Spurious-Free Lithium Niobate Bulk Acoustic Wave Resonator with Grounded-Ring Electrode

arXiv:2604.06426 · eess.SY, cs.SY · Submitted 2026-04-07 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Robotics Radio. Generated commentary on the latest robotics and control papers.

Rosa: I'm Rosa.

Dev: And I'm Dev, here with Taro.

Rosa: We're looking at the paper: "Spurious-Free Lithium Niobate Bulk Acoustic Wave Resonator with Grounded-Ring Electrode".

Dev: Here's the gist of the paper. High-performance piezoelectric resonators are promising energy storage elements for piezoelectric power conversion due to their compact footprint and low loss at frequencies where conventional magnetic components become bulky and inefficient.

Rosa: The proposed structure is analyzed through simulation and experimentally validated using electrical characterization and laser Doppler vibrometry (LDV) Device Performance Metrics The demonstrated device operates at 10.14 MHz and achieves an electromechanical coupling coefficient of 29.6%, a maximum in-band Bode quality factor (QBode) of 5230, and a figure of merit (FoM, Q · k2) of 1548.

Dev: These results establish the grounded-ring TE-mode LN BAW resonator as a practical platform for piezoelectric power conversion and a broader design approach for realizing high-performance spurious-free acoustic resonators.

Rosa: Spurious Mode Suppression Mechanism The mechanism for spurious-mode suppression is based on a novel electrode design The structure comprises three distinct regions: an active area defined by a signal-top and a ground-bottom electrode, a non-metalized sub-wavelength gap, and a metalized ring region surrounding the active area.

Paper summary: Dev: Looking at the title of "Spurious-Free Lithium Niobate Bulk Acoustic Wave Resonator with Grounded-Ring Electrode", what’s the big picture implication of this specific design? It sounds very focused on fixing a problem that plagues these devices.

Taro: I think it means that for high frequency acoustic applications, we can get better efficiency and bandwidth if we stop looking at just the material properties and start looking at how you structure the device boundary conditions.

Rosa: Exactly. They are showing that by adding this grounded ring, they can engineer a smoother resistance curve, which effectively eliminates those unwanted in-band spurious modes by exciting that piston-like modal response across the inductive band.

Dev: It’s about moving toward a design approach for realizing high performance spurious-free acoustic resonators, not just one specific device. This suggests a broader design principle here that might apply to other BAW applications where those modes are critical.

Taro: So, in simple terms, this paper shows how changing the geometry around the piezoelectric material—specifically with that grounded ring—allows you to maintain high performance even when you're operating right in the middle of your desired frequency range.

Rosa: It establishes the grounded-ring TE-mode resonator as a promising platform for compact, high-efficiency, and high-power-density piezoelectric power converters. That’s the practical application they are pointing toward.

Dev: Yeah, it’s a concrete result: ten point one four MHz with that specific set of numbers—k squared of twenty-nine point six percent and an FoM of one thousand five hundred forty-eight—showing a path forward for power conversion <ref:2604.06426#pg2>.

Conclusion: Rosa: So we’ve been looking at this paper about the grounded ring electrode and how it cleans up these acoustic resonators.

Dev: It’s all about getting rid of those unwanted modes that mess up your performance right when you need it most, in the in-band range.

Rosa: The authors are focusing on this specific structure to make sure you get a smooth resistance curve across the whole operating band.

Dev: They show their results using a material called lithium niobate at ten point one four megahertz and they got a figure of merit of fifteen hundred forty eight.

Rosa: That number shows they’ve built something that works well for practical piezoelectric power conversion, which is pretty significant for compact designs.

Dev: It means this isn't just a lab curiosity; it’s a platform that could actually be used in real hardware to store energy efficiently at these high frequencies.

Rosa: The big picture here is making these devices smaller and more powerful because you’re not wasting energy on those spurious modes anymore.

Dev: This design approach, using the grounded ring, might just be a useful template for other types of bulk acoustic wave devices where avoiding those unwanted noise modes is crucial.

Rosa: We’ll look at how they tested this outside the lab and if it holds up when things get messy in the real world next.

University of Texas at Austin · Stanford University · Polytec GMBH

eess.SY, cs.SY

Submitted: 2026-04-07

Updated: 2026-11-09

Comments: 15 pages, 17 figures

DOI: 10.1109/TUSON.2026.3738013

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 96/100

The gist: High-performance piezoelectric resonators are promising energy storage elements for piezoelectric power conversion due to their compact footprint and low loss at frequencies where conventional…

Key concepts

Piezoelectric Resonators
These are energy storage elements that use the mechanical vibration of a material (like Lithium Niobate) to store electrical energy and convert it back into electricity. They are promising because they are small and efficient, especially at high frequencies where traditional magnetic components become too large.
Spurious Mode Suppression
This is the process of designing a structure so that unwanted, unwanted vibrations (spurious modes) do not occur when the device is operating. The new grounded-ring electrode design achieves this by creating a smooth resistance curve, which effectively eliminates these unwanted modes in the operating frequency band.
Figure of Merit (FoM)
The FoM is a key performance metric for resonators, calculated using the quality factor (Q) and the electromechanical coupling coefficient (k²). A higher FoM indicates a better resonator because it means more energy is stored and converted efficiently at that specific frequency.

