Evaluation of External Magnetic Flux Density in Piezo-Flexomagnetic Nanobeams Using a Hybrid 1D-2D Finite Element Framework

arXiv:2605.19422 · cond-mat.mtrl-sci, cs.NA, math.NA · Submitted 2026-05-19 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.

Kai: We're looking at the paper: "Evaluation of External Magnetic Flux Density in Piezo-Flexomagnetic Nanobeams Using a Hybrid 1D-2D Finite Element Framework".

Mira: Here's the gist of the paper. This study numerically evaluates the external magnetic flux density generated in air by bending a piezo-flexomagnetic nanobeam using a hybrid 1D-2D finite element framework The proposed framework employs a coupled hybrid finite element formulation combining a 1D Timoshenko beam model with a 2D magnetostatic problem encompassing both the beam body and the surrounding air domain The results demonstrate the presence of a significant external magnetic flux distribution in free-standing structures, even in the absence of piezomagnetic coupling A systematic sensitivity analysis further identifies the material parameters most strongly influencing the external transverse magnetic flux density These findings provide insight into the design of nanoscale non-contact magnetoelastic sensing systems.

Kai: Pruning redundant reasoning tokens The motivation for this research is to determine the external non-negligible magnetic quantities generated by bending a piezo-flexomagnetic nanobeam.

Mira: The core idea is that when the nanobeam generates a magnetic field in response to mechanical stimulus, it can be detected by a magnetometer.

Kai: This principle has been utilized in non-contact torque sensors and muscle activity sensors among others A piezo-flexomagnetic beam model combines the effect of both piezomagnetism and flexomagnetism.

Title and authors: Kai: So we're looking at this paper titled "Evaluation of External Magnetic Flux Density in Piezo-Flexomagnetic Nanobeams Using a Hybrid 1D-2D Finite Element Framework," and the authors are Lala Samprit Ray and Bishweshwar Babu, who are tackling how bending a specific nanobeam creates a magnetic field outside of it even when we ignore the direct coupling between strain and magnetism <ref:2605.19422#pg1,Evaluation of External Magnetic Flux Density in Piezo-Flexomagnetic Nanobeams Using a>.

Mira: It sounds like they're proposing this coupled one dimensional two dimensional finite element framework that mixes a simple one dimensional beam model with a two dimensional magnetostatic problem that covers both the beam itself and the air around it.

Lev: It's interesting they mentioned checking their work against analytical solutions for magnetically isolated beams, which is crucial because we need to know if their simulation method actually reproduces known physics.

Kai: What's important is that the results show a significant external magnetic flux distribution in free-standing structures, even when there isn't any direct piezomagnetic coupling happening at all. That means bending generates this field on its own, independent of that direct strain to magnetic link.

Mira: So they are confirming that flexomagnetism alone is capable of generating these external fields, which is different from what we thought when we only looked at the response happening inside the structure.

Lev: I wonder how much computational overhead this one dimensional to two dimensional coupling adds when you actually try to run this on real hardware, Kai?

Kai: That’s a good point, Lev. The methodology involves a bidirectional approach where they project the magnetic field back onto the one dimensional axis after solving the two dimensional problem. They use an iterative staggered fixed point scheme for this, which is how they manage decoupling those continuous formulations into sequential problems.

Mira: And what’s interesting from analyzing magnetic quantities is that they found a clear source region at the bottom of a flexomagnetic beam and a sink region at its top because of that constant strain gradient across the thickness. They point out that only the term coupled to Bz via strain gradient eta xxz, f thirty-one is dominant in their specific plot <ref:2605.19422#pg2>.

Title and authors: Lev: That's a concrete finding about where the magnetic action happens inside the structure. Does that localization change how we approach error correction when you try to run this on real hardware?

Kai: The paper points out that their framework replaces the simplifying assumption that we ignore the external magnetic domain with actual magnetic interface conditions. This is a big methodological improvement because it moves us away from just assuming isolation.

Mira: The main implication is that we can now design non-contact magnetoelastic sensing systems because this framework quantifies that external transverse magnetic flux density Bz. It shows that the bending itself generates a signal even without direct piezomagnetic coupling.

Lev: I just want to add that the method they used, involving Magnetic Load Projection and Kinematic Field Mapping in their iterative scheme, is quite specific. Running this on real hardware would mean managing the convergence criteria you mentioned for the error falling below ten to the minus nine between iterations <ref:2605.19422#pg2>.

Kai: That’s right, Lev. And I also think their sensitivity analysis showing that d fifteen dominates over d thirty-one is a really useful piece of information for anyone designing nanoscale devices <ref:2605.19422#pg2>. It gives us a clear direction on which mechanical effects we need to focus on when we're trying to get a strong external magnetic signal.

Mira: Exactly. So the paper "Evaluation of External Magnetic Flux Density in Piezo-Flexomagnetic Nanobeams Using a Hybrid 1D-2D Finite Element Framework" gives us a solid numerical tool for understanding how mechanical deformation translates into measurable external fields in these advanced materials <ref:2605.19422#pg1,Evaluation of External Magnetic Flux Density in Piezo-Flexomagnetic Nanobeams Using a>.

