Micromechanical insights into unconstrained grain boundary sliding

arXiv:2604.16026 · cond-mat.mtrl-sci · Submitted 2026-04-17 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.

Kai: I'm Kai.

Mira: And I'm Mira, here with Lev.

Kai: We're looking at the paper: "Micromechanical insights into unconstrained grain boundary sliding".

Mira: Here's the gist of the paper. Grain boundary sliding (GBS) is governed by dislocation-mediated processes rather than diffusion-controlled mechanisms in unconstrained conditions The activation energy Q for GBS was determined to be 234 kJ mol−1, which is attributed to grain boundary diffusion-controlled motion of grain boundary dislocations involving their formation and subsequent glide along the boundary This study demonstrates that the high strain-rate sensitivity commonly observed in polycrystalline GBS originates primarily from accommodation processes rather than the intrinsic sliding mechanism.

Kai: Intrinsic Mechanism Isolation The researchers investigated dislocation-mediated unconstrained GBS using Ni bicrystal micropillars containing a single high-angle grain boundary.

Mira: By comparing bicrystal and single-crystal responses, the intrinsic contribution of GBS was isolated.

Kai: The strain-rate sensitivity remained low (SRS ≈ 0.034 ± 0.017), comparable to room temperature values, indicating the absence of diffusion-controlled accommodation mechanisms.

Paper summary: Kai: So we've looked at "Micromechanical insights into unconstrained grain boundary sliding," and the core finding is that the high strain-rate sensitivity commonly seen in polycrystalline GBS originates primarily from accommodation processes, not the intrinsic sliding mechanism itself.

Mira: And they quantified this by finding an activation energy of two hundred thirty-four kJ mol−one which they attribute to grain boundary diffusion-assisted glide of grain boundary dislocations involving their formation and subsequent glide along the boundary five <ref:2604.16026#pg1,grain boundary diffusion-assisted glide>.

Lev: For us building error correction hardware, it means that when we try to model GBS, we have to be careful; if we assume it’s just intrinsic sliding, our models will be off because they aren't accounting for those accommodation constraints.

Kai: The implication is that for things like grain boundary engineering or boundary character control, isolating the intrinsic GBS characteristics is essential because the diversity of grain boundary types in polycrystals complicates systematic investigation two <ref:2604.16026#pg2,the diversity of grain boundary types in polycrystals complicates systematic investigation>.

Mira: They used small-scale mechanical testing, specifically bicrystal micropillars fabricated using focused ion beam milling, to overcome those limitations by eliminating constraints from triple junctions and allowing direct investigation of unconstrained GBS two <ref:2604.16026#pg2>.

Lev: The paper flags a limitation: they are focusing on isolating the intrinsic contribution by comparing bicrystal and single-crystal responses, but this study doesn't necessarily tell us how that intrinsic sliding would behave under real operating conditions with external stresses.

Kai: So, the title points toward getting these micromechanical insights into unconstrained GBS, and the authors provide a quantitative basis for assessing the underlying rate-controlling mechanisms using those specific parameters.

Conclusion: Kai: So we've looked at "Micromechanical insights into unconstrained grain boundary sliding," and they’re focusing on how to separate the actual sliding from all those other things happening around it in real materials.

Mira: They are looking at this using Ni bicrystal micropillars, which is a specific setup designed to eliminate most of the usual noise from grain boundaries.

Lev: That's smart because those triple junctions and other constraints are where all the messy accommodation stuff happens, right? You can't get the pure intrinsic sliding signal there.

Kai: Exactly. The paper isolates that intrinsic contribution by comparing bicrystal responses against single crystals, which is a key experimental move to see what the material is doing on its own.

Mira: The main finding they point to is that when you look at unconstrained GBS, the strain-rate sensitivity remains low, around zero point zero three four plus or minus zero point one seven.

Lev: That low number compared to what we usually see in polycrystalline materials suggests they are seeing something different from the high strain rates we often model for real hardware stress.

Kai: And they found that this intrinsic mechanism is controlled by dislocation activity at grain boundaries, not diffusion processes, which is important because it changes how you predict material response.

Mira: The activation energy they determined was two hundred thirty-four kilo joules per mole, which they link to grain boundary diffusion assisted glide of those dislocations.

Lev: Two three four kilo joules per mole puts that squarely between the values for grain boundary diffusion and lattice diffusion, which is a nice placement on the scale.

Kai: It shows that if you're building error correction hardware based on GBS models, you need to account for those specific dislocation glide processes rather than just assuming a general diffusion rate.

Mira: It means we need to be careful with our assumptions about accommodation mechanisms when we talk about boundary character control in these materials.

Lev: So the real question is how does this intrinsic sliding change the way we design stress management strategies in complex polycrystalline structures?

