Fixed-grid sharp-interface numerical solutions to the three-phase spherical Stefan problem
Listen
Radio episode about this paper
Transcript
Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.
Kai: We're looking at the paper: "Fixed-grid sharp-interface numerical solutions to the three-phase spherical Stefan problem".
Mira: Here's the gist of the paper. Fixed-grid sharp-interface numerical solutions to the three-phase spherical Stefan problem provides analytical and numerical solutions to a challenging three-phase Stefan problem in spherical coordinates for finite-sized particles The kinetic energy terms significantly affect the melt times of smaller particles, whereas for large particles their effect diminishes for microns and larger Problem Formulation and Governing Equations The governing equations describe the conservation of mass, momentum, and energy in the solid, liquid, and vapor phases within a spherically symmetric domain.
Kai: The problem involves three moving interfaces: the melt front, the boiling front, and the outer boundary exposed to the atmosphere The thermophysical properties of each phase, including density, thermal conductivity, and heat capacity, are distinct.
Mira: The energy equation includes terms related to surface energy and kinetic energy at the interface.
Kai: Small-Time Analytical Solutions Small-time analytical solutions are derived to initialize the numerical simulation by assuming the melt front stays close to the outer boundary and that its velocity is constant.
Paper summary: Kai: So we're looking at this paper, "Fixed-grid sharp-interface numerical solutions to the three-phase spherical Stefan problem." It deals with phase changes like melting, boiling, and vaporization happening all at once in a sphere.
Mira: It sets out to provide both analytical and numerical solutions for this really challenging three phase Stefan problem in spherical coordinates for finite sized particles.
Kai: What makes it interesting is how the kinetic energy terms affect the melt times of smaller particles versus larger ones, with a big difference between microns and larger sizes.
Lev: From an engineering side, that means we need to watch those kinetic energy terms closely because they really impact how fast things happen when you're dealing with real hardware.
Kai: The paper mentions some small time analytical solutions first to get the simulation started, like the low density ratio solution and the high density ratio solution.
Mira: The paper claims that these small time solutions are used to initialize the numerical simulation, which is a solid step toward tackling this more complex problem.
Lev: I wonder if those initial assumptions about constant velocity for the melt front really hold up when you move into the full simulation dynamics.
Kai: Moving into the numerical part, they use a fixed-grid sharp interface method with second order spatial and temporal accuracy to solve these governing equations in spherical coordinates.
Mira: They validated this method by reproducing two phase nanoparticle melting results from Font et al., which gives it some initial credibility.
Lev: And they handle the interface boundary conditions using one sided quadratic extrapolation to close the system of equations, which is a specific numerical trick for sharp interfaces.
Kai: The biggest result they show is that including kinetic energy terms significantly reduces the melt-front speed and increases the melt time from point three milliseconds to point eighteen milliseconds, which is about a forty six percent increase.
Mira: That increase in melting time suggests that kinetic energy plays a much more important role in how long it takes for the solid to turn liquid than we might have expected.
Lev: So, if we're building hardware that relies on these phase changes, that means we need to account for this kinetic energy effect when designing our cooling and heat transfer models.
Kai: The paper also notes that the liquid vapor interface shows a sensitivity to those kinetic energy terms, but for larger particles of size microns and above, those kinetic energy terms do not affect the phase change dynamics at all.
Mira: That distinction between smaller and larger particles is important because it tells us where we need to focus our modeling efforts for these specific physical processes.
Lev: So, when you're designing a system, if you're dealing with very small particles, you have to factor in the kinetic energy effects on melt times, but if the particle is bigger than a micron, that specific term becomes negligible.
Kai: The authors conclude by summarizing that they have developed a mathematical model for two and three phase spherical Stefan problems that accounts for density variations between phases.
Mira: They also say their numerical method and small time analysis are validated against literature results before solving the three phase problems, which shows they've put in some foundational work.
Lev: What I find interesting is that this whole study tackles a rather unexplored but physically relevant heat and mass transfer problem, specifically the three phase version of the classical Stefan problem.
Kai: It’s a lot to take in because modeling these simultaneous melting, boiling, and vaporization events is quite complex for real-world applications in metal manufacturing.