Lev: It’s a solid piece of work that bridges the gap between theory and what might actually be built, even if the complexity of that one dimensional to two dimensional coupling is high for practical implementation.

Kai: So we've looked at how bending a piezo-flexomagnetic nanobeam creates an external magnetic field using this coupled one dimensional two dimensional finite element framework.

Mira: Yeah, and the main thing is that even without piezomagnetism you get a significant magnetic flux distribution just from the bending itself. That's a pretty big thing for understanding these structures.

Title and authors: Lev: From an error correction standpoint, it means we're dealing with these complex continuous formulations that need careful handling in any real hardware implementation, right?

Kai: Right, Lev. The methodology involves this iterative staggered fixed point scheme where they project the magnetic field back onto the one dimensional axis after solving the two dimensional problem.

Mira: And what's really interesting from analyzing magnetic quantities is that they found a clear source region at the bottom and a sink region at the top because of that constant strain gradient across the beam thickness. It shows how strain gradients create localized fields.

Lev: That's what I need to run on real hardware—we gotta make sure that spatial discretization is fine enough to capture those sharp regions, otherwise you get numerical noise overwhelming the actual physical effect.

Kai: And then they do a sensitivity analysis on the external transverse magnetic flux density Bz and found that the permeability of the air domain is actually the most dominant material parameter.

Mira: That tells us that in designing these sensors, we can't just focus on the beam itself; we have to worry about what's around it, like the surrounding air.

Lev: So if you want a high signal, you might need to engineer your environment for high air permeability, which adds another layer of complexity to the whole system design.

Kai: It’s interesting because they also showed good agreement with analytical results when they suppressed the air domain by assuming a very small magnetic permeability of air. That validates their model against simpler cases.

Mira: So, to wrap up, this paper "Evaluation of External Magnetic Flux Density in Piezo-Flexomagnetic Nanobeams Using a Hybrid 1D-2D Finite Element Framework" gives us a solid numerical tool for understanding how bending creates external magnetic fields <ref:2605.19422#pg1,Evaluation of External Magnetic Flux Density in Piezo-Flexomagnetic Nanobeams Using a>.

Lev: It's a good step toward modeling these systems, but the coupling itself is heavy, so it shows where the real computational overhead lands when you try to translate this into something you can actually build.

The paper's summary: Kai: So, to recap, this paper is using a coupled one dimensional two dimensional finite element framework to look at how bending a piezo flexomagnetic nanobeam creates an external magnetic field outside of it.

Mira: That’s right, and the big takeaway is that you get a significant magnetic flux distribution just from the bending itself, even when you aren't directly coupling strain and magnetism.

Lev: It really moves us away from just looking at what happens inside the material to understanding what happens outside of it.

Kai: Exactly. The framework uses this two dimensional magnetostatic problem combined with a one dimensional beam model, which is a pretty advanced way to handle the geometry of these things.

Mira: And they checked their model against analytical solutions for beams that are completely magnetically isolated, which is important because it lets them know if their simulation method actually matches what we already know about physics.

Lev: It’s good they did that, because when you're building hardware, you need to trust the foundation before you start adding the complex coupling terms in there.

Kai: Right. Now look at how they handled the math for this coupling—it’s a bidirectional approach where they project fields back and forth between the one dimensional beam axis and that two dimensional magnetic domain.

Mira: And what’s really interesting is how they mapped those quantities, showing a distinct source region at the bottom of a flexomagnetic beam and a sink region at the top because of that constant strain gradient across the thickness.

Lev: That localization is key. It tells us exactly where to look if we want to design something that detects this signal without noise overwhelming the actual physical effect when we put it on hardware.

Kai: They also did a sensitivity analysis on the external magnetic flux density and found that the permeability of the air domain is actually the most dominant material parameter influencing how strong that field gets.

Mira: That means if you’re designing these sensors, you can't just focus on tuning the beam itself; you have to worry about what’s surrounding it, like the air right next to it.

Lev: So if you want a high signal, maybe your design needs to account for engineering an environment with high air permeability. That adds another layer of complexity we have to deal with when we think about building something that actually works on a chip or in a sensor array.

Kai: And they did confirm their approach is solid because they got good agreement with analytical results when they reduced the magnetic permeability of the air to something very small, like ten to the power negative twenty newtons per ampere squared.

Mira: So, basically, this paper gives us a numerical tool that shows bending creates external magnetic fields in piezo flexomagnetic materials without needing that direct piezomagnetic coupling you used to assume was necessary.

Lev: It’s a solid numerical tool for understanding the physics, but the coupling itself is heavy, so it shows where the real computational overhead lands when you try to translate this into something you can actually build.

Kai: Exactly. So what we need to figure out next is how we can manage that iterative process on actual hardware without losing fidelity.

The paper's improvements: Kai: So, to recap, this paper is using a coupled one dimensional two dimensional finite element framework to look at how bending a piezo flexomagnetic nanobeam creates an external magnetic field outside of it.

Mira: That’s right, and the big takeaway is that you get a significant magnetic flux distribution just from the bending itself, even when you aren't directly coupling strain and magnetism.