Terminology

Summary

High-performance piezoelectric resonators are promising energy storage elements for piezoelectric power conversion due to their compact footprint and low loss at frequencies where conventional magnetic components become bulky and inefficient. p. 0

Where the paper says it

1 Spurious-Free Lithium Niobate Bulk Acoustic Wave Resonator with Grounded-Ring Electrode Vakhtang Chulukhadze, Kristi Nguyen, Eric Stolt, Kilian Shambaugh, Weston Braun, Tzu-Hsuan Hsu, Osama Jameel, Juan Rivas-Davila, and Ruochen Lu 1 2 3 4 5 6 7 8 9 10 11 12 13 Abstract—High-performance piezoelectric resonators are promising energy storage elements for piezoelectric power conversion due to their compact footprint and low loss at frequencies where conventional magnetic components become bulky and inefficient. However, their practical use is often limited by the trade-off between a high electromechanical coupling coefficient (k 2 ) for wide-band operation and the emergence of spurious acoustic modes that limit the resonators’ inductive bandwidth.

The proposed structure is analyzed through simulation and experimentally validated using electrical characterization and laser Doppler vibrometry (LDV)

Device Performance Metrics

The demonstrated device operates at 10.14 MHz and achieves an electromechanical coupling coefficient of 29. p. 0

Where the paper says it

The demonstrated device operates at 10. 14 MHz and achieves an electromechanical coupling coefficient of 29.

6%, a maximum in-band Bode quality factor (QBode) of 5230, and a figure of merit (FoM, Q · k2) of 1548. p. 0
Where the paper says it

14 MHz and achieves an electromechanical coupling coefficient of 29. 6%, a maximum in-band Bode quality factor (QBode) of 5230, and a figure of merit (FoM, Q · k 2 ) of 1548.

These results establish the grounded-ring TE-mode LN BAW resonator as a practical platform for piezoelectric power conversion and a broader design approach for realizing high-performance spurious-free acoustic resonators. p. 0
Where the paper says it

6%, a maximum in-band Bode quality factor (QBode) of 5230, and a figure of merit (FoM, Q · k 2 ) of 1548. These results establish the grounded-ring TE-mode LN BAW resonator as a practical platform for piezoelectric power conversion and a broader design approach for realizing high-performance spurious-free acoustic resonators.

Spurious Mode Suppression Mechanism

The mechanism for spurious-mode suppression is based on a novel electrode design The structure comprises three distinct regions: an active area defined by a signal-top and a ground-bottom electrode, a non-metalized sub-wavelength gap, and a metalized ring region surrounding the active area. The proposed circular grounded-ring resonator design achieves a smooth resistance curve, effectively eliminating in-band spurious modes. p. 3

Where the paper says it

In contrast, the proposed circular grounded-ring TE resonator [Fig. 4 (c)] achieves a smooth resistance curve, effectively eliminating in-band spurious modes.

This suppression is achieved by exciting a piston-like modal response across the inductive band. p. 1
Where the paper says it

2 IEEE TRANSACTIONS ON ULTRASONICS Highlights • A grounded-ring electrode enables a spurious-free thickness-extensional (TE)-mode lithium niobate (LN) bulk acoustic wave (BAW) resonator, validated by simulation, electrical characterization, and laser Doppler vibrometry (LDV). • The proposed structure suppresses lateral spurious modes by altering the effective boundary conditions and exciting a piston-like modal response across the inductive band.

Acoustic Mode Selection and Material Choice

The selection process was guided by the material k2 (k2Mij), which is evaluated assuming the entire piezoelectric volume participates in the vibration. The TE mode was adopted to realize a spurious-free, high FoM acoustic resonator for piezoelectric power conversion. p. 2

Where the paper says it

In contrast, TE-mode devices benefit from dispersion characteristics that enable spurious-free acoustic resonators in RF applications [27]. Consequently, the TE-mode was adopted to realize a spurious-free, high FoM acoustic resonator for piezoelectric power conversion.

36Y LN was chosen for its high k2M33 paired with a low parasitic k2M35. p. 3
Where the paper says it

function of the rotational angle θ in ZXZ Euler angle rotation (0, 90 - θ, 0), as shown in Fig. Accordingly, 36Y LN was chosen for its high k 2 M_33 paired with a low parasitic k 2 M_35.

Experimental Validation and Comparison

The results are shown in Fig. 6 (a)-(c), closely matching the simulated results in Fig. p. 4

Where the paper says it

The results are shown in Fig. 6 (a)-(c), closely matching the simulated results in Fig.

4. The grounded-ring design exhibits a spurious-free response while yielding a k2 of 29. p. 4
Where the paper says it

6% for the rectangular and the circular reference devices, respectively [29]. In contrast, the groundedring design exhibits a spurious-free response while yielding a k 2 of 29.