Divya Sri Bandla, Subin Lee, *Christoph Kirchlechner

Institute for Applied Materials, Karlsruhe Institute of Technology

cond-mat.mtrl-sci

Submitted: 2026-04-17

Updated: 2026-10-28

DOI: 10.1016/j.scriptamat.2026.117527

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 82/100

The gist: Grain boundary sliding (GBS) is governed by dislocation-mediated processes rather than diffusion-controlled mechanisms in unconstrained conditions The activation energy Q for GBS was determined to be…

Key concepts

Grain Boundary Sliding (GBS)
GBS is a deformation mechanism where adjacent grains slide past one another along their shared boundaries, typically occurring at high temperatures. In polycrystalline materials, it often requires extra processes to relieve stress.
Strain Rate Sensitivity (SRS)
SRS measures how much the material's deformation changes when the strain rate is varied. The study found a low SRS in unconstrained GBS, suggesting that the observed high SRS in bulk materials is due to accommodation mechanisms, not the fundamental sliding process.
Activation Energy (Q)
The activation energy represents the minimum energy required for GBS to occur. For this material, Q was determined to be 234 kJ mol⁻¹, which is attributed to the grain boundary diffusion-controlled motion of dislocations involved in forming and gliding along the boundary.
Bicrystal Micropillars
These are small mechanical test specimens made from Ni that contain only a single high-angle grain boundary. They were used to eliminate constraints from triple junctions, allowing researchers to study GBS under unconstrained conditions.

Terminology

Summary

Grain boundary sliding (GBS) is governed by dislocation-mediated processes rather than diffusion-controlled mechanisms in unconstrained conditions The activation energy Q for GBS was determined to be 234 kJ mol−1, which is attributed to grain boundary diffusion-controlled motion of grain boundary dislocations involving their formation and subsequent glide along the boundary This study demonstrates that the high strain-rate sensitivity commonly observed in polycrystalline GBS originates primarily from accommodation processes rather than the intrinsic sliding mechanism. p. 0

Where the paper says it

The activation energy for GBS was determined to be 234 kJ mol-1, consistent with grain boundary diffusion-assisted glide of grain boundary dislocations. These results demonstrate that the high strain-rate sensitivity commonly associated with GBS in polycrystals originates primarily from accommodation processes rather than the intrinsic sliding mechanism.

Intrinsic Mechanism Isolation

The researchers investigated dislocation-mediated unconstrained GBS using Ni bicrystal micropillars containing a single high-angle grain boundary. By comparing bicrystal and single-crystal responses, the intrinsic contribution of GBS was isolated. p. 0

Where the paper says it

Micropillar compression tests were conducted over a temperature range from room temperature to 600 °C and strain rates between 5×10-4 and 10-1 s-1. By comparing bicrystal and single-crystal responses, the intrinsic contribution of GBS was isolated.

p. 0
Where the paper says it

Micropillar compression tests were conducted over a temperature range from room temperature to 600 °C and strain rates between 5×10-4 and 10-1 s-1. By comparing bicrystal and single-crystal responses, the intrinsic contribution of GBS was isolated.

The strain-rate sensitivity remained low (SRS ≈ 0. p. 0
Where the paper says it

By comparing bicrystal and single-crystal responses, the intrinsic contribution of GBS was isolated. The strain-rate sensitivity remained low (SRS ≈ 0.

p. 0
Where the paper says it

By comparing bicrystal and single-crystal responses, the intrinsic contribution of GBS was isolated. The strain-rate sensitivity remained low (SRS ≈ 0.

034 ± 0.017), comparable to room temperature values, indicating the absence of diffusion-controlled accommodation mechanisms. p. 0
Where the paper says it

The strain-rate sensitivity remained low (SRS ≈ 0. 017), comparable to room temperature values, indicating the absence of diffusion-controlled accommodation mechanisms.

p. 0
Where the paper says it

The strain-rate sensitivity remained low (SRS ≈ 0. 017), comparable to room temperature values, indicating the absence of diffusion-controlled accommodation mechanisms.

Deformation Parameters and Temperature Effects

The activation energy for GBS was determined to be 234 kJ mol−1, consistent with grain boundary diffusion-assisted glide of grain boundary dislocations. The yield stress at 300 °C is lower than at RT, while in both cases, the yield stress at 5% plastic strain increases with the strain rate, indicating a positive SRS. p. 3

Where the paper says it

An intentional unloading segment at 5% strain was introduced to minimize effects of lateral constraints during compression. The yield stress at 300 °C is lower than at RT, while in both cases, the yield stress at 5% plastic strain increases with the strain rate, indicating a positive SRS.

The activation energies obtained for bicrystal micropillars (234 kJ mol−1) lies between the reported values for grain boundary diffusion (Qgb = 162 kJ mol-1) and lattice diffusion (QL = 278 kJ mol-1). p. 9
Where the paper says it

The behavior at elevated temperatures, where GBS is active, is of primary interest. The activation energy obtained for bicrystal micropillars (234 kJ mol⁻¹) lies between the reported values for grain boundary diffusion (Qgb = 162 kJ mol-1) [18] and lattice diffusion (QL = 278 kJ mol-1) [19].