Lev: It really moves us away from just looking at what happens inside the material to understanding what happens outside of it.

Kai: What they suggest for improvement is replacing that old assumption—the one where we pretend there's no external magnetic domain—with actual magnetic interface conditions.

Mira: That’s a big methodological change because it stops us from just assuming everything is isolated, which was a major simplification in older models.

Lev: If we can model the real boundary conditions instead of ignoring them, that gives us a more realistic picture for anything we try to build with these materials.

Kai: The paper shows how this new framework lets them quantify that external transverse magnetic flux density, which is the Bz quantity you want to measure.

Mira: So it opens up the door to designing non-contact magnetoelastic sensing systems because now they have a mathematical way to calculate exactly what signal you’d get from a bending structure.

Lev: That's actually huge for hardware design because it means we can start predicting the output without having to rely on overly simplified assumptions about the magnetic environment.

Kai: They also found that their sensitivity analysis, where they checked how much different material parameters affect that magnetic field, points to a specific direction for us.

Mira: Specifically, they found that shear effects contribute more to the external flux density via a parameter called d one five than bending effects do via d three one.

Lev: That's actionable information because it tells us exactly which mechanical influences we need to focus on if we want to get a strong signal out of the system.

Kai: So, in short, this work gives us a solid numerical tool for understanding how mechanical deformation translates into measurable external fields in these advanced materials.

Mira: It’s a solid tool, yes, but the real test is whether it can accurately predict what happens when we move from theory to something that actually runs on real hardware.

Lev: That's exactly where the challenge lies; bridging that gap between the complex one dimensional two dimensional coupling and actual physical implementation is still a big hurdle.

Conclusion: Kai: So we've looked at how bending a piezo flexomagnetic nanobeam creates an external magnetic field using this coupled one dimensional two dimensional finite element framework.

Mira: Yeah, and the main thing is that even without piezomagnetism you get a significant magnetic flux distribution just from the bending itself.

Lev: From an error correction standpoint, it means we're dealing with these complex continuous formulations that need careful handling in any real hardware implementation, right?

Kai: Right, Lev. The methodology involves this iterative staggered fixed-point scheme where they project the magnetic field back onto the one dimensional axis after solving the two dimensional problem.

Mira: And what's really interesting from the analysis of magnetic quantities is that they found a clear source region at the bottom and a sink region at the top because of that constant strain gradient across the beam thickness.

Lev: That's what I need to run on real hardware—we gotta make sure that spatial discretization is fine enough to capture those sharp regions, otherwise you get numerical noise overwhelming the actual physical effect.

Kai: And then they do a sensitivity analysis on the external transverse magnetic flux density and found that the permeability of the air domain is actually the most dominant material parameter.

Mira: That tells us that in designing these sensors, we can't just focus on the beam itself; you have to worry about what's around it, like the surrounding air.

Lev: So if you want a high signal, you might need to engineer your environment for high air permeability, which adds another layer of complexity to the whole system design.

Kai: It’s interesting because they also showed good agreement with analytical results when they suppressed the air domain by assuming a very small magnetic permeability of air. That validates their model against simpler cases.

Mira: So, to wrap up, this paper "Evaluation of External Magnetic Flux Density in Piezo-Flexomagnetic Nanobeams Using a Hybrid 1D-2D Finite Element Framework" gives us a solid numerical tool for understanding how bending creates external magnetic fields <ref:2605.19422#pg1,Evaluation of External Magnetic Flux Density in Piezo-Flexomagnetic Nanobeams Using a>.

Lev: It's a good step toward modeling these systems, but the coupling itself is heavy, so it shows where the real computational overhead lands when you try to translate this into something you can actually build.

Kai: We need to keep an eye on how they handle that iterative staggering in their staggered fixed-point scheme because that's where the actual computation happens.

Mira: I agree, and it’s important we remember that the result is heavily dependent on those assumptions about the magnetic interface conditions they introduced.

Lev: Definitely, and for anyone looking at hardware applications, understanding those convergence criteria you mentioned is going to be a major part of their work when they try to implement this in a real system.

Department of Mechanical Engineering, National Institute of Technology Tiruchirappalli

cond-mat.mtrl-sci, cs.NA, math.NA

Submitted: 2026-05-19

Updated: 2026-11-11

Comments: Accepted author manuscript. Published in Eur. J. Mech. A Solids. 31 pages, 12 figures, 3 tables

Journal ref: European Journal of Mechanics - A/Solids (2026), 106422

DOI: 10.1016/j.euromechsol.2026.106422

License: http://creativecommons.org/licenses/by-nc-nd/4.0/

Importance score: 70/100

The gist: This study numerically evaluates the external magnetic flux density generated in air by bending a piezo-flexomagnetic nanobeam using a hybrid 1D-2D finite element framework The proposed framework…