6%, which closely matches the simulation and indicates minimal loss in performance. p. 4
Where the paper says it

In contrast, the groundedring design exhibits a spurious-free response while yielding a k 2 of 29. 6%, which closely matches the simulation and indicates minimal loss in performance.

The extracted key performance parameters, including k2, Q at series resonance (Qs), maximum QBode in-band (Qmax), and maximum FoM are summarized in Table II, indicating a high FoM of 1548. p. 5
Where the paper says it

On the other hand, the proposed structure yields a smoother in-band QBode, providing a wide operating region for the power converter with low loss. The extracted key performance parameters, including k 2 , Q at series resonance (Qs), maximum QBode in-band (Qmax), and maximum FoM are summarized in Table II, indicating a high FoM of 1548.

Conclusion and Generalization

The measured device achieved a spurious-free response at 10.14 MHz with k2 = 29. p. 0

Where the paper says it

The demonstrated device operates at 10. 14 MHz and achieves an electromechanical coupling coefficient of 29.

6%, a maximum in-band QBode of 5230, and an FoM of 1548. p. 0
Where the paper says it

14 MHz and achieves an electromechanical coupling coefficient of 29. 6%, a maximum in-band Bode quality factor (QBode) of 5230, and a figure of merit (FoM, Q · k 2 ) of 1548.

These results establish the groundedring TE-mode resonator as a promising platform for compact, high-efficiency, and high-power-density piezoelectric power converters. p. 0
Where the paper says it

These results establish the grounded-ring TE-mode LN BAW resonator as a practical platform for piezoelectric power conversion and a broader design approach for realizing high-performance spurious-free acoustic resonators. INTRODUCTION MODERN power electronic systems have continuously shown the need for compact power conversion with a high power density.

The design principles demonstrated here may extend to other BAW applications where spurious-mode suppression is critical. p. 2
Where the paper says it

This work addresses these fundamental limitations by implementing a novel spurious-free acoustic device design for high-frequency piezoelectric power conversion. Wideband performance suitable for a power converter was achieved using a BAW resonator operating in TE mode, with a grounded-ring structure to facilitate spurious mode suppression.

The groundedring TE-mode resonator is a promising platform for compact, high-efficiency, and high-power-density piezoelectric power converters. p. 0
Where the paper says it

These results establish the grounded-ring TE-mode LN BAW resonator as a practical platform for piezoelectric power conversion and a broader design approach for realizing high-performance spurious-free acoustic resonators. INTRODUCTION MODERN power electronic systems have continuously shown the need for compact power conversion with a high power density.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved AI can perform high-performance piezoelectric power conversion by utilizing a grounded-ring electrode architecture that suppresses lateral spurious modes across an inductive band, enabling operation at 10.14 MHz with a figure of merit of 1548.

  2. Improved AI can design acoustic resonators for power conversion by incorporating material and acoustic mode selection guided by the material k2 (k2 M ij) and selecting the thickness-extensional TE mode to minimize parasitic coupling with unwanted shear modes.

  3. Improved AI can engineer spurious-free acoustic devices by implementing a novel electrode design, specifically a grounded ring separated from the active region by a narrow gap, which modifies effective boundary conditions to excite a piston-like modal response across the inductive band.

  4. Improved AI can optimize geometric design parameters for spurious mode suppression by utilizing Lamb wave dispersion characteristics of lithium niobate to dictate optimal gap and ring widths based on the decay length of evanescent waves.

  5. Improved AI can predict and mitigate performance degradation in power converters by extracting key acoustic metrics such as k2, Q at series resonance (Qs), maximum QBode, and FoM, which are crucial for determining usable converter bandwidth and efficiency.

Abstract

High-performance piezoelectric resonators are promising energy-storage elements for piezoelectric power conversion because of their compact footprint and low loss at frequencies where conventional magnetic components become bulky and inefficient. However, their practical use is often limited by the trade-off between a high electromechanical coupling coefficient (k squared) for wide-band operation and the emergence of spurious acoustic modes that limit the resonators' inductive bandwidth. This work reports a spurious-free thickness-extensional (TE)-mode bulk acoustic wave (BAW) resonator in single-crystal lithium niobate (LN) based on a grounded-ring electrode architecture. The proposed structure is analyzed through simulation and experimentally validated using electrical characterization and laser Doppler vibrometry (LDV). The results show that the grounded ring modifies the effective boundary conditions of the acoustic device, enabling a piston-like modal response that suppresses lateral spurious modes across the inductive band. The demonstrated device operates at 10.14 MHz and achieves an electromechanical coupling coefficient of 29.6%, a maximum in-band Bode quality factor (Q Bode) of 5230, and a figure of merit (FoM, Q times k squared) of 1548. These results establish the grounded-ring TE-mode LN BAW resonator as a practical platform for piezoelectric power conversion and a broader design approach for realizing high-performance spurious-free acoustic resonators.

Sources

Related papers