The effect of Nb and O on the martensitic transformation in the Ti-Nb-O alloys

arXiv:2604.05725 · cond-mat.mtrl-sci · Submitted 2026-04-07 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.

Kai: We're looking at the paper: "The effect of Nb and O on the martensitic transformation in the Ti-Nb-O alloys".

Mira: Here's the gist of the paper. This study examines the influence of niobium and oxygen on phase stability, crystal structure, and martensitic transformation pathways in Ti–Nb–O alloys <ref:2604.05725#pg2> because it clarifies the distinct roles of these elements in governing the martensitic transformation and competitive phase formation <ref:2604.05725#pg4>.

Kai: Phase Stability and Transformation Pathways The results demonstrate that Nb primarily governs α″ martensite evolution, as increasing Nb stabilizes the β phase and shifts the α″ structure toward higher symmetry, which is reflected by systematic changes in lattice parameters and an increasing shuffle parameter y <ref:2604.05725#pg2>.

Mira: Oxygen modifies transformation pathways by suppressing the ω phase formation at lower Nb contents while promoting β→α″ transformation, but at higher Nb levels it inhibits long-range martensitic transformation resulting in retained β or competing ω phase <ref:2604.05725#pg2>.

Kai: These effects are attributed to local lattice distortions induced by interstitial oxygen <ref:2604.05725#pg2>.

Title and authors: Kai: So we're looking at this paper today titled "The effect of Nb and O on the martensitic transformation in the Ti-Nb-O alloys". We're trying to figure out how adding niobium and oxygen messes with the phase stability, crystal structure, and those martensitic transformation pathways.

Mira: Yeah, it’s about understanding exactly what those two elements are doing in controlling how this material changes shape at a microscopic level and competing phases forming at the same time.

Lev: I'm curious if they actually managed to get good enough data on the actual transformation pathways, or is this just a theoretical exercise?

Kai: They used X-ray diffraction, electron microscopy, and reciprocal space mapping to characterize the microstructure and crystallography of these Ti-Nb-O alloys. They even applied a two dimensional X ray diffraction orientation simulation approach to distinguish all twelve crystallographically equivalent martensitic variants originating from a single prior beta grain.

Mira: That sounds like they are trying to get really detailed on how those individual variants form, which is crucial for understanding the transformation process itself.

Lev: And they used that method to quantitatively evaluate the atomic shuffle parameter, y, which describes the beta-to-alpha double prime transformation. That's a specific structural metric they derived from their simulations.

Kai: Exactly; by measuring that shuffle parameter y, they can describe how the beta-to-alpha double prime transformation is happening at the atomic level.

Mira: And one of their key findings is that niobium primarily governs the evolution of the alpha double prime martensite, meaning increasing niobium stabilizes this phase.

Lev: They found that increasing niobium stabilizes the beta phase and shifts the alpha double prime structure toward higher symmetry, which they reflect by systematic changes in lattice parameters and an increasing shuffle parameter y.

Kai: So, Nb is pushing things toward a more stable alpha double prime structure as you add more of it into the alloy.

Mira: And oxygen plays a role too; it modifies the transformation pathways by suppressing omega phase formation at lower niobium contents while promoting the beta to alpha double prime transformation.

Lev: But they also noted that at higher niobium levels, oxygen inhibits the long range martensitic transformation, which means you end up retaining a beta phase or getting competing omega phase instead.

Title and authors: Kai: That inhibition is attributed to local lattice distortions induced by interstitial oxygen, which suggests it's acting as a defect stabilizer in some contexts.

Mira: Right, and that ties into the competition between the alpha double prime martensite and athermal omega phase formation, which they say can embrittle the material and degrade functional properties.

Lev: That’s something we have to worry about when we think about running this on actual hardware; if you get too much omega phase, it complicates error correction significantly.

Kai: The paper also addresses the crystallographic relationship between the phases, interpreting the beta to alpha prime double prime martensitic transformation as a diffusionless, cooperative lattice instability governed by coupled shear and shuffle modes.

Mira: They quantify this distinction using an orthorhombicity parameter, denoted by eta S, where it's calculated as three minus twelve y.

Lev: So they are linking the structural evolution directly to the transformation crystallography through that parameter.

Kai: They also pinpoint a compositional boundary between alpha prime and alpha double prime martensitic phases in the titanium niobium binary system at approximately five point seven at percent niobium.

Mira: That specific composition is where you see a clear change in which martensitic phase you are predominantly forming, which is important for material design.