Key concepts

Piezo-Flexomagnetic Nanobeam
A nanobeam that exhibits both piezomagnetism and flexomagnetism. Piezomagnetism links mechanical strain to magnetic polarization, while flexomagnetism relates strain gradients to magnetic effects. This combination allows the beam's bending to generate a measurable external magnetic field.
Coupled 1D-2D Framework
A numerical modeling approach that treats the nanobeam as a 1D structure (for mechanical behavior) coupled with a 2D domain (for magnetic fields). This framework uses specific coupling strategies to link the beam's deformation directly to the resulting magnetic field distribution in the surrounding air.
External Transverse Magnetic Flux Density (Bz)
The measure of the magnetic field component perpendicular to both the beam's axis and its cross-section. This quantity is what is generated externally by bending and is crucial for detecting these nanoscale structures using non-contact sensing methods like magnetometers.
Sensitivity Analysis
A mathematical process used to determine how much a specific output, like Bz, changes when an input material parameter (e.g., air permeability) is varied. This analysis reveals which material properties have the strongest influence on the final magnetic signal.

Terminology

Summary

This study numerically evaluates the external magnetic flux density generated in air by bending a piezo-flexomagnetic nanobeam using a hybrid 1D-2D finite element framework The proposed framework employs a coupled hybrid finite element formulation combining a 1D Timoshenko beam model with a 2D magnetostatic problem encompassing both the beam body and the surrounding air domain The results demonstrate the presence of a significant external magnetic flux distribution in free-standing structures, even in the absence of piezomagnetic coupling A systematic sensitivity analysis further identifies the material parameters most strongly influencing the external transverse magnetic flux density These findings provide insight into the design of nanoscale non-contact magnetoelastic sensing systems. p. 0

Where the paper says it

The results demonstrate the presence of a significant external magnetic flux distribution in free-standing structures, even in the absence of piezomagnetic coupling. A systematic sensitivity analysis further identifies the material parameters most strongly influencing the external transverse magnetic flux density.

Pruning redundant reasoning tokens

The motivation for this research is to determine the external non-negligible magnetic quantities generated by bending a piezo-flexomagnetic nanobeam. The core idea is that when the nanobeam generates a magnetic field in response to mechanical stimulus, it can be detected by a magnetometer. p. 0

Where the paper says it

1 Introduction The motivation of the current study is to determine the external non-negligible magnetic quantities generated by the bending of a piezo-flexomagnetic nanobeam. The idea is that when the nanobeam generates a magnetic field in response to a mechanical stimulus, it will be detected by a magnetometer.

This principle has been utilized in non-contact torque sensors and muscle activity sensors among others A piezo-flexomagnetic beam model combines the effect of both piezomagnetism and flexomagnetism. p. 0
Where the paper says it

This principle has been utilized in non-contact torque sensors [1, 2] and muscle activity sensors [3] among others [4]. Such applications exploit the magnetostrictive effect due to its accessibility without symmetry constraints.

Piezomagnetism describes a linear coupling between uniform mechanical strain and magnetic polarization, whereas flexomagnetism describes a strain gradient-driven effect. p. 0
Where the paper says it

A piezo-flexomagnetic beam model, as the name suggests, combines the effect of both piezomagnetism and flexomagnetism. Piezomagnetism describes a linear coupling between uniform mechanical strain and magnetic polarization whereas flexomagnetism describes a strain gradient-driven effect.

The inclusion of the flexomagnetic model may guide the design of new non-contact nanoscale devices because strain gradients scale inversely with structural size, making the flexomagnetic effect pronounced in nanostructures. p. 0
Where the paper says it

Because strain gradients scale inversely with structural size, the flexomagnetic effect becomes pronounced in nanostructures [7–10]. Therefore, inclusion of the flexomagnetic model may guide the design of new non-contact nanoscale devices.

How the training signal is built

The numerical evaluation utilizes a coupled 1D-2D framework where a 1D beam neutral axis is coupled with a 2D domain encompassing both the beam body and the surrounding ambient air The governing equations for the beam are derived using the principle of virtual work, leading to governing differential equations (GDEs) in terms of resultants. These GDEs include equations such as ∂Nxx/∂x = 0, ∂Qxz/∂x − q(x) = 0, and ∂Mxx/∂x − Qxz + ∂Txxz/∂x = 0 for the 1D domain. p. 3

Where the paper says it

Utilizing Equations (6) and (7) in Equation (5), the GDEs in terms of the resultants are obtained for the 1D domain x ∈ [0, L] as, ∂Nxx ∂x = 0, (8a) ∂Qxz ∂x − q(x) = 0, (8b) ∂Mxx ∂x − Qxz + ∂Txxz ∂x = 0, (8c) and in the 2D beam domain x ∈ [0, L], z ∈ [−h/2, h/2], assuming no y-dependence, as: ∂Bx ∂x + ∂Bz ∂z = 0. (8d) The boundary conditions at end points x = 0, L are either, u = ¯u or Nxx = N¯ xx, (9a) w = ¯w or Qxz = Q¯ xz, (9b) ϕ = ϕ¯ or Mxx + Txxz = M¯ xx.