Strain Rate Sensitivity Comparison

The SRS at RT in polycrystals (0.007 [9]) is significantly lower than in the present study. p. 4

Where the paper says it

The SRS at RT in polycrystals (~0. 007 [9]) is significantly lower than in the present study.

This result contradicts the classical observation of high SRS values of 0. p. 4
Where the paper says it

At the elevated temperature (300 °C) where GBS is active, the SRS remains comparable to that at RT (see Fig. This contradicts the classical observation of high SRS values of 0.

3–5 during GBS in polycrystals. p. 0
Where the paper says it

The activation energy for GBS was determined to be 234 kJ mol-1, consistent with grain boundary diffusion-assisted glide of grain boundary dislocations. These results demonstrate that the high strain-rate sensitivity commonly associated with GBS in polycrystals originates primarily from accommodation processes rather than the intrinsic sliding mechanism.

In contrast, unconstrained GBS in bicrystal micropillars does not require the activation of additional accommodation mechanisms. p. 4
Where the paper says it

In polycrystals, dislocation-mediated GBS sliding requires accommodation by dislocation climb [5], making the overall deformation rate sensitive to vacancy diffusion and thus increasing SRS. In contrast, unconstrained GBS in bicrystal micropillars does not require the activation of additional accommodation mechanisms.

p. 4
Where the paper says it

In polycrystals, dislocation-mediated GBS sliding requires accommodation by dislocation climb [5], making the overall deformation rate sensitive to vacancy diffusion and thus increasing SRS. In contrast, unconstrained GBS in bicrystal micropillars does not require the activation of additional accommodation mechanisms.

Temperature Dependence and Scale Influence

The activation energy obtained for bicrystal micropillars (234 kJ mol−1) lies between the reported values for grain boundary diffusion (Qgb = 162 kJ mol-1) and lattice diffusion (QL = 278 kJ mol-1). p. 9

Where the paper says it

The behavior at elevated temperatures, where GBS is active, is of primary interest. The activation energy obtained for bicrystal micropillars (234 kJ mol⁻¹) lies between the reported values for grain boundary diffusion (Qgb = 162 kJ mol-1) [18] and lattice diffusion (QL = 278 kJ mol-1) [19].

p. 9
Where the paper says it

The behavior at elevated temperatures, where GBS is active, is of primary interest. The activation energy obtained for bicrystal micropillars (234 kJ mol⁻¹) lies between the reported values for grain boundary diffusion (Qgb = 162 kJ mol-1) [18] and lattice diffusion (QL = 278 kJ mol-1) [19].

The slightly higher activation energy compared to literature values for grain boundary diffusion is likely associated with the structural complexity of the grain boundary. p. 9
Where the paper says it

Therefore, the measured activation energy reflects either the dissociation of lattice dislocations into grain boundary dislocations or the barrier associated with the motion of grain boundary dislocations along the boundary. The slightly higher activation energy compared to literature values for grain boundary diffusion may originate from the structural complexity of the grain boundary including defects or local curvatures, which can necessitate additional processes such as local climb or diffusion-assisted rearrangements during dislocation motion.

p. 9
Where the paper says it

Therefore, the measured activation energy reflects either the dissociation of lattice dislocations into grain boundary dislocations or the barrier associated with the motion of grain boundary dislocations along the boundary. The slightly higher activation energy compared to literature values for grain boundary diffusion may originate from the structural complexity of the grain boundary including defects or local curvatures, which can necessitate additional processes such as local climb or diffusion-assisted rearrangements during dislocation motion.

p. 9
Where the paper says it

Therefore, the measured activation energy reflects either the dissociation of lattice dislocations into grain boundary dislocations or the barrier associated with the motion of grain boundary dislocations along the boundary. The slightly higher activation energy compared to literature values for grain boundary diffusion may originate from the structural complexity of the grain boundary including defects or local curvatures, which can necessitate additional processes such as local climb or diffusion-assisted rearrangements during dislocation motion.

Post-deformation observations of pillars deformed at the highest temperatures indicate the formation of a thick oxide scale on the pillar surface. p. 9
Where the paper says it

This behavior is not intrinsic to GBS, as it also appears in single crystals. Post-deformation observations of pillars deformed at the highest temperatures indicate the formation of a thick oxide scale on the pillar surface.

Summary of Findings

The measured strain-rate sensitivity remained low (SRS ≈ 0.034 ± 0.017), indicating that, in the absence of accommodation constraints, GBS is governed by dislocation-mediated processes rather than diffusion-controlled mechanisms. p. 0

Where the paper says it

017), comparable to room temperature values, indicating the absence of diffusion-controlled accommodation mechanisms. The activation energy for GBS was determined to be 234 kJ mol-1, consistent with grain boundary diffusion-assisted glide of grain boundary dislocations.

The activation energy Q for GBS was determined to be 234 ± 30 kJ mol−1, which is attributed to grain boundary diffusion-controlled motion of grain boundary dislocations involving their formation and subsequent glide along the boundary. p. 0
Where the paper says it

017), comparable to room temperature values, indicating the absence of diffusion-controlled accommodation mechanisms. The activation energy for GBS was determined to be 234 kJ mol-1, consistent with grain boundary diffusion-assisted glide of grain boundary dislocations.