Lev: From an engineering standpoint, knowing that boundary helps us predict where we might get undesirable microstructures when we're quenching these alloys.

Kai: Now let's talk about the suggested improvements they made to the original work itself. The authors suggest a more systematic study of lattice parameter evolution, phase stability, and phase formation across a range of compositions to clarify the relationship between alloy chemistry and microstructure.

Mira: That sounds like they recognize that their current scope is a bit narrow and need to broaden the investigation into those broader relationships to really nail down the mechanism.

Lev: I agree; for real hardware, we need those systematic studies because we can't just tweak one parameter in isolation; it’s all coupled together.

Kai: And they suggest that by combining diffraction-based phase identification with determination of the crystal structure of the phases, they aim to get a comprehensive investigation into Ti niobium oxygen alloys.

Title and authors: Mira: So, the improvement is about integrating those different characterization tools more tightly to build a more complete picture of what’s happening structurally and microstructurally.

Lev: From my side, that means we need better models because if the relationship between chemistry and microstructure is too complex, our predictive models won't work for real hardware.

Kai: To wrap things up on this paper, the main conclusion is that niobium primarily controls continuous lattice evolution and martensitic crystallography in these systems. Oxygen acts as a defect-mediated stabilizer that suppresses competing transformations without significantly altering the intrinsic crystal structure of alpha double prime.

Mira: So, we have niobium driving the structural changes and oxygen acting as a subtle defect adjuster that steers the transformation away from other phases, like omega phase formation.

Lev: That distinction is important because it tells us whether we're dealing with a fundamental shift in how the material transforms or just some localized defect interference.

Kai: This work on "The effect of Nb and O on the martensitic transformation in the Ti-Nb-O alloys" gives us a clearer picture of how these two elements interact when you are studying metastable titanium alloys subjected to solution treatment and quenching.

Mira: It really helps clarify the non linear effect of oxygen when it comes to suppressing both beta omega and beta to alpha double prime transformations, depending on the niobium content.

Lev: And for anyone building error correction systems, knowing that higher niobium content leads to inhibited long range growth of macroscopic alpha double prime is a useful constraint on what we can expect from the bulk material.

Kai: That’s what we have today regarding this paper; Nb controls the lattice evolution and crystallography, while oxygen acts as a defect stabilizer without changing the core structure of alpha double prime.

Mira: So, this research contributes to a clearer understanding of transformation mechanisms in metastable titanium alloys and gives guidance for tailoring phase stability through interstitial and substitutional alloying.

Lev: It’s helpful context for when we think about designing new materials where we need precise control over the martensitic state under operational stresses.

The paper's summary: Mira: So, to recap, this study looks at how niobium and oxygen affect phase stability in titanium niobium oxygen alloys by mapping out the transformation pathways from beta to alpha double prime and alpha prime phases.

Kai: Right, it’s basically about separating the roles: niobium is pushing the lattice structure toward a more stable state through its presence, while oxygen acts like a defect stabilizer that just keeps things from forming other competing phases.

Lev: And what this means for us building hardware is that if you increase the niobium content too much, you get trouble with long-range growth of the alpha double prime martensite; it gets confined.

Mira: Exactly. It tells us that we can't just add more niobium blindly without knowing where that compositional boundary lies, which they pinpointed around five point seven at percent niobium where the phases change their identity.

Kai: That sounds like a practical constraint for anyone designing a material meant to be quenched quickly and reliably.

Lev: It is. And the oxygen part is interesting because it doesn't change the fundamental crystal structure of alpha prime, which is good news for keeping its properties stable, but it does influence how fast things transform initially.

Mira: That’s the non-linear effect they found; oxygen suppresses both the beta to omega and beta to alpha double prime transformations at lower niobium levels, but then it shifts the pathway once that transformation gets inhibited by more niobium.

Kai: So, you have a delicate balance where oxygen is acting as a gatekeeper for which structural instability wins.

Lev: It’s like having two competing error correction mechanisms; one controlled by the solute—the niobium—and one controlled by the defects—the oxygen.

Mira: And the quantitative analysis of that atomic shuffle parameter, y, really shows this coupling between shear and shuffle modes governs how it all happens structurally.

Kai: It’s not just a passive change; the atoms are literally moving into new positions dictated by that parameter as they try to settle into a lower energy state.

Lev: That means when we talk about error correction overhead, we have to model how these coupled shear and shuffle modes interact under stress, not just one effect in isolation.

Mira: This work gives us a much clearer framework for tailoring phase stability in these metastable titanium alloys by understanding exactly how those two elements influence the transformation mechanism.