In the 2D beam domain, the equation is∂Bx/∂x + ∂Bz/∂z = 0. p. 3
Where the paper says it

Utilizing Equations (6) and (7) in Equation (5), the GDEs in terms of the resultants are obtained for the 1D domain x ∈ [0, L] as, ∂Nxx ∂x = 0, (8a) ∂Qxz ∂x − q(x) = 0, (8b) ∂Mxx ∂x − Qxz + ∂Txxz ∂x = 0, (8c) and in the 2D beam domain x ∈ [0, L], z ∈ [−h/2, h/2], assuming no y-dependence, as: ∂Bx ∂x + ∂Bz ∂z = 0. (8d) The boundary conditions at end points x = 0, L are either, u = ¯u or Nxx = N¯ xx, (9a) w = ¯w or Qxz = Q¯ xz, (9b) ϕ = ϕ¯ or Mxx + Txxz = M¯ xx.

Where the gains come from

The coupling strategy involves a bidirectional approach where forward coupling relates mechanical displacements to strain fields in the beam body, which act as source terms in the 2D magnetic governing equations via coupling coefficients. Reverse coupling projects the resulting 2D magnetic field back onto the 1D structural axis by integrating the 2D magnetic potential over the beam thickness. p. 5

Where the paper says it

Consequently, the mechanical response directly drives the generation of the 2D scalar magnetic potential, ψ(x, z), throughout the beam body and the surrounding air domain. Reverse coupling (2D to 1D) The reverse coupling mechanism projects the resulting 2D magnetic field back onto the 1D structural axis.

The iterative solution algorithm employs a staggered fixed-point iteration scheme, decoupling continuous formulations into sequential boundary-value problems. p. 6
Where the paper says it

Instead, the proposed framework employs a staggered fixed-point iteration scheme, decoupling the continuous formulations in Section 2. 5 into sequential boundary-value problems.

This process involves Magnetic Load Projection (2D to 1D), Structural Subproblem Update (1D), and Kinematic Field Mapping (1D to 2D) in each iteration. p. 7
Where the paper says it

Structural Subproblem Update: Utilizing these static magnetic loads, the 1D mechanical weak form, Equation (16a), is solved to determine the current kinematic variables (u i , wi , ϕi ). Kinematic Field Mapping (1D to 2D): The newly computed 1D mechanical displacements (u i , wi , ϕi ) are mapped from the neutral axis throughout the 2D beam body.

Analysis of Magnetic Quantities

The analysis compares the magnetic potential, magnetic field vector, and magnetic flux density vector for both piezo-flexomagnetic and only flexomagnetic materials under a uniformly distributed load. The surface plots show the continuity of the magnetic scalar potential across beam boundaries facilitated by conforming node sharing at the beam-air interface. p. 7

Where the paper says it

Figure 4 presents this behavior in transversely loaded piezo-flexomagnetic and flexomagnetic beams. The surface plots in Figures 4a and 4d show the continuity of magnetic scalar potential (ψ) across the beam boundaries facilitated by conforming node sharing at the beam-air interface.

Figure 4f reveals a clear source region at the bottom of a flexomagnetic beam and a sink region formed at its top due to a constant strain gradient across the thickness of the beam. p. 8
Where the paper says it

This pattern reflects the tendency of magnetic flux to remain concentrated within the higher-permeability beam region. The most interesting plot is the pattern of vector plot shown in Figure 4f which shows a clear source region at the bottom of a flexomagnetic beam and a sink region formed at its top due to a constant strain gradient across the thickness of the beam.

The most interesting plot is shown in Figure 7b, which indicates that only the term coupled to Bz via strain gradient ηxxz, f31 as seen in Equations (3e) and (11d), is dominant in Figure 7b because no other magneto-mechanical coupling term from Equations (3d) and (3e) is active. p. 8
Where the paper says it

The most interesting plot is the pattern of vector plot shown in Figure 4f which shows a clear source region at the bottom of a flexomagnetic beam and a sink region formed at its top due to a constant strain gradient across the thickness of the beam. This result is significant because it is a numerical analysis of a non-negligible magnetic quantity in air due to a bending flexomagnetic structure.

Sensitivity Analysis

The sensitivity analysis focuses on the external transverse magnetic flux density Bz to material parameter variations using a normalized sensitivity index S. The analysis reveals the dominating effect of the permeability of air domain in Figure 7 signifying that a highly permeable external material would result in a higher Bz. p. 8

Where the paper says it

1h from the bottom surface (y = −h/2 − 0. The sensitivity analysis reveals the dominating effect of the permeability of air domain in Figure 7 signifying that a highly permeable external material would result in a higher Bz.

Furthermore, the dominance of d15 over d31 in Figure 7a reveals that shear effects contribute more to the external flux density via d15 than bending effects via d31. p. 8
Where the paper says it

The sensitivity analysis reveals the dominating effect of the permeability of air domain in Figure 7 signifying that a highly permeable external material would result in a higher Bz. The dominance of d15 over d31 in Figure 7a reveals that shear effects contribute more to the external flux density via d15 than bending effects via d31.

This is because when the neutral axis is in the middle of a bending piezo-flexomagnetic beam, the magnetic flux density field at the top half gets balanced with those at the bottom (Figure 4c). p. 8
Where the paper says it

The dominance of d15 over d31 in Figure 7a reveals that shear effects contribute more to the external flux density via d15 than bending effects via d31. This is because when the neutral axis is in the middle of a bending piezo-flexomagnetic beam, the magnetic flux density field at the top half gets balanced with those at the bottom (Figure 4c).