Overall, the results demonstrate that the high strain-rate sensitivity commonly observed in polycrystalline GBS originates primarily from accommodation processes, whereas the intrinsic GBS mechanism is controlled by dislocation activity at grain boundaries. p. 0
Where the paper says it

These results demonstrate that the high strain-rate sensitivity commonly associated with GBS in polycrystals originates primarily from accommodation processes rather than the intrinsic sliding mechanism. Keywords Grain boundary sliding, strain rate sensitivity, activation energy, micropillar compression Grain boundary sliding (GBS) is a major deformation mechanism at high homologous temperatures in polycrystalline materials, where adjacent grains slide relative to each other under an applied stress [1,2].

Supplementary material

Figure 1 depicts the secondary electron images of 1 µm pillars deformed at 300 °C with strain rates 10-1, 10-3, and 5×10-4 s-1. Since the micropillars exposed to elevated temperatures showed the formation of oxide scale (Fig. p. 5

Where the paper says it

At higher temperatures (500 and 600 °C, shown in Fig. 3c and 3d, respectively), however, the slip traces are no longer visible, possibly due to oxide scale formation on the pillar surface.

3 of the manuscript), additional experiments have been carried out to assess the influence of oxide scale. p. 5
Where the paper says it

At higher temperatures (500 and 600 °C, shown in Fig. 3c and 3d, respectively), however, the slip traces are no longer visible, possibly due to oxide scale formation on the pillar surface.

No significant change in the yield strength is observed for pillars exposed to 300 °C compared with as-fabricated (Fig. p. 3
Where the paper says it

Similarly, GBS was also observed at 300 °C and other strain rates of 5×10-4, 10-3, and 10-1 s-1 (see supplementary material). Secondary electron images of (a) a fabricated bicrystal micropillar (d = 1 µm), highlighting the HAGB with yellow arrows and the micropillar compression loading direction with a black arrow, and (b) and (c) are pillars deformed to a strain of 0.

2a). However, exposure to 500 °C results in a slight decrease (50 MPa) in the yield strength, while exposure to 600 °C leads to a pronounced reduction of approximately 150 MPa relative to the as-fabricated pillars.

Figure 2 shows representative stress-strain curves of 1 µm pillars deformed at (a) RT and (b) 300 °C with strain rates from 10-1 to 5 × 10-4 s−1. p. 5

Where the paper says it

Representative stress-strain curves of 1 µm pillars deformed at (a) RT and (b) 300 °C with strain rates from 10-1 to 5 × 10-4 s-1. (c) is the determination of SRS at RT and 300 °C, where each data point is from an individual micropillar compression test.

The activation energy, Q, of unconstrained GBS was determined from bicrystal micropillar compression over a range of temperatures from RT to 600 °C at a strain rate of 10-3 s−1. p. 5
Where the paper says it

(c) is the determination of SRS at RT and 300 °C, where each data point is from an individual micropillar compression test. The activation energy, Q, of unconstrained GBS, was determined from bicrystal micropillar compression over a range of temperatures from RT to 600 °C at a strain rate of 10-3 s-1.

GBS was observed in the temperature range of 250 to 600 °C. p. 5
Where the paper says it

The activation energy, Q, of unconstrained GBS, was determined from bicrystal micropillar compression over a range of temperatures from RT to 600 °C at a strain rate of 10-3 s-1. GBS was observed in the temperature range of 250 to 600 °C.

p. 5
Where the paper says it

The activation energy, Q, of unconstrained GBS, was determined from bicrystal micropillar compression over a range of temperatures from RT to 600 °C at a strain rate of 10-3 s-1. GBS was observed in the temperature range of 250 to 600 °C.

At lower temperatures within this range (up to 400 °C), slip traces are visible in both grains, corresponding to (111) [101] in [324] grain and (111) [011] in [344], as highlighted by colored dashed lines in Fig. p. 5
Where the paper says it

Representative micrographs of deformed pillars within the GBS regime are shown in Figs. At lower temperatures within this range (up to 400 °C), slip traces are visible in both grains, corresponding to (111) [101] in [324] grain and (111) [ 011] in [344], as highlighted by colored dashed lines in Fig.

3a and Fig. p. 2
Where the paper says it

A small piece measuring 7×3×2 mm was mechanically polished and vibropolished prior to micropillar fabrication. The normal directions of the two grains were [ 344] and [ 324], and the grain boundary was inclined by approximately 35° relative to the sample surface (Fig.

3b. At higher temperatures (500 and 600 °C, shown in Fig. p. 5
Where the paper says it

3a and Fig. At higher temperatures (500 and 600 °C, shown in Fig.

3c and 3d, respectively), however, the slip traces are no longer visible. p. 5
Where the paper says it

At higher temperatures (500 and 600 °C, shown in Fig. 3c and 3d, respectively), however, the slip traces are no longer visible, possibly due to oxide scale formation on the pillar surface.

