Ultrashort pulsed laser atmospheric filament properties and microwave radiation inferred from S-band guided wave interaction and self-emission

arXiv:2607.10852 · physics.plasm-ph · Submitted 2026-07-12 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: We're looking at the paper: "Ultrashort pulsed laser atmospheric filament properties and microwave radiation inferred from S-band guided wave interaction and self-emission".

Mira: Here's the gist of the paper. The electrical conductivity of the plasma filament left behind by an ultrashort pulsed laser (USPL) optical pulse after it is geometrically then self-focused in air via the Kerr effect is measured by attenuation of a 3.2 GHz TE10 mode within an S-band waveguide through which the filament passes, taking into account the characteristic radius R of the filament, as determined by fast camera visible light imaging <ref:2607.10852#pg2> The goal of this paper is to infer local and far field properties based on measurements of the characteristic radius R (by visible light imaging), electrical conductivity σ (by interaction of the filament with the TE10 mode of an S-band waveguide) and the total time integral Q of the filament’s axial current (from filament self-emission within the waveguide) over a wide range of background pressures p and distances along such a filament z <ref:2607.10852#pg2> Inferring Filament Parameters The paper details how local and far field properties are inferred by measuring the characteristic radius R, electrical conductivity σ, and the total time integral Q of the filament’s axial current <ref:2607.10852#pg4>.

Kai: The relationship for electrical conductivity is given by σ = σ (n1,n2,T) (assembled from several references) which depends on electron temperature T and the densities ni (i = 1,2) of electrons released from O2 and N2 <ref:2607.10852#pg4>.

Mira: The authors use ionization rates Wi = Wi(I) of O2 and N2 vs.

Kai: local laser intensity I, and electron temperature T = T (I0) vs.

Title and authors: Kai: The paper we are looking at is called "Ultrashort pulsed laser atmospheric filament properties and microwave radiation inferred from S-band guided wave interaction and self-emission". It’s a pretty long title, but it tells you everything we need to know about the main goals.

Mira: Yeah, the authors are Ruden, Wymer, Elle, Englesbe, Lucero, Thornton and Schmitt-Sody. They seem to be pulling together expertise from different areas of plasma physics and experimental optics.

Lev: From what I've read on page one of this paper here, they’re using the electrical conductivity sigma measured by attenuation of a three point two gigahertz TE10 mode in an S band waveguide through which the filament passes, taking into account the characteristic radius R determined by fast camera visible light imaging <ref:2607.10852#pg1,an S band waveguide through which the filament passes, taking into account>.

Kai: Right. So they're measuring that conductivity and using that to get information about the plasma structure, and they’re also getting the radius from a separate visible light measurement on page one of this paper here <ref:2607.10852#pg1>.

Mira: And the big implication here is that they are trying to infer local properties like peak laser intensity I0, electron temperature T, major species particle densities, and that axial current time integral Q after pulse passage.

Lev: That means they're using models for the ionization rates of oxygen and nitrogen versus local laser intensity versus temperature to find those fundamental parameters I0, n1, and T by inverting those conductivity measurements from page four of this paper here <ref:2607.10852#pg2>.

Kai: So that’s where the real work is, using those ionization rates of oxygen and nitrogen versus local laser intensity versus temperature to find those fundamental parameters I0, n1, and T from the conductivity measurements through inversion.

Mira: And they also provide an estimate for the mean postoptical axial electron momentum, pz versus peak laser intensity I0 on page four of this paper here <ref:2607.10852#pg2>. That’s a useful piece of information for understanding how the electrons move after the pulse.

Lev: That means they are using models for the ionization rates of oxygen and nitrogen versus local laser intensity versus temperature to find those fundamental parameters I0, n1, and T by inverting those conductivity measurements from page four of this paper here <ref:2607.10852#pg2>.

Kai: It’s interesting because they mention that the filament is not well-represented by a round cylinder of uniform conductivity in their simulations, suggesting a Gaussian makes a better fit on page four of this paper here <ref:2607.10852#pg2>.

Mira: Right. That's an important caveat because it means the simple model they use isn't perfectly capturing what’s happening physically.

Lev: And that means the real work is using those models for the ionization rates of oxygen and nitrogen versus local laser intensity versus temperature to find those fundamental parameters I0, n1, and T by inverting those conductivity measurements from page four of this paper here <ref:2607.10852#pg2>.

Kai: So, we’re setting up the framework where they measure the electrical conductivity sigma from attenuation of a three point two gigahertz TE10 mode in an S band waveguide through which the filament passes, taking into account the characteristic radius R determined by fast camera visible light imaging <ref:2607.10852#pg1,an S band waveguide through which the filament passes, taking into account>.

Mira: That's how they are setting up the framework where they measure the electrical conductivity sigma from attenuation of a three point two gigahertz TE10 mode in an S band waveguide through which the filament passes, taking into account the characteristic radius R determined by fast camera visible light imaging <ref:2607.10852#pg1,an S band waveguide through which the filament passes, taking into account>.

Lev: And we need to remember that we're looking at how they use those models for the ionization rates of oxygen and nitrogen versus local laser intensity versus temperature to find those fundamental parameters I0, n1, and T by inverting those conductivity measurements from page four of this paper here <ref:2607.10852#pg2>.

Kai: And that means they are using models for the ionization rates of oxygen and nitrogen versus local laser intensity versus temperature to find those fundamental parameters I0, n1, and T by inverting those conductivity measurements from page four of this paper here <ref:2607.10852#pg2>.

The paper's summary: Kai: Okay, so let's talk about what they actually did in the paper. They are using measurements to measure that electrical conductivity sigma from attenuation of a three point two gigahertz TE10 mode in an S band waveguide through which the filament passes, taking into account the characteristic radius R determined by fast camera visible light imaging <ref:2607.10852#pg1,an S band waveguide through which the filament passes, taking into account>.

Mira: And they are also getting that characteristic radius R from a separate visible light measurement on page one of this paper here, and then they use that conductivity to infer local properties like peak laser intensity I0, electron temperature T, major species particle densities, and the axial current time integral Q <ref:2607.10852#pg1,T$, major species particle densities, and>.

Lev: And they are using models for the ionization rates of oxygen and nitrogen versus local laser intensity versus temperature to find those fundamental parameters I0, n1, and T by inverting those conductivity measurements from page four of this paper here <ref:2607.10852#pg2>.

Mira: And they use the self-emission signal within the waveguide to determine that total time integral Q over a wide range of background pressures and distances z along such a filament where z is less than some value mentioned on page two <ref:2607.10852#pg2>.

Kai: So, they’re using models for the ionization rates of oxygen and nitrogen versus local laser intensity versus temperature to find those fundamental parameters I0, n1, and T by inverting those conductivity measurements from page four of this paper here <ref:2607.10852#pg2>.