The sensitivity analysis quantifies this dependence using Equation (18), where S = (Bz − Bz,0)/Bz,0 / (X − X0)/X0. p. 8
Where the paper says it

Figure 5, also reveals the continuity of the scalar magnetic potential ψ(x, z) due to node sharing at the x and z beam-interfaces but with a kink at the interface which is also where its highest magnitude is located. 3 Sensitivity Analysis The main limitation of a numerical approach is that the dependence of a computed quantity on the model parameters is not immediately apparent.

Conclusion

This study presented a hybrid 1D-2D finite element framework to evaluate the external magnetic signatures of piezo-fexomagnetic beams. By coupling a 1D Timoshenko beam model with a 2D cross-sectional magnetic domain, the framework replaces the simplifying magnetic isolation assumption prevalent in current piezoflexomagnetic beam literature with magnetic interface conditions. p. 5

Where the paper says it

Based on the kinematics of Timoshenko beam theory, from Equation (1), the axial displacement u(x), transverse displacement w(x), and cross-sectional rotation ϕ(x) dictate the 2D strains and strain gradients, in Equation (2) at any point (x, z) within the beam thickness. These induced strains and strain gradients act as source terms in the 2D magnetic governing equations via the coupling coefficients d31, d15 and f31.

p. 5
Where the paper says it

Based on the kinematics of Timoshenko beam theory, from Equation (1), the axial displacement u(x), transverse displacement w(x), and cross-sectional rotation ϕ(x) dictate the 2D strains and strain gradients, in Equation (2) at any point (x, z) within the beam thickness. These induced strains and strain gradients act as source terms in the 2D magnetic governing equations via the coupling coefficients d31, d15 and f31.

The framework is validated against established analytical beam problems for magnetically isolated cases by reducing the magnetic permeability of air. p. 1
Where the paper says it

By enforcing the continuity of the magnetic scalar potential across the beam-air interface and imposing far-field Dirichlet conditions, we have enabled the evaluation of external magnetic field intensity (H) and flux density (B) using standard magnetostatic relations. This model is validated against analytical results of magnetically isolated piezo-flexomagnetic nanobeam.

p. 1
Where the paper says it

By enforcing the continuity of the magnetic scalar potential across the beam-air interface and imposing far-field Dirichlet conditions, we have enabled the evaluation of external magnetic field intensity (H) and flux density (B) using standard magnetostatic relations. This model is validated against analytical results of magnetically isolated piezo-flexomagnetic nanobeam.

Sensitivity analysis revealed the dominant material parameters affecting a transduced magnetic quantity in a bending flexomagnetic or piezo-flexomagnetic beam. p. 1
Where the paper says it

This model is validated against analytical results of magnetically isolated piezo-flexomagnetic nanobeam. Finally, a sensitivity analysis reveals the material parameters most responsible for an external signal within the present configuration.

p. 1
Where the paper says it

This model is validated against analytical results of magnetically isolated piezo-flexomagnetic nanobeam. Finally, a sensitivity analysis reveals the material parameters most responsible for an external signal within the present configuration.

References

[1] R. Andreescu, B. Spellman, and E.P. Furlani

[2] I.J. Garshelis and C.R. Conto

[3] E Pina, E Burgos, C Prados, J. M González, A Hernando, M. C Iglesias, J Poch, and C Franco

[4] Frederick T. Calkins, Alison B. Flatau, and Marcelo J. Dapino

[5] E A Eliseev

[6] A F Kabychenkov and F V Lisovskii

[7] Boris A Belyaev, Andrey V Izotov, Platon N Solovev, and Nikita M Boev

[8] Dongxue Du, Sebastian Manzo, Chenyu Zhang, Vivek Saraswat, Konrad T Genser, Karin M Rabe, Paul M Voyles, Michael S Arnold, and Jason K Kawasaki

[9] Ziming Tang, Qihua Gong, and Min Yi

[10] Qihua Gong, Ziming Tang, and Min Yi

[11] Sai Sidhardh and M C Ray

[12] Jan Sladek, Vladimir Sladek, Mengkang Xu, and Qian Deng

[13] Nan Zhang, Shijie Zheng, and Dejin Chen

[14] Mohammad Malikan and Victor A Eremeyev

[15] Lala Samprit Ray and Bishweshwar Babu

[16] Lala Samprit Ray and Bishweshwar Babu

[17] Mohammad Malikan, Tomasz Wiczenbach, and Victor A Eremeyev

[18] Ying Yang, W Huang, Jan Sladek, Vladimir Sladek, Xian-Fang Li, Peter Schiavone, and P H Wen

[19] J L Li and X F Li

[20] Nan Zhang, Shijie Zheng, and Dejin Chen

[21] Mohammad Malikan and Victor A Eremeyev

[22] Mohammad Malikan, Tomasz Wiczenbach, and Victor A Eremeyev

[23] Mohammad Malikan, Victor Eremeyev, and Krzysztof Żur

[24] Junhua Xiao, Zuwei Zhang, and Xiaodong Xia

[25] Chinh Van Minh, Thom Do Van, Phung Van Minh, Chi Tho Nguyen, Trac Luat Doan, and Huu Ha Nguyen

