected case <ref:2607. p. 3
Where the paper says it

When using an external resistor, the parasitic capacitance of the wiring between the resistor and the device is large enough to cause permanent damage to the device as well (See supplementary section S3). To circumvent this, we incorporated an internal series resistor into the device geometry (as indicated by the arrows in the inset of Figure 1) which consists of a significantly larger gap of the same oxide (V2O3 and VO2).

28787#pg6>

Control and Tuning of Switching Parameters

The defect-related memory effect at low temperatures can be harnessed for post-fabrication tuning, allowing for controlled modification of the switching voltage and power over a wide temperature range <ref:2607.28787#pg5> The proposed tuning procedure involves an initial IV sweep to determine parameters, followed by cooling to a lower temperature for a subsequent IV measurement at an operating temperature where no memory effect was observed <ref:2607. p. 9

Where the paper says it

The tuning procedure is as follows: an initial IV sweep is recorded at an operating temperature to determine the initial switching parameters, after which the device is cooled to a lower temperature for a subsequent IV measurement (the ’writing step’). The device is then returned to the operating temperature while remaining on the cooling curve, achieved by heating it into the fully metallic state and then re-cooling, before a second IV measurement is performed.

28787#pg6> Gradual writing protocols, such as those performed in 20K intervals from 300K to 220K, resulted in a reduction of the switching voltage by a factor of approximately 2. p. 4
Where the paper says it

Leveraging the protection provided by the internal resistor, multiple consecutive IV sweeps were performed at low temperatures. Despite the reduction of the power surge, it is not fully eliminated, and the IV curves revealed a significant decrease in the switching voltage between the initial IV sweep and subsequent measurements (Figure 2).

5 and the switching power by a factor of about 6 <ref:2607. p. 0
Where the paper says it

contributed equally to this work. arXiv:2607.

28787#pg6> This gradual approach avoids structural damage, unlike sudden writing steps which produce cracks oriented parallel to the electrodes <ref:2607.28787#pg6>

Conclusion on Memory Mechanisms

The research reveals two distinct memory mechanisms in vanadium oxide VRS devices: a spatial redistribution of metallic and insulating domains in V2O3 within the phase-coexistence regime, and a defect-mediated memory effect in both oxides at low temperatures within the fully insulating state <ref:2607.28787#pg6> The defect-related low-temperature memory effect is understood as part of a broader hierarchy of current surge-induced device modifications <ref:2607. p. 2

Where the paper says it

We attribute this low-temperature memory effect to mild electroforming, where defect formation and/or migration is induced by the combination of a high electric field and current surge due to the initial switching event. Finally, we show the practical importance of the low temperature memory effect for device operation.

28787#pg6> This interplay between volatile switching and non-volatile material modification transforms the electroforming from a single aggressive event into a controlled sequence of gradual forming steps <ref:2607. p. 2
Where the paper says it

By incorporating an internal resistor that limits the current surge, electroforming can be performed gradually at low temperatures, allowing defects to be introduced in a controlled manner rather than through an abrupt, aggressive forming event which damages the device. This approach enables tuning of the switching voltage over a wide temperature range, including the intermediate regime when no memory effect is observed, providing a pathway for enhanced all-electrical control of the VRS parameters, such as switching voltage and power.

28787#pg6> The defect-mediated memory effect provides a robust mechanism for post-fabrication device tuning, establishing controlled defect introduction as a promising pathway for tunable resistive-switching electronics <ref:2607. p. 9
Where the paper says it

Having established that the low-temperature and phase-coexistence memory effects arise from distinct mechanisms, the remainder of the main text focuses on the defect-related memory effect. This effect is particularly important because it enables controllable modification of the switching voltage and can therefore be exploited for post-fabrication tuning of device properties.