Mira: The implication is that this type of detailed modeling could help us better predict how materials behave when they undergo rapid phase changes under intense heat sources like lasers or during additive manufacturing processes.
Lev: For the future work, it seems like the next step would be testing this on real hardware to see how much overhead those kinetic energy corrections actually land on when you try to run a simulation.
Kai: So, we've seen the paper’s main points: they solved a three phase spherical Stefan problem numerically using a fixed grid method, and they found that kinetic energy terms matter for small particles but not for large ones.
Mira: And the authors suggest this work provides a mathematical framework that accounts for density variations during these simultaneous phase transitions.
Lev: It’s about taking a very hard problem and giving us a way to model it, which is what we need when trying to build robust error correction schemes for real hardware.
Conclusion: Kai: So this paper, "Fixed-grid sharp-interface numerical solutions to the three-phase spherical Stefan problem," is about solving that really tough problem where melting, boiling, and vaporizing all happen at once inside a sphere.
Mira: It's tackling those simultaneous phase changes using a fixed grid method in spherical coordinates for finite sized particles.
Kai: The authors are giving us both analytical and numerical solutions to this three phase Stefan problem.
Lev: They’re focusing on the kinetic energy terms, which is usually where things get tricky in these simulations because they affect how fast the melt fronts move.
Mira: They find that including those kinetic energy terms actually makes the melting time longer for smaller particles, but it doesn't matter much for larger ones above a micron.
Kai: So what does this mean for us building hardware? It means when you model systems with very tiny components, you have to account for those kinetic energy effects on melt times.
Mira: Exactly. The paper shows that the melting front is more sensitive to those kinetic energy terms than the boiling front is.
Lev: From a real hardware perspective, that means our error correction schemes need to handle these specific dynamics if we’re dealing with nanoscale material transitions.
Kai: It’s a lot of complex physics crammed into one spherical problem, and the way they validated their numerical method against other two phase nanoparticle melting results is pretty reassuring.
Mira: They've done some solid groundwork by confirming their approach on smaller problems before tackling this three phase scenario.
Lev: But the real challenge here is scaling that fixed grid method up to actually run on real hardware without introducing massive discretization errors.
Kai: This work sets up a good mathematical model for two and three phase spherical Stefan problems, which is a solid start for understanding these complex heat transfer phenomena.
Mira: It really shows how accounting for density variations between phases directly impacts the time evolution of the fronts in this system.
Lev: The next thing we need to see is how this translates into actual computational overhead on real hardware when you try to simulate something with this much complexity.
Yavkreet Swamia, Jacob Barajasa, Amneet Pal Singh Bhallaa
Department of Mechanical Engineering, San Diego State University
cond-mat.mtrl-sci, cs.NA, math.NA, physics.flu-dyn
Submitted: 2026-02-09
Updated: 2026-02-09
DOI: 10.1115/1.4072266
Code: https://github.com/amneetb/SphericalStefan
License: http://creativecommons.org/licenses/by/4.0/
Importance score: 83/100
The gist: Fixed-grid sharp-interface numerical solutions to the three-phase spherical Stefan problem provides analytical and numerical solutions to a challenging three-phase Stefan problem in spherical…
Key concepts
- Three-phase Stefan Problem
- This is a mathematical model describing heat transfer where a material changes phase (like melting or boiling) in three distinct states simultaneously—solid, liquid, and vapor—within a spherical shape. The problem involves tracking the movement of interfaces between these phases over time.
- Kinetic Energy Terms
- These terms account for the energy associated with the motion of fluid or interface boundaries during phase change. In this study, including them showed that kinetic energy influences how fast a particle melts, specifically slowing down the melt speed and increasing the total melting time.
- Fixed-Grid Sharp-Interface Method
- This is a specific numerical technique used to solve the governing equations for phase change problems. It uses a fixed spatial grid to discretize the domain and employs sharp-interface tracking methods, often using extrapolation near interfaces, to accurately model the distinct boundaries between solid, liquid, and vapor regions.
Terminology
Summary
Fixed-grid sharp-interface numerical solutions to the three-phase spherical Stefan problem provides analytical and numerical solutions to a challenging three-phase Stefan problem in spherical coordinates for finite-sized particles The kinetic energy terms significantly affect the melt times of smaller particles, whereas for large particles their effect diminishes for microns and larger
Problem Formulation and Governing Equations
The governing equations describe the conservation of mass, momentum, and energy in the solid, liquid, and vapor phases within a spherically symmetric domain. The problem involves three moving interfaces: the melt front, the boiling front, and the outer boundary exposed to the atmosphere The thermophysical properties of each phase, including density, thermal conductivity, and heat capacity, are distinct. p. 0 The problem was
set in a semi-infinite domain with two moving interfaces—melt and boiling fronts. The solid, liquid, and
vapor phases of the PCM have distinct thermophysical properties, including density, thermal conductivity,
and heat capacity. The temperature T
I
m at the S-L interface differs from the bulk melting temperature Tm due to the
curvature and surface energy/tension effects. The two temperatures are related by the Gibbs-Thomson
relation
T
I
m(R1(t)) = Tm −
σSLTm
ρ
SLm
2
R1(t)
.Where the paper says it
Where the paper says it
Small-Time Analytical Solutions
Small-time analytical solutions are derived to initialize the numerical simulation by assuming the melt front stays close to the outer boundary and that its velocity is constant. Two different small-time solutions are obtained depending on whether low or high density contrasts between phases are considered. p. 0 To derive small-time analytical solutions,
low- and high-density contrasts between phases are considered separately. Our numerical method is validated
by reproducing the two-phase nanoparticle melting results of Font et al. (10b)
1
ε
∂TrL
∂rt
−
P
ε
∂TrL
∂rr
=
1
ε
2
∂
2TrL
∂rr
2
+ O
ˆ
1
ε
˙
, (18)
yields the leading-order term that determines the small-time temperature in the liquid phase:
∂
2TrL
∂rr
2
= 0. (19)
The general solution of Eq.Where the paper says it
Where the paper says it
Numerical Methodology
A fixed-grid sharp-interface method with second-order spatio-temporal accuracy is used to solve the governing equations in spherical coordinates. The numerical method is validated by reproducing two-phase nanoparticle melting results of Font et al. p. 0 To derive small-time analytical solutions,
low- and high-density contrasts between phases are considered separately. Our numerical method is validated
by reproducing the two-phase nanoparticle melting results of Font et al. Governing equations and
boundary conditions are non-dimensionalized and small-time analytical solutions for temperature and interface positions and velocities are derived for both two- and three-phase Stefan problems. 3 presents a
sharp-interface numerical method using a second-order, finite difference/volume discretization, with explicit
tracking of moving interfaces using an immersed-boundary (IB) method [12].Where the paper says it
Where the paper says it
Results and Kinetic Energy Influence
The inclusion of kinetic energy terms significantly reduces the melt-front speed and increases the melt time from pt ≈ 0.13 to pt ≈ 0.19, which is an increase of roughly 46%. The liquid-vapor interface Rp2 exhibits a sensitivity to kinetic energy terms. p. 8 (34)
when non-dimensionalized with the scaling parameters defined previously gives
∂TpL
∂rp
ˇ
ˇ
ˇ
ˇ
ˇ
Rp2
− κ
VL ∂TpV
∂rp
ˇ
ˇ
ˇ
ˇ
ˇ
Rp2
= βv
´
up2 − (1 − ρ
SL)up1
¯
Sv, (35)
in which Sv is defined as
Sv =
«
1 + γvTpI
v −
1
2
(1 − ρ
SL)
2
δv up
2
1 +
1
2
δv
n
(ρ
LV − ρ
SV)up1 + (1 − ρ
LV)up2
o2
−
δv
n
(ρ
LV − ρ
SV)up1 + (1 − ρ
LV)up2 − (1 − ρ
SL)up1
o
up2
ff
. (36)
Here, κ
VL = κ
V/κL denotes vapor-to-liquid thermal conductivity ratio, βv = Lv/(C
L ∆T) is the (vapor)
Stefan number, γv = (C
V − C
L)∆T /Lv is the inverse Stefan number, and δv = R2
0/(Lvτ
2
) is a measure
of kinetic energy of the boiling front relative to the latent heat of vaporization. Lastly, we solve the three-phase
Stefan problems numerically to demonstrate the importance of kinetic energy terms during phase change of
smaller (nano) particles. In contrast, these effects diminish for large particles (microns and larger). Lastly, we solve the three-phase
Stefan problems numerically to demonstrate the importance of kinetic energy terms during phase change of
smaller (nano) particles. In contrast, these effects diminish for large particles (microns and larger).Where the paper says it
Where the paper says it
Where the paper says it
Conclusion
The present study presents a mathematical model for two- and three-phase spherical Stefan problems that accounts for density variations between phases. The numerical method and small-time analysis are validated against literature results before solving the three-phase problems. p. 0 Our numerical method is validated
by reproducing the two-phase nanoparticle melting results of Font et al. Lastly, we solve the three-phase
Stefan problems numerically to demonstrate the importance of kinetic energy terms during phase change of
smaller (nano) particles. Lastly, we apply the method to numerically solve the three-phase Stefan problem to quantify the influence of density and kinetic-energy terms on interface evolution. It is found that the kinetic
energy terms significantly affect the melt times of smaller particles, whereas for large particles their effect
diminishes significantly. (36)
Here, κ
VL = κ
V/κL denotes vapor-to-liquid thermal conductivity ratio, βv = Lv/(C
L ∆T) is the (vapor)
Stefan number, γv = (C
V − C
L)∆T /Lv is the inverse Stefan number, and δv = R2
0/(Lvτ
2
) is a measure
of kinetic energy of the boiling front relative to the latent heat of vaporization. The dimensional and
dimensionless version of the Stefan equation for the melt front remains the same as written in Eqs. Keywords: immersed boundary method, metal manufacturing, heat and mass transfer
1. Introduction
The Stefan problem is concerned with the evolution of an interface between two phases while simultaneously going through a phase change, such as melting a solid metal.Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
References
[1] M. Soleimani, K. Koponen, N. Tilton, A. P. S. Bhalla, Analytical and numerical solutions to the threephase stefan problem with simultaneous occurrences of melting, solidification, boiling, and condensation phenomena
[2] F. Font, T. G. Myers, S. L. Mitchell, A mathematical model for nanoparticle melting with density change
[3] C. Vuik, Some historical notes about the Stefan problem
[4] L. I. Rubinvsteuin, The Stefan problem, Vol. p. 0 Fixed-grid sharp-interface numerical solutions to the three-phase spherical
Stefan problem
Yavkreet Swamia
, Jacob Barajasa
, Amneet Pal Singh Bhallaa,
aDepartment of Mechanical Engineering, San Diego State University, San Diego, CA
Abstract
Many metal manufacturing processes involve phase change phenomena, which include melting, boiling, and
vaporization. These phenomena often occur concurrently. The foundation of Stefan’s work traces
back to 1831 when a similar problem was faced by Lamé and Clapeyron while studying the solidification of
Earth’s crust [3, 4]. Although a large body of research has been conducted to solve the Stefan problem analytically and numerically, the vast majority of studies incorporate a number of restrictive assumptions that are often justified
for mathematical convenience.Where the paper says it
Where the paper says it
[5] D. W. Hahn, M. N. Özisik, Heat conduction, John Wiley & Sons, 2012
[6] V. Alexiades, A. D. Solomon, Mathematical modeling of melting and freezing processes
[7] S. W. McCue, B. Wu, J. M. Hill, Micro/nanoparticle melting with spherical symmetry and surface tension
[8] S. W. McCue, B. Wu, J. M. Hill, Classical two-phase stefan problem for spheres
[9] F. Font, T. Myers, Spherically symmetric nanoparticle melting with a variable phase change temperature
[10] B. Wu, P. Tillman, S. W. McCue, J. M. Hill, Nanoparticle melting as a stefan moving boundary problem
[11] T. G. Myers, M. G. Hennessy, M. Calvo-Schwarzwälder, The stefan problem with variable thermophysical properties and phase change temperature
[12] K. Koponen, A. P. S. Bhalla, B. Sprinkle, N. Wu, N. Tilton, A direct forcing, immersed boundary method for conjugate heat transport
[13] N. Nangia, B. E Griffith, N A Patankar, A P S Bhalla, A robust incompressible navier-stokes solver for high density ratio multiphase flows
[14] P. Buffat, J.-P. Borel, Size effect on the melting temperature of gold particles, Physical Review A 13 (6) (1976) 2287–2297
[15] R. Thirumalaisamy, A. P. S. Bhalla, A low mach enthalpy method to model non-isothermal gas–liquid–solid flows with melting and solidification
[16] M. Doble, Perry’s chemical engineers’ handbook, McGraw-Hil, New York, US (2007)
[17] J. E Hatch, Aluminium: Properties and physical metallurgy, by asm, Metals Park OH 135 (1984)
[18] P.
Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.
Improvements for AI systems
-
Improved AI can perform second-order accurate spatio-temporal simulations of three-phase Stefan problems in spherical coordinates using a fixed grid sharp interface method to model metal manufacturing processes like melting, boiling, and vaporization.
-
The improved system can derive small time analytical solutions for two-phase and three-phase spherical Stefan problems to initialize numerical simulations, distinguishing between low density ratio scaling (LDRS) and high density ratio scaling (HDRS).
-
The AI system can quantify the influence of kinetic energy terms on interface evolution, specifically predicting that
including kinetic energy terms substantially reduces the melt-front speed and increases the melt time from pt approx 0.13 to pt approx 0.19.
-
The system can provide physical predictions regarding particle size effects, noting that for
large particles of size micrometers and above, the kinetic energy terms do not affect the phase change dynamics.
-
The improved AI can perform grid convergence studies for three-phase Stefan problems using both LDRS and HDRS initializations to demonstrate that
the method converges with better than second-order spatiotemporal accuracy for the three-phase Stefan problem.
Abstract
Many metal manufacturing processes involve phase change phenomena, which include melting, boiling, and vaporization. These phenomena often occur concurrently. A prototypical 1D model for understanding the phase change phenomena is the Stefan problem. There is a large body of literature discussing the analytical solution to the two-phase Stefan problem that describes only the melting or boiling of phase change materials (PCMs) with one moving interface. Density-change effects that induce additional fluid flow during phase change are generally neglected in the literature to simplify the math of the Stefan problem. In our recent work [1], we provide analytical and numerical solutions to the three-phase Stefan problem with simultaneous occurrences of melting, solidification, boiling, and condensation in Cartesian coordinates. Our current work builds on our previous work to solve a more challenging problem: the three-phase Stefan problem in spherical coordinates for finite-sized particles. There are three moving interfaces in this system: the melt front, the boiling front, and the outer boundary which is in contact with the atmosphere. Although an analytical solution could not be found for this problem, we solved the governing equations using a fixed-grid sharp-interface method with second-order spatio-temporal accuracy. Using a small-time analytical solution, we predict a reasonably accurate estimate of temperature (in the three phases) and interface positions and velocities at the start of the simulation. Our numerical method is validated by reproducing the two-phase nanoparticle melting results of Font et al. [2]. Lastly, we solve the three-phase Stefan problems numerically to demonstrate the importance of kinetic energy terms during phase change of smaller (nano) particles. In contrast, these effects diminish for large particles (microns and larger).
Related papers
- Structural contribution to light-induced gap suppression in Ta 2 NiSe 5
- Anatomy of fast current-induced skyrmion motion in synthetic antiferromagnets
- Magnetic control of an exciton-polariton condensate in a van der Waals magnet
- High-pressure elastic properties of GeO2 polymorphs up to 120 GPa
- Decoupling Strain-Rate Sensitivity and Deformation Length Scale Effects in Neutron-Irradiated Tungsten: A Coupled Nano-Indentation, HR-EBSD and Crystal Plasticity Study
- Magnetism modulation in Co3Sn2S2 by current-assisted domain wall motion