[26] Sara Fattaheian Dehkordi and Yaghoub Tadi Beni

[27] Liang Liang Xu, Yu Fang Zheng, and Chang Ping Chen

[28] Hamed Momeni-Khabisi and Masoud Tahani

[29] Hamed Momeni-Khabisi and Masoud Tahani

[30] Mohammad Malikan and Victor A Eremeyev

[31] Zuwei Zhang, Junhua Xiao, and Xiaodong Xia

[32] Swarnava Ghosh

[33] Fengyu Jiao, Zhongxian Liu, Jinghong Liu, and Mingyang Pan

[34] Olha Hrytsyna, Jan Sladek, Vladimir Sladek, and Maryan Hrytsyna

[35] Richa Kumari, Santosh Kapuria, and Santan Kumar

[36] Mahargha Biswas and Sanjeev A Sahu

[37] Mahargha Biswas and Sanjeev A Sahu

[38] Mahargha Biswas and Sanjeev A Sahu

[39] Sayantan Guha, Vipin Gupta, Mahargha Biswas, A K Singh, and M S Barak

[40] Mohammad Malikan and Victor A Eremeyev

[41] Yu-fang Zheng, Bo-wen Liu, Feng Wang, and Chang-ping Chen

[42] Mohammad Malikan and Victor A Eremeyev

[43] Eugene A Eliseev, Anna N Morozovska, Maya D Glinchuk, and R Blinc

[44] J X Zhang, R J Zeches, Q He, Y H Chu, and R Ramesh

[45] Jin Hong Lee, Kwang-Eun Kim, Byung-Kweon Jang, Ahmet A Ünal, Sergio Valencia, Florian Kronast, Kyung-Tae Ko, Stefan Kowarik, Jan Seidel, and Chan-Ho Yang

[46] Hitesh Borkar, Vishwajit M Gaikwad, R J Choudhary, M Tomar, Vinay Gupta, and Ashok Kumar

[47] Pavlo Makushko, Tobias Kosub, Oleksandr V Pylypovskyi, Natascha Hedrich, Jiang Li, Alexej Pashkin, Stanislav Avdoshenko, René Hübner, Fabian Ganss, Daniel Wolf, Axel Lubk, Maciej Oskar Liedke, Maik Butterling, Andreas Wagner, Kai Wagner, Brendan J Shields. Flexomagnetism and vertically graded néel temperature of antiferromagnetic cr2o3 thin films

[48] I Mallek-Zouari, W Ben Taazayet, J M Grenèche, L Bessais, B Dkhil, and N Thabet Mliki

[49] Zachary LaDuca, Tamalika Samanta, Nicholas Hagopian, Taehwan Jung, Katherine Su, Konrad Genser, Karin M Rabe, Paul M Voyles, Michael S Arnold, and Jason K Kawasaki

[50] Lala Samprit Ray and Bishweshwar Babu

[51] Nan Zhang, Shijie Zheng, and Dejin Chen

[52] Adam Sky, David Codony, Stephan Rudykh, Andreas Zilian, Stéphane P A Bordas, and Patrizio Neff

[53] Shenjie Zhou, Anqing Li, and Binglei Wang

[54] Sai Sidhardh and Manas C Ray

[55] David J Griffiths

[56] Luis Dorfmann and Ray W Ogden

The computational domain requires careful geometric partitioning to align the 1D and 2D spaces, constructing the overall 2D mesh (omegabeam ∪ omegaair) by discretizing the beam body and surrounding air regions independently. The overall domain is partitioned into left air, right air, top air, bottom air regions enclosing the beam body. p. 6

Where the paper says it

1 Discretization and Finite Element Spaces The computational domain requires careful geometric partitioning to align the 1D and 2D spaces. The overall 2D mesh (Ωbeam ∪ Ωair) is constructed by discretizing the beam body and the surrounding top, bottom, left, and right air regions independently, and subsequently gluing them together such that perfectly conforming triangular elements at all internal boundaries are guaranteed (Figure 3).

The 1D structural neutral axis is independently meshed as a line segment coincident with the longitudinal center (z = 0) of the 2D beam domain. p. 6
Where the paper says it

The overall 2D mesh (Ωbeam ∪ Ωair) is constructed by discretizing the beam body and the surrounding top, bottom, left, and right air regions independently, and subsequently gluing them together such that perfectly conforming triangular elements at all internal boundaries are guaranteed (Figure 3). The 1D structural neutral axis (Ω1D) is independently meshed as a line segment that is coincident with the longitudinal center (z = 0) of the 2D beam domain.

For finite element function spaces, continuous quadratic Lagrange elements P2 are selected for primary kinematic variables (u, w, ϕ) on the 1D mesh and scalar magnetic potential (ψ) on the 2D mesh. p. 6
Where the paper says it

The 1D neutral axis is embedded along z = 0 within the beam body. For the finite element function spaces, continuous quadratic Lagrange elements P2 are selected for all primary kinematic variables (u, w, ϕ) on the 1D mesh and the scalar magnetic potential (ψ) on the 2D mesh.