28787#pg6>

Supplementary Information on Stochasticity

In the phase-coexistence regime, switching can be triggered by the transformation of a single critical domain that completes a percolating metallic path across the device, leading to large variations in initial device resistance <ref:2607.28787#pg6> Repeated IV measurements separated by thermal-cycling steps showed that while individual sweeps exhibit stochasticity, the difference between the first IV sweep and subsequent sweeps remains robust <ref:2607. p. 2

Where the paper says it

Within the phase-coexistence regime, V2O3 exhibits a memory effect that is distinct from the conventional memory effect associated with the heating and cooling branches of the hysteresis loop. Even when the device remains on the cooling branch throughout the measurement, the first IV sweep differs systematically from subsequent sweeps.

28787#pg6> This suggests that the first IV induces a non-volatile rearrangement of metallic and insulating domains, which lowers the switching voltage in subsequent cycles <ref:2607. p. 2
Where the paper says it

Even when the device remains on the cooling branch throughout the measurement, the first IV sweep differs systematically from subsequent sweeps. This behavior suggests that the initial switching event redistributes the metallic and insulating domains in a manner which is more conducive to filament formation than the initial domain configuration.

28787#pg6>

Supplementary Information on Defect Modification

Annealing treatments below 400K produced no measurable effect, but annealing at 400K for 10 hours in vacuum produced a mild decrease in the insulating-phase resistance, similar to the change observed after cumulative writing procedure <ref:2607.28787#pg6> The re-emergence of the memory effect after annealing in V2O3 may indicate that annealing not only increases defect concentration but also redistributes them more uniformly throughout the device <ref:2607. p. 5

Where the paper says it

Although this defect concentration is insufficient to significantly reduce the resistance of the insulating phase, it can still facilitate local filament formation at a lower critical voltage. Within this scenario, the memory effect is expected to become stronger at lower temperatures, as the switching voltage increases, thereby enhancing the electric field and the current surge following filament formation.

28787#pg6> This suggests that controlled introduction of defects can be leveraged to tune switching voltage at a pre-chosen operating temperature <ref:2607. p. 9
Where the paper says it

The defect-related low-temperature memory effect is not merely a consequence of the switching process, but can also serve as a practical mechanism for controlling device parameters. The controlled introduction of defects can be leveraged to tune the switching voltage at a pre-chosen operating temperature, even one in which defect-related memory effects are otherwise negligible.

28787#pg6> The defect-related memory effect shares significant similarity with the ’first-firing voltage’ reported in Chalcogenide glasses exhibiting Ovonic switching behavior <ref:2607. p. 9
Where the paper says it

(e-h) The defects based memory - following the first switching event, defects are concentrated in the filament path, lowering the voltage required for the re-creation of the filament. Having established that the low-temperature and phase-coexistence memory effects arise from distinct mechanisms, the remainder of the main text focuses on the defect-related memory effect.

28787#pg6>

Supplementary Information on Structural Memory

The structural memory scenario suggests that the formation of metallic domains within an insulating matrix modifies the local transition temperature at the edges of metallic domains, which may lower the energy barrier for subsequent filament formation <ref:2607.28787#pg6> However, a regime where no memory effect is observed allows us to discount this purely structural explanation for the phenomenon <ref:2607. p. 6

Where the paper says it

At lower temperatures, just below the onset of the hysteresis curve and indicated by the light orange shaded region in Figure 3, there is an intermediate region, where no memory effect is observed in both materials. The existence of such a region allows us to discount the purely structural explanation for the phenomenon (i.

28787#pg6> The results of the experiment reveal three distinct temperature regimes, each characterized by a different memory behavior <ref:2607. p. 6
Where the paper says it

Thus, a memory effect manifested as a decrease in switching voltage cannot be attributed to equilibration but must instead reflect a new metastable state. The results of the experiment, which are shown in Figure 3, reveal three distinct temperature regimes, each characterized by a different memory behavior.

28787#pg6> In the high temperature regime, switching is inherently stochastic and temperature-sensitive, consistent with the redistribution of metallic domains after the first switching event in V2O3 <ref:2607. p. 6
Where the paper says it

In the high temperature regime, which coincides with the phase-coexistence region and is indicated by a light green shaded region in Figure 3, switching is inherently stochastic and temperature-sensitive, because small changes in the domain configuration or measurement temperature can strongly affect the percolation of metallic domains and, consequently, the measured switching voltage [52]. Nevertheless, in V2O3, we observe a memory effect which becomes stronger with increasing temperature.