Kai: They are using models for the ionization rates of oxygen and nitrogen versus local laser intensity versus temperature to find those fundamental parameters I0, n1, and T by inverting those conductivity measurements from page four of this paper here <ref:2607.10852#pg2>.

The paper's improvements: Kai: Now, moving into the improvements they suggest, they suggest using this framework to compare theoretical far field microwave radiation patterns due to axial current variation Q with published measurements.

Mira: They are using the measurement of that total time integral Q over a wide range of background pressures and distances z along such a filament where z is less than some value mentioned on page two to model the far field radiation as a collective effect of the entire filament with principle frequency f1 <ref:2607.10852#pg2>.

Lev: And they are using that measurement of that total time integral Q over a wide range of background pressures and distances z along such a filament where z is less than some value mentioned on page two to model the far field radiation as a collective effect of the entire filament with principle frequency f1 <ref:2607.10852#pg2>.

Kai: This modeling shows that the resulting electric field E0 theta decreases rapidly with increasing theta until theta equals sixty degrees where it crosses zero, and doesn’t rise significantly beyond that.

Mira: That means that the value of nu = nu max that results in K R with this minimum angle equal to K0, which is defined as the integral of U0 over z, corresponds to the full conversion of laser-imparted center of mass kinetic energy to radiation with theta greater than or equal to that minimum angle.

Lev: And they also show that this value nu = nu max results in K R with this minimum angle equal to K0, which is defined as the integral of U0 over z, corresponds to the full conversion of laser-imparted center of mass kinetic energy to radiation with theta greater than or equal to that minimum angle.

Kai: It seems like they're using this relationship between nu = nu max and the minimum angle, theta min, which is what links all these pieces together.

Kai: And they also show that this value nu = nu max results in K R with this minimum angle equal to K0, which is defined as the integral of U0 over z.

Mira: And they are using the measurement of that total time integral Q over a wide range of background pressures and distances z along such a filament where z is less than some value mentioned on page two to model the far field radiation as a collective effect of the entire filament with principle frequency f1 <ref:2607.10852#pg2>.

Kai: It sounds like they're using this relationship between nu = nu max and the minimum angle, theta min, which is what links all these pieces together.

Conclusion: Mira: So, to wrap up on the paper "Ultrashort pulsed laser atmospheric filament properties and microwave radiation inferred from S-band guided wave interaction and self-emission". They’re showing that the Q measurement, which serves as the basis for Equation thirty-five may be considered accurate for values of nu as low as nu max since it is an S band diagnostic.

Kai: And they also note that the correlation of experimental VR is very good up to t1 = one point four nanoseconds, so this value is used for the integration limit there.

Lev: From an engineering perspective, it’s important to remember that the Q measurement, which serves as the basis for Equation thirty-five may be considered accurate for values of nu as low as nu max since it is an S band diagnostic.

Kai: They also say that the comparison of Figure fifteen to Figure E3a suggests that the former represents a baseline response of the far field to the wake field current that explicitly neglects the oscillatory modes recorded by the latter.

Mira: And they note that this neglect means there might be greater undershoot or slow oscillation during subsequent decay not being present in our model.

Kai: And they also say that this neglect means there might be greater undershoot or slow oscillation during subsequent decay not being present in our model.

Mira: So, the paper "Ultrashort pulsed laser atmospheric filament properties and microwave radiation inferred from S-band guided wave interaction and self-emission" gives us a way to look at these plasma filaments not just as transient events, but to really map out their physical properties and what they radiate into space.

Lev: And this framework is useful for connecting the local physics inside the plasma, like temperature and density, to what we measure externally in a waveguide.

Kai: Yeah, that's the big picture here; understanding how those things are related across different scales.

Air Force Research Laboratory

physics.plasm-ph

Submitted: 2026-07-12

Updated: 2026-11-11

Comments: 19 pages, 30 figures/subfigures. Phys. Plasmas, submitted

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 73/100

The gist: The electrical conductivity of the plasma filament left behind by an ultrashort pulsed laser (USPL) optical pulse after it is geometrically then self-focused in air via the Kerr effect is measured by…

Key concepts

Characteristic Radius R
This is the physical size of the plasma filament created by the laser pulse. It is measured using visible light imaging, providing a spatial constraint on the plasma structure. The paper notes that a Gaussian shape fits better than a simple cylinder model.
Electrical Conductivity $\sigma$
The conductivity of the filament is determined by observing how it attenuates an S-band waveguide mode. This measurement is used to infer local electron temperature (T) and densities ($n_1, n_2$) through established physical models linking these properties to the measured attenuation.
Total Time Integral Q
Q represents the total time integral of the filament's axial current, derived from self-emission within the waveguide. This value is crucial for modeling radiation. Comparing different estimates of Q helps determine the filament's current decay rate ($\nu$) and its effect on far-field radiation.
Far Field Radiation Analysis
The paper models the far-field electric field ($E_{0\theta}$) radiated by the filament as a collective effect. This analysis links the measured Q(z) to radiation patterns, helping to determine parameters like $\nu_{max}$ that describe how laser energy is converted into microwave radiation.

Terminology

Summary

The electrical conductivity of the plasma filament left behind by an ultrashort pulsed laser (USPL) optical pulse after it is geometrically then self-focused in air via the Kerr effect is measured by attenuation of a 3. p. 0

Where the paper says it

Thornton,1 and A. Schmitt-Sody1 Air Force Research Laboratory, Directed Energy Directorate (Date textdate; Received textdate; Revised textdate; Accepted textdate; Published textdate) The electrical conductivity σ of the plasma filament left behind by an ultrashort pulsed laser (USPL) optical pulse after it is geometrically then self-focused in air via the Kerr effect is measured by attenuation of a 3.

2 GHz TE10 mode within an S-band waveguide through which the filament passes, taking into account the characteristic radius R of the filament, as determined by fast camera visible light imaging <ref:2607. p. 0
Where the paper says it

Schmitt-Sody1 Air Force Research Laboratory, Directed Energy Directorate (Date textdate; Received textdate; Revised textdate; Accepted textdate; Published textdate) The electrical conductivity σ of the plasma filament left behind by an ultrashort pulsed laser (USPL) optical pulse after it is geometrically then self-focused in air via the Kerr effect is measured by attenuation of a 3. 2 GHz TE10 mode within an S-band waveguide through which the filament passes, taking into account the characteristic radius R of the filament, as determined by fast camera visible light imaging.

10852#pg2> The goal of this paper is to infer local and far field properties based on measurements of the characteristic radius R (by visible light imaging), electrical conductivity σ (by interaction of the filament with the TE10 mode of an S-band waveguide) and the total time integral Q of the filament’s axial current (from filament self-emission within the waveguide) over a wide range of background pressures p and distances along such a filament z <ref:2607. p. 0
Where the paper says it

The radiation pattern is found to be rotationally symmetric about the laser propagation (z) axis, implying an axial current source. The goal of this paper is to infer local and far field properties based on measurements of the characteristic radius R (by visible light imaging), electrical conductivity σ (by interaction of the filament with the TE10 mode of an S-band waveguide9 ), and the total time integral Q of the filament’s axial current (from filament self-emission within the waveguide) over a wide range of background pressures p and distances along such a filament z.

10852#pg2>

Inferring Filament Parameters

The paper details how local and far field properties are inferred by measuring the characteristic radius R, electrical conductivity σ, and the total time integral Q of the filament’s axial current <ref:2607.10852#pg4>. The relationship for electrical conductivity is given by σ = σ (n1,n2,T) (assembled from several references) which depends on electron temperature T and the densities ni (i = 1,2) of electrons released from O2 and N2 <ref:2607. p. 0

Where the paper says it

The filamentation process is unstable10, resulting in the laser intensity within to be difficult to determine. The relationship σ = σ (n1,n2,T) (assembled from several references1112131415) depends on electron temperature T and the densities ni (i = 1,2) of electrons released from O2 and N2, respectively, for a given initial neutral density n0 (single ionization and net charge neutrality are assumed).

10852#pg4>. The authors use ionization rates Wi = Wi(I) of O2 and N2 vs. p. 0
Where the paper says it

The relationship σ = σ (n1,n2,T) (assembled from several references1112131415) depends on electron temperature T and the densities ni (i = 1,2) of electrons released from O2 and N2, respectively, for a given initial neutral density n0 (single ionization and net charge neutrality are assumed). In conjunction with the ionization rates Wi = Wi(I) of O2 and N2 16 vs.

local laser intensity I, and electron temperature T = T (I0) vs. p. 0
Where the paper says it

Models of the major air constituents’ ionization rate Wi vs. local laser intensity I, and of temperature T and mean axial electron momentum ⟨pz⟩ vs.

peak intensity I0 to find I0, ni, and T along the filament from the σ measurements by inversion <ref:2607. p. 0
Where the paper says it

local instantaneous intensity I and electron temperature T = T (I0) vs. peak intensity I0 upon electron thermalization17, we find I0, ni , and T along the filament from the σ measurements by inversion.

10852#pg4>. The model also provides an estimate of mean postoptical axial electron momentum ⟨pz⟩ vs. p. 0
Where the paper says it

I = I(t) is assumed to have a Gaussian time dependence with the measured pulse width for this. The T (I0) model also provides an estimate of mean postoptical axial electron momentum ⟨pz⟩ vs.

I0 <ref:2607. p. 0
Where the paper says it

L , here, is the filament length and θ is emission angle. The total energy radiated due to the directly measured Q(z) far exceeds the laser-imparted center of mass electron arXiv:2607.

10852#pg4>.

Diagnostic Measurements and Calibration

The measurement of the TE10 power attenuation factor A involves recording output power PR vs. time t averaged over 50 shots with and without a filament and with and without 3. p. 1

Where the paper says it

The coax adapter at one end of the waveguide is used as a receiver (R) to record output power PR vs. time t averaged over 50 shots with and without a filament and with and without 3.

2 GHz TE10 mode excitation <ref:2607. p. 1
Where the paper says it

time t averaged over 50 shots with and without a filament and with and without 3. 2 GHz TE10 mode excitation coming from a transmitter with input impedance R0 attached to an identical adapter at the other end.

10852#pg5>. The input to a Hewlett Packard 8470B crystal detector has an output voltage VD proportional to the negative of the receiver’s CW power PR <ref:2607. p. 1
Where the paper says it

This is subtracted from the signal with the drive on to isolate the signal that results from TE10 mode attenuation due to the filament. The input to a Hewlett Packard 8470B crystal detector18 with input impedance R0 and nominal output shunt capacitance C0 = 30 pF is attached to the receiver output for the power measurement.

10852#pg5>. The parameter A is defined as the factor by which the HP power detector signal VD is reduced in peak amplitude due to absorption and reflection of the TE10 mode transmitted from the other end of the waveguide due to the filament’s resistive and inductive impedance <ref:2607. p. 2
Where the paper says it

distance z from the focusing mirror for a range of p values. Parameter A is the factor by which the HP power detector signal VD is reduced in peak amplitude due to absorption and reflection of the TE10 mode transmitted from the other end of the waveguide due to the filament’s resistive and inductive impedance.

10852#pg5>.

Radius Determination via Imaging

The characteristic radius R is estimated using visible light imaging, where a 4 Quik E-Dig from Stanford Computer Optics, Inc. with an S-20 spectral response and 8. p. 3

Where the paper says it

A 4 Quik E-Dig from Stanford Computer Optics, Inc. with an S-20 spectral response and 8.

3 µm square image (sensor) pixel size is used <ref:2607. p. 3
Where the paper says it

with an S-20 spectral response and 8. 3 µm square image (sensor) pixel size is used for this.

10852#pg5>. The general purpose resolution of isolated features is roughly s1 ≈ 15 µm (5 pixels), based the distance required for the calibration lines to make an intensity transition midway between lines that is 50% of the peak-to-peak range <ref:2607. p. 3
Where the paper says it

The chart is placed inside the quartz tube for this measurement to take into account minor cylindrical lensing, and to assess the tube’s effect on resolution. General purpose resolution of isolated features is roughly s1 ≈ 15 µm (5 pixels), based the distance required for the calibration lines to make an intensity transition midway between lines that is 50% of the peak-to-peak range.

10852#pg5>. The filament is not well-represented by the round cylinder of uniform conductivity of the simulations, and a Gaussian makes a better fit <ref:2607. p. 3
Where the paper says it

The filament is not well-represented by the round cylinder of uniform conductivity of the simulations. A Gaussian makes a better fit.

10852#pg5>.

Conductivity and Density Modeling

The peak free electron densities n1 = n1 (I0) released from O2 and n2 = n2 (I0) released from N2 and peak electron temperature T = T (I0) all as functions of peak laser intensity I0 permit these properties to be determined from the σ measurements, given a model of σ = σ (n1,n2,T) <ref:2607.10852#pg5>. The ionization rates Wi(I) for the two species are determined by inversion of time of flight spectrometer measurements of ion count <ref:2607. p. 5

Where the paper says it

I0 for a range of USPL pulse widths in air with FWHM specified in the legend, based on Eqs. Local ionization rates Wi(I) for the two species are determine by inversion of time of flight spectrometer measurements of ion count16.

10852#pg5>. The real component of σ assumed is σ = e squared (n1+n2) mνc,eff <ref:2607. p. 6
Where the paper says it

To this end, the real component of σ assumed is11:22. 25 , σ = e 2 (n1+n2) mνc,eff νc = 3 ∑ i=1 νci 1 νc,eff = 8 3 √ π m 2kBT 5/2 R ∞ 0 v 4νc ν 2 c +ω2 exp − mv2 2kBT dv νci = v (ni0 −ni)qi(v), i = 1,2 νc3 = v (n1 +n2)q3 (v) (12) where e is fundamental charge, m is electron mass, kB the Boltzmann constant, and ω = ω10 for the S-band conductivity measurement.

10852#pg5>.

Charge Transfer and Decay Rate Estimation

The total time integral Q is determined from the self-emission signal, where the experimental value of Q is Q50 = 0.93 pC <ref:2607. p. 0

Where the paper says it

L , here, is the filament length and θ is emission angle. The total energy radiated due to the directly measured Q(z) far exceeds the laser-imparted center of mass electron arXiv:2607.

10852#pg5>. One estimate of ν = ν1 is found by assuming the near field energy is the minimum consistent with Maxwell’s equations and a generalized form of Ohm’s law <ref:2607. p. 9
Where the paper says it

t = 0 is the time of optical pulse passage in this section. One estimate of ν = ν1 is found by assuming the near field energy is the minimum consistent with Maxwell’s equations and the following electron momentum equation, based on a generalized form of Ohm’s law33 , E = J σ + m e 2nR ∂J ∂t + 1 en (J×B−∇pe) (17) where pe is electron pressure.

10852#pg5>. A complementary decay rate ν = ν0 suggested by 3-D time domain simulations is found by assuming the current and, therefore, the near field it produces, is expelled to the periphery of the filament during thermalization <ref:2607. p. 0
Where the paper says it

An independent direct measurement of Q based on filament self-emission is presented for comparison. The latter Q, in addition to the σ and R measurements, provide a estimate of steady state ν = ν0 under the complementary assumption that If is driven to the surface during the energy conversion process, and the associated EM field diffuses back in during decay.

10852#pg5>.

Far Field Radiation Analysis

The far field radiation from Q = Q(z) is modeled as a collective effect of the entire filament with principle frequency f1 = c/(2L(1−cosθ)) for which Q = Q(z) <ref:2607.10852#pg5>. The resulting electric field E0θ decreases rapidly with increasing θ until θ = 60◦, where it crosses zero, and doesn’t rise significantly beyond that <ref:2607.10852#pg5>. The value of ν = νmax that results in KR with this θmin equal to K0, the latter defined as the integral of U0 = λII squared f0 over z, corresponds to the full conversion of laser-imparted center of mass kinetic energy to radiation with θ ≥ θmin <ref:2607. p. 9

Where the paper says it

5401ni , i = 1,2 (16) Here, we have assumed the same Gaussian profile for ni , as we did for σ (r) and J (r) to determine the corresponding uniform nRi (analogous to Eq. From this, the post-optical center-ofmass electron kinetic energy per unit length imparted by the laser is expressed as U0 = λII 2 f0, where λI is defined in Eqs.

p. 9
Where the paper says it

5401ni , i = 1,2 (16) Here, we have assumed the same Gaussian profile for ni , as we did for σ (r) and J (r) to determine the corresponding uniform nRi (analogous to Eq. From this, the post-optical center-ofmass electron kinetic energy per unit length imparted by the laser is expressed as U0 = λII 2 f0, where λI is defined in Eqs.

10852#pg5>.

Discussion and Conclusions

The primary purpose of this paper is to provide experimental results for use as benchmarks for 3-D time domain simulations of the filamentation and radiation process <ref:2607.10852#pg5>. The Q(z) measurement, which serves as the basis for Eq. p. 3

Where the paper says it

transverse distance x showing several filaments and their Gaussian fits (b). Visible light imaging of the filament taken at a range of distances z from the focusing mirror provides the basis for estimating an effective value of R for use with the G(A,R) calibration table to determine G.

p. 3
Where the paper says it

transverse distance x showing several filaments and their Gaussian fits (b). Visible light imaging of the filament taken at a range of distances z from the focusing mirror provides the basis for estimating an effective value of R for use with the G(A,R) calibration table to determine G.

p. 3
Where the paper says it

transverse distance x showing several filaments and their Gaussian fits (b). Visible light imaging of the filament taken at a range of distances z from the focusing mirror provides the basis for estimating an effective value of R for use with the G(A,R) calibration table to determine G.

p. 3
Where the paper says it

transverse distance x showing several filaments and their Gaussian fits (b). Visible light imaging of the filament taken at a range of distances z from the focusing mirror provides the basis for estimating an effective value of R for use with the G(A,R) calibration table to determine G.

35, may be considered accurate for values of ν as low as νmax since it is an S-band diagnostic <ref:2607.10852#pg5>. The correlation of experimental VR is very good up to t1 = 1. p. 8
Where the paper says it

1), but not Q itself, since K cancels out in the ratio. The correlation of experimental VR is very good up to t1 = 1.

p. 8
Where the paper says it

1), but not Q itself, since K cancels out in the ratio. The correlation of experimental VR is very good up to t1 = 1.

4 ns, so this value is used for the integration limit <ref:2607. p. 8
Where the paper says it

The correlation of experimental VR is very good up to t1 = 1. 4 ns, so this value is used for the integration limit.

p. 8
Where the paper says it

The correlation of experimental VR is very good up to t1 = 1. 4 ns, so this value is used for the integration limit.

10852#pg5>. The Q(z) measurement, which serves as the basis for Eq. 35, may be considered accurate for values of ν as low as νmax since it is an S-band diagnostic <ref:2607.10852#pg5>.

Appendix Details

The diagnostic calibration simulations are performed using 3-D continuous wave COMSOL MultiphysicsTM electromagnetic (EM) simulations <ref:2607.10852#pg5>. The simulation mesh is tetrahedral, except for the PML and filament, as described <ref:2607. p. 1

Where the paper says it

This self-emission signal is also used to measure Q. To calibrate it, a unipolar current pulse with a Gaussian time history with a short standard deviation (5 ps) relative to S-band is sent through the filament in the direction of the laser pulse in a time domain simulation of the waveguide geometry similar to that described above, but with no TE10 driver.

10852#pg5>. The validation compares the theoretical values of A for several cases of actual uniform solid conducting filaments with measured values of R and σ of the same length as modeled <ref:2607.10852#pg5>. The self-emission simulation uses a negative going Gaussian I0 (t) with a (very short) 5 ps standard deviation width and a total time integral of Qsim = −1 pC <ref:2607. p. 8
Where the paper says it

This, we will see, is a small radius relative to that measured, but with a comparable value of G. The simulation uses a negative going Gaussian I0 (t) with a (very short) 5 ps standard deviation width and a total time integral of Qsim = −1 pC.

10852#pg5>.

Table Summary

Table 2 Parameters are tabulated at axial locations z = z1, where our independent estimates of filament current time integral Q from direct measurement (Eq. 15) and resistive decay (If from Eq. p. 1

Where the paper says it

The interaction of the filament with a 3. 2 GHz TE10 mode driven at one end of the waveguide and received at the other has both resistive (dissipative) and inductive (reactive) contributions.

24 divided by ν1 from Eq. p. 2
Where the paper says it

2 GHz drive on (bottom), selfemission of the filament only (top), and the difference (middle). Parameter A is the peak of the latter divided by its initial value.

21) are equal <ref:2607. p. 0
Where the paper says it

L , here, is the filament length and θ is emission angle. The total energy radiated due to the directly measured Q(z) far exceeds the laser-imparted center of mass electron arXiv:2607.

10852#pg5>. The results for ν = νmax results in a reasonably good Eθpp match with Englebe’s data considering that νmax is only an upper bound <ref:2607. p. 1
Where the paper says it

2 kinetic energy K0 available to produce it for either ν = ν0 or ν = ν1, except for the lowest p. A much lower upper bound on ν = νmax, which assumes 100% conversion, results in a radiation pattern similar to published measurements2 taken with the same equipment and geometry, albeit with a laser pulse energy of 40 mJ instead of our 30 mJ.

10852#pg5>. The comparison of Fig. p. 8
Where the paper says it

9 suitable for comparison with the simulations was obtained at p = 50 Torr near the center of the filament (z = 307 cm) by averaging over 200 shots. VR after 3 ns, as plotted in Fig.

p. 8
Where the paper says it

9 suitable for comparison with the simulations was obtained at p = 50 Torr near the center of the filament (z = 307 cm) by averaging over 200 shots. VR after 3 ns, as plotted in Fig.

p. 8
Where the paper says it

9 suitable for comparison with the simulations was obtained at p = 50 Torr near the center of the filament (z = 307 cm) by averaging over 200 shots. VR after 3 ns, as plotted in Fig.

15 to Fig. E3a suggests the former represents a baseline response of the far field to the wake field current that explicitly neglects the oscillatory modes recorded by the latter <ref:2607.10852#pg5>. The initial fast rise and fall to zero at θ = 15◦ for all p seen in Fig. p. 5
Where the paper says it

The detailed steps are specified in the caption to Fig. ni(I0) for i = 1,2 are found from the optical-cycle averaged ionization rates’ dependence on local intensity I for air’s main constituents N2 and O2 16 as the post-optical solutions to ∂ni/∂t = (ni0 −ni)Wi(I), where Wi(I) is the optical-cycle averaged ionization rate (⟨W⟩γ in this reference), and ni0 is the initial density of that species’ neutral molecule.

p. 5
Where the paper says it

The detailed steps are specified in the caption to Fig. ni(I0) for i = 1,2 are found from the optical-cycle averaged ionization rates’ dependence on local intensity I for air’s main constituents N2 and O2 16 as the post-optical solutions to ∂ni/∂t = (ni0 −ni)Wi(I), where Wi(I) is the optical-cycle averaged ionization rate (⟨W⟩γ in this reference), and ni0 is the initial density of that species’ neutral molecule.

p. 5
Where the paper says it

The detailed steps are specified in the caption to Fig. ni(I0) for i = 1,2 are found from the optical-cycle averaged ionization rates’ dependence on local intensity I for air’s main constituents N2 and O2 16 as the post-optical solutions to ∂ni/∂t = (ni0 −ni)Wi(I), where Wi(I) is the optical-cycle averaged ionization rate (⟨W⟩γ in this reference), and ni0 is the initial density of that species’ neutral molecule.

E3a takes 33 ps, very similar to that seen in our Fig. p. 2
Where the paper says it

Parameter A is the factor by which the HP power detector signal VD is reduced in peak amplitude due to absorption and reflection of the TE10 mode transmitted from the other end of the waveguide due to the filament’s resistive and inductive impedance. Correcting for self-emission takes into account the random phase of the TE10 mode when the laser fires.

p. 2
Where the paper says it

Parameter A is the factor by which the HP power detector signal VD is reduced in peak amplitude due to absorption and reflection of the TE10 mode transmitted from the other end of the waveguide due to the filament’s resistive and inductive impedance. Correcting for self-emission takes into account the random phase of the TE10 mode when the laser fires.

p. 2
Where the paper says it

Parameter A is the factor by which the HP power detector signal VD is reduced in peak amplitude due to absorption and reflection of the TE10 mode transmitted from the other end of the waveguide due to the filament’s resistive and inductive impedance. Correcting for self-emission takes into account the random phase of the TE10 mode when the laser fires.

15 <ref:2607. p. 0
Where the paper says it

L , here, is the filament length and θ is emission angle. The total energy radiated due to the directly measured Q(z) far exceeds the laser-imparted center of mass electron arXiv:2607.

p. 0
Where the paper says it

L , here, is the filament length and θ is emission angle. The total energy radiated due to the directly measured Q(z) far exceeds the laser-imparted center of mass electron arXiv:2607.

p. 0
Where the paper says it

L , here, is the filament length and θ is emission angle. The total energy radiated due to the directly measured Q(z) far exceeds the laser-imparted center of mass electron arXiv:2607.

10852#pg5>. The wide band response of Fig. p. 0
Where the paper says it

The radiation pattern is found to be rotationally symmetric about the laser propagation (z) axis, implying an axial current source. The goal of this paper is to infer local and far field properties based on measurements of the characteristic radius R (by visible light imaging), electrical conductivity σ (by interaction of the filament with the TE10 mode of an S-band waveguide9 ), and the total time integral Q of the filament’s axial current (from filament self-emission within the waveguide) over a wide range of background pressures p and distances along such a filament z.

E3C (θ = 15◦) is consistent with Fig. p. 9
Where the paper says it

t = 0 is the time of optical pulse passage in this section. One estimate of ν = ν1 is found by assuming the near field energy is the minimum consistent with Maxwell’s equations and the following electron momentum equation, based on a generalized form of Ohm’s law33 , E = J σ + m e 2nR ∂J ∂t + 1 en (J×B−∇pe) (17) where pe is electron pressure.

p. 9
Where the paper says it

t = 0 is the time of optical pulse passage in this section. One estimate of ν = ν1 is found by assuming the near field energy is the minimum consistent with Maxwell’s equations and the following electron momentum equation, based on a generalized form of Ohm’s law33 , E = J σ + m e 2nR ∂J ∂t + 1 en (J×B−∇pe) (17) where pe is electron pressure.

15 (f1 is near the middle in the FFT spectrum) <ref:2607.10852#pg5>. The correlation of experimental VR is very good up to t1 = 1.4 ns, so this value is used for the integration limit <ref:2607.10852#pg5>. The Q(z) measurement, which serves as the basis for Eq. 35, may be considered accurate for values of ν as low as νmax since it is an S-band diagnostic <ref:2607.10852#pg5>. The Q = If/ν1 using Eq. p. 3
Where the paper says it

A Gaussian makes a better fit. Multiline Gaussian fits using parameters iterated by hand are overlaid in Fig.

p. 3
Where the paper says it

A Gaussian makes a better fit. Multiline Gaussian fits using parameters iterated by hand are overlaid in Fig.

p. 3
Where the paper says it

A Gaussian makes a better fit. Multiline Gaussian fits using parameters iterated by hand are overlaid in Fig.

21 and Eq. 24 being similar (within a factor of ∼ 2) to the self-emission measurement (Fig. p. 1
Where the paper says it

This self-emission signal is also used to measure Q. To calibrate it, a unipolar current pulse with a Gaussian time history with a short standard deviation (5 ps) relative to S-band is sent through the filament in the direction of the laser pulse in a time domain simulation of the waveguide geometry similar to that described above, but with no TE10 driver.

p. 1
Where the paper says it

This self-emission signal is also used to measure Q. To calibrate it, a unipolar current pulse with a Gaussian time history with a short standard deviation (5 ps) relative to S-band is sent through the filament in the direction of the laser pulse in a time domain simulation of the waveguide geometry similar to that described above, but with no TE10 driver.

p. 1
Where the paper says it

This self-emission signal is also used to measure Q. To calibrate it, a unipolar current pulse with a Gaussian time history with a short standard deviation (5 ps) relative to S-band is sent through the filament in the direction of the laser pulse in a time domain simulation of the waveguide geometry similar to that described above, but with no TE10 driver.

13) suggests that the mechanism has little effect on Q itself, such as a linear convolution like the one that results in Eθ (Eq. p. 9
Where the paper says it

Such a term contributes to oscillatory Sommerfeld wire surface modes34:6. 6 that have little effect on total charge transfer due to the monotonically decaying current of interest here.

p. 9
Where the paper says it

Such a term contributes to oscillatory Sommerfeld wire surface modes34:6. 6 that have little effect on total charge transfer due to the monotonically decaying current of interest here.

p. 9
Where the paper says it

Such a term contributes to oscillatory Sommerfeld wire surface modes34:6. 6 that have little effect on total charge transfer due to the monotonically decaying current of interest here.

34) <ref:2607. p. 0
Where the paper says it

L , here, is the filament length and θ is emission angle. The total energy radiated due to the directly measured Q(z) far exceeds the laser-imparted center of mass electron arXiv:2607.

p. 0
Where the paper says it

L , here, is the filament length and θ is emission angle. The total energy radiated due to the directly measured Q(z) far exceeds the laser-imparted center of mass electron arXiv:2607.

p. 0
Where the paper says it

L , here, is the filament length and θ is emission angle. The total energy radiated due to the directly measured Q(z) far exceeds the laser-imparted center of mass electron arXiv:2607.

10852#pg5>. The contour plots of Fig. p. 4
Where the paper says it

6 Contour plots of composites of the image line-outs from at all z locations and all pressures p studied. The solid line tracks the peak intensity vs.

p. 4
Where the paper says it

6 Contour plots of composites of the image line-outs from at all z locations and all pressures p studied. The solid line tracks the peak intensity vs.

p. 4
Where the paper says it

6 Contour plots of composites of the image line-outs from at all z locations and all pressures p studied. The solid line tracks the peak intensity vs.

6 provide a degree of corroboration <ref:2607.10852#pg5>. The following issues may account for the generally lower experimental Eθpp: K0 may be diverted to other processes, such as Ohmic heating and θ. p. 0
Where the paper says it

The two estimates are in reasonable agreement despite the fact that ν, based on the following, is generally much lower. 1 Photograph of experimental hardware showing laser beam entry window on left and a pressure controlled volume within joined fused quartz tubes, with the small one passing through the diagnostic waveguide.

p. 0
Where the paper says it

The two estimates are in reasonable agreement despite the fact that ν, based on the following, is generally much lower. 1 Photograph of experimental hardware showing laser beam entry window on left and a pressure controlled volume within joined fused quartz tubes, with the small one passing through the diagnostic waveguide.

The isolated primary filament assumption is not valid in many z locations, while K0 (as a collective property) assumes it is <ref:2607.10852#pg5>. The uniform cylinder approximation used to represent a Gaussian distribution to calibrate the Sband instrument is imprecise <ref:2607.10852#pg5>. The horns used to measure Eθ are dispersive with a frequency-dependent sensitivity, which alters the signal waveform, potentially lowering Eθpp <ref:2607.10852#pg5>. Reflection and refraction through the quartz tube has a ∼ 10% effect in terms of reducing the experimental Eθpp at θ = 15◦ <ref:2607. p. 3
Where the paper says it

04 µm based on a numerical analysis of several 1951 USAF Resolution Test Chart images, implying magnification M = 2. The chart is placed inside the quartz tube for this measurement to take into account minor cylindrical lensing, and to assess the tube’s effect on resolution.

p. 3
Where the paper says it

04 µm based on a numerical analysis of several 1951 USAF Resolution Test Chart images, implying magnification M = 2. The chart is placed inside the quartz tube for this measurement to take into account minor cylindrical lensing, and to assess the tube’s effect on resolution.

10852#pg5>. The comparison of Fig. 15 to Fig. E3a suggests that the former represents a baseline response of the far field to the wake field current that explicitly neglects the oscillatory modes recorded by the latter <ref:2607.10852#pg5>. The initial fast rise and fall to zero at θ = 15◦ for all p seen in Fig. E3a takes 33 ps, very similar to that seen in our Fig. 15 <ref:2607.10852#pg5>. The greater undershoot (aka “ring”) of the former and slow oscillation during subsequent decay not being present in our model may be attributed to our neglect of oscillatory current modes (such as those recorded by Zhou38 <ref:2607.10852#pg5>. The horn dispersion may also contribute to the oscillation <ref:2607.10852#pg5>. The FFT-based results presented, the wide band response of Fig. p. 0
Where the paper says it

The radiation pattern is found to be rotationally symmetric about the laser propagation (z) axis, implying an axial current source. The goal of this paper is to infer local and far field properties based on measurements of the characteristic radius R (by visible light imaging), electrical conductivity σ (by interaction of the filament with the TE10 mode of an S-band waveguide9 ), and the total time integral Q of the filament’s axial current (from filament self-emission within the waveguide) over a wide range of background pressures p and distances along such a filament z.

E3C (θ = 15◦) is consistent with Fig. 15 (f1 is near the middle in the FFT spectrum) <ref:2607.10852#pg5>. A similar correlation is apparent for other angles too <ref:2607.10852#pg5>. f1 = 3, 6 and 9 GHz occur at θ = 33. p. 0
Where the paper says it

Schmitt-Sody1 Air Force Research Laboratory, Directed Energy Directorate (Date textdate; Received textdate; Revised textdate; Accepted textdate; Published textdate) The electrical conductivity σ of the plasma filament left behind by an ultrashort pulsed laser (USPL) optical pulse after it is geometrically then self-focused in air via the Kerr effect is measured by attenuation of a 3. 2 GHz TE10 mode within an S-band waveguide through which the filament passes, taking into account the characteristic radius R of the filament, as determined by fast camera visible light imaging.

6◦, 23.6◦, and 19.2◦ in our model, respectively <ref:2607. p. 0
Where the paper says it

L , here, is the filament length and θ is emission angle. The total energy radiated due to the directly measured Q(z) far exceeds the laser-imparted center of mass electron arXiv:2607.

10852#pg5>. These are comparable to the mean θ of the Eθ FFT distribution FE (θ) plotted in Fig. p. 5
Where the paper says it

z for the filament may be estimated in terms of G from the G(A,R) calibration matrix plotted in of Fig. A6 by assuming σ (r) too has a Gaussian distribution with standard deviation s, σ (r) = σ (0)exp − r 2 2s 2 (9) This is justified since it results in a uniform E field, based on Ohm’s law.

E5 for these frequencies: ⟨θ⟩ = 31. p. 6
Where the paper says it

For our σ (n1,n2,T) expression, consideration is needed to take into account the sum22:22 23:2. 31 of the electron momentum transfer collision frequencies νc 22:2 vs.

1±1.5◦, 22.3±0.6◦, and 20.6±2.6◦, respectively <ref:2607. p. 0
Where the paper says it

L , here, is the filament length and θ is emission angle. The total energy radiated due to the directly measured Q(z) far exceeds the laser-imparted center of mass electron arXiv:2607.

10852#pg5>. The value of ν = νmax that results in KR with this θmin equal to K0, the latter defined as the integral of U0 = λII squared f0 over z, corresponds to the full conversion of laser-imparted center of mass kinetic energy to radiation with θ ≥ θmin <ref:2607.10852#pg5>. The value of ν = νmax is an upper bound on ν since less than 100% efficiency of conversion into such radiation implies an even smaller ν <ref:2607. p. 1
Where the paper says it

2 kinetic energy K0 available to produce it for either ν = ν0 or ν = ν1, except for the lowest p. A much lower upper bound on ν = νmax, which assumes 100% conversion, results in a radiation pattern similar to published measurements2 taken with the same equipment and geometry, albeit with a laser pulse energy of 40 mJ instead of our 30 mJ.

10852#pg5>. The Q(z) measurement, which serves as the basis for Eq. 35, may be considered accurate for values of ν as low as νmax since it is an S-band diagnostic <ref:2607.10852#pg5>. The Q = If/ν1 using Eq. 21 and Eq. 24 being similar (within a factor of ∼ 2) to the self-emission measurement (Fig. 13) suggests that the mechanism has little effect on Q itself, such as a linear convolution like the one that results in Eθ (Eq. 34) <ref:2607.10852#pg5>. The contour plots of Fig. 6 provide a degree of corroboration <ref:2607.10852#pg5>. The following issues may account for the generally lower experimental Eθpp: K0 may be diverted to other processes, such as Ohmic heating and θ. The isolated primary filament assumption is not valid in many z locations, while K0 (as a collective property) assumes it is <ref:2607.10852#pg5>. The uniform cylinder approximation used to represent a Gaussian distribution to calibrate the Sband instrument is imprecise <ref:2607.10852#pg5>. The horns used to measure Eθ are dispersive with a frequency-dependent sensitivity, which alters the signal waveform, potentially lowering Eθpp <ref:2607.10852#pg5>. Reflection and refraction through the quartz tube has a ∼ 10% effect in terms of reducing the experimental Eθpp at θ = 15◦ <ref:2607.10852#pg5>. The comparison of Fig. 15 to Fig. E3a suggests that the former represents a baseline response of the far field to the wake field current that explicitly neglects the oscillatory modes recorded by the latter <ref:2607.10852#pg5>. The initial fast rise and fall to zero at θ = 15◦ for all p seen in Fig. E3a takes 33 ps, very similar to that seen in our Fig. 15 <ref:2607.10852#pg5>. The greater undershoot (aka “ring”) of the former and slow oscillation during subsequent decay not being present in our model may be attributed to our neglect of oscillatory current modes (such as those recorded by Zhou38 <ref:2607.10852#pg5>. The horn dispersion may also contribute to the oscillation <ref:2607.10852#pg5>.

Table 1 Data Summary

Table 1 shows that ν = νmax results in a reasonably good Eθpp match with Englebe’s data considering that νmax is only an upper bound <ref:2607.10852#pg5>. The Q = If/ν1 using Eq. 21 and Eq. 24 being similar (within a factor of ∼ 2) to the self-emission measurement (Fig. 13) suggests that the mechanism has little effect on Q itself, such as a linear convolution like the one that results in Eθ (Eq. 34) <ref:2607.10852#pg5>. The contour plots of Fig. 6 provide a degree of corroboration <ref:2607.10852#pg5>.

The simulation geometry is described in Figure A1, showing the portion of the quartz tube containing the filament external to the waveguide <ref:2607.10852#pg5>. The validation compares the theoretical values of A for several cases of actual uniform solid conducting filaments with measured values of R and σ of the same length as modeled <ref:2607.10852#pg5>. The self-emission simulation models the filament current at axial distance z from the waveguide center as I(z,t) = I0 t − z+0. p. 1

Where the paper says it

This self-emission signal is also used to measure Q. To calibrate it, a unipolar current pulse with a Gaussian time history with a short standard deviation (5 ps) relative to S-band is sent through the filament in the direction of the laser pulse in a time domain simulation of the waveguide geometry similar to that described above, but with no TE10 driver.

5H c cosπz/H for −H/2 ≤ z ≤ +H/2 and t ≥ 0 <ref:2607. p. 0
Where the paper says it

L , here, is the filament length and θ is emission angle. The total energy radiated due to the directly measured Q(z) far exceeds the laser-imparted center of mass electron arXiv:2607.

10852#pg5>. The conductivity is only turned on to G = 10-4 Sm at t = 1 ns, when the EM disturbance first reaches the receiver <ref:2607.10852#pg5>. The mesh, as illustrated in Fig. p. 8
Where the paper says it

4 ns, so this value is used for the integration limit. The subsequent simulated signal likely has contributions from the high frequency artifacts resulting from the filament axial mesh.

A7, has a maximum size of 2. p. 1
Where the paper says it

A Ti:sapphire USPL creates a linearly polarized 30 mJ optical pulse with a center wavelength of 800 nm. A single-shot second order autocorrelator measures the laser’s full width at half maximum (FWHM) pulse length to be 50 fs.

5 mm in these runs (1/6 times the vacuum wavelength of 20 GHz microwaves) to represent high order modes <ref:2607. p. 1
Where the paper says it

1, for a range of background air pressures p. Multiple reflections of the high frequency / high order modes above S-band (Fig.

10852#pg5>. The filament is shortened to 1/4 the length of the calibration simulation filaments, and the extensive PML is replaced with a much smaller Absorbing Boundary Condition (ABC) <ref:2607.10852#pg5>. The current is applied only to the filament surface due to code limitations; distributed beams are not supported <ref:2607. p. 9
Where the paper says it

Such a term contributes to oscillatory Sommerfeld wire surface modes34:6. 6 that have little effect on total charge transfer due to the monotonically decaying current of interest here.

10852#pg5>. The conductivity is distributed uniformly throughout the filament volume <ref:2607. p. 0
Where the paper says it

“Post-optical” here refers to time when the pulse has past, but the axial current has not had time to Ohmically decay to a significant degree. An analytic estimate ν1 of the subsequent current decay rate ν of a hypotheticalsteady state filament is found under the assumption that the current remains well-distributed throughout the cross section during decay.

10852#pg5>.

Table A1 Validation

Table A1 shows experimental measured attenuation parameter A results are compared to interpolated COMSOL continuous wave simulation results for a range of wire radii R and intrinsic conductivity σ <ref:2607.10852#pg5>. The tabulated values of σ for Cu and W are standard cited values <ref:2607. p. 1

Where the paper says it

A single-shot second order autocorrelator measures the laser’s full width at half maximum (FWHM) pulse length to be 50 fs. A 50 mm diameter beam is geometrically focused in air at various values of p by a 300 cm focal length spherical mirror.

p. 1
Where the paper says it

A single-shot second order autocorrelator measures the laser’s full width at half maximum (FWHM) pulse length to be 50 fs. A 50 mm diameter beam is geometrically focused in air at various values of p by a 300 cm focal length spherical mirror.

p. 1
Where the paper says it

A single-shot second order autocorrelator measures the laser’s full width at half maximum (FWHM) pulse length to be 50 fs. A 50 mm diameter beam is geometrically focused in air at various values of p by a 300 cm focal length spherical mirror.

10852#pg5>. The material R (mm) σ (S/m) G (Sm) A (exp. p. 4
Where the paper says it

The solid line tracks the peak intensity vs. z, with the dashed line above and below tracking the point at which intensity falls by a factor of exp(−1/2) on either side (one standard deviation s of a Gaussian profile).

p. 4
Where the paper says it

The solid line tracks the peak intensity vs. z, with the dashed line above and below tracking the point at which intensity falls by a factor of exp(−1/2) on either side (one standard deviation s of a Gaussian profile).

) A (theor.) is presented in Table A1 <ref:2607. p. 0
Where the paper says it

L , here, is the filament length and θ is emission angle. The total energy radiated due to the directly measured Q(z) far exceeds the laser-imparted center of mass electron arXiv:2607.

p. 0
Where the paper says it

L , here, is the filament length and θ is emission angle. The total energy radiated due to the directly measured Q(z) far exceeds the laser-imparted center of mass electron arXiv:2607.

10852#pg5>. The experimental measured attenuation parameter A results are compared to interpolated COMSOL continuous wave simulation results for a range of wire radii R and intrinsic conductivity σ <ref:2607.10852#pg5>. The tabulated values of σ for Cu and W are standard cited values <ref:2607.10852#pg5>. The material R (mm) σ (S/m) G (Sm) A (exp.) A (theor.) is presented in Table A1 <ref:2607.10852#pg5>. The experimental measured attenuation parameter A results are compared to interpolated COMSOL continuous wave simulation results for a range of wire radii R and intrinsic conductivity σ <ref:2607.10852#pg5>. The tabulated values of σ for Cu and W are standard cited values <ref:2607.10852#pg5>.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Precise Plasma Filament Property Inference: The improved AI can infer local plasma properties such as peak laser intensity I0, electron temperature T, and major species particle densities ni by inverting measurements of electrical conductivity sigma, characteristic radius R, and time integral Q using models like sigma = sigma (n1,n2,T).

  2. Accurate Microwave Radiation Modeling: The system can compare theoretical far field microwave radiation patterns due to axial current variation Q = Q(z) with published measurements and infer a much lower upper bound on the current decay rate nu once such radiation is taken into account.

  3. Self-Consistent Current Decay Rate Determination: The AI can estimate the hypothetical steady state filament's current decay rate nu by comparing two independent estimates, one based on near field energy and one based on filament self-emission, noting that The two estimates are in reasonable agreement despite the fact that nu, based on the following, is generally much lower.

  4. Conductivity Mapping from Diagnostic Data: The system can estimate peak free electron densities n1 and n2 as functions of I0 by solving the differential equation ni = ni0 / (1 - exp(-R + inf) - inf Wi(I(t))dt), allowing for detailed characterization of ionization rates Wi(I).

  5. Far Field Electric Field Prediction: The AI can calculate the far field electric field Etheta using the convolution integral Eq. 34, which incorporates the measured Q(z) and an approximated current waveform ξ (t), providing a prediction of radiated energy KR as a function of emission angle theta and decay rate nu.

  6. Pressure-Dependent Performance Benchmarking: The system can use Table 1 to compare far field E peak-peak amplitude Ethetapp across different background pressures p, identifying the optimal pressure for specific decay rates nu1, nu0, or the upper bound numax.

Abstract

The electrical conductivity σ of the plasma filament left behind by an ultrashort pulsed laser (USPL) optical pulse after it is geometrically then self-focused in air via the Kerr effect is measured by attenuation of a 3.2 GHz TE 10 mode within an S-band waveguide through which the filament passes, taking into account the characteristic radius R of the filament, as determined by fast camera visible light imaging. Models of the major air constituents' ionization rate W i vs. local laser intensity I, and of electron temperature T and mean axial electron momentum p z vs. peak laser intensity I 0 are then used to infer a hypothetical steady state filament's I 0, T, major species particle densities, and assumed axially invariant current time integral Q and current decay rate ν after pulse passage. Q is independently measured via the filament's self-emission signal in the waveguide for comparison. The theoretical far field microwave radiation pattern due to the actual axial variation in Q=Q (z) is compared favorably to published measurements. A much lower upper bound on ν is inferred once such radiation is taken into account. Results are presented along a 30 cm long filament at a broad range of atmospheric pressures.

Sources

Related papers