Kai: It sets up a clear path for future work: we need to systematically map out this entire landscape across different oxygen concentrations and niobium levels to truly predict the outcome.

The paper's improvements: Tom: So, we're talking about how the authors themselves suggest ways to make this research even better. They are pointing out where their current study stops working and what's missing from the picture.

Mira: Yeah, they are saying that for a real material design process you need a much broader look at the phase stability across different compositions rather than just one specific alloy set.

Kai: They want to link the structural characterization—the lattice evolution stuff we talked about—directly with how those microstructures behave when you actually quench the material.

Lev: That's good because right now, it's a bit disconnected; they need to tie the atomic shuffle parameter and orthorhombicity parameter directly into macroscopic mechanical predictions.

Mira: They suggest combining those two characterization tools more tightly so you get a complete investigation of what’s happening at the atomic level all the way up to the bulk structure.

Kai: It's about integrating those different ways of looking at it, from the simulation to the actual structural determination.

Lev: For our error correction work, that means we need better predictive models because if you can't map out this relationship reliably, your models won't work for real hardware.

Mira: They are basically advocating for a more systematic study of how these elements interact so we can tailor phase stability through specific alloying choices.

Kai: So the improvement is moving from just describing what happens in one system to building a comprehensive map that guides future material design decisions.

Lev: That’s what we need because if you can't predict where the phase boundary will be, you can't reliably design a component where that transformation is suppressed or enhanced.

Mira: And the authors are pushing for this systematic variation of oxygen concentration to see how it suppresses both transformations depending on the niobium level, which gives us a much more nuanced understanding of the mechanism.

Kai: It’s really about moving from observation to control in these complex systems.

Conclusion: Kai: So, to wrap up, this paper on "The effect of Nb and O on the martensitic transformation in the Ti-Nb-O alloys" shows that niobium dictates how much the lattice structure evolves and controls where those martensitic transformations happen crystallographically.

Mira: Right. The core finding is that niobium drives continuous lattice evolution, while oxygen acts as a defect stabilizer that manages competing phases without fundamentally changing the intrinsic crystal structure of the alpha double prime phase itself.

Lev: It means we have to be very careful when designing these alloys because if you push the niobium too high, you just get inhibited long range growth of that alpha double prime martensite, which is a problem for bulk applications.

Kai: Exactly. And oxygen's effect is non-linear; it suppresses both the beta to omega and beta to alpha double prime transformations at lower niobium levels but shifts the pathway once the transformation gets stopped by more niobium.

Mira: It really helps us understand that oxygen isn't just a passive ingredient; it's actively modifying how we get those structural changes happening in a metastable titanium alloy.

Lev: From an error correction standpoint, knowing this interplay between solute and defect is crucial for predicting the stability under operational stresses because it dictates whether you’re dealing with a fundamental shift or just localized interference.

Kai: It gives us a much clearer picture of how these two elements interact when you are studying transformation mechanisms in these materials subjected to solution treatment and quenching.

Mira: This work provides guidance for tailoring phase stability through interstitial and substitutional alloying by clearly defining the compositional boundaries that matter.

Lev: I think the most important part is seeing that even with oxygen present, you still have that coupling between shear and shuffle modes governing the transformation crystallography.

Kai: It’s a lot to process, but it sets a strong foundation for predicting how these materials will behave in real-world scenarios.

Mira: So while this paper covers Nb and O thoroughly, the next step is clearly to do those systematic studies across oxygen concentrations and different niobium levels to fully map out that stability landscape.

Lev: That’s where the complexity really lands for us; we need that data set to build reliable models for real hardware implementation.

Kristián Šalata, Dalibor Preisler, Josef Stráský, Jiří Kozlík, Lukáš Horák, Václav Holý

Department of Physics of Materials, Charles University, Prague · Department of Condensed Matter Physics, Charles University, Prague

cond-mat.mtrl-sci

Submitted: 2026-04-07

Updated: 2026-10-30

Comments: 14 pages, 16 figures, 4 tables

Journal ref: J. Appl. Cryst. (2026). 59, 1570-1583

DOI: 10.1107/S1600576726007739

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 80/100

The gist: This study examines the influence of niobium and oxygen on phase stability, crystal structure, and martensitic transformation pathways in Ti–Nb–O alloys <ref:2604.05725#pg2> because it clarifies…