28787#pg6>

Supplementary Information on Defect Mechanism Details

The defect-related memory effect is understood as part of a broader hierarchy of current surge-induced device modifications, where milder surge magnitudes introduce controllable concentrations of defects <ref:2607.28787#pg6> Oxygen vacancies are the most plausible candidates for these defects in vanadium oxides <ref:2607. p. 0

Where the paper says it

Electrical Control over Volatile Mott Switching through Non-Volatile Memory Effects Amihai Kronman†,1 , Gil Levi†,1 , and Yoav Kalcheim1 1Department of Materials Science and Engineering, Technion - Israel Institute of Technology, Haifa, Israel ABSTRACT Vanadium Dioxide (VO2) and Vanadium Sesquioxide (V2O3) are Mott insulators that undergo an Insulator-to-Metal Transition (IMT) at ∼340K and ∼160K, respectively, manifested as an orders-ofmagnitude reduction in their electrical resistance. These transitions provide the physical basis for their Volatile Resistive Switching (VRS) behavior, making them promising candidates for threshold-switching devices.

28787#pg6> Gradual electroforming may lead to the formation of defective VO2-δ or V2O3-δ phases <ref:2607. p. 1
Where the paper says it

In non-volatile RS devices, the role of electroforming is relatively straightforward: the first sweep creates a conducting filament, whereas from the second sweep onward, only a small region of the filament is ruptured and reconnected [41, 42]. In IMT-based devices, electroforming was also observed, where it introduced substantial structural modifications to the film, including amorphization and the formation of additional oxide phases [38, 43].

28787#pg6> The ability to tune the switching voltage through defect-mediated memory is not necessarily limited to vanadium oxides, suggesting relevance to other Mott insulators such as NbO2 <ref:2607. p. 0
Where the paper says it

Electrical Control over Volatile Mott Switching through Non-Volatile Memory Effects Amihai Kronman†,1 , Gil Levi†,1 , and Yoav Kalcheim1 1Department of Materials Science and Engineering, Technion - Israel Institute of Technology, Haifa, Israel ABSTRACT Vanadium Dioxide (VO2) and Vanadium Sesquioxide (V2O3) are Mott insulators that undergo an Insulator-to-Metal Transition (IMT) at ∼340K and ∼160K, respectively, manifested as an orders-ofmagnitude reduction in their electrical resistance. These transitions provide the physical basis for their Volatile Resistive Switching (VRS) behavior, making them promising candidates for threshold-switching devices.

28787#pg6>

Supplementary Information on Device Protection

The internal resistor configuration reduces the parasitic capacitance directly in parallel with the device, leading to a lower estimated equivalent heating compared to an external series resistor setup <ref:2607.28787#pg6> This reduction is significant, as the characteristic discharge time for V2O3 estimate is much shorter than the thermal timescale of the device <ref:2607. p. 3

Where the paper says it

Voltage (IV) measurements on devices often leads to irreversible damage upon reaching the critical switching voltage (Vsw). Because the formation of the conducting filament occurs on a nanosecondor-less timescale [44–46], far less than the response time of the current source, the voltage remains momentarily pinned at Vsw while the device resistance drops sharply.

28787#pg6> The results demonstrate that a low-temperature writing process can be used to electrically modulate the switching voltage and power of VOx-based devices over a broad temperature range with minimal effect on the HRS/LRS ratio of the device <ref:2607. p. 0
Where the paper says it

Using a protective internal resistor and a multi-step writing protocol, this normally destructive process can be harnessed to tune the switching voltage and power over a wide temperature range. These results demonstrate a route toward controlled programming of switching parameters in IMT-based resistive switching devices.