Figure 5 shows both [344] single-crystal and bicrystal micropillars exhibit a gradual decrease in yield stress from RT to 500 °C and 250 °C, respectively. p. 8

Where the paper says it

As shown in Fig. 5, both [344] single-crystal and bicrystal micropillars exhibit a gradual decrease in yield stress from RT to 500 °C and 250 °C, respectively.

At low temperatures, the activation energies are 28 ± 4 and 43 ± 4 kJ mol-1 for [344] single-crystal and bicrystal pillars, respectively. p. 8
Where the paper says it

This transition is reflected in the corresponding activation energies. At low temperatures, the activation energies are 28 ± 4 and 43 ± 4 kJ mol-1 for [344] single-crystal and bicrystal pillars, respectively.

These values increase to 532 ± 41 and 234 ± 30 kJ mol-1 at elevated temperatures. p. 8
Where the paper says it

At low temperatures, the activation energies are 28 ± 4 and 43 ± 4 kJ mol-1 for [344] single-crystal and bicrystal pillars, respectively. These values increase to 532 ± 41 and 234 ± 30 kJ mol-1 at elevated temperatures.

At low temperatures (RT to 500 °C for single crystals and up to 250 °C for bicrystals until GBS activates), the measured activation energies are consistent with dislocation glide as the rate-controlling mechanism. p. 8
Where the paper says it

These values increase to 532 ± 41 and 234 ± 30 kJ mol-1 at elevated temperatures. At low temperatures (RT to 500 °C for single crystals and up to 250 °C for bicrystals until GBS activates), the measured activation energies are consistent with dislocation glide as the rate-controlling mechanism [17].

The slightly higher value observed in micropillars compared to bulk FCC metals can be attributed to size effects, particularly the influence of free surfaces and limited dislocation sources. p. 8
Where the paper says it

At low temperatures (RT to 500 °C for single crystals and up to 250 °C for bicrystals until GBS activates), the measured activation energies are consistent with dislocation glide as the rate-controlling mechanism [17]. The slightly higher value observed in micropillars compared to bulk FCC metals can be attributed to size effects, particularly the influence

Figure 5 shows that on a semi-logarithmic plot of yield stress versus the inverse of temperature, the slope of the data represents the activation energy. p. 7

Where the paper says it

314 J mol-1 K-1), and n is the stress exponent, which can also be considered as the inverse of SRS. After rearranging the equation, σ 1/ SRS ∝ exp( Q RT ) (2) Therefore, on a semi-logarithmic plot of yield stress versus the inverse of temperature, the slope of the data represents the activation energy.

Since there is no clear difference between the SRS under GBS and non-GBS conditions (see Fig. p. 7
Where the paper says it

After rearranging the equation, σ 1/ SRS ∝ exp( Q RT ) (2) Therefore, on a semi-logarithmic plot of yield stress versus the inverse of temperature, the slope of the data represents the activation energy. Since there is no clear difference between the SRS under GBS and non-GBS conditions (see Fig.

2c), SRS has been set to 0. p. 7
Where the paper says it

Since there is no clear difference between the SRS under GBS and non-GBS conditions (see Fig. 2c), SRS has been set to 0.

04 for calculating Q using equation 2. p. 7
Where the paper says it

2c), SRS has been set to 0. 04 for calculating Q using equation 2.

The activation energy obtained for bicrystal micropillars (234 kJ mol−1) lies between the reported values for grain boundary diffusion (Qgb = 162 kJ mol-1) and lattice diffusion (QL = 278 kJ mol-1). The slightly higher activation energy compared to literature values for grain boundary diffusion is likely associated with the structural complexity of the grain boundary.

--- Page 1 ---

Mircomechanical insights into unconstrained grain boundary sliding

Divya Sri Bandla1, Subin Lee1, Christoph Kirchlechner1 Institute for Applied Materials, Karlsruhe Institute of Technology, Karlsruhe 76131, Germany Corresponding author: Subin Lee (subin.lee@kit.edu) Abstract Grain boundary sliding (GBS) is a key deformation mechanism at high homologous temperatures in polycrystalline materials. p. 0

Where the paper says it

1 Mircomechanical insights into unconstrained grain boundary sliding Divya Sri Bandla1 , Subin Lee1,*, Christoph Kirchlechner1 1 Institute for Applied Materials, Karlsruhe Institute of Technology, Karlsruhe 76131, Germany * Corresponding author: Subin Lee (subin. edu) Abstract Grain boundary sliding (GBS) is a key deformation mechanism at high homologous temperatures in polycrystalline materials, however, its intrinsic behavior is often obscured by additional strain accommodation processes.

In this study, dislocation-mediated unconstrained GBS was investigated using Ni bicrystal micropillars containing a single high-angle grain boundary. p. 0
Where the paper says it

edu) Abstract Grain boundary sliding (GBS) is a key deformation mechanism at high homologous temperatures in polycrystalline materials, however, its intrinsic behavior is often obscured by additional strain accommodation processes. In this study, dislocation-mediated unconstrained GBS was investigated using Ni bicrystal micropillars containing a single high-angle grain boundary.