The iterative solution algorithm employs a staggered fixed-point iteration scheme to decouple continuous formulations into sequential boundary-value problems. The process initializes with a zero magnetic potential field (ψ0 = 0). p. 6

Where the paper says it

Let the superscript i denote the current iteration step, and i − 1 denote known quantities passed from the preceding iteration. The iterative process is initialized with a zero magnetic potential field (ψ 0 = 0).

Each iteration involves four steps: Magnetic Load Projection (2D to 1D), Structural Subproblem Update (1D), Kinematic Field Mapping (1D to 2D), and Magnetic Subproblem Update (2D). p. 7
Where the paper says it

Structural Subproblem Update: Utilizing these static magnetic loads, the 1D mechanical weak form, Equation (16a), is solved to determine the current kinematic variables (u i , wi , ϕi ). Kinematic Field Mapping (1D to 2D): The newly computed 1D mechanical displacements (u i , wi , ϕi ) are mapped from the neutral axis throughout the 2D beam body.

The convergence criterion requires the error defined by Errorw = qR 1D w(k) − w(k−1)2 dx / qR 1D w(k)2 dx falls below a tolerance threshold of tol = 10−9 between consecutive iterations. p. 7
Where the paper says it

This process is repeated until numerical convergence is achieved. The convergence criterion requires that the error defined by, Errorw = qR 1D w(k) − w(k−1)2 dx qR 1D w(k) 2 dx , (17) falls below a tolerance threshold (tol = 10−9 ) between consecutive iterations (k and k − 1).

The verification study showed good agreement with analytical results when the air domain was suppressed by assuming a very small value of magnetic permeability of air, µ0 = 10−20 N/A2. The analysis of magnetic quantities in Figure 4 shows that the B and H field outside the beam body show similar distributions, but due to strong magnetoelastic coupling inside the beam body, H reverses relative to the B field especially around the middle of the beam. p. 8

Where the paper says it

From Figures 4b and 4c and Figures 4e and 4f, it is observed that the B and H field outside the beam body show similar distributions. However, due to strong magnetoelastic coupling inside the beam body, H reverses relative to the B field especially around the middle of the beam.

The most significant result is a pattern shown in Figure 4f which shows a clear source region at the bottom of a flexomagnetic beam and a sink region formed at its top due to a constant strain gradient across the thickness of the beam. p. 8
Where the paper says it

The most interesting plot is the pattern of vector plot shown in Figure 4f which shows a clear source region at the bottom of a flexomagnetic beam and a sink region formed at its top due to a constant strain gradient across the thickness of the beam. This result is significant because it is a numerical analysis of a non-negligible magnetic quantity in air due to a bending flexomagnetic structure.

The study successfully presented a hybrid 1D-2D finite element framework to evaluate external magnetic signatures of piezo-fexomagnetic beams. By coupling a 1D Timoshenko beam model with a 2D cross-sectional magnetic domain, the framework replaces the simplifying magnetic isolation assumption prevalent in current piezoflexomagnetic beam literature with magnetic interface conditions. The framework is validated against established analytical beam problems for magnetically isolated cases by reducing the magnetic permeability of air. Sensitivity analysis revealed the dominant material parameters affecting a transduced magnetic quantity in a bending flexomagnetic or piezo-flexomagnetic beam.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved AI systems can accurately predict external magnetic flux density in air generated by piezo-flexomagnetic nanobeams using a coupled 1D-2D finite element framework. This allows for the design of non-contact magnetoelastic sensing systems by quantifying the external transverse magnetic flux density Bz.

  2. The improved system can incorporate material parameter sensitivity analysis to identify which parameters most strongly influence the external magnetic signal. This provides actionable insights for designing nanoscale sensors, as shown by finding that the dominating effect of the permeability of air domain in Figure 7 signifies that a highly permeable external material would result in a higher Bz.

  3. The system can perform rigorous verification against analytical solutions for magnetically isolated beams and compare numerical results with experimental data. This ensures the model's reliability, as the study shows good agreement with analytical results in Table 1.

Abstract

Most theoretical models of piezo-flexomagnetic nanostructures forcibly impose magnetic isolation at the structure-air interface, neglecting the external magnetic domain entirely. This mathematical compromise limits the model's capability to account for stray-field behavior in non-contact applications. To overcome this gap, our study proposes a fully coupled hybrid finite element formulation combining a 1D Timoshenko beam model with a 2D magneto-static problem, encompassing both the beam body and the surrounding air domain. By continuously mapping 1D structural kinematics into the 2D space to define the mechanically induced magnetic flux, and subsequently integrating the resulting 2D scalar potential back into 1D static generalized magnetic loads, this framework enhances the capability of the simple 1D beam model. The results present the distribution of an external magnetic flux in piezo-flexomagnetic structures and identify the material parameters driving this. Ultimately, the proposed computational method extends the boundary of a 1D beam model to an infinite-domain multiphysics environment.

Sources

Related papers