28787#pg6>

Supplementary Information on Structural Damage

A sudden writing step at 220K produced a markedly different RT curve, where the resistance of both phases increased, including an orders-of-magnitude increase in the metallic-phase resistance <ref:2607.28787#pg6> Microscopic characterization revealed that the larger current surge produces structural damage in the device, leading to cracks oriented parallel to the electrodes <ref:2607.28787#pg6> This drastic change in RT curve after a sudden writing protocol is most likely associated with structural damage rather than the formation of a new, highly resistive oxide phase <ref:2607.28787#pg6> The difference between the device’s state before and after the first IV sweep suggests that the system relaxed into a kinetically favorable metastable state following the first IV sweep <ref:2607. p. 4

Where the paper says it

Notably, this substantial decrease in switching voltage is accompanied by at most a marginal reduction in the insulating phase resistance (See Supplementary section S4), without any visible damage to the device or a significant change to the shape of the R(T) curve, unlike the significant changes observed for conventional electroforming in VOx devices [38, 43]. Such a mild difference between the device’s state before and after the first IV sweep suggests that the system relaxed into a kinetically favorable metastable state following the first IV sweep, though the specific nature of this state is not clear.

28787#pg6>

Supplementary Information on Raman Spectroscopy

Raman measurements, performed using a 532nm laser, showed no significant spectral differences between devices subjected to gradual and sudden writing protocols in VO2 <ref:2607.28787#pg6> In both cases, all observed peaks are consistent with the monoclinic M1 phase of VO2 <ref:2607. p. 1

Where the paper says it

Below the critical temperature (∼160 K), V2O3 is in an insulating antiferromagnetic monoclinic phase, while above this temperature it transforms into a metallic paramagnetic rhombohedral phase [26, 27]. In VO2 the IMT is characterized by up to 4 orders of magnitude change in resistivity, coupled with a structural transition from a low-temperature insulating monoclinic phase to a high-temperature metallic rutile phase [28–30].

28787#pg6> This consistency supports the interpretation that no distinct secondary phase is formed following these protocols <ref:2607.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved AI system can perform predictive modeling of switching voltage based on thermal history by identifying whether a device is in a phase coexistence regime or below it, as this dictates which memory effect occurs.

  2. Improved AI system can differentiate between two distinct memory mechanisms—metallic domain redistribution and defect formation—by analyzing the temperature dependence of the measured voltage change, noting that one is erased by thermal cycling while the other persists at low temperatures.

  3. Improved AI system can implement a controlled programming protocol for switching parameters by utilizing a low-temperature writing process to introduce defects gradually, which allows tuning of switching voltage over a wide temperature range.

  4. Improved AI system can predict the structural consequences of sudden versus gradual current surges during resistive switching, distinguishing between destructive failure (crack formation) and controllable defect introduction based on the surge magnitude.

  5. Improved AI system can optimize device architectures by quantifying the effect of internal resistors, determining that an internal resistor substantially reduces surge-induced damage by approximately a factor of 12 compared to external resistors.

Abstract

Vanadium Dioxide (VO2) and Vanadium Sesquioxide (V2O3) are Mott insulators that undergo an Insulator-to-Metal Transition (IMT) at 340K and 160K, respectively, manifested as an orders-of-magnitude reduction in their electrical resistance. These transitions provide the physical basis for their Volatile Resistive Switching (VRS) behavior, making them promising candidates for threshold-switching devices. Here, we show that the volatile switching in these materials can be strongly affected by non-volatile processes associated with the creation and annihilation of the conducting filament. These processes give rise to pronounced memory effects in which the initial switching voltage substantially exceeds that of subsequent cycles. We identify two distinct mechanisms underlying this behavior in different thermal regimes. In the phase-coexistence regime, a memory effect is observed in V2O3, arising from the spatial redistribution of metallic and insulating domains. Well below the hysteresis regime, an additional electroforming-like memory effect is observed in both VO2 and V2O3 which is attributed to the formation and/or migration of defects under the influence of a high electric field and a current surge associated with the IMT-driven switching. Using a protective internal resistor and a multi-step writing protocol, this normally destructive process can be harnessed to tune the switching voltage and power over a wide temperature range. These results demonstrate a route toward controlled programming of switching parameters in IMT-based resistive switching devices.

Related papers