Key concepts

Martensitic Transformation
This is a diffusionless structural change where one crystal structure transforms into another without atoms moving significantly. In these alloys, it involves the transformation from a high-temperature β phase to lower-temperature martensite phases like α'' or α'. Nb and O influence how this transformation occurs.
Shuffle Parameter (y)
This parameter quantifies structural evolution during the transformation. It increases with Nb content, indicating a shift toward β-phase symmetry. A higher 'y' value reflects the structural change happening between the parent phase and the resulting martensite structure.
Orthorhombicity Parameter (IS)
This metric measures how much a martensitic phase deviates from perfect hexagonal symmetry. It is calculated using the formula IS = 3 - 12y. A value of IS indicates the degree of orthorhombic distortion in the α'' martensite structure.
Defect-Mediated Stabilization
Oxygen acts as a defect stabilizer, meaning it doesn't change the fundamental crystal structure itself but instead creates local lattice distortions. These distortions help suppress competing transformations, such as the formation of the ω phase, by hindering long-range growth.

Terminology

Summary

This study examines the influence of niobium and oxygen on phase stability, crystal structure, and martensitic transformation pathways in Ti–Nb–O alloys <ref:2604. p. 0

Where the paper says it

salata@matfyz. cz Abstract This study examines the influence of niobium and oxygen on phase stability, crystal structure, and martensitic transformation pathways in Ti–Nb–O alloys.

05725#pg2> because it clarifies the distinct roles of these elements in governing the martensitic transformation and competitive phase formation <ref:2604. p. 2
Where the paper says it

By combining diffraction-based phase identification, determination of crystal structure of the phases and microstructural observations, the study seeks to investigate the distinct roles of niobium and oxygen and their specific impact on the crystal structure. Special focus is placed on the interplay between these elements in governing the martensitic transformation and the competitive formation of 𝛼′′, 𝛽 and 𝜔 phases.

05725#pg4>.

Phase Stability and Transformation Pathways

The results demonstrate that Nb primarily governs α″ martensite evolution, as increasing Nb stabilizes the β phase and shifts the α″ structure toward higher symmetry, which is reflected by systematic changes in lattice parameters and an increasing shuffle parameter y <ref:2604.05725#pg2>. Oxygen modifies transformation pathways by suppressing the ω phase formation at lower Nb contents while promoting β→α″ transformation, but at higher Nb levels it inhibits long-range martensitic transformation resulting in retained β or competing ω phase <ref:2604. p. 0

Where the paper says it

Oxygen, in contrast, modifies transformation pathways. At lower Nb contents, it suppresses the ω phase formation and promotes β→α″ transformation, while at higher Nb levels it inhibits long-range martensitic transformation, resulting in retained β or competing ω phase.

05725#pg2>. These effects are attributed to local lattice distortions induced by interstitial oxygen <ref:2604. p. 0
Where the paper says it

At lower Nb contents, it suppresses the ω phase formation and promotes β→α″ transformation, while at higher Nb levels it inhibits long-range martensitic transformation, resulting in retained β or competing ω phase. These effects are attributed to local lattice distortions induced by interstitial oxygen.

05725#pg2>.

Crystallographic Relationship and Martensite Structure

The β → α′/α″ martensitic transformation is interpreted as a diffusionless, cooperative lattice instability governed by coupled shear–shuffle modes <ref:2604.05725#pg2>. The orthorhombic αʹʹ martensite is characterized by a lower degree of transformation relative to the hexagonal limit compared to the hexagonal α′ phase <ref:2604. p. 3

Where the paper says it

4 hexagonal sites) results in the formation of the hexagonal αʹ phase, the orthorhombic αʹʹ martensite is characterized by a lower degree of transformation relative to this hexagonal limit. Therefore, the orthorhombic martensite (αʹʹ) has lower symmetry than both β (bcc) and αʹ (hcp) phase.

05725#pg2>. This distinction is quantified by the orthorhombicity parameter ηS, where ηS = 3 − 12y <ref:2604. p. 4
Where the paper says it

• At y = 1/4 - the atoms remain in their relative positions from the parent β phase, representing a state where the shuffle has not yet occurred. To evaluate the progression of the transformation in our Ti-Nb alloys, we utilize the orthorhombicity parameter to determine the deviation from the hexagonal limit: 𝜂𝑆 = 𝑦− 1 4 1 6 − 1 4 = 3 − 12𝑦.

05725#pg2>. The compositional boundary between α′ and αʹʹ martensitic phases in the Ti–Nb binary system lies at approximately 5. p. 4
Where the paper says it

Whether αʹ or αʹʹ will appear upon quenching depends mainly on the concentration of solute atoms. In the Ti–Nb binary system, the compositional boundary between α′ and αʹʹ martensitic phases has been reported from first‑principles calculation to lie at approximately 5.