Micropillar compression tests were conducted over a temperature range from room temperature to 600 °C and strain rates between 5×10-4 and 10-1 s-1. p. 0
Where the paper says it

In this study, dislocation-mediated unconstrained GBS was investigated using Ni bicrystal micropillars containing a single high-angle grain boundary. Micropillar compression tests were conducted over a temperature range from room temperature to 600 °C and strain rates between 5×10-4 and 10-1 s-1.

By comparing bicrystal and single-crystal responses, the intrinsic contribution of GBS was isolated. The strain-rate sensitivity remained low (SRS ≈ 0.034 ± 0.017), comparable to room temperature values, indicating the absence of diffusion-controlled accommodation mechanisms. The activation energy for GBS was determined to be 234 kJ mol-1, consistent with grain boundary diffusion-assisted glide of grain boundary dislocations. p. 0
Where the paper says it

017), comparable to room temperature values, indicating the absence of diffusion-controlled accommodation mechanisms. The activation energy for GBS was determined to be 234 kJ mol-1, consistent with grain boundary diffusion-assisted glide of grain boundary dislocations.

These results demonstrate that the high strain-rate sensitivity commonly associated with GBS in polycrystals originates primarily from accommodation processes rather than the intrinsic sliding mechanism. p. 0
Where the paper says it

The activation energy for GBS was determined to be 234 kJ mol-1, consistent with grain boundary diffusion-assisted glide of grain boundary dislocations. These results demonstrate that the high strain-rate sensitivity commonly associated with GBS in polycrystals originates primarily from accommodation processes rather than the intrinsic sliding mechanism.

Keywords Grain boundary sliding, strain rate sensitivity, activation energy, micropillar compression. p. 0
Where the paper says it

These results demonstrate that the high strain-rate sensitivity commonly associated with GBS in polycrystals originates primarily from accommodation processes rather than the intrinsic sliding mechanism. Keywords Grain boundary sliding, strain rate sensitivity, activation energy, micropillar compression Grain boundary sliding (GBS) is a major deformation mechanism at high homologous temperatures in polycrystalline materials, where adjacent grains slide relative to each other under an applied stress [1,2].

--- Page 2 ---

Grain boundary sliding (GBS) is a major deformation mechanism at high homologous temperatures in polycrystalline materials. It is typically characterized by a high strain-rate sensitivity (SRS ≈ 0. p. 0

Where the paper says it

Keywords Grain boundary sliding, strain rate sensitivity, activation energy, micropillar compression Grain boundary sliding (GBS) is a major deformation mechanism at high homologous temperatures in polycrystalline materials, where adjacent grains slide relative to each other under an applied stress [1,2]. It is typically characterized by a high strain-rate sensitivity (SRS ≈ 0.

3–5), and an activation energy Q comparable to that of grain boundary diffusion [3,4]. p. 0
Where the paper says it

017), comparable to room temperature values, indicating the absence of diffusion-controlled accommodation mechanisms. The activation energy for GBS was determined to be 234 kJ mol-1, consistent with grain boundary diffusion-assisted glide of grain boundary dislocations.

However, GBS in polycrystalline materials causes compatibility stress at grain boundary triple junctions and therefore requires an accommodation mechanism, such as dislocation climb, to relieve stress concentrations and further progress of GBS [5]. p. 1
Where the paper says it

2 grain boundary diffusion [3,4]. However, GBS in polycrystalline materials causes compatibility stress at grain boundary triple junctions and therefore requires an accommodation mechanism, such as dislocation climb, to relieve stress concentrations and further progress of GBS [5].

Consequently, when deformation is limited by accommodation mechanisms, the experimentally measured SRS and Q values reflect the accommodation processes rather than intrinsic GBS. p. 1
Where the paper says it

However, GBS in polycrystalline materials causes compatibility stress at grain boundary triple junctions and therefore requires an accommodation mechanism, such as dislocation climb, to relieve stress concentrations and further progress of GBS [5]. Consequently, when deformation is limited by accommodation mechanisms, the experimentally measured SRS and Q values reflect the accommodation processes rather than intrinsic GBS, rendering a thorough understanding of GBS in polycrystalline materials challenging.

How the training signal is built

The authors employed small-scale mechanical testing to overcome limitations by enabling the isolation of specific microstructural features. Bicrystal micropillars containing a single grain boundary can be fabricated using focused ion beam (FIB) milling, eliminating constraints from triple junctions and allowing direct investigation of unconstrained GBS. p. 1

Where the paper says it

Small-scale mechanical testing provides an effective approach to overcome these limitations by enabling the isolation of specific microstructural features. Bicrystal micropillars containing a single grain boundary can be fabricated using focused ion beam (FIB) milling, eliminating constraints from triple junctions and allowing direct investigation of unconstrained GBS.

p. 1
Where the paper says it

Small-scale mechanical testing provides an effective approach to overcome these limitations by enabling the isolation of specific microstructural features. Bicrystal micropillars containing a single grain boundary can be fabricated using focused ion beam (FIB) milling, eliminating constraints from triple junctions and allowing direct investigation of unconstrained GBS.

