Stretching and bending of (really) thick elastic plates

arXiv:2606.01889 · cond-mat.soft · Submitted 2026-06-01 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.

Kai: We're looking at the paper: "Stretching and bending of (really) thick elastic plates".

Mira: Here's the gist of the paper. The paper addresses whether the separation of mechanical energy into stretching and bending components also emerges for really thick plates by computing effective moduli from small midline deformations The authors suggest that their calculations provide a justification for applying the thin-plate picture of stretching and bending to thick plates such as biological cell sheets.

Kai: The mechanical energy of an elastic plate separates into stretching and bending energies, which is a result for asymptotically thin plates, but it is often a surprisingly accurate approximation for thick plates too.

Mira: Slender elastic objects are described by effective theories that reduce their three-dimensional mechanics to one-dimensional midlines or two-dimensional midsurfaces.

Kai: For a thin plate of thickness h, the elastic energy E separates into stretching and bending energies as E proportional to h squared + h 4 K squared / 12, where E and K measure the stretching and bending of the midsurface, respectively.

Title and authors: Kai: So we're looking at this paper, "Stretching and bending of (really) thick elastic plates," and the authors are tackling something that's usually only thought about for thin plates.

Mira: Exactly. They are asking if we can separate the mechanical energy into stretching and bending components when the plate is actually really thick, not just asymptotically thin, which is where this paper starts.

Lev: It sounds like they want to see if that separation holds up when the thickness of the plate gets large enough to matter.

Kai: They do this by computing effective moduli from small midline deformations on these thicker plates. The core idea is testing if we can still use the thin-plate picture for things like biological cell sheets.

Mira: And what they find is that even when you look at deformations where the thickness h is of order one, they compute effective stretching and bending moduli, and their ratio stays about constant.

Lev: That sounds promising, because if that ratio doesn't change much, it means the stretching cost still dominates the bending cost even for thicker structures.

Kai: Right. They are trying to build a justification for applying thin-plate theory to these thicker things like cell sheets. The paper is titled "Stretching and bending of (really) thick elastic plates," which is just a bit long, isn't it?

Mira: It's descriptive, but the real point they make in the summary is that they compute the deformations of a thick elastic plate resulting from imposed, asymptotically small deformations of its midline to discover effective stretching and bending moduli.

Lev: So they are solving the full equations of elasticity for small deformations when you set h equal to one, which is a big step since thin plate theory usually assumes h is very small compared to other scales.

Kai: Yes, they do that by letting the thickness h be of order one and calculating effective stretching and bending moduli using equations like (17a) and (17b) <ref:2606.01889#pg3>. They use these effective quantities, E k and K, which are basically the leading-order terms in an energy density expansion.

Mira: And they show that the ratio of these two quantities, which they call the stretching number S, changes very little for deformations over lengthscales comparable to the plate's thickness. Specifically, they find that S minus one is about eta squared divided by thirty plus some higher order terms.

Lev: That means even when you move away from thin plate limits, the relative contribution of stretching versus bending stays pretty much the same as it was for a truly thin plate. That’s a strong result for modeling materials where both effects are present simultaneously.

Title and authors: Kai: So what does that mean for us? It suggests that the standard thin-plate picture isn't completely broken when applied to thick objects, especially in biology where cell sheets are often modeled as plates.

Mira: It gives us confidence in using those simplified stretching and bending energy terms because they seem to capture the physics well up to a certain scale. The paper is trying to bridge that gap between idealized thin models and real, thicker materials.

Lev: From an engineering standpoint, it means if we are designing simulations or models for thick materials, we can use this effective theory without having to solve the full three-dimensional elasticity equations every single time.

Kai: And they are also pointing out some improvements. One big suggestion is that this approach allows us to analyze material response in a regime where higher-order terms are negligible, based on the finding that for neo-Hookean materials, the stretching number I is about two plus some small epsilon squared terms.

Mira: That helps simplify the energy density calculation because we can rely on that leading-order approximation without getting bogged down in too many complexities early on.

Lev: And they also integrate geometric constraints into these plate mechanics models by using force-free boundary conditions on these surfaces derived from the asymptotic expansion, even when the Kirchhoff hypothesis breaks down due to shear deformations.

Kai: That’s a key point about the limitations. The paper admits that it's not solving for everything perfectly, and they mention that boundary effects arise from the additional boundary conditions on the lateral sides of the plate that we need in our finite-element simulations, which is something you have to account for if you want high accuracy.

Mira: So while it justifies the thin-plate picture up to a certain point, they are honest about where those specific mathematical simplifications still leave room for error or require further refinement.

Lev: It sounds like the path forward involves using these effective moduli and being careful with how we handle those boundary conditions in our actual simulations, which is where I spend most of my time building error-correction overhead for real hardware.

Kai: So to wrap up, the paper "Stretching and bending of (really) thick elastic plates" shows that even for thicker objects like biological cell sheets, the relative importance of stretching versus bending remains essentially unchanged when you look at deformations over scales comparable to the plate's thickness.

Mira: This provides a justification for applying the thin-plate picture in those scenarios, giving us a tool to describe these materials more effectively.

Lev: It’s a good piece of work because it connects the idealized thin model back to real physics at slightly larger scales, which is exactly what we need when moving from theory to building actual hardware or simulations.

The paper's summary: Kai: So, we're talking about this paper now, "Stretching and bending of (really) thick elastic plates," and it really boils down to whether that simple stretching and bending energy split still works for things that aren't just skin-deep thin sheets.

Mira: Exactly. The authors are doing calculations on small deformations of these thicker plates—where the thickness h is actually bigger than a tiny epsilon—to figure out if we can still use those simple stretching and bending terms to describe the material.

Kai: Right, they are computing effective moduli from midline deformations when the thickness is order one, which means they are looking at something much thicker than what standard thin-plate theory usually handles.

Mira: And what they find is that even for these thicker plates, when you look at how stretching and bending contribute to the energy, their ratio stays pretty constant over lengthscales that are about the same size as the plate's thickness.

Kai: That’s interesting because it means if you’re looking at something like a biological cell sheet or some other thick structure, you can still treat its energy using those leading-order stretching and bending terms without it being totally off.

Mira: It gives them justification for applying that thin-plate picture to these thicker plates, which is what they say. But they are also making a point about the limitations—they show that this approach works up to a certain scale, but you still need to be careful about those boundary conditions on the sides of the plate.

Kai: So it’s not a perfect solution for every single thickness or every single deformation, but it’s definitely a way to get good results without having to solve the full three-dimensional elasticity equations all the time.

Mira: It suggests that for modeling these things, we can simplify things by relying on these effective moduli because the stretching cost still dominates even when you move away from the purely thin limit.

Kai: It’s a nice bridge between idealized theory and what we actually see in thicker materials. So, if this works up to a certain scale, what does that mean for how we model these complex biological structures?

The paper's improvements: Kai: So, we're looking at the ways they suggest improving this work on thick plates, and it’s not just about confirming what they found but figuring out how to make the model more useful for real-world things.

Mira: Right, the authors mention that their method allows you to analyze material response in a regime where those higher-order terms are negligible, which is super helpful because it lets you stick to a simpler math without getting bogged down by too much complexity right away.

Kai: They point out that for materials like neo-Hookean ones, the stretching number, which is this ratio of stretching to bending energy, stays very close to two plus some small epsilon squared terms.

Mira: That means you can use a much simpler leading-order approximation for the elastic energy density when you’re dealing with those specific types of materials because they are governed by that relationship.

Kai: And they also talk about how this approach lets them incorporate geometric constraints into the plate mechanics models using these force-free boundary conditions that come from their asymptotic expansion, even when the Kirchhoff hypothesis breaks down because there is shear deformation.

Mira: That’s important because it shows you can keep using plate theory even in situations where those standard assumptions about how plates behave break apart due to things like shear.

Kai: So it’s not just a thick plate problem; it’s about adapting the mathematical framework so that it handles the actual physics of complex deformations better than a simple thin sheet model would.

Mira: It means we can use these effective moduli to build models for things that are thicker, and those models will be more accurate for describing how they actually behave under stress.

Kai: This moves us closer to being able to simulate thicker biological tissues or materials where both stretching and bending are happening at once without needing a massive computational overhead every single time we run a test.

Mira: So, the improvement is taking that leading-order result, making sure you use the right assumptions about the material—like that neo-Hookean one—and then using those boundary conditions to keep your model grounded in reality.

Kai: It really sets up a path for how we can start building more robust simulations for these complex systems. So, next up, we're going to look at some of the other papers we've got on the shelf today.

Conclusion: Kai: So we're wrapping up on "Stretching and bending of (really) thick elastic plates," and the main idea is that even for thicker structures, those effective stretching and bending terms still give us a good approximation.

Mira: Exactly. The paper shows that if you look at deformations where the thickness is order one, the ratio between stretching and bending moduli doesn't change much over scales related to the plate's thickness.

Kai: It means we can use this picture to model thick biological cell sheets without having to solve the full three-dimensional elasticity equations every time we run a simulation.

Lev: For me, that’s good because it reduces the computational overhead significantly when building error correction codes for real hardware; less complexity in the input means fewer gates needed in the circuit.

Mira: It gives us a way to simplify things by relying on that leading-order approximation because we know the stretching cost still dominates even when we go beyond purely thin plate assumptions.

Kai: So, if you're trying to design a model for something thick, this paper suggests using these effective moduli derived from small midline deformations as a solid starting point.

Lev: I just want to make sure that when we move to building actual hardware, we keep in mind those boundary conditions they mention; those lateral side effects are where the real numerical issues start popping up.

Mira: Right, so it’s a useful tool for simplifying the math, but you still need to be mindful of where the approximation stops holding true.

Kai: And that’s what we see—it's not a perfect answer for every single scenario, but it’s a strong justification for using these effective theories in practice.

Lev: I think that's the balance we need; a good starting point that saves time when you're trying to get results on actual systems.

Mira: So, the conclusion is that this work provides a mathematical path to apply thin-plate concepts to thicker plates by showing the stretching and bending contributions remain relatively stable.

Kai: That’s it for "Stretching and bending of (really) thick elastic plates," which really connects idealized theory back to what we see in thicker materials.

Lev: Next up, we're diving into the second law of thermodynamics in closed quantum many-body systems, which is a pretty big shift from classical elasticity.

Max Planck Institute for the Physics of Complex Systems · Max Planck Institute of Molecular Cell Biology and Genetics · Center for Systems Biology Dresden

cond-mat.soft

Submitted: 2026-06-01

Updated: 2026-06-01

Comments: 6 pages, 3 figures

Journal ref: Phys. Rev. E 114, L053501 (2026)

DOI: 10.1103/tpd1-t6d2

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 88/100

The gist: The paper addresses whether the separation of mechanical energy into stretching and bending components also emerges for really thick plates by computing effective moduli from small midline…

Key concepts

Stretching and Bending Energy Separation
The mechanical energy of an elastic plate naturally splits into two parts: stretching energy (related to in-plane deformation) and bending energy (related to out-of-plane curvature). This separation is a standard result for very thin plates, but the authors test if this separation holds true when the plate thickness is large.
Effective Moduli
These are calculated moduli that represent the combined stretching and bending behavior of a thick plate. By solving elasticity equations for small deformations, they derive these effective moduli, which allow them to apply thin-plate concepts to thicker structures.
Stretching Number (S)
The stretching number is a ratio (A/12B) quantifying the relative importance of stretching versus bending energy. The study finds that this ratio changes very little over length scales comparable to the plate's thickness, indicating that while stretching costs more energy, its relative contribution stays consistent with thin-plate models.

Terminology

Summary

The paper addresses whether the separation of mechanical energy into stretching and bending components also emerges for really thick plates by computing effective moduli from small midline deformations The authors suggest that their calculations provide a justification for applying the thin-plate picture of stretching and bending to thick plates such as biological cell sheets. p. 0

Where the paper says it

In this way, our calculations provide a justification for applying the thin-plate picture of stretching and bending to thick plates such as biological cell sheets. Slender elastic objects, such as rods, plates, or shells, are described by effective theories that reduce their threedimensional mechanics to one-dimensional midlines or two-dimensional midsurfaces [1–3].

Introduction to Plate Theories

The mechanical energy of an elastic plate separates into stretching and bending energies, which is a result for asymptotically thin plates, but it is often a surprisingly accurate approximation for thick plates too. Slender elastic objects are described by effective theories that reduce their three-dimensional mechanics to one-dimensional midlines or two-dimensional midsurfaces. p. 0

Where the paper says it

In this way, our calculations provide a justification for applying the thin-plate picture of stretching and bending to thick plates such as biological cell sheets. Slender elastic objects, such as rods, plates, or shells, are described by effective theories that reduce their threedimensional mechanics to one-dimensional midlines or two-dimensional midsurfaces [1–3].

For a thin plate of thickness h, the elastic energy E separates into stretching and bending energies as E proportional to h squared + h 4 K squared / 12, where E and K measure the stretching and bending of the midsurface, respectively. p. 0
Where the paper says it

Slender elastic objects, such as rods, plates, or shells, are described by effective theories that reduce their threedimensional mechanics to one-dimensional midlines or two-dimensional midsurfaces [1–3]. In particular, the elastic energy E of a thin plate of thickness h separates into stretching and bending energies, E ∝ h E 2 + h 2 12 K2 , (1) where E and K measure the stretching and bending of the midsurface, respectively, and the proportionality hides the material parameters.

This is the leading-order term in an expansion of the full, three-dimensional elastic energy for h = O(ε), with E = O(ε) and K = O(1) [Fig. p. 0
Where the paper says it

In particular, the elastic energy E of a thin plate of thickness h separates into stretching and bending energies, E ∝ h E 2 + h 2 12 K2 , (1) where E and K measure the stretching and bending of the midsurface, respectively, and the proportionality hides the material parameters. This is the leading-order term [3–6] in an expansion, in the small parameter ε ≪ 1, of the full, three-dimensional elastic energy of the plate for h = O(ε), with the midsurface scaling assumptions E = O(ε), K = O(1) [Fig.

1(a)].

Investigation of Thick Plate Deformations

The authors investigate this separation for a plate with h = O(1) by solving the equations of elasticity for small deformations, E = O(ε), K = O(ε) [Fig. 1(c)]. They compute effective stretching and bending moduli and show that their ratio remains approximately constant, providing a justification for applying the thin-plate picture to thick plates. p. 0

Where the paper says it

They soften with increasing plate thickness, but, strikingly, their ratio remains approximately constant. In this way, our calculations provide a justification for applying the thin-plate picture of stretching and bending to thick plates such as biological cell sheets.

The deformation gradient tensor F is defined based on the displacements parallel and perpendicular to the undeformed midsurface. p. 1
Where the paper says it

Let {ex, ez} be the Cartesian axes of the undeformed configuration. The deformation gradient tensor is defined to be F = ∂r˜/∂x ⊗ ex + ∂r˜/∂z ⊗ ez [26].

Asymptotic Solution Derivation

The authors solve the equations of mechanical equilibrium for imposed, small deformations of the midline by letting ˜f(x) = 1 + εE(x), ψ˜(x) = εΨ(x) for ε << 1. They introduce regular expansions for the displacements u˜ and w˜, and expand the incompressibility condition det F = 1 to obtain coupled equations [Eqs. p. 1

Where the paper says it

), we expand the incompressibility condition det F = 1 to obtain [29] ∂U(1) ∂x + ∂W(1) ∂z + E = 0, (10a) ∂U(2) ∂x + ∂W(2) ∂z − ∂U(1) ∂z Ψ + ∂W(1) ∂x + ∂W(1) ∂z E + ∂U(1) ∂x − Ψ2 2 = 0. (10b) Using these expansions, we find e = ε 2 2 " 4 ∂U(1) ∂x + E 2 + Ψ + ∂U(1) ∂z + ∂W(1) ∂x 2 # + O ε 3 .

(10a) and (10b)]. p. 1
Where the paper says it

), we expand the incompressibility condition det F = 1 to obtain [29] ∂U(1) ∂x + ∂W(1) ∂z + E = 0, (10a) ∂U(2) ∂x + ∂W(2) ∂z − ∂U(1) ∂z Ψ + ∂W(1) ∂x + ∂W(1) ∂z E + ∂U(1) ∂x − Ψ2 2 = 0. (10b) Using these expansions, we find e = ε 2 2 " 4 ∂U(1) ∂x + E 2 + Ψ + ∂U(1) ∂z + ∂W(1) ∂x 2 # + O ε 3 .

At leading order, the Cauchy equation simplifies to ∂2U(1)/∂x2 + ∂2U(1)/∂z2 + dE/dx - ∂p(1)/∂x = 0, and similar equations for W(1). p. 1
Where the paper says it

With this, using Eq. (10a), the Cauchy equation at next order simplifies to ∂ 2U(1) ∂x2 + ∂ 2U(1) ∂z2 + dE dx − ∂p(1) ∂x = 0, (14a) ∂ 2W(1) ∂x2 + ∂ 2W(1) ∂z2 + dΨ dx − ∂p(1) ∂z = 0.

Effective Moduli Analysis

The leading-order solution leads to a fourth-order inhomogeneous differential equation for the displacement component Wk(z) [Eq. (19)]. Substituting this result into the energy density expansion determines the effective stretching and bending moduli, Ek,l = Z h/2 - h/2 ek,l(z) dz. p. 0

Where the paper says it

This is a result for asymptotically thin plates, but it is often a surprisingly accurate approximation for thick plates, too. Here, we address this conundrum: We compute the deformations of a thick elastic plate resulting from imposed, asymptotically small deformations of its midline to discover effective stretching and bending moduli.

The prefactors A and B are thus effective stretching and bending moduli of the midline of the plate. p. 3
Where the paper says it

(26) separates into a stretching contribution and a bending contribution, proportional to h and h 3 , respectively. The prefactors A and B are thus effective stretching and bending moduli of the midline of the plate.

Conclusion on Relative Importance

The relative importance of stretching and bending is quantified by the stretching number S = A/12B, which is found to change very little for deformations over lengthscales comparable to the thickness of the plate, as S - 1 = η 2/30 + O η 4. This implies that the energetic cost of stretching swamps that of bending, but the relative contributions remain essentially unchanged from the case of a thin plate up to deformations over lengthscales comparable to the thickness. p. 3

Where the paper says it

3(b), inset], which results from the small prefactor in the leadingorder expansion S − 1 = η 2 30 + O η 4 . (29) Not only does the separation of stretching and bending thus arise for small deformations of a really thick plate, too, but also the relative importance of stretching and bending remains (essentially) unchanged from the case of a thin plate, up to deformations over lengthscales comparable to the thickness of the plate.

The paper concludes that thin-plate theories can capture the mechanical behaviour of these thick plates up to rescaling external forces. p. 3
Where the paper says it

Still, even for deformations over lengthscales comparable to the thickness of plate, the relative contributions of stretching and bending are almost the same for thin plates and for our thick plates. Thin-plate theories can therefore capture the mechanical behaviour of these thick plates, up to rescaling external forces to absorb the softening moduli.

References

[1] A. E. H. Love, A Treatise on the Mathematical Theory of Elasticity, 4th ed. p. 4

Where the paper says it

FEniCSx [30] code for the finite-element simulations is available openly at Ref. Love, A Treatise on the Mathematical Theory of Elasticity, 4th ed.

, Dover, New York, 1944 Chap. p. 4
Where the paper says it

Love, A Treatise on the Mathematical Theory of Elasticity, 4th ed. (Dover, New York, 1944) Chap.

XXII, pp. 455–464

[2] L. D. Landau and E. p. 4

Where the paper says it

(Dover, New York, 1944) Chap. Landau and E.

M. Lifshitz, Theory of Elasticity, 3rd ed. p. 4
Where the paper says it

Landau and E. Lifshitz, Theory of Elasticity, 3rd ed.

, Course of Theoretical Physics, Vol. p. 4
Where the paper says it

Lifshitz, Theory of Elasticity, 3rd ed. , Course of Theoretical Physics, Vol.

7 (Elsevier, Oxford, United Kingdom, 1986) Chap. p. 4
Where the paper says it

, Course of Theoretical Physics, Vol. 7 (Elsevier, Oxford, United Kingdom, 1986) Chap.

II, pp. 38–86

[3] B. Audoly and Y. p. 4

Where the paper says it

7 (Elsevier, Oxford, United Kingdom, 1986) Chap. Audoly and Y.

Pomeau, Elasticity and Geometry: From Hair Curls to the Non-linear Response of Shells (Oxford University Press, Oxford, 2008)

[4] P. G. Ciarlet, A justification of the von K´arm´an equations, Arch. p. 4

Where the paper says it

Pomeau, Elasticity and Geometry: From Hair Curls to the Non-linear Response of Shells (Oxford University Press, Oxford, 2008). Ciarlet, A justification of the von K´arm´an equations, Arch.

Ration. Mech. Anal., 73, 349 (1980)

[5] D. J. Steigmann, Koiter’s shell theory from the perspective of three-dimensional nonlinear elasticity, J. p. 4

Where the paper says it

73, 349 (1980). Steigmann, Koiter’s shell theory from the perspective of three-dimensional nonlinear elasticity, J.

Elast., 111, 91 (2013)

[6] J. Wang, Z. Song, and H. p. 4

Where the paper says it

111, 91 (2013). Song, and H.

-H. Dai, On a consistent finitestrain plate theory for incompressible hyperelastic materials, Int. p. 4
Where the paper says it

Song, and H. Dai, On a consistent finitestrain plate theory for incompressible hyperelastic materials, Int.

J. Solids Struct. p. 4
Where the paper says it

Dai, On a consistent finitestrain plate theory for incompressible hyperelastic materials, Int. Solids Struct.

p. 4
Where the paper says it

Dai, On a consistent finitestrain plate theory for incompressible hyperelastic materials, Int. Solids Struct.

, 78–79, 101 (2016)

[7] A. E. H. Love, XVI. The small free vibrations and deformation of a thin elastic shell, Phil. p. 4

Where the paper says it

78–79, 101 (2016). The small free vibrations and deformation of a thin elastic shell, Phil.

Trans. R. Soc. A, 179, 491 (1888)

[8] E. Reissner, The effect of transverse shear deformation on the bending of elastic plates, J. p. 4

Where the paper says it

A 179, 491 (1888). Reissner, The effect of transverse shear deformation on the bending of elastic plates, J.

Appl. Mech., 12, A69 (1945)

[9] R. D. Mindlin, Influence of rotatory inertia and shear on flexural motions of isotropic, elastic plates, J. p. 4

Where the paper says it

12, A69 (1945). Mindlin, Influence of rotatory inertia and shear on flexural motions of isotropic, elastic plates, J.

Appl. Mech., 18, 31 (1951)

[10] W. T. Koiter, On the nonlinear theory of thin elastic shells, Proc. p. 4

Where the paper says it

18, 31 (1951). Koiter, On the nonlinear theory of thin elastic shells, Proc.

K. Ned. Akad. Wet., B., 69, 1 (1966)

[11] D. D. Fox, A Raoult, and J C Simo, A justification of nonlinear properly invariant plate theories, Arch. p. 4

Where the paper says it

Raoult, and J. Simo, A justification of nonlinear properly invariant plate theories, Arch.

Ration. Mech. Anal., 124, 157 (1993)

[12] H. Le Dret and A Raoult, The membrane shell model in nonlinear elasticity: A variational asymptotic derivation, J. p. 4

Where the paper says it

Le Dret and A. Raoult, The membrane shell model in nonlinear elasticity: A variational asymptotic derivation, J.

Nonlinear Sci. p. 4
Where the paper says it

Raoult, The membrane shell model in nonlinear elasticity: A variational asymptotic derivation, J. Nonlinear Sci.

p. 4
Where the paper says it

Raoult, The membrane shell model in nonlinear elasticity: A variational asymptotic derivation, J. Nonlinear Sci.

, 6, 59 (1996)

[13] G. Friesecke, R. p. 4

Where the paper says it

6, 59 (1996). Friesecke, R.

D. James, and S M¨uller, A hierarchy of plate models derived from nonlinear elasticity by gammaconvergence, Arch. p. 4
Where the paper says it

James, and S. M¨uller, A hierarchy of plate models derived from nonlinear elasticity by gammaconvergence, Arch.

Ration. Mech. Anal., 180, 183 (2006)

[14] S Neukamm and I Velˇci´c, Derivation of a homogenized von K´arm´an plate theory from 3D nonlinear elasticity, Math. Models Methods Appl. p. 4

Where the paper says it

Velˇci´c, Derivation of a homogenized von K´arm´an plate theory from 3D nonlinear elasticity, Math. Models Methods Appl.

Sci., 23, 2701 (2013)

[15] J N Reddy, Theory and analysis of elastic plates and shells, 2nd ed., CRC Press, Boca Raton, FL, 2006 Chap. p. 4

Where the paper says it

Reddy, Theory and analysis of elastic plates and shells, 2nd ed. (CRC Press, Boca Raton, FL, 2006) Chap.

10, pp. 359–402

[16] H Hencky, Uber die Ber¨ucksichtigung der Schubverzer- ¨rung in ebenen Platten, Ing.-Arch., 16, 72 (1947)

[17] A Kromm, Uber die Randquerkr¨afte bei gest¨utzten Plat- ¨ten, Z. Angew. Math. Mech., 35, 231 (1955)

[18] W Wang and M X Shi, Thick plate theory based on general solutions of elasticity, Acta Mech., 123, 27 (1997)

[19] S S Antman, Nonlinear Problems of Elasticity, 1st ed., Springer, New York, NY, 1995 Chap. p. 4

Where the paper says it

Antman, Nonlinear Problems of Elasticity, 1st ed. (Springer, New York, NY, 1995) Chap.

VIII, pp. 259–324

[20] The equations of thick plates can also be solved in terms of infinite series: see, e.g., Refs., [21, 22]

[21] R Piltner, The application of a complex 3-dimensional elasticity solution representation for the analysis of a thick rectangular plate, Acta Mech., 75, 77 (1988)

[22] R Piltner, The derivation of a thick and thin plate formulation without ad hoc assumptions, J. Elast., 29, 133 (1992)

[23] A V Pogorelov, Bendings of surfaces and stability of shells, Translations of Mathematical Monographs, Vol. 72 (American Mathematical Society, Providence, RI, 1988) Chap. p. 4

Where the paper says it

Pogorelov, Bendings of surfaces and stability of shells, Translations of Mathematical Monographs, Vol. 72 (American Mathematical Society, Providence, RI, 1988) Chap.

1, pp. 1–16

[24] S Zhao and P A Haas, Mechanics of poking a cyst, Phys. Rev. Lett., 134, 228402 (20)

[54] Code is available at doi.org/10.5281/zenodo. p. 5

Where the paper says it

[54] Code is available at doi. 5281/zenodo.

p. 5
Where the paper says it

[54] Code is available at doi. 5281/zenodo.

20413363 (available openly at Ref. p. 4
Where the paper says it

Data availability A Mathematica notebook for the asymptotic calculations is provided in the Supplemental Material [29]. FEniCSx [30] code for the finite-element simulations is available openly at Ref.

p. 4
Where the paper says it

Data availability A Mathematica notebook for the asymptotic calculations is provided in the Supplemental Material [29]. FEniCSx [30] code for the finite-element simulations is available openly at Ref.

)

[55] Boundary effects arise from the additional boundary conditions on the lateral sides x = 0, x = 1 of the plate that we need in our finite-element simulations

[31] Boundary effects arise from the additional boundary conditions on the lateral sides x = 0, x = 1 of the plate that we need in our finite-element simulations

[32] A T Karttunen, R von Hertzen, J N Reddy, and J Romanoff, Bridging plate theories and elasticity solutions, Int. J. Solids Struct., 106–107, 251 (2017)

[33] H G Wood and J A Hanna, Contrasting bending energies from bulk elastic theories, Soft Matter, 15, 2411 (2019)

[34] O Ozenda and E G Virga, On the Kirchhoff–Love hypothesis (revised and vindicated), J. Elast., 143, 359 (2021)

[35] E Vitral and J A Hanna, Energies for elastic plates and shells from quadratic-stretch elasticity, J. Elast., 153, 581 (2022)

[36] J Dervaux, P Ciarletta, and M Ben Amar, Morphogenesis of thin hyperelastic plates: A constitutive theory of biological growth in the Föppl–von K´arm´an limit, J. Mech. Phys. Solids, 57, 458 (2009)

[37] J McMahon, A Goriely, and M Tabor, Nonlinear morphoelastic plates I: Genesis of residual stress, Math. Mech. Solids, 16, 812 (2011)

[38] D Moulton, T Lessinnes, and A Goriely, Morphoelastic rods. part I: A single growing elastic rod, J. p. 5

Where the paper says it

Goriely, Morphoelastic rods. part I: A single growing elastic rod, J.

Mech. Phys. Solids, 61, 398 (2013)

[39] S Sadik, A Angoshtari, A Goriely, and A Yavari, A geometric theory of nonlinear morphoelastic shells, J. Nonlinear Sci., 26, 929 (2016)

[40] D E Moulton, T Lessinnes, and A Goriely, Morphoelastic rods III: Differential growth and curvature generation in elastic filaments, J. Mech. Phys. Solids, 142, 104022 (2020)

[41] D Andrini, X Chen, and P Ciarletta, Nonlinear morphoelastic theory of biological shallow shells with initial stress, J. Elast., 157, 21 (2025)

[42] M Taffetani and M Pezzulla, Nonlinear morphoelastic energy based theory for stimuli responsive elastic shells, J. Elast., 158, 22 (2026)

[43] E Efrati, E Sharon, and R Kupferman, Elastic theory of unconstrained non-Euclidean plates, J. Mech. Phys. Solids, 57, 762 (2009)

[44] M Pezzulla, N Stoop, X Jiang, and D P Holmes, Curvature-driven morphing of non-Euclidean shells, Proc. R. Soc. A., 473, 20170087 (2017)

[45] L Giomi, Stretching theory of Hookean metashells, Phys. Rev. X, 16, 021035 (2026)

[46] S H¨ohn, A R Honerkamp-Smith, P A Haas, P Khuc Trong, and R E Goldstein, Dynamics of a Volvox embryo turning itself inside out, Phys. Rev. Lett., 114, 178101 (2015)

[47] P A Haas, S S M H H¨ohn, A R Honerkamp-Smith, J B Kirkegaard, and R E Goldstein, The noisy basis of morphogenesis: Mechanisms and mechanics of cell sheet folding inferred from developmental variability, PLoS Biol., 16, e2005536 (2018)

[48] P A Haas and R E Goldstein, Embryonic inversion in Volvox carteri: The flipping and peeling of elastic lips, Phys. Rev. E, 98, 052415 (2018)

[49] X Chen, X Yu, and P Ciarletta, A morphoelastic shell theory of biological invagination in embryos, J. Elast., 156, 1171 (2024)

[50] P A Haas and S S M H H¨ohn, Cut it out: Out-ofplane stresses in cell sheet folding of Volvox embryos, Phys. Rev. E, 111, 014420 (2025)

[51] V Tribet and P A Haas, A mechanical bifurcation constrains the evolution of cell sheet folding in the family Volvocaceae, arXiv:2603.15171 (available at Ref. p. 4

Where the paper says it

Data availability A Mathematica notebook for the asymptotic calculations is provided in the Supplemental Material [29]. FEniCSx [30] code for the finite-element simulations is available openly at Ref.

)

[52] S S Sheiko and A V Dobrynin, Architectural code for rubber elasticity: From supersoft to superfirm materials, Macromolecules, 52, 7531 (2019)

[53] L Lou, L Paolino, and A Agarwal, Bridging the gap in Ashby’s map for soft material properties for tissue engineering, ACS Appl. Mater. Interfaces, 15, 24197 (2023)

[54] Code is available at doi.org/10.5281/zenodo.20413363 (available openly at Ref.)

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Accurate prediction of mechanical behavior for thick biological cell sheets using effective theories derived from thin plate approximations, as our calculations provide a justification for applying the thin-plate picture of stretching and bending to thick plates such as biological cell sheets.

  2. Development of predictive models that incorporate the ratio of stretching to bending moduli, showing that their ratio remains approximately constant even as plate thickness increases.

  3. Ability to analyze material response in the regime where higher-order terms are negligible, based on the finding that I = 2 + O epsilon 2 for neo-Hookean materials, allowing for simplified leading-order approximations of elastic energy density.

  4. Simulation of complex deformation kinematics in thick plates by solving equations of elasticity for small deformations where h = O(1) to discover effective stretching and bending moduli.

  5. Integration of geometric constraints into plate mechanics models by using the force-free boundary conditions on these surfaces [7] derived from the asymptotic expansion, even when the Kirchhoff hypothesis breaks down due to shear deformations.

Abstract

The mechanical energy of an elastic plate separates into stretching and bending energies. This is a result for asymptotically thin plates, but it is often a surprisingly accurate approximation for thick plates, too. Here, we address this conundrum: We compute the deformations of a thick elastic plate resulting from imposed, asymptotically small deformations of its midline to discover effective stretching and bending moduli. They soften with increasing plate thickness, but, strikingly, their ratio remains approximately constant. In this way, our calculations provide a justification for applying the thin-plate picture of stretching and bending to thick plates such as biological cell sheets.

Sources

Related papers