7 at.% Nb <ref:2604.05725#pg2>.

Influence of Niobium on Lattice Evolution

Lattice parameters were determined via Rietveld refinement, showing that parameter a increases with Nb content, while b and c decrease <ref:2604.05725#pg2>. This behavior reflects Nb’s tendency to retain eightfold coordination characteristic of the β phase <ref:2604. p. 9

Where the paper says it

The martensitic structure observed by SEM (Fig. 4) appears to be characteristic of "massive" type martensite consisting of lamellar colonies containing several parallel plates.

05725#pg2>. Increasing Nb content promotes orthorhombic symmetry αʹʹ in competition with the fully sheared hcp α′ martensite as it requires lower principal strains <ref:2604. p. 2
Where the paper says it

The precise relationship between β-stabilizer content, oxygen concentration and α'' martensite formation is still not fully explored. Additionally, the competition between α'' martensite and athermal ω-phase formation - a common issue in lean β-alloys requires further investigation, as ω phase formation can embrittle the material and degrade functional properties.

05725#pg2>. The shuffle parameter y increased with Nb concentration, reflecting structural evolution toward β-phase symmetry and highlighting the strong coupling between shuffle and shear processes governing transformation crystallography <ref:2604. p. 0
Where the paper says it

The results demonstrate that Nb primarily governs α″ martensite evolution. Increasing Nb stabilizes the β phase and shifts the α″ structure toward higher symmetry, as reflected by systematic changes in lattice parameters and increasing shuffle parameter y, indicating suppression of transformation toward the hexagonal α′ phase.

05725#pg2>.

Role of Oxygen as a Defect Stabilizer

Oxygen acts as a defect-mediated stabilizer that suppresses competing transformations without significantly altering the intrinsic crystal structure of αʹʹ <ref:2604.05725#pg2>. At lower Nb content, oxygen primarily acts to suppress the β→ω transformation and redirects the structure toward the pure martensitic αʹʹ phase <ref:2604. p. 0

Where the paper says it

The results demonstrate that Nb primarily governs α″ martensite evolution. Increasing Nb stabilizes the β phase and shifts the α″ structure toward higher symmetry, as reflected by systematic changes in lattice parameters and increasing shuffle parameter y, indicating suppression of transformation toward the hexagonal α′ phase.

05725#pg2>. In more β stabilized alloys with high niobium content, oxygen inhibits the long-range growth of macroscopic αʹʹ <ref:2604. p. 1
Where the paper says it

%) have attracted significant attention due to their exceptional mechanical properties, including low elastic modulus, high strength, superelasticity, excellent cold workability and invar-like behaviour [11]. Unlike conventional martensite, which forms via diffusionless displacive mechanism involving a coupled shear and shuffle [12, 13], the presence of defects caused by increased oxygen content and/or β-stabilizer content can frustrate the long-range ordering, leading to the formation of nanoscale martensitic domains or “strain-glass” states instead of macroscopic martensite plates as reported in several studies [14–16].

05725#pg2>. This suggests that oxygen generates local stress fields that hinder long-range martensitic transformation rather than producing a significant change in the intrinsic crystal structure of αʹʹ <ref:2604. p. 1
Where the paper says it

Oxygen atoms occupying interstitial sites generate local lattice distortions and strain fields that can stabilize orthorhombic α″ martensite by modifying its lattice parameters and increasing the reverse transformation temperature [20]. At the same time, these strain fields promote the formation of nanoscale modulated domains in the parent β phase, which act as barriers to the development of long-range martensitic transformation [21].

05725#pg2>.

Conclusion on Interplay of Elements

Overall, the combined structural and microstructural analysis establishes that niobium primarily controls continuous lattice evolution and martensitic crystallography, whereas oxygen acts as a defect-mediated stabilizer that suppresses competing transformations without significantly altering the intrinsic crystal structure of αʹʹ <ref:2604.05725#pg2>. The findings contribute to a clearer understanding of transformation mechanisms in metastable Ti alloys and provide guidance for tailoring phase stability through interstitial and substitutional alloying <ref:2604. p. 2

Where the paper says it

By uncovering these underlying mechanisms of lattice stability in the presence of interstitial solutes, this work contributes to the broader understanding required for the rational design of next-generation lowmodulus biomedical titanium alloys. Crystallographic relation between β and α″/αʹ phase The β → α′/α″ martensitic transformation in metastable bcc alloys is most rigorously interpreted as a diffusionless, cooperative lattice instability governed by coupled shear–shuffle modes.

05725#pg2>.

Quantitative Analysis and Variant Indexation

To distinguish individual variants of martensite, the researchers simulated the reciprocal space in the range from (hkl) = (7̅7̅7̅)αʹʹ to (hkl) = (777)αʹʹ <ref:2604.05725#pg2>. The representative value of the y coordinate was obtained by averaging the values refined for the individual variants <ref:2604. p. 6

Where the paper says it

As the martensitic variants are mutually related through the orientation relationship, the presence of retained β phase was not required for determination of the orientation. This approach enabled us to distinguish the individual martensitic variants and allowed reciprocal-space maps corresponding to each variant to be refined separately.

05725#pg2>. This trend indicates that higher solute concentrations hinder the atoms from reaching the positions required for hexagonal symmetry during the β to α′ transformation <ref:2604. p. 4
Where the paper says it

• At y = 1/6 - the shuffle is complete, and the structure degenerates into the hexagonal αʹ phase (provided the lattice ratio also matches - 𝑏/𝑎 is equal to √3 to have 60° angle between three neighbouring atoms in one plane and thus hexagonal symmetry). • At y = 1/4 - the atoms remain in their relative positions from the parent β phase, representing a state where the shuffle has not yet occurred.

05725#pg2>. The shuffle parameter increased with Nb concentration, reflecting structural evolution toward β-phase symmetry and highlighting the strong coupling between shuffle and shear processes governing transformation crystallography <ref:2604. p. 0
Where the paper says it

The results demonstrate that Nb primarily governs α″ martensite evolution. Increasing Nb stabilizes the β phase and shifts the α″ structure toward higher symmetry, as reflected by systematic changes in lattice parameters and increasing shuffle parameter y, indicating suppression of transformation toward the hexagonal α′ phase.

p. 0
Where the paper says it

The results demonstrate that Nb primarily governs α″ martensite evolution. Increasing Nb stabilizes the β phase and shifts the α″ structure toward higher symmetry, as reflected by systematic changes in lattice parameters and increasing shuffle parameter y, indicating suppression of transformation toward the hexagonal α′ phase.

05725#pg2>.

Oxygen's Effect on Transformation Pathway

The systematic disappearance of the ω phase upon further increase of oxygen content demonstrates that oxygen effectively suppresses ω formation within the β-rich matrix <ref:2604.05725#pg2>. This parallels trends in Ti-16Nb alloys, where moderate oxygen additions initially suppress ω formation but allow its reappearance once martensitic transformation is inhibited, implying a shift in transformation pathway toward β decomposition into ω rather than β → αʹʹ <ref:2604. p. 1

Where the paper says it

Unlike conventional martensite, which forms via diffusionless displacive mechanism involving a coupled shear and shuffle [12, 13], the presence of defects caused by increased oxygen content and/or β-stabilizer content can frustrate the long-range ordering, leading to the formation of nanoscale martensitic domains or “strain-glass” states instead of macroscopic martensite plates as reported in several studies [14–16]. Interstitial oxygen plays a nontrivial role in the phase stability and transformation behaviour of metastable β-titanium alloys.

05725#pg2>. The combined XRD results demonstrate that oxygen strongly modifies transformation pathways in Ti–Nb alloys, revealing the non-linear effect of oxygen to suppress the αʹ/ ω formation <ref:2604. p. 0
Where the paper says it

Oxygen, in contrast, modifies transformation pathways. At lower Nb contents, it suppresses the ω phase formation and promotes β→α″ transformation, while at higher Nb levels it inhibits long-range martensitic transformation, resulting in retained β or competing ω phase.

05725#pg2>.

Microstructural Manifestations

SEM observations confirmed that alloys containing up to 20 at.% Nb exhibited irregular martensitic plate morphologies characteristic of diffusionless transformation products <ref:2604. p. 1

Where the paper says it

Unlike conventional martensite, which forms via diffusionless displacive mechanism involving a coupled shear and shuffle [12, 13], the presence of defects caused by increased oxygen content and/or β-stabilizer content can frustrate the long-range ordering, leading to the formation of nanoscale martensitic domains or “strain-glass” states instead of macroscopic martensite plates as reported in several studies [14–16]. Interstitial oxygen plays a nontrivial role in the phase stability and transformation behaviour of metastable β-titanium alloys.

05725#pg2>. Higher-Nb alloys stabilized in the β phase displayed coarse prior-β grains exceeding 1 mm in size, consistent with prolonged high-temperature solution treatment <ref:2604.05725#pg2>. The random distribution of nanodomains prevents their cooperative growth into long-range martensite, thereby stabilizing the β matrix <ref:2604. p. 1
Where the paper says it

%) have attracted significant attention due to their exceptional mechanical properties, including low elastic modulus, high strength, superelasticity, excellent cold workability and invar-like behaviour [11]. Unlike conventional martensite, which forms via diffusionless displacive mechanism involving a coupled shear and shuffle [12, 13], the presence of defects caused by increased oxygen content and/or β-stabilizer content can frustrate the long-range ordering, leading to the formation of nanoscale martensitic domains or “strain-glass” states instead of macroscopic martensite plates as reported in several studies [14–16].

05725#pg2>. The results are consistent with recent studies demonstrating that oxygen at higher concentrations suppress the formation of macroscopic α” martensite upon quenching and instead promote the formation of nanodomains structure <ref:2604. p. 1
Where the paper says it

%) have attracted significant attention due to their exceptional mechanical properties, including low elastic modulus, high strength, superelasticity, excellent cold workability and invar-like behaviour [11]. Unlike conventional martensite, which forms via diffusionless displacive mechanism involving a coupled shear and shuffle [12, 13], the presence of defects caused by increased oxygen content and/or β-stabilizer content can frustrate the long-range ordering, leading to the formation of nanoscale martensitic domains or “strain-glass” states instead of macroscopic martensite plates as reported in several studies [14–16].

05725#pg2>.

Quantitative Analysis of Shuffle Parameter

The refined theoretical values of structure factor were listed in Table 3, yielding a representative value of y = 0.212 for Ti-20Nb <ref:2604. p. 5

Where the paper says it

03 Ti − 16Nb − 3O 2. 01 Ti − 20Nb 0.

05725#pg2>. This shift indicates that higher solute concentrations hinder the atoms from reaching the positions required for hexagonal symmetry during the β to α′ transformation <ref:2604. p. 4
Where the paper says it

• At y = 1/6 - the shuffle is complete, and the structure degenerates into the hexagonal αʹ phase (provided the lattice ratio also matches - 𝑏/𝑎 is equal to √3 to have 60° angle between three neighbouring atoms in one plane and thus hexagonal symmetry). • At y = 1/4 - the atoms remain in their relative positions from the parent β phase, representing a state where the shuffle has not yet occurred.

05725#pg2>. The refined values remain constant across the investigated oxygen concentrations for Ti-12Nb-xO, indicating that oxygen addition does not produce a measurable modification of the atomic shuffle along the b-axis under the present experimental conditions <ref:2604.05725#pg2>.

Final Summary of Roles

Niobium primarily controls continuous lattice evolution and martensitic crystallography, while oxygen acts as a defect-mediated stabilizer that suppresses competing transformations without significantly altering the intrinsic crystal structure of αʹʹ <ref:2604.05725#pg2>. This work investigates the influence of niobium and oxygen on phase stability and crystal structure in Ti–Nb–O alloys subjected to solution treatment and quenching <ref:2604. p. 0

Where the paper says it

salata@matfyz. cz Abstract This study examines the influence of niobium and oxygen on phase stability, crystal structure, and martensitic transformation pathways in Ti–Nb–O alloys.

05725#pg2>. The results demonstrate that the lattice of orthorhombic αʹʹ martensite evolves continuously with decreasing niobium concentration, bridging the crystallographic characteristics of the parent bcc β phase and the stable αʹ hcp structure <ref:2604. p. 3
Where the paper says it

4 hexagonal sites) results in the formation of the hexagonal αʹ phase, the orthorhombic αʹʹ martensite is characterized by a lower degree of transformation relative to this hexagonal limit. Therefore, the orthorhombic martensite (αʹʹ) has lower symmetry than both β (bcc) and αʹ (hcp) phase.

05725#pg2>. Systematic variation of oxygen concentration revealed a general suppressing effect on both β→ω and β→αʹʹ transformations, though the dominant pathway depends on the niobium content <ref:2604.05725#pg2>. The shuffle parameter increased with Nb concentration, reflecting structural evolution toward β-phase symmetry and highlighting the strong coupling between shuffle and shear processes governing transformation crystallography <ref:2604.05725#pg2>.

Acknowledgements

This work was supported by the Czech Science Foundation (Project No. 21-18652M) <ref:2604.05725#pg2>. Additional financial support was provided by the Operational Programme Johannes Amos Comenius of the Ministry of Education, Youth and Sports of the Czech Republic, within the project Ferroic Multifunctionalities (FerrMion) (Project No. p. 0

Where the paper says it

1 The effect of Nb and O on the martensitic transformation in the Ti-Nb-O alloys. Kristián Šalata, 1* , Dalibor Preisler1 , Josef Stráský1 , Jiří Kozlík1 , Lukáš Horák2 , Václav Holý2 1 Department of Physics of Materials, Charles University, Prague, Ke Karlovu 5, Czech Republic 2 Department of Condensed Matter Physics, Charles University, Prague, Ke Karlovu 5, Czech Republic *Corresponding author: kristian.

CZ.02.01.01/00/22 008/ 0 4591), co-funded by the European Union <ref:2604.05725#pg2>. The authors also acknowledge the use of the MGML facilities (mgml.eu), supported within the programme of Czech Research Infrastructures (Project No. p. 0
Where the paper says it

1 The effect of Nb and O on the martensitic transformation in the Ti-Nb-O alloys. Kristián Šalata, 1* , Dalibor Preisler1 , Josef Stráský1 , Jiří Kozlík1 , Lukáš Horák2 , Václav Holý2 1 Department of Physics of Materials, Charles University, Prague, Ke Karlovu 5, Czech Republic 2 Department of Condensed Matter Physics, Charles University, Prague, Ke Karlovu 5, Czech Republic *Corresponding author: kristian.

LM2023065) <ref:2604.05725#pg2>.

Data Availability

The data that support the findings of this study are openly available in the Zenodo repository at https://doi.org/10.5281/zenodo.19087995 under the CC-BY 4.0 license <ref:2604.05725#pg2>.

Declaration of Generative AI and AI-Assisted Technologies in the Manuscript Preparation Process

During the preparation of this work the authors used CHAT-GPT to correct the grammar and polish the sentences <ref:2604.05725#pg2>. After using this tool/service, the authors reviewed and edited the content as needed and take full responsibility for the content of the published article <ref:2604. p. 5

Where the paper says it

This allows individual martensitic variants to be distinguished and their orientation to be resolved, providing essential information for accurate crystal structure refinement process. Analyses of the O content were performed using a carrier gas hot extraction (CGHE) method on three samples of each alloy - the results are summarized in Table 1.

05725#pg2>.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved AI can accurately predict which transformation pathway will dominate in Ti-Nb-O alloys based on niobium concentration and oxygen content by using the relationship described: "At lower niobium content (CNb <= 12%), oxygen primarily acts to suppress the β→ω transformation and redirects the structure toward the pure martensitic α′′ phase, whereas in more β stabilized alloys with high niobium content (CNb >= 20%), oxygen inhibits the long-range growth of macroscopic α′′."

  2. Improved AI can determine if an alloy will exhibit orthorhombic martensite by calculating a structural metric based on the atomic shuffle parameter y and the orthorhombicity parameter IS, using the formula IS = y - 1/4 - 1/6 - 1/4 = 3 - 12y.

  3. Improved AI can assess the effect of oxygen on local lattice distortions by identifying if oxygen is causing a measurable change in atomic positions, as stated: no measurable change in atomic positions was detected with increasing oxygen content, which helps distinguish between structural changes and defect-mediated suppression.

Abstract

This study examines the influence of niobium and oxygen on phase stability, crystal structure, and martensitic transformation pathways in Ti-Nb-O alloys. A series of Ti-(8-28)Nb-(0-3)O (at.%) alloys were prepared and solution-treated in the β-phase field. Microstructure and crystallography were characterized by X-ray diffraction, electron microscopy, and reciprocal-space mapping. A 2D-XRD orientation simulation approach was applied to distinguish all 12 crystallographically equivalent α" martensitic variants originating from a single prior β grain, enabling detailed diffraction analysis. This method further allowed quantitative evaluation of the atomic shuffle parameter y, describing the β toα" transformation. The results demonstrate that Nb primarily governs α" martensite evolution. Increasing Nb stabilizes the β phase and shifts the α" structure toward higher symmetry, as reflected by systematic changes in lattice parameters and increasing shuffle parameter y, indicating suppression of transformation toward the hexagonal α' phase. Oxygen, in contrast, modifies transformation pathways. At lower Nb contents, it suppresses the ω phase formation and promotes β toα" transformation, while at higher Nb levels it inhibits long-range martensitic transformation, resulting in retained β or competing ω phase. These effects are attributed to local lattice distortions induced by interstitial oxygen.

Related papers