Previous studies on β-Sn [6] and Al [7] demonstrated GBS in such micropillars at room temperature (RT) due to the low melting points, quantifying strain contributions of GBS, as well as size effects. p. 1
Where the paper says it

Bicrystal micropillars containing a single grain boundary can be fabricated using focused ion beam (FIB) milling, eliminating constraints from triple junctions and allowing direct investigation of unconstrained GBS. Previous studies on β-Sn [6] and Al [7] demonstrated GBS in such micropillars at room temperature (RT) due to the low melting points, quantifying strain contributions of GBS, as well as size effects.

p. 1
Where the paper says it

Bicrystal micropillars containing a single grain boundary can be fabricated using focused ion beam (FIB) milling, eliminating constraints from triple junctions and allowing direct investigation of unconstrained GBS. Previous studies on β-Sn [6] and Al [7] demonstrated GBS in such micropillars at room temperature (RT) due to the low melting points, quantifying strain contributions of GBS, as well as size effects.

Where the gains come from

In their recent work, they demonstrated unconstrained GBS in Ni bicrystal micropillars containing a random high-angle grain boundary (HAGB) at 250–300 °C. Based on the observations of dislocation activities along the GB and inverse dependence of activation stress on pillar diameter, the sliding mechanism was identified as dislocation-mediated. p. 1

Where the paper says it

In our recent work, we demonstrated unconstrained GBS in Ni bicrystal micropillars containing a random high-angle grain boundary (HAGB) at 250–300 °C [8]. Based on the observations of dislocation activities along the GB and inverse dependence of activation stress on pillar diameter, the sliding mechanism was identified as dislocation-mediated.

Complementary experiments were performed on single-crystal micropillars under identical conditions. p. 1
Where the paper says it

In this study, micropillar compression tests were conducted over a temperature range from RT to 600 °C to quantify the SRS and Q of dislocation-mediated unconstrained GBS. Complementary experiments were performed on single-crystal micropillars under identical conditions.

The comparison of the deformation response and the corresponding SRS and Q values between bicrystal and single-crystal pillars enables isolation of the intrinsic GBS contribution. p. 2
Where the paper says it

3 SRS and Q values between bicrystal and single-crystal pillars enables isolation of the intrinsic GBS contribution and provides a quantitative basis for assessing the underlying rate-controlling mechanisms. A Ni bicrystal containing a random HAGB of misorientation 20° was grown by the Bridgman method.

Mechanism Interpretation

The SRS measured here is consistent with reported values for Ni single-crystal micropillars at RT, which is approximately 0.037 [14]. At the elevated temperature (300 °C) where GBS is active, the SRS remains comparable to that at RT. p. 4

Where the paper says it

The SRS measured here is consistent with reported values for Ni single-crystal micropillars at RT, which is approximately 0. At the elevated temperature (300 °C) where GBS is active, the SRS remains comparable to that at RT (see Fig.

This contradicts the classical observation of high SRS values of 0. p. 4
Where the paper says it

At the elevated temperature (300 °C) where GBS is active, the SRS remains comparable to that at RT (see Fig. This contradicts the classical observation of high SRS values of 0.

3–5 during GBS in polycrystals [3]. p. 0
Where the paper says it

The activation energy for GBS was determined to be 234 kJ mol-1, consistent with grain boundary diffusion-assisted glide of grain boundary dislocations. These results demonstrate that the high strain-rate sensitivity commonly associated with GBS in polycrystals originates primarily from accommodation processes rather than the intrinsic sliding mechanism.

In contrast, unconstrained GBS in bicrystal micropillars does not require the activation of additional accommodation mechanisms. As a result, deformation remains governed by dislocation processes similar to those at RT. p. 4
Where the paper says it

In contrast, unconstrained GBS in bicrystal micropillars does not require the activation of additional accommodation mechanisms. As a result, deformation remains governed by dislocation processes similar to those at RT, leading to comparable SRS values.

Activation Energy Determination

The activation energy Q was determined from bicrystal micropillar compression over a range of temperatures from RT to 600 °C at a strain rate of 10-3 s−1. GBS was observed in the temperature range of 250 to 600 °C. The activation energy obtained for bicrystal micropillars (234 kJ mol−1) lies between the reported values for grain boundary diffusion (Qgb = 162 kJ mol-1) and lattice diffusion (QL = 278 kJ mol-1). The slightly higher activation energy compared to literature values for grain boundary diffusion is likely associated with the structural complexity of the grain boundary.

Conclusion on GBS Control

Overall, the results demonstrate that the high strain-rate sensitivity commonly observed in polycrystalline GBS originates primarily from accommodation processes, whereas the intrinsic GBS mechanism is controlled by dislocation activity at grain boundaries. The activation energy Q for GBS was determined to be 234 kJ mol−1, which is attributed to grain boundary diffusion-controlled motion of grain boundary dislocations involving their formation and subsequent glide along the boundary. p. 0

Where the paper says it

017), comparable to room temperature values, indicating the absence of diffusion-controlled accommodation mechanisms. The activation energy for GBS was determined to be 234 kJ mol-1, consistent with grain boundary diffusion-assisted glide of grain boundary dislocations.

The slightly elevated value compared to literature grain boundary diffusion is likely associated with the structural complexity of the grain boundary. p. 9
Where the paper says it

Therefore, the measured activation energy reflects either the dissociation of lattice dislocations into grain boundary dislocations or the barrier associated with the motion of grain boundary dislocations along the boundary. The slightly higher activation energy compared to literature values for grain boundary diffusion may originate from the structural complexity of the grain boundary including defects or local curvatures, which can necessitate additional processes such as local climb or diffusion-assisted rearrangements during dislocation motion.

Acknowledgment

The authors express their gratitude to the Deutsche Forschungsgemeinschaft (DFG) for its financial support within project 500076185 “Micromechanical characterization of grain boundary slip: Towards a deformation mechanism map”.

Declaration of competing interest

No potential conflict of interest was reported by the author(s).

Data availability

Data will be made available on request.

--- Page 3 ---

A quantitative understanding of intrinsic GBS requires deformation parameters under unconstrained conditions, i.e., in the absence of accommodation mechanisms. p. 0

Where the paper says it

The strain-rate sensitivity remained low (SRS ≈ 0. 017), comparable to room temperature values, indicating the absence of diffusion-controlled accommodation mechanisms.

This is particularly relevant for grain boundary engineering approaches, such as solute segregation or boundary character control, where isolating the intrinsic GBS characteristics is essential. p. 1
Where the paper says it

, in the absence of accommodation mechanisms. This is particularly relevant for grain boundary engineering approaches, such as solute segregation or boundary character control, where isolating the intrinsic GBS characteristics is essential.

In addition, the diversity of grain boundary types in polycrystals complicates systematic investigation of the effect of boundary character on GBS behavior. p. 1
Where the paper says it

This is particularly relevant for grain boundary engineering approaches, such as solute segregation or boundary character control, where isolating the intrinsic GBS characteristics is essential. In addition, the diversity of grain boundary types in polycrystals complicates systematic investigation of the effect of boundary character on GBS behavior.

Pruning redundant reasoning tokens

The authors employed small-scale mechanical testing to overcome limitations by enabling the isolation of specific microstructural features. Bicrystal micropillars containing a single grain boundary can be fabricated using focused ion beam (FIB) milling, eliminating constraints from triple junctions and allowing direct investigation of unconstrained GBS. Previous studies on β-Sn [6] and Al [7] demonstrated GBS in such micropillars at room temperature (RT) due to the low melting points, quantifying strain contributions of GBS, as well as size effects.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved prediction of strain rate sensitivity in polycrystalline materials by distinguishing intrinsic sliding from accommodation mechanisms. The improved AI system can accurately predict whether a measured high strain rate sensitivity originates from grain boundary sliding or from dislocation climb, based on comparing bicrystal and single-crystal pillar responses as noted in the paper: The high strain-rate sensitivity commonly associated with GBS in polycrystals originates primarily from accommodation processes rather than the intrinsic sliding mechanism.

  2. Enhanced activation energy determination for grain boundary deformation by incorporating structural complexity effects. The improved AI system can calculate the activation energy Q more accurately by distinguishing between diffusion-controlled motion and structural complexity, as suggested by the finding that The slightly higher activation energy compared to literature values for grain boundary diffusion is likely associated with the structural complexity of the grain boundary.

  3. Refined assessment of high-temperature mechanical strength degradation due to surface effects. The improved AI system can predict apparent yield strength changes under elevated temperatures by modeling oxide scale formation, as indicated by the observation that exposure to 600 °C leads to a pronounced reduction of approximately 150 MPa relative to the as-fabricated pillars and this reduction may be attributed to the formation of an oxide scale.

Abstract

Grain boundary sliding is a key deformation mechanism at high homologous temperatures in polycrystalline materials, however, its intrinsic behavior is often obscured by strain accommodation processes. In this study, dislocation-mediated unconstrained GBS was investigated using Ni bicrystal micropillars containing a high-angle grain boundary. Micropillar compression tests were performed from room temperature to 600, C and strain rates between 5 times10-4 and 10-1, s-1. By comparing bicrystal and single-crystal responses, intrinsic contribution of grain boundary sliding was isolated. The strain-rate sensitivity remained low (0.034 plus or minus 0.017), comparable to room temperature values, indicating the absence of diffusion-controlled accommodation mechanisms. The activation energy for grain boundary sliding was determined to be 284 plus or minus 47, kJ,mol-1, consistent with lattice diffusion-assisted dissociation of lattice dislocations into grain boundary dislocations. These results demonstrate that the high strain-rate sensitivity associated with grain boundary sliding in polycrystals originates primarily from accommodation processes rather than the intrinsic sliding mechanism